Siemens SIMATIC NET RUGGEDCOM RSG2488F User manual

Edition 11/2019
Installation Manual
SIMATIC NET
Industrial Ethernet Switches
RUGGEDCOM RSG2488F
https://www.siemens.com

SIMATIC NET
Industrial Ethernet Switches
RUGGEDCOM RSG2488F
Installation Manual
Preface
Introduction 1
Installing the Device 2
Device Management 3
Modules 4
Technical Specifications 5
Certification 6
11/2019
C79000-G8976-1351-05

Legal Information
Warning Notice System
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown be-
low are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger
will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relat-
ing to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the
specific task in accordance with the relevant documentation, in particular its warning notices and safety in-
structions. Qualified personnel are those who, based on their training and experience, are capable of identify-
ing risks and avoiding potential hazards when working with these products/systems.
Proper Use of Siemens Products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommend-
ed or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permis-
sible ambient conditions must be complied with. The information in the relevant documentation must be ob-
served.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publica-
tion may be trademarks whose use by third parties for their own purposes could violate the rights of the own-
er.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software de-
scribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the in-
formation in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Digital Industry
Process Automation
Postfach 48 48
90026 NÜRNBERG
GERMANY
© 11/2019 Subject to Change Copyright © Siemens 2019
All rights reserved

Table of Contents
Preface ............................................................................................................................................ v
Related Documents ................................................................................................................. v
Accessing Documentation ....................................................................................................... v
Training ................................................................................................................................... v
Customer Support .................................................................................................................. vi
Contacting Siemens ................................................................................................................ vi
1 Introduction ........................................................................................................................... 1
1.1 Feature Highlights ................................................................................................. 1
1.2 Description ............................................................................................................ 2
1.3 Required Tools and Materials ................................................................................. 3
1.4 Tamper-Evident Security Seals ............................................................................... 3
1.5 Cabling Recommendations .................................................................................... 4
1.5.1 Protection On Twisted-Pair Data Ports .................................................................... 4
1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations ...................................... 4
1.5.3 Supported Fiber Optic Cables ................................................................................ 5
1.6 Decommissioning and Disposal ............................................................................. 5
2 Installing the Device ............................................................................................................. 7
2.1 General Procedure ................................................................................................. 7
2.2 Unpacking the Device ........................................................................................... 8
2.3 Mounting the Device ............................................................................................. 8
2.3.1 Mounting the Device to a Rack .............................................................................. 9
2.3.2 Mounting the Device on a DIN Rail ........................................................................ 9
2.3.3 Mounting the Device to a Panel .......................................................................... 10
2.4 Connecting the Failsafe Alarm Relay .................................................................... 11
2.5 Connecting Power ............................................................................................... 12
2.5.1 Connecting High AC/DC Power ............................................................................ 13
2.5.2 Connecting Low DC Power .................................................................................. 14
2.5.3 Grounding the Device ......................................................................................... 15
2.5.4 Wiring Examples .................................................................................................. 16
3 Device Management ........................................................................................................... 19
3.1 Connecting to the Device .................................................................................... 19
3.2 Configuring the Device ........................................................................................ 20
3.3 Inserting/Removing the MicroSD Card .................................................................. 20
4 Modules ............................................................................................................................... 23
4.1 Available Modules ............................................................................................... 24
4.2 Installing/Removing Line Modules ........................................................................ 31
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 iii

