Siemens SIMATIC NET User manual

Edition 04/2021
Installation Manual
SIMATIC NET
Rugged Ethernet Switches
RUGGEDCOM RMC30
https://www.siemens.com

SIMATIC NET
Rugged Ethernet Switches
RUGGEDCOM RMC30
Installation Manual
Preface
Introduction 1
Installing the Device 2
Device Management 3
Communication Ports 4
Technical Specifications 5
Certification 6
04/2021
C79000-G8976-1008-10

Legal Information
Warning Notice System
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown
below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger
will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning
relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the
specific task in accordance with the relevant documentation, in particular its warning notices and safety
instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper Use of Siemens Products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant
technical documentation. If products and components from other manufacturers are used, these must be
recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning,
operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant
documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Digital Industry
Process Automation
Postfach 48 48
90026 NÜRNBERG
GERMANY
© 04/2021 Subject to Change Copyright © Siemens 2021
All rights reserved

Table of Contents
Preface ............................................................................................................................................ v
Related Documents ................................................................................................................. v
Accessing Documentation ....................................................................................................... v
Registered Trademarks ............................................................................................................ v
Warranty ................................................................................................................................. v
Training .................................................................................................................................. vi
Customer Support .................................................................................................................. vi
Contacting Siemens ............................................................................................................... vii
1 Introduction ........................................................................................................................... 1
1.1 Feature Highlights ................................................................................................. 1
1.2 Description ............................................................................................................ 2
1.3 Required Tools and Materials ................................................................................. 3
1.4 Decommissioning and Disposal ............................................................................. 3
2 Installing the Device ............................................................................................................. 5
2.1 General Procedure ................................................................................................. 6
2.2 Unpacking the Device ........................................................................................... 6
2.3 Mounting the Device ............................................................................................. 6
2.3.1 Mounting the Device on a DIN Rail ........................................................................ 7
2.3.2 Mounting the Device to a Panel ............................................................................ 9
2.4 Connecting Power ................................................................................................. 9
2.4.1 Connecting AC Power .......................................................................................... 10
2.4.2 Connecting DC Power ......................................................................................... 12
3 Device Management ........................................................................................................... 13
3.1 Connecting to the Device .................................................................................... 13
3.2 Configuring the Device ........................................................................................ 13
3.3 Resetting the Device ........................................................................................... 14
4 Communication Ports .......................................................................................................... 15
4.1 Copper Ethernet Port ........................................................................................... 15
4.2 Serial Terminal .................................................................................................... 17
4.2.1 RS232 Data Ports ................................................................................................ 17
4.2.2 RS485/422 Data Ports .......................................................................................... 18
5 Technical Specifications ...................................................................................................... 21
5.1 Power Supply Specifications ................................................................................ 21
5.2 Copper Ethernet Port Specifications ..................................................................... 21
5.3 Supported Networking Standards ........................................................................ 21
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 iii

Table of Contents
5.4 Operating Environment ....................................................................................... 22
5.5 Mechanical Specifications .................................................................................... 22
5.6 Dimension Drawings ........................................................................................... 22
6 Certification ......................................................................................................................... 25
6.1 Approvals ............................................................................................................ 25
6.1.1 CSA ..................................................................................................................... 25
6.1.2 European Union (EU) .......................................................................................... 25
6.1.3 FCC ..................................................................................................................... 26
6.1.4 FDA/CDRH ........................................................................................................... 26
6.1.5 ISED .................................................................................................................... 26
6.1.6 ISO ...................................................................................................................... 26
6.1.7 ACMA .................................................................................................................. 27
6.1.8 RoHS ................................................................................................................... 27
6.1.9 Other Approvals .................................................................................................. 27
6.2 EMC and Environmental Type Tests ..................................................................... 28
iv RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Preface
This guide describes the RUGGEDCOM RMC30. It describes the major features of the
device, installation, commissioning and important technical specifications.
It is intended for use by network technical support personnel who are responsible
for the installation, commissioning and maintenance of the device. It is also
recommended for use by network and system planners, system programmers, and
line technicians.
Related Documents
Other documents that may be of interest include:
Document Title Link
RUGGEDCOM ROS Configuration Manual https://support.industry.siemens.com/cs/ww/en/
view/109737240
Accessing Documentation
The latest user documentation for RUGGEDCOM RMC30 is available online at https://
support.industry.siemens.com . To request or inquire about a user document,
contact Siemens Customer Support.
Registered Trademarks
RUGGEDCOM ™ and ROS™ are trademarks of Siemens AG.
Other designations in this manual might be trademarks whose use by third parties
for their own purposes would infringe the rights of the owner.
Warranty
Siemens warrants this product for a period of five (5) years from the date of
purchase, conditional upon the return to factory for maintenance during the
warranty term. This product contains no user-serviceable parts. Attempted service by
unauthorized personnel shall render all warranties null and void. The warranties set
forth in this article are exclusive and are in lieu of all other warranties, performance
guarantees and conditions whether written or oral, statutory, express or implied
(including all warranties and conditions of merchantability and fitness for a particular
purpose, and all warranties and conditions arising from course of dealing or usage
or trade). Correction of nonconformities in the manner and for the period of time
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 v

