Siemens SIMATIC ET 200S User manual

Digital electronic module 8DO
DC24V/0.5 A (6ES7132-4BF00-0AA0)
___________________
___________________
___________________
SIMATIC
ET 200S distributed I/O
Digital electronic module 8DO DC24V/0.5 A
(6ES7132-4BF00-0AA0)
Manual
10/2015
A5E01077385
-AB
Preface
Properties
1
Diagnostics
2

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E01077385-AB
Ⓟ
10/2015 Subject to change
Copyright © Siemens AG 2007 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 3
Preface
Purpose of the manual
This manual supplements the ET 200S Distributed I/O System Operating Instructions.
General functions for the ET 200S are described in the ET 200S Distributed I/O System
Operating Instructions (http://support.automation.siemens.com/WW/view/en/1144348).
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Basic knowledge requirements
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of the manual
This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
Recycling and disposal
Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For
environmentally compliant recycling and disposal of your electronic waste, please contact a
company certified for the disposal of electronic waste.
Additional support
If you have any questions relating to the products described in this manual and do not find
the answers in this document, please contact your local Siemens representative
(http://www.siemens.com/automation/partners).
A guide to the technical documentation for the various SIMATIC products and systems is
available on the Internet. (http://www.siemens.com/simatic-docu).
The online catalog and ordering systems are available on the Internet
(http://www.siemens.com/automation/mall).

Preface
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
4Manual, 10/2015, A5E01077385-AB
Training center
We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in
D -90327, Nuremberg, Germany (http://www.siemens.com/sitrain).
Technical Support
You can contact Technical Support for all Industry Automation products by means of the
Internet Web form for the Support Request
(http://www.siemens.com/automation/csi_en_WW/support_request).
Additional information about Siemens Technical Support is available on the Internet
(http://www.siemens.com/automation/csi_en_WW/service).
Service & Support on the Internet
In addition to our documentation, we offer a comprehensive knowledge base on the Internet
(http://www.siemens.com/automation/csi_en_WW/support).
There you will find:
●Our Newsletter, which constantly provides you with the latest information about your
products.
●The right documentation for you using our Service & Support search engine.
●The bulletin board, a worldwide knowledge exchange for users and experts.
●Your local contact for Automation & Drives in our contact database.
●Information about on-site services, repairs, spare parts, and lots more.

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 5
Table of contents
Preface ................................................................................................................................................... 3
1 Properties ............................................................................................................................................... 6
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)....................................6
2 Diagnostics ........................................................................................................................................... 12
2.1 Diagnostics using LED display ...............................................................................................12
Index..................................................................................................................................................... 13

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
6Manual, 10/2015, A5E01077385-AB
Properties
1
1.1
Digital electronic module 8DO DC24V/0.5 A
(6ES7132-4BF00-0AA0)
Properties
●Digital electronic module with eight outputs
●Output current 0.5 A per output, total current 4 A
●Rated load voltage 24 V DC
●Short-circuit protection
●Suitable for solenoid valves, DC contactors, and indicator lights
●Supports isochronous operation
Special features
When the rated load voltage 24 V DC is applied to the power module via a mechanical
contact, the digital outputs carry a "1" signal for about 50 μs for switching reasons. You have
to take this into consideration if you use this module in connection with high-speed counters.
Requirements for operation
It is possible to operate the 8DO DC24V 0.5A digital electronic module using the following
interface modules with the order numbers specified (or higher). The interface modules listed
in the table are not subject to any constraints.
Interface module
Order number (or higher)
Firmware version (or
higher)
IM 151-1 STANDARD 6ES7151-1AA03-0AB0 ---
IM 151-1 FO STANDARD
6ES7151-1AB02-0AB0
---
IM 151-1 HIGH FEATURE
6ES7151-1BA01-0AB0
V2.1.3
IM 151-3 PN
IM 151-3 PN HIGH FEATURE
IM 151-3 PN FO
6ES7151-3AA20-0AB0
6ES7151-3BA20-0AB0
6ES7151-3BB21-0AB0
V4.0.1

Properties
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 7
General terminal assignment
Note
Terminals A4, A8, A3 and A7 are only available at specified terminal modules.
Terminal assignment for 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)
Terminal
Allocation
Terminal
Allocation
Notes
1
DO
0
5
DO
1
•DOn: Output signal, channel n
•AUX1: Mass M (from power module) or voltage bus (freely usable
up to 230 V AC)
2
DO2
6
DO3
3
DO
4
7
DO
5
4
DO6
8
DO7
A4
AUX1
A8
AUX1
A3
AUX1
A7
AUX1
Usable terminal modules
Usable terminal modules for 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)
TM-E15C26-A1
(6ES7193-4CA50-0AA0)
TM-E15C24-01
(6ES7193-4CB30-0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-0AA0)
TM-E15S24-01
(6ES7193-4CB20-0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-0AA0)
TM-E15N24-01
(6ES7193-4CB70-0AA0)
Fast Connect