Table of Contents
4.3 Installing/Removing Power Modules .................................................................... 33
5 Technical Specifications ...................................................................................................... 37
5.1 Power Supply Specifications ................................................................................ 37
5.2 Failsafe Alarm Relay Specifications ...................................................................... 37
5.3 Supported Networking Standards ........................................................................ 38
5.4 Operating Environment ....................................................................................... 38
5.5 Mechanical Specifications .................................................................................... 38
5.6 Dimension Drawings ........................................................................................... 38
6 Certification ......................................................................................................................... 43
6.1 Approvals ............................................................................................................ 43
6.1.1 TÜV SÜD ............................................................................................................. 43
6.1.2 European Union (EU) .......................................................................................... 43
6.1.3 FCC ..................................................................................................................... 44
6.1.4 ISED .................................................................................................................... 44
6.1.5 RoHS ................................................................................................................... 44
6.1.6 Other Approvals .................................................................................................. 45
6.2 EMC and Environmental Type Tests ..................................................................... 45
iv RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Preface
This guide describes the RUGGEDCOM RSG2488F. It describes the major features of
the device, installation, commissioning and important technical specifications.
It is intended for use by network technical support personnel who are responsible
for the installation, commissioning and maintenance of the device. It is also recom-
mended for use by network and system planners, system programmers, and line
technicians.
Related Documents
Other documents that may be of interest include:
•RUGGEDCOM RSG2488F User Guide [https://support.industry.siemens.com/cs/-
ww/en/view/109757150]
•RUGGEDCOM RSG2488F Series Modules Catalog [https://support.indus-
try.siemens.com/cs/ww/en/view/109757282]
Accessing Documentation
The latest user documentation for RUGGEDCOM RSG2488F is available online at
https://www.siemens.com. To request or inquire about a user document, contact
Siemens Customer Support.
Training
Siemens offers a wide range of educational services ranging from in-house training
of standard courses on networking, Ethernet switches and routers, to on-site cus-
tomized courses tailored to the customer's needs, experience and application.
Siemens' Educational Services team thrives on providing our customers with the es-
sential practical skills to make sure users have the right knowledge and expertise to
understand the various technologies associated with critical communications net-
work infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain
knowledge in the utility, transportation and industrial markets, allows Siemens to
provide training specific to the customer's application.
For more information about training services and course availability, visit https://-
www.siemens.com or contact a Siemens Sales representative.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 v

Preface
Customer Support
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers.
For technical support or general information, contact Siemens Customer Support
through any of the following methods:
Online
Visit http://www.siemens.com/automation/support-request to submit a
Support Request (SR) or check on the status of an existing SR.
Telephone
Call a local hotline center to submit a Support Request (SR). To locate a lo-
cal hotline center, visit https://w3.siemens.com/aspa_app/?lang=en.
Mobile App
Install the Industry Online Support app by Siemens AG on any Android,
Apple iOS or Windows mobile device and be able to:
• Access Siemens' extensive library of support documentation, includ-
ing FAQs and manuals
• Submit SRs or check on the status of an existing SR
• Contact a local Siemens representative from Sales, Technical Support,
Training, etc.
• Ask questions or share knowledge with fellow Siemens customers
and the support community
Contacting Siemens
Address
Siemens AG
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Telephone
Toll-free: 1 888 264 0006
Tel: [phone]
Fax: [phone]
E-mail
ruggedcom.info.i-i
[email protected]
Web
https://www.siemens.com
vi RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Introduction 1
The RUGGEDCOM RSG2488F is a utility grade, fully managed, industrial Ethernet
switch designed to operate reliably in harsh environments. With a rugged metal en-
closure and an optional conformal coating, the RUGGEDCOM RSG2488F provides a
high level of immunity to electromagnetic interference and heavy electrical surges,
and can withstand temperatures between -40 and 85 °C (-40 and 185 °F).
Highly modular, the RUGGEDCOM RSG2488F switch supports up to 28 electrical and/
or optical interfaces with data transfer rates of 10/100/1000 Mbit/s. This makes it the
ideal industry-standard switch for constructing electrical and/or optical line, ring and
star topologies.
1.1 Feature Highlights
Extreme Flexibility
• Support for up to a total of 28 non-blocking ports (six 4-port modules and two 2-
port modules)
• Mixture of fiber optic or copper Gigabit ports with up to 28 Gig Ethernet ports
• All-aluminum construction
Compact 1U Form Factor
• Space-saving design
Vertical Loading Modular Design
• Allows for simple, cost effective in-field servicing and upgrading
Dual Redundant Smart Power Supplies
• Hot-swappable, cable-free
• HI voltage AC/DC: 100-300 V DC or 88-264 V AC
• Smart power supplies able to detect loss of input voltage
Fast Network Fault Recovery
• Less than 5 ms per hop (typical)
Reliability in Harsh Environments
• Immunity to EMI and heavy electrical surges
• Zero-Packet-Loss Technology
• Supports Siemens FastConnect RJ-45 Cabling System
• -40 to 85 °C (-40 to 185 °F) operating temperature (fan-less)
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 1