Preface
Training
provided above shall constitute the Seller’s sole liability and the Customer’s exclusive
remedy for defective or nonconforming goods or services whether claims of the
Customer are based in contract (including fundamental breach), in tort (including
negligence and strict liability) or otherwise.
For warranty details, visit https://www.siemens.com or contact a Siemens customer
service representative.
Training
Siemens offers a wide range of educational services ranging from in-house training
of standard courses on networking, Ethernet switches and routers, to on-site
customized courses tailored to the customer's needs, experience and application.
Siemens' Educational Services team thrives on providing our customers with the
essential practical skills to make sure users have the right knowledge and expertise
to understand the various technologies associated with critical communications
network infrastructure technologies.
Siemens ' unique mix of IT/Telecommunications expertise combined with domain
knowledge in the utility, transportation and industrial markets, allows Siemens to
provide training specific to the customer's application.
For more information about training services and course availability, visit https://
www.siemens.com or contact a Siemens Sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers.
For technical support or general information, contact Siemens Customer Support
through any of the following methods:
Online
Visit http://www.siemens.com/automation/support-request to submit a
Support Request (SR) or check on the status of an existing SR.
Telephone
Call a local hotline center to submit a Support Request (SR). To locate a
local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en.
Mobile App
Install the Industry Online Support app by Siemens AG on any Android,
Apple iOS or Windows mobile device and be able to:
• Access Siemens' extensive library of support documentation,
including FAQs and manuals
• Submit SRs or check on the status of an existing SR
• Contact a local Siemens representative from Sales, Technical Support,
Training, etc.
vi RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Preface
Contacting Siemens
• Ask questions or share knowledge with fellow Siemens customers
and the support community
Contacting Siemens
Address Siemens AG
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Telephone Toll-free: 1 888 264 0006
Tel: [phone]
Fax: [phone]
E-Mail [email protected]
Web https://www.siemens.com
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 vii

Preface
Contacting Siemens
viii RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Introduction 1
The RUGGEDCOM RMC30 is an industrially hardened, 2-port Serial-to-Ethernet server
that has been specifically designed to operate in electrically harsh and climatically
demanding environments. The RUGGEDCOM RMC30 allows communication with
virtually any serial device via Ethernet, providing simple and reliable network
connectivity.
The RUGGEDCOM RMC30 is packaged in a compact, galvanized steel enclosure that
allows either DIN or panel mounting for efficient use of cabinet space. It has an
integrated power supply with a wide range of voltages for worldwide operability.
An operating temperature range of -40 to 85 °C (-40 to 185 °F) without the use of
internal cooling fans allows it to be placed in almost any location. The RUGGEDCOM
RMC30 is compliant with EMI and environmental standards for utility substations,
industrial manufacturing, process and control and intelligent transportation systems
applications.
The RUGGEDCOM RMC30 offers both an RS232 port and a RS485/422 port
simultaneously via a solid screw down terminal block. The 10Base-T Ethernet port
supports both auto-negotiation and auto-crossover detection and simplifies cabling.
Simple and intuitive network based configuration using either the built in Web or
Telnet server makes setup a breeze. The RUGGEDCOM RMC30’s superior ruggedized
design coupled with the Rugged Operating System™ (ROS®) provides improved
system reliability making it ideally suited for creating Ethernet networks for mission
critical, real-time, control applications.
1.1 Feature Highlights
Connectivity
• 1 x RS232 and 1 x RS422/485 port
• 1 x 10Base-TX port
• Fully compliant EIA/TIA RS485 and RS232 ports
• Built-In optional RS485 Termination
Serial Encapsulation
• Transmit serial data over an IP network
• Support for Modbus TCP, DNP 3, TIN serial protocols
• Baud rates up to 230 kbps
• Point to point and multi-point modes
• Convert Modbus RTU to Modbus TCP
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 1

