Siemens SIPROTEC 7SD80 User manual

C53000-L2040-C347-1
SIPROTEC
Line Differential Protection
7SD80
Communication Module
DNP 3.0
Buss Mapping / Point List
Preface
Contents
Notes to SIPROTEC objects 1
DNP V3.0 Device Profile 2
Point lists 3
Glossary
Index

Disclaimer of Liability
We have checked the contents of this manual against the hardware
and software described. However, deviations from the description
cannot be completely ruled out, so that no liability can be accepted
for any errors or omissions contained in the information given
The information given in this document is reviewed regularly and
any necessary corrections will be included in subsequent editions.
We appreciate any suggested improvements.
We reserve the right to make technical improvements without
notice.
Document release: 01.00.01
Edition 07.2011
Copyright
Copyright © SIEMENS AG 2011. All rights reserved.
Dissemination or reproduction of this document, or evaluation and
communication of its contents, is not authorized except where
expressly permitted. Violations are liable for damages. All rights
reserved, particularly for the purposes of patent application or
trademark registration.
Registered trademarks
SIPROTEC, SINAUT, SICAM and DIGSI are registered trademarks
of Siemens AG. Other designations in this manual might be
trademarks whose use by third parties for their own purposes
would infringe the rights of the owner.
NOTE
For your own safety, please observe the warnings and safety instructions contained in this document.

3SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Preface
Purpose of This Manual
The manual is devided into the following topics:
•Notes to SIPROTEC objects
•DNP V3.0 Device Profile
•Point lists
General information about design, configuration, and operation of SIPROTEC devices are laid
down in the SIPROTEC 4 system manual, order no. E50417-H1176-C151.
Target Audience
Protection engineers, commissioning engineers, persons who are involved in setting, testing and
service of protection, automation, and control devices, as well as operation personnel in electri-
cal plants and power stations.
Additional literature
This manual describes the DNP 3.0 Device Profile of the SIPROTEC devices.
The following additional manuals inform you about the DNP point lists and the function, opera-
tion, assembly and commissioning of the SIPROTEC devices:
Manual Contents Order number
Line Differential Protection
SIPROTEC 7SD80
Function, operation, assembly and
commissioning of the SIPROTEC device 7SD80
C53000-G1140-C474-1
DNP 3.0 Communication
Database
DNP communication database of the
SIPROTEC devices
C53000-L1840-A001-03

Preface
4SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
The DNP V3.0 specification and the structure of the DNP messages are defined in:
>DNP V3.00 Subset Definitions
Edition 2.00, November 1995
DNP Users Group,
Document Nr.: P009-OIG.SUB
>DNP V3.00 Data Object Library
Edition 0.02, July 1997
DNP Users Group
Document Nr.: P009-OBL
>DNP V3.00 Data Link Layer
Edition 0.02, May 1997
DNP Users Group
Document Nr.: P009-OPD.DL
>DNP V3.00 Application Layer
Edition 0.03, May 1997
DNP Users Group
Document Nr.: P009-OPD.APP
>DNP V3.00 Transport Functions
Edition 0.01, May 1997
DNP Users Group
Document Nr.: P009-OPD.TF
Applicability of this Manual
This manual is valid for
•SIPROTEC devices 7SD80 with
−firmware version 4.6 and
−DNP communication module version 02.00.01 or higher.
For device parameterization DIGSI 4version 4.xx or higher and DNP standard mappings 3-1
to 3-n (n = device type dependent number of standard mappings) have to be used.
Additional Support
Should further information on the System SIPROTEC 4 be desired or should particular problems
arise which are not covered sufficiently for the purchaser's purpose, he matter should be referred
to the local Siemens representative.
Our Customer Support Center provides a 24-hour service.
Phone: +49 -180 - 5 24 70 00
Fax: +49 -180 - 5 24 24 71
e-mail: [email protected]
Training courses
Enquiries regarding individual training courses should be addressed to our
Training Center:
Siemens AG
Power Transmission and Distribution
Power Training Center
Humboldtstr. 59
90459 Nuremberg
Germany
Phone: +49 - (911) - 433 7415
Fax: +49 - (911) - 433 7929
eMail power-academy[email protected]
Internet: www.siemens.com/energy/power-academy