Introduction
1.2Description
• Conformal coated printed circuit boards (optional)
1.2 Description
The RUGGEDCOM RSG2488F features various ports, controls and indicator LEDs on
the front panel for connecting, configuring and troubleshooting the device.
5
1
8
2
3
6
7
9
11
12
11
4
4
10
1 Front
2 Rear
3 Power Modules
4 Power Status LEDs
5 RS-232 Serial Console Port (DB9)
6 Management Port
7 Alarm Indicator LED
8 Access Plate
9 Port Status LEDs
10 Line Modules
11 Power Supply Terminal Block
12 Chassis Ground Terminal
Figure1.1 RUGGEDCOM RSG2488F
Power Status LEDs Indicates the status of the power modules.
LED Description
I The power module is receiving power
O The power module is supplying power
RS-232 Console Port The serial console port is for interfacing directly with the device and
accessing initial management functions. For information about con-
necting to the device via the serial console port, refer to "Connect-
ing to the Device (Page 19)".
Management Port The 10/100Base-T Ethernet management port is for system man-
agement that is out-of-band from the switch fabric. For information
about connecting to the device via the 10/100Base-T Ethernet man-
agement port, refer to "Connecting to the Device (Page 19)".
Alarm Indicator LED The alarm indicator LED illuminates when an alarm condition exists.
2RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Introduction
1.3Required Tools and Materials
Access Plate The removable access plate provides access to the microSD slot. Use
a microSD card to load/store the firmware and configuration for the
device. For information about using a microSD card, refer to "Insert-
ing/Removing the MicroSD Card (Page 20)".
Port Status LEDs Port status indicator LEDs indicate the operational status of each
port.
State Description
Solid Link detected
Blinking Link activity
Off No link detected
Line Modules The device features slots for up to eight line modules. For more in-
formation, refer to "Modules (Page 23)".
Failsafe Alarm Relay Latches to default state when a power disruption or other alarm
condition occurs. For more information, refer to:
•"Connecting the Failsafe Alarm Relay (Page 11)"
•"Failsafe Alarm Relay Specifications (Page 37)"
Power Supply Terminal Block A pluggable terminal block. For more information, refer to:
•"Connecting Power (Page 12)"
•"Power Supply Specifications (Page 37)"
Chassis Ground Terminal Protects the device from power surges and accumulated static
electricity. For information about grounding the device, refer to
"Grounding the Device (Page 15)".
1.3 Required Tools and Materials
The following tools and materials are required to install the RUGGEDCOM RSG2488F:
Tools/Materials Purpose
AC/DC power cord (16 AWG) For connecting power to the device.
Lightning protector For protecting the device from harmful electrical
strikes.
Shielded coaxial cables For connecting the device to antennas and an Eth-
ernet network.
Flathead screwdriver For mounting the device to a DIN rail.
Phillips screwdriver For mounting the device to a panel.
4 x #6-32 screws For mounting the device to a panel.
Braided or equivalent ground wire For grounding the device to safety Earth.
1.4 Tamper-Evident Security Seals
In compliance with the security requirements of the Federal Information Processing
Standards (FIPS140-2), FIPS-compliant tamper-evident security seals are applied to
potential access points on this device. Security seals provide evidence of unautho-
rized tampering or removal of components.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 3