Introduction
1.2Description
• Support multiple Modbus masters
• Use Serial IP port redirection software to support PC applications statistics and
built-in sniffer for troubleshooting
Designed for Harsh Environments
• Operates over a temperature range of -40 to 85 °C (-40 to 185 °F) without the
use of fans for improved reliability
• 21 AWG galvanized steel enclosure suitable for DIN or panel mounting provide
secure mechanical reliability
1.2 Description
The RUGGEDCOM RMC30 features various ports, controls and indicator LEDs on
the display panel for connecting, configuring and troubleshooting the device. The
display panel can be located on the rear, front or top of the device, depending on the
mounting configuration.
9
6
7
4 5
8
3
1
2
1 ALARM LED
2 POWER LED
3 Serial Terminal
4 Reset Button
5 Copper Ethernet Port with LEDs
6 RX LED
7 TX LED
8 Power Terminal Block
9 Chassis Ground Terminal
Figure1.1 RUGGEDCOM RMC30
ALARM LED Illuminates when an alarm condition exists.
POWER LED Illuminates when power is being supplied to the device.
2RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Introduction
1.3Required Tools and Materials
State Description
Green Power is on
Off Power is off
RESET Button Shuts down and restarts the device. For more information, refer to
"Resetting the Device (Page 14)".
TX/RX LEDs Indicate the connection status of the serial terminal.
LED State Description
TX Green
(Blinking)
Transmitting serial data
RX Green
(Blinking)
Receiving serial data
Serial Terminal The RS232/RS422/RS485 serial terminal serves a dual purpose:
• The RS232 terminals allow for a direct interface with the device
and access to initial management functions. For information
about connecting to the device via the serial terminal, refer to
"Connecting to the Device (Page 13)".
• The RS422/RS485 terminals allow for half or full duplex serial
connections respectively. For more information, refer to
"Communication Ports (Page 15)".
Power Supply Terminal A pluggable terminal. For more information, refer to:
•"Connecting Power (Page 9)"
•"Power Supply Specifications (Page 21)"
Communication Ports Receive and transmit data. For more information about the
various ports available for the RUGGEDCOM RMC30, refer to
"Communication Ports (Page 15)".
1.3 Required Tools and Materials
The following tools and materials are required to install the RUGGEDCOM RMC30:
Tools/Materials Purpose
AC or DC power cord (16 AWG) For connecting power to the device.
CAT-5 Ethernet cables For connecting the device to the network.
Flathead screwdriver For mounting the device to a DIN rail.
Phillips screwdriver For mounting the device to a panel.
4 x #8-32 screws For mounting the device to a panel.
1.4 Decommissioning and Disposal
Proper decommissioning and disposal of this device is important to prevent malicious
users from obtaining proprietary information and to protect the environment.
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 3