Preface
5SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Instructions and Warnings
The warnings and notes contained in this manual serve for your own safety and for an appropri-
ate lifetime of the device. Please observe them!
The following terms are used:
DANGER
indicates that death, severe personal injury or substantial property damage will result if proper
precautions are not taken.
Warning
indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.
Caution
indicates that minor personal injury or property damage can result if proper precautions are not
taken. This particularly applies to damage on or in the device itself and consequential damage
thereof.
Note
indicates information about the device or respective part of the instruction manual which is
essential to highlight.
QUALIFIED PERSONNEL
For the purpose of this instruction manual and product labels, a qualified person is one who is
familiar with the installation, construction and operation of the equipment and the hazards
involved. In addition, he has the following qualifications:
•Is trained and authorized to energize, de-energize, clear, ground and tag circuits
and equipment in accordance with established safety practices.
•Is trained in the proper care and use of protective equipment in accordance with
established safety practices.
•Is trained in rendering first aid.
Warning!
Hazardous voltages are present in this electrical equipment during operation. Non–observance
of the safety rules can result in severe personal injury or property damage.
Only qualified personnel shall work on and around this equipment after becoming thoroughly
familiar with all warnings and safety notices of this manual as well as with the applicable safety
regulations.
The successful and safe operation of this device is dependent on proper handling, installation,
operation, and maintenance by qualified personnel under observance of all warnings and hints
contained in this manual.
In particular the general erection and safety regulations (e.g. IEC, DIN, VDE, EN or other national
and international standards) regarding the correct use of hoisting gear must be observed. Non–
observance can result in death, personal injury or substantial property damage.

Preface
6SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Typographic and Symbol Conventions
The following text formats are used when literal information from the device or to the device
appear in the text flow:
Parameter names, i.e. designators of configuration or function parameters which may appear
word-for-word in the display of the device or on the screen of a personal computer (with opera-
tion software DIGSI 4), are marked in bold letters of a monospace type style.
Parameter options, i.e. possible settings of text parameters, which may appear word-for-
word in the display of the device or on the screen of a personal computer (with operation soft-
ware DIGSI 4), are written in italic style, additionally.
“Annunciations”, i.e. designators for information, which may be output by the relay or required
from other devices or from the switch gear, are marked in a monospace type style in quotation
marks.
Deviations may be permitted in drawings when the type of designator can be obviously derived
from the illustration.

7SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Notes to SIPROTEC objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Binary Inputs / Annunciations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.1.1 Error with a summary alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.1.2 Alarm Summary Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.1.3 Stop Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 Binary Outputs / Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.1 Single Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.2 Control mode REMOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2.3 Changing the setting group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.3 Analog Inputs / Measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.4 Metered measurands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2 DNP V3.0 Device Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Implementation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 Device Profile Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3 Point lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Binary Input Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.1 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.2 Automatic recloser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.3 Direct Transfer Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.4 Time Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.5 Thermal overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.6 Circuit breaker test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.7 Measurement supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.8 Diagnosis / General alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.9 Internal mode status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1.10 Setting group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1.11 User-allocated single-point indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2 Control Relay Output Blocks/Binary Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.1 Internal commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.2 User-allocated single commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3 Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.1 Recorded measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.2 Statistic values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

9SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
1 Notes to SIPROTEC objects
This chapter contains notes for the use and evaluation of certain SIPROTEC objects which are available via
DNP3.0 communication.
The description of the standard mappings / point lists (refer to chapter 3) contains the pre-allocation of the map-
ping files at delivery or first assignment of a mapping in DIGSI 4 to the SIPROTEC device.
Changes of the allocation and the scaling of the measured values are possible in adaptation to the concrete
installation enviroment.
1.1 Binary Inputs / Annunciations 10
1.2 Binary Outputs / Commands 11
1.3 Analog Inputs / Measured values 12
1.4 Metered measurands 13