Introduction
1.5Cabling Recommendations
NOTICE
Worn, damaged or missing seals must be replaced immediately.
Replacement seals are available for purchase from Siemens. For more information,
contact a Siemens Sales representative.
There are three ways to determine if a security seal has been tampered with:
• The seal is cut or torn
• A pattern is left on the device when the top layer of the seal is removed
• Residue left by the seal is visible on the device under ultra-violet light
For information about the placement of security seals, refer to the RUGGEDCOM
RUGGEDCOM RSG2488F FIPS 140-2 Non-Proprietary Security Policy [https://sup-
port.industry.siemens.com/cs/ww/en/view/109757984] .
1.5 Cabling Recommendations
Siemens recommends using SIMATIC NET industrial Ethernet shielded cables for all
Ethernet ports.
1.5.1 Protection On Twisted-Pair Data Ports
All copper Ethernet ports on RUGGEDCOM products include transient suppression
circuitry to protect against damage from electrical transients and conform with IEC
61850-3 and IEEE 1613 Class 1 standards. This means that during a transient electri-
cal event, communications errors or interruptions may occur, but recovery is auto-
matic.
Siemens also does not recommend using copper Ethernet ports to interface with de-
vices in the field across distances that could produce high levels of ground potential
rise (i.e. greater than 2500 V), during line-to-ground fault conditions.
1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations
The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet commu-
nications over distances of up to 100 m (328 ft) using all 4 pairs in category 5 (or
higher) balanced, unshielded twisted-pair cabling. For wiring guidelines, system de-
signers and integrators should refer to the Telecommunications Industry Association
(TIA) TIA/EIA-568-A wiring standard that characterizes minimum cabling performance
specifications required for proper Gigabit Ethernet operation. For reliable, error-free
data communication, new and pre-existing communication paths should be verified
for TIA/EIA-568-A compliance.
4RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Introduction
1.5.3Supported Fiber Optic Cables
The following table summarizes the relevant cabling standards:
Cabling
Category
1000Base-
TX Compliant Required Action
< 5 No New wiring infrastructure required.
5 Yes Verify TIA/EIA-568-A compliance.
5e Yes No action required. New installations should be designed with Cate-
gory 5e or higher.
6 Yes No action required.
> 6 Yes Connector and wiring standards to be determined.
Follow these recommendations for copper data cabling in high electrical noise envi-
ronments:
• Data cable lengths should be as short as possible, preferably 3 m (10 ft) in
length. Copper data cables should not be used for inter-building communica-
tions.
• Power and data cables should not be run in parallel for long distances, and
should be installed in separate conduits. Power and data cables should intersect
at 90° angles when necessary to reduce inductive coupling.
• Shielded/screened cabling can be used when required. Care should be taken to
avoid the creation of ground loops with shielded cabling.
1.5.3 Supported Fiber Optic Cables
The following fiber optic cable types are supported under the stated conditions.
Distance (m)Cable Type Wavelength (nm) Modal Band-
width (MHz·km) 100Base-FX 1000Base-SX 10GBase-SR
850 200 — 275 33OM1 (62.5/125)
1300 500 2000 — —
850 500 — 550 82OM2 (50/125)
1300 500 2000 — —
850 1500 — 550 300OM3 (50/125)a
1300 500 2000 — —
850 3500 — 550 400OM4 (50/125)a
1300 500 2000 — —
aLaser optimized.
1.6 Decommissioning and Disposal
Proper decommissioning and disposal of this device is important to prevent malicious
users from obtaining proprietary information and to protect the environment.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 5

Introduction
1.6Decommissioning and Disposal
Decommissioning
This device may include sensitive, proprietary data. Before taking the device out of
service, either permanently or for maintenance by a third-party, make sure it has
been fully decommissioned.
For more information, refer to the associated User Guide.
Recycling and Disposal
For environmentally friendly recycling and disposal of this device and related acces-
sories, contact a facility certified to dispose of waste electrical and electronic equip-
ment. Recycling and disposal must be done in accordance with local regulations.
6RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Installing the Device 2
This chapter describes how to install the device, including mounting the device, con-
necting power, and connecting the device to the network.
DANGER
Electrocution hazard – risk of serious personal injury and/or damage to equip-
ment
Before performing any maintenance tasks, make sure all power to the device has
been disconnected and wait approximately two minutes for any remaining energy
to dissipate.
WARNING
Radiation hazard – risk of serious personal injury
This product may contain a laser system and is classified as a CLASS 1 LASER PROD-
UCT. Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure
NOTICE
This product contains no user-serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate
specifications, test results, and agency approvals, and void the user's authority to
operate the equipment.
NOTICE
This product should be installed in a restricted access location where access can only
be gained by authorized personnel who have been informed of the restrictions and
any precautions that must be taken. Access must only be possible through the use of
a tool, lock and key, or other means of security, and controlled by the authority re-
sponsible for the location.
2.1 General Procedure
The general procedure for installing the device is as follows:
NOTICE
The user is responsible for the operating environment of the device, including main-
taining the integrity of all protective conductor connections and checking equip-
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 7