Properties
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
8Manual, 10/2015, A5E01077385-AB
2-wire connection
The following configuration example shows a two-wire connection with the electronic
modules 8DO DC24V. You require further terminals so that sufficient terminals are available
for the mass M connection when the TM-E15S26-A1 terminal modules are used. In the
example this is implemented by the add-on terminal TE-U120S4x10, which you can mount
as of a width of 120 mm (8 EMs). You can naturally also use other terminals for this
configuration (for example, ET 200S potential distribution module 4POTDIS).
①
Terminal module TM-P15S23-A0
②
Power module PM-E 24 VDC
③
Electronic modules 8DI DC24V
④
Terminal modules TM-E15S26-A1
⑤
Actuator in 2-wire connection
⑥
Add-on terminal TE-U120S4x10

Properties
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 9
Block diagram
Figure 1-1 Block diagram of the 8DO DC24V 0.5A

Properties
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
10 Manual, 10/2015, A5E01077385-AB
Technical specifications 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)
Technical specifications 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)
Dimensions and weight
Width (mm)
15
Weight
Approx. 40 g
Module-specific data
Supports isochronous operation
Yes
Number of outputs
8
Cable length
•Unshielded Max. 600 m
•Shielded Max. 1000 m
Parameter length
3 bytes
Address space
1 byte
Voltages, currents, potentials
Rated Rated load voltage L+ (from power mod-
ule)
24 V DC
•Polarity reversal protection Yes 1
Total current of the outputs (per module)
4 A
Electrical isolation
•Between the channels No
•Between the channels and backplane bus Yes
Permissible potential difference
•Between different circuits 75 V DC / 60 V AC
Isolation tested
500 V DC
Current consumption
•From the rated load voltage L+ (no load) Max. 5 mA per channel
Power loss of the module
Typically 1.5 W
Status, interrupts, diagnostics
Status display
Green LED per channel
Diagnostics functions
No

Properties
1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 11
Technical specifications 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)
Actuator selection data
Output voltage
•At signal "1" Min. L+ (-1 V)
Output current
•At signal "1"
–Rated value
–Permissible range
0.5 A
7 mA to 0.6 A
•At "0" signal (residual current) Max. 0.3 mA
Output delay (with resistive load)
•At "0" to "1" Max. 300 µs
•At "1" to "0" Max. 600 µs
Load resistance range
48 Ωto 3.4 kΩ
Lamp load
Max. 5 W
Parallel switching of 2 outputs
•For redundant control of a load Yes (per module)
•For increased performance No
Control of a digital input
Yes
Switching frequency
•With resistive load 100 Hz
•With inductive load 2 Hz
•With lamp load 10 Hz
Limiting (internal) of inductive shut-down voltage
Typ. L+ (-55 to -60 V)
Reverse-voltage proof Yes, if using the same load voltage as at the
power module
Short-circuit protection of the output
Yes
2
•Response threshold Typ. 1.5 A
1)
Polarity reversal can lead to the digital outputs being switched through.
2
per channel

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
12 Manual, 10/2015, A5E01077385-AB
Diagnostics
2
2.1
Diagnostics using LED display
LED display
①
Status display for output status (green)
Status and error displays
Event (LEDs)
Cause
Remedy
1
5
2
6
3
7
4
8
On
Output on channel 0 activated.
—
On
Output on channel 1 activated.
—
On
Output on channel 2 activated.
—
On
Output on channel 3 activated.
—
On
Output on channel 4 activated.
—
On
Output on channel 5 activated.
—
On
Output on channel 6 activated.
—
On Output on channel 7 activated. —

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
Manual, 10/2015, A5E01077385-AB 13
Index
2
2-wire connection, 8
B
Basic knowledge requirements, 3
Block diagram, 9
D
Disposal, 3
I
Internet
Service & Support, 4
L
LED display, 12
P
Properties, 6
R
Recycling, 3
S
Scope
Manual, 3
Service & Support, 4
T
Technical specifications, 10
Technical Support, 4
Terminal assignment, 7
Training Center, 4

Index
Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)
14 Manual, 10/2015, A5E01077385-AB