1 Notes to SIPROTEC objects
1.1 Binary Inputs / Annunciations
10 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
1.1 Binary Inputs / Annunciations
1.1.1 Error with a summary alarm
The "Error with a summary alarm" is ON if at least one of the following internal alarms assumes the value ON:
• "Error 5V", "Error neutral CT", "Error 1A/5A wrong", "Error A/D converter".
Refere to chapter 3.1.8
1.1.2 Alarm Summary Event
The "Alarm summary event" is indicated, if at least one of the following internal alarms assumes the ON status:
• “Error Board 1“, “Error Board 2“, "Error Board 3“, "Error Board 4“, "Error Board 5“, “Error Board 0“
• "Failure Battery empty“, "Alarm Real Time Clock",
• "Failure Phase Sequence", "VT Fuse Failure", "Failure Voltage Balance", "Failure General Voltage Super-
vision",
• "Failure Current Balance", "Failure Current Summation", "Failure General Current Supervision".
Refere to chapter 3.1.8
1.1.3 Stop Data Transmission
The functionality "Stop data transmission" is not supported via DNP communication. If "Stop data transmission"
is active nevertheless data via DNP will be transmitted furthermore.
The annunciation "DataStop" signals the activation of "Stop data transmission" however and can be evaluated
correspondingly in the DNP master.
Refere to chapter 3.1.9
Note
Depending on the device composition and the existing protection packages not all of the indicated binary inputs
or protection annunciations (and corresponding DNP points) may be available in the SIPROTEC device

1 Notes to SIPROTEC objects
1.2 Binary Outputs / Commands
11SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
1.2 Binary Outputs / Commands
1.2.1 Single Commands
The command output mode (pulse output, continuous output) is changeable for the single commands using
parametrization software DIGSI 4.
The switching direction OFF for single commands with pulse output is not permitted and is rejected in the
SIPROTEC device.
Refer to chapter 3.2.2
1.2.2 Control mode REMOTE
Control mode with control authority is REMOTE, option of unlocked control with DNP.
• Changing the Control mode REMOTE“ to UNLOCKED permits one unlocked control operation via DNP.
After execution of the command, the “Control mode REMOTE“ in the SIPROTEC device will automatically
be reset to LOCKED.
• A programmed test “Switch in position“ for unlocked control operations will always be executed.
If, after changing the “Control mode REMOTE“ to UNLOCKED, no command is received via DNP for a period
of 5 minutes, then the “Control mode REMOTE“ is automatically reset to LOCKED.
Refer to chapter 3.2.1
1.2.3 Changing the setting group
Switching on one setting group automatically switches off the current active setting group. Transmission of the
value OFF is insignificant for the change of the setting group and is refused by the device.
A change of the setting group is only possible via DNP if the parameter CHANGE TO ANOTHER SETTING GROUP
(parameter address = 302) has the value "Protocol".
Refer to chapter 3.2.1
Note
The allocation of the output relays to the switching devices and to the output channels is defined during param-
etrization of the SIPROTEC devices.
Depending on the device composition there may be less than indicated output relays (and corresponding DNP
message points) available in the SIPROTEC device.

1 Notes to SIPROTEC objects
1.3 Analog Inputs / Measured values
12 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
1.3 Analog Inputs / Measured values
The given scaling values for the measured values in the standard mapping apply to installations with the fol-
lowing nominal operating values:
Measurement: Full Scale Voltage (parameter address 1103):
−>100 ... 1000 kV
Measurement: Full Scale Current (parameter address 1104):
−>10 ... 1000 A
Product of:
• Transformers – Rated Primary Voltage (parameter address 0203)
−>100 ... 1000 kV
Product of:
• Transformers– CT Rated primary current (parameter address 0205) and
• Ratio factor I4/Iph (parameter address 0221)
• >10 ... 1000 A
Power values:
• Product of Full Scale Voltage and Full Scale Current multiplied by √3
−>100 ... 1000 MW (MVAR)
Note
Depending on the device composition not all of the indicated analog inputs (and corresponding DNP message
points) may be available in the SIPROTEC device.
Note
Changes of the scaling of the measured values are possible in adaptation to the concrete installation environ-
ment (refer to manual “DNP 3.0 Communication Database”).

1 Notes to SIPROTEC objects
1.4 Metered measurands
13SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
1.4 Metered measurands
Scaling
The scaling of the metered measurands, which are derived from measured values, refers to:
60000 impulses per hour for V = Vprim and I = Iprim
Vprim =Full Scale Voltage
(parameter address = 1103)
Iprim =FULL SCALE CURRENT
parameter address = 1104)
Example
In the parameter set is configured:
Iprim = 1000 A and Vprim = 400.0 kV,
60000 impulses correspond so that:
1 h * 1000 A * 400 kV * √3 = 692.82 MWh
Note
• The type of the update (cyclic, with or without deletion) and the update interval must be pro-
grammed for the metered measurands with the parametrization software DIGSI 4.
• The scaling of the metered measurands at binary inputs ("Wp(puls)" and "Wq(puls)")
depends on the externally connected pulse generator.