Installing the Device
2.2Unpacking the Device
ment ratings. Make sure to review all operating and installation instructions before
commissioning or performing maintenance on the device.
1. Review the relevant certification information for any regulatory requirements.
For more information, refer to "Approvals (Page 43)".
2. Review the RUGGEDCOM RSG2488F Modules Catalog for special installation or
regulatory requirements related to the modules installed in the device. In the
case of Precision Time Protocol (PTP) line modules, this includes antenna instal-
lation and regulatory requirements.
3. Mount the device.
4. Connect the failsafe alarm relay.
5. Connect power to the device and ground the device to safety Earth.
6. Connect the device to the network.
7. Configure the device.
2.2 Unpacking the Device
When unpacking the device, do the following:
1. Inspect the package for damage before opening it.
2. Visually inspect each item in the package for any physical damage.
3. Verify all items are included.
NOTICE
If any item is missing or damaged, contact Siemens for assistance.
2.3 Mounting the Device
The RUGGEDCOM RSG2488F is designed for maximum mounting and display flexibili-
ty. It can be ordered with adapters that allow it to be installed in a 48 cm (19 in) rack,
35 mm (1.4 in) DIN rail, or directly on a panel.
NOTICE
Heat generated by the device is channeled outwards from the enclosure. As such, it
is recommended that 2.5 cm (1 in) of space be maintained on all open sides of the
device to allow for some convectional airflow.
Forced airflow is not required. However, any increase in airflow will result in a reduc-
tion of ambient temperature and improve the long-term reliability of all equipment
mounted in the rack space.
8RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Installing the Device
2.3.1Mounting the Device to a Rack
Note
For detailed dimensions of the device with either rack, DIN rail or panel hardware in-
stalled, refer to "Dimension Drawings (Page 38)".
2.3.1 Mounting the Device to a Rack
For rack mount installations, the RUGGEDCOM RSG2488F can be ordered with rack
mount adapters pre-installed at the front and rear of the chassis. Additional adapters
are provided to further secure the device in high-vibration or seismically active loca-
tions.
To secure the device to a standard 48 cm (19 in) rack, do the following:
1. Make sure the front and rear rack mount adapters are installed on the both sides
of the chassis.
Note
The chassis features multiple mounting holes, allowing the rack mount adapters
to be installed up to 25 mm (1 in) from the face of the device.
33
21
1 Rear
2 Front
3 Rack Mount Adapter
Figure2.1 Rack Mount Adapters
2. Insert the device into the rack. To make the modules and ports accessible from
the front, insert the power supply side of the device first. Reverse the orienta-
tion to have the power supplies, management ports and LEDs accessible from
the front.
3. Secure the adapters to the rack using the supplied hardware.
2.3.2 Mounting the Device on a DIN Rail
For DIN rail installations, the RUGGEDCOM RSG2488F can be ordered with panel/DIN
rail adapters pre-installed on each side of the chassis. The adapters allow the device
to be slid onto a standard 35 mm (1.4 in) DIN rail.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 9

Installing the Device
2.3.3Mounting the Device to a Panel
To mount the device to a DIN rail, do the following:
1. Align the adapters with the DIN rails and slide the device into place.
3
1
1
2
2
1 DIN Rail
2 Panel/DIN Rail Adaptor
3 Screw
Figure2.2 DIN Rail Mounting
2. Install one of the supplied screws on either side of the device to secure the
adapters to the DIN rails.
2.3.3 Mounting the Device to a Panel
For panel installations, the RUGGEDCOM RSG2488F can be ordered with panel/DIN
rail adapters pre-installed on each side of the chassis. The adapters allow the device
to be attached to a panel using screws.
10 RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Installing the Device
2.4Connecting the Failsafe Alarm Relay
To mount the device to a panel, do the following:
1. Place the device against the panel and align the adapters with the mounting
holes.
2
1
1
1 Screw
2 Panel/DIN Rail Adaptor
Figure2.3 Panel Mounting
2. Install the supplied screws to secure the adapters to the panel.
2.4 Connecting the Failsafe Alarm Relay
The failsafe relay can be configured to latch based on alarm conditions. The NO
(Normally Open) contact is closed when the unit is powered and there are no ac-
tive alarms. If the device is not powered or if an active alarm is configured, the relay
opens the NO contact and closes the NC (Normally Closed) contact.
Note
Control of the failsafe relay output is configurable through RUGGEDCOM RSG2488F.
One common application for this relay is to signal an alarm if a power failure oc-
curs. For more information, refer to the RUGGEDCOM RSG2488F User Guide for the
RUGGEDCOM RSG2488F.
The following shows the proper relay connections.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 11

Installing the Device
2.5Connecting Power
3
5
4
3
5
4
2
1
1 Pluggable Terminal Block for HI Power Supplies
2 Screw-Type Terminal Block for HIP Power Supplies
3 Normally Open Terminal
4 Common Terminal
5 Normally Closed Terminal
Figure2.4 Failsafe Alarm Relay Wiring
2.5 Connecting Power
The RUGGEDCOM RSG2488F supports dual redundant AC and/or DC power supplies
that can be installed in any combination.
The RUGGEDCOM RSG2488F can be equipped with either a screw-type or pluggable
terminal block, which provides power to both power supplies. The screw-type ter-
minal block is installed using Phillips screws and compression plates, allowing either
bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reli-
able connections under severe shock or vibration.
DANGER
Electrocution hazard – risk of serious personal injury or death
The device may have two power supplies equipped, which may be connected to sep-
arate power sources. Make sure all power sources are off before servicing the power
supply terminals.
CAUTION
Electrical hazard – risk of damage to equipment
Do not connect wiring to unused power supply input terminals. For instance, if a
Low DC power supply is installed in the PS1 slot, do not connect the PS1 High AC/DC
terminals to a power source.
NOTICE
• In a high AC/DC and low DC (24/48 V) power supply arrangement, the place-
ment of the AC and DC power supplies is not slot-dependent. However, if a high
AC/DC power supply is installed in slot PS1, the high AC/DC wiring must be con-
nected to the high terminal block PS1 terminals. If a low DC power supply is in-
stalled in slot PS1, the low DC wiring must be made to the low terminal block
12 RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05

Installing the Device
2.5.1Connecting High AC/DC Power
PS1 terminals. High voltage wiring is always made to the upper Hi terminal
block and low voltage (24/48 V) wiring is always made to the lower Lo terminal
block.
• Use minimum #16 gage wiring when connecting terminal blocks.
• The maximum wire length between the terminal block and power source must
not exceed 6 m (20 ft) for 24 V power supplies or 18 m (60 ft) for 48 V power
supplies.
• A circuit breaker rated no higher than 20 A must be installed between the device
and the supply mains.
• Whenever possible, use a separate circuit breaker for each power supply.
• For maximum redundancy in a dual power supply configuration, use two inde-
pendent power sources.
• A socket outlet/disconnect device must be installed near the device and be easily
accessible.
• Equipment must be installed according to applicable local wiring codes and
standards.
2.5.1 Connecting High AC/DC Power
To connect a high AC/DC power supply to the device, do the following:
DANGER
Electrocution hazard – risk of death, serious personal injury and/or damage to
the device
Make sure the supplied cover is always installed over high voltage screw-type termi-
nal blocks.
CAUTION
Electrical hazard – risk of damage to equipment
Do not connect AC power cables to a DC power supply terminal block. Damage to
the power supply may occur.
Note
The screw-type terminal block is installed using Phillips screws and compression
plates, allowing either bare wire connections or crimped terminal lugs. Use #6 size
ring lugs for secure, reliable screws, which must be removed to make connections.
RUGGEDCOM RSG2488F
Installation Manual, 11/2019, C79000-G8976-1351-05 13