1 Notes to SIPROTEC objects
1.4 Metered measurands
14 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011

15SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
DNP V3.0 Device Profile 2
2.1 Implementation Table 2-16
2.2 Device Profile Document 2-18

DNP V3.0 Device Profile
2.1 Implementation Table
16 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
2.1 Implementation Table
The following table gives a list of all objects recognized and returned by the SIPROTEC device.
For static objects, requests sent with qualifiers 00, 01, 06, 07 or 08 will be responded with
qualifiers 00 or 01.
Requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28.
For change-event objects, qualifiers17 or 28 are always responded.
In the table below text colored as 00, 01 (start stop) indicates Subset Level 3 functionality
(beyond Subset Level 2), text colored as 07, 08 (limited qty) indicates functionality beyond
Subset Level 3.
OBJECTS REQUEST RESPONSE
Object Vari-
ation
Description Function
Codes
(dec)
Qualifier Codes
(hex)
Function
Codes (dec)
Qualifier Codes
(hex)
1 0 Binary Input -
Any Variations
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
1 2 Binary Input with Status 1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
2 0 Binary Input Change -
Any Variations
1(read) 06 (no range)
07, 08 (limited qfy)
2 2 Binary Input Change
with Time
1(read) 06 (no range)
07, 08 (limited qfy)
129 (response)
130 (unsol. resp)
17, 28 (index)
10 0 Binary Output -
Any Variations
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
10 2 Binary Output with
Status
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
12 1 Contol Relay Output
Block
3(select)
4(operate)
5(direct op.)
6(dir. op. noack)
00, 01 (start-stop)
07, 08 (limited qfy)
17, 28 (index)
129 (response) echo of response
20 0 Binary Counter -
Any Variations
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
20 1 32-Bit Binary Counter
(with Flag)
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
22 0 Counter Change Event
- Any Variations
1(read) 06 (no range)
07, 08 (limited qfy)
22 1 32-Bit Counter Change
Event without Time
1(read) 06 (no range)
07, 08 (limited qfy)

DNP V3.0 Device Profile
2.1 Implementation Table
17SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
30 0 16-Bit Analog Input -
Any Variations
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
30 1 32-Bit Analog Input with
Status
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
30 2 16-Bit Analog Input with
Status
1(read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129 (response) 00, 01 (start-stop)
17, 28 (index)
32 0 Analog Change Event -
Any Variations
1(read) 06 (no range)
07, 08 (limited qfy)
32 1 32-Bit Analog Change
Event without Time
1(read) 06 (no range)
07, 08 (limited qfy)
129 (response)
130 (unsol. resp)
17, 28 (index)
32 2 16-Bit Analog Change
Event without Time
1(read) 06 (no range)
07, 08 (limited qfy)
129 (response)
130 (unsol. resp)
17, 28 (index)
50 1 Time and Date 2(write) 07 (limited qfy = 1)
60 1 Class 0 Data 1(read) 06 (no range)
60 2 Class 1 Data 1(read) 06 (no range)
07, 08 (limited qfy)
60 3 Class 2 Data 1(read) 06 (no range)
07, 08 (limited qfy)
60 4 Class 3 Data 1(read) 06 (no range)
07, 08 (limited qfy)
80 1 Internal Indications 2(write) 00 (start-stop)
(index must = 7)
OBJECTS REQUEST RESPONSE
Object Vari-
ation
Description Function
Codes
(dec)
Qualifier Codes
(hex)
Function
Codes (dec)
Qualifier Codes
(hex)

DNP V3.0 Device Profile
2.2 Device Profile Document
18 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
2.2 Device Profile Document
DNP V3.0
DEVICE PROFILE DOCUMENT
Vendor Name: SIEMENS AG
Device Name: 7SD80
Highest DNP Level Supported:
For Requests DNP-L2
For Responses DNP-L2
Device Function:
Master Slave
Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP Levels Supported (the
complete list is described in the attached table):
For static (non-change-event) object requests, request qualifier codes 00 and 01 (start-stop), 07 and 08
(limited quantity), and 17 and 28 (index) are supported in addition to request qualifier code 06 (no range).
Static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01.
Static object requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28. For change-
event object requests, qualifiers 17 or 28 are always responded.
16-bit Analog Change Events with Time may be requested.
The write function code for Object 50 (Time and Date), variation 1, is supported.
The features outlined within this Device Profile have successfully passed DNP Conformance Test of Subset
Level 2 outlined in DNP3-2000 IED Certification Procedure.
Maximum Data Link Frame Size (octets):
Transmitted____292_____________
Received______292_____________
Maximum Application Fragment Size (octets):
Transmitted _Configurable up to 2048
Received_______2048_______
Maximum Data Link Re-tries:
None
Fixed at
Configurable, range 0 to 255
Maximum Application Layer Re-tries:
None
Configurable, range ____ to _______
(Fixed is not permitted)
Requires Data Link Layer Confirmation:
Never
Always
Sometimes If 'Sometimes', when? ______________________________________
Configurable If 'Configurable', how? by the protection data processing program DIGSI 4
Requires Application Layer Confirmation:
Never
Always (not recommended)
When reporting Event Data (Slave devices only)
When sending multi-fragment responses (Slave devices only)
Sometimes If 'Sometimes', when? ___________________________________
Configurable If 'Configurable', how? by the protection data processing program DIGSI 4

DNP V3.0 Device Profile
2.2 Device Profile Document
19SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Requires Application Layer Confirmation:
Never
Always (not recommended)
When reporting Event Data (Slave devices only)
When sending multi-fragment responses (Slave devices only)
Sometimes If 'Sometimes', when? ___________________________________
Configurable If 'Configurable', how? by the protection data processing program DIGSI 4
Timeouts while waiting for:
Data Link Confirm None Fixed at _____ Variable Configurable
Complete Appl. Fragment None Fixed at _____ Variable Configurable
Application Confirm None Fixed at _____ Variable Configurable
Complete Appl. Response None Fixed at _____ Variable Configurable
Others: Default value are configurable by the protection data processing program DIGSI 4
Sends/Executes Control Operations:
WRITE Binary Outputs Never Always Sometimes Configurable
SELECT/OPERATE Never Always Sometimes Configurable
DIRECT OPERATE Never Always Sometimes Configurable
DIRECT OPERATE - NO ACK Never Always Sometimes Configurable
Count > 1 Never Always Sometimes Configurable
Pulse On Never Always Sometimes Configurable
Pulse Off Never Always Sometimes Configurable
Latch On Never Always Sometimes Configurable
Latch Off Never Always Sometimes Configurable
Queue Never Always Sometimes Configurable
Clear Queue Never Always Sometimes Configurable
Note:
CONTROL RELAY OUTPUT BLOCK parameters (count, on-time, off-time) are ignored.
TimeSync Information:
a.) TimeSync Period
Never
Fixed at ________seconds
Configurable, range ____1____to __86400_seconds
b.) Maximum time base drift over 10 minute interval: ____30__ms
c.) Maximum Internal Time Reference Error when set via DNP: _____1__ms
d.) Maximum Delay Measurement error: ____20__ms
e.) Maximum response time: ___100__ms
c.) Event data time-tag error – if different than (c):
Binary Input Change Events __________ms
Counter Change Events __________ms
Frozen Counter Change Events __________ms
Analog Change Events __________ms
Frozen Analog Change Events __________ms

DNP V3.0 Device Profile
2.2 Device Profile Document
20 SIPROTEC, 7SD80, Bus mapping DNP 3.0
C53000-L2040-C347-1, Edition 07.2011
Reports Binary Input Change Events when no
specific variation requested:
Never
Only time-tagged
Only non-time-tagged
Configurable to send both, one or the
other (attach explanation)
Reports time-tagged Binary Input Change Events
when no specific variation requested:
Never
Binary Input Change With Time
Binary Input Change With Relative
Time
Configurable (attach explanation)
Sends Unsolicited Responses:
Never
Configurable (Unsolicited data
response mode are switched
on/off via the configuration tool )
Only certain objects
Sometimes (attach explanation)
ENABLE/DISABLE UNSOLICITED
Function codes supported
Sends Static Data in Unsolicited Responses:
Never
When Device Restarts
When Status Flags Change
No other options are permitted.
Default Counter Object/Variation:
No Counters Reported
Configurable (attach explanation)
Default Object ___20_____
Default Variation ___01_____
Point-by-point list attached
Sends 32-Bit counters.
Counters Roll Over at:
No Counters Reported
Configurable (attach explanation)
16 Bits
32 Bits
Other Value _____________
Point-by-point list attached
Sends Multi-Fragment Responses: Yes No