Introduction
1.4Decommissioning and Disposal
Decommissioning
This device may include sensitive, proprietary data. Before taking the device out of
service, either permanently or for maintenance by a third-party, make sure it has
been fully decommissioned.
For more information, refer to the associated Configuration Manual.
Recycling and Disposal
For environmentally friendly recycling and disposal of this device and related
accessories, contact a facility certified to dispose of waste electrical and electronic
equipment. Recycling and disposal must be done in accordance with local
regulations.
4RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Installing the Device 2
The following sections describe how to install the device, including mounting the
device, installing/removing modules, connecting power, and connecting the device
to the network.
DANGER
Electrocution hazard – risk of serious personal injury and/or damage to
equipment
Before performing any maintenance tasks, make sure all power to the device has
been disconnected and wait approximately two minutes for any remaining energy
to dissipate.
WARNING
Radiation hazard – risk of serious personal injury
This product contains a laser system and is classified as a CLASS 1 LASER PRODUCT.
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
CAUTION
Burn hazard – risk of serious personal injury
The surface of the device may be hot during operation, or as a result of the ambient
air temperature.
Wear appropriate personal protective equipment and use caution when working
with or around the device.
NOTICE
This product contains no user-serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate
specifications, test results, and agency approvals, and void the user's authority to
operate the equipment.
NOTICE
This product should be installed in a restricted access location where access can only
be gained by authorized personnel who have been informed of the restrictions and
any precautions that must be taken. Access must only be possible through the use
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 5

Installing the Device
2.1General Procedure
of a tool, lock and key, or other means of security, and controlled by the authority
responsible for the location.
2.1 General Procedure
The general procedure for installing the device is as follows:
Note
The user is responsible for the operating environment of the device, including
maintaining the integrity of all protective conductor connections and checking
equipment ratings. Make sure to review all operating and installation instructions
before commissioning or performing maintenance on the device.
1. Review the relevant certification information for any regulatory requirements.
For more information, refer to "Approvals (Page 25)".
2. Mount the device.
3. Set the operating mode.
4. Connect power to the device and ground the device to safety Earth.
5. Connect the device to the network.
6. Configure the device.
2.2 Unpacking the Device
When unpacking the device, do the following:
1. Inspect the package for damage before opening it.
2. Visually inspect each item in the package for any physical damage.
3. Verify all items are included.
Note
If any item is missing or damaged, contact Siemens for assistance.
2.3 Mounting the Device
The RUGGEDCOM RMC30 is designed for maximum mounting and display flexibility.
It can be equipped with adapters that allow it to be attached to a DIN rail or panel.
NOTICE
Heat generated by the device is channeled outwards from the enclosure. As such, it
is recommended that 2.5 cm (1 in) of space be maintained on all open sides of the
device to allow for some convectional airflow.
6RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Installing the Device
2.3.1Mounting the Device on a DIN Rail
Forced airflow is not required. However, any increase in airflow will result in a
reduction of ambient temperature and improve the long-term reliability of all
equipment mounted in the rack space.
Note
For detailed dimensions of the device with either DIN rail or panel hardware installed,
refer to "Dimension Drawings (Page 22)".
2.3.1 Mounting the Device on a DIN Rail
For DIN rail installations, the RUGGEDCOM RMC30 can be ordered with a DIN rail
adapter preinstalled on the back of the chassis. Use the adapter to mount the device
to a standard 35 mm (1.4 in) IEC/EN 60715 or TS35 DIN rail.
Mounting the Device
To mount the device to a DIN rail, do the following:
1. Hook the top teeth of the adapter onto the DIN rail.
Note
The adapter features a sliding release with a slot at the bottom for a flathead
screwdriver.
1
2
1
2
3
1
1 DIN Rail
2 DIN Rail Adapter
Figure2.1 Mounting the Device to a DIN Rail
2. Insert a flathead screwdriver into the slot of the sliding release and move it
down.
3. Push the device against the bottom of the DIN rail, then let go of the sliding
release to latch the device.
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 7

Installing the Device
2.3.1Mounting the Device on a DIN Rail
Removing the Device
To remove the device from a DIN rail, do the following:
1. Insert a flathead screwdriver into the slot of the sliding release and move it
down.
1
2
1
1
2
3
1 DIN Rail
2 DIN Rail Adapter
Figure2.2 Removing the Device from a DIN Rail
2. Swing the bottom of the device away from the DIN rail.
3. Lift the device off the DIN rail.
8RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Installing the Device
2.3.2Mounting the Device to a Panel
2.3.2 Mounting the Device to a Panel
To mount the device to a panel, do the following:
1. Disassemble the device and panel adapter.
a. Remove the screw at the bottom of the adapter.
b. Pull the device out of the adapter.
4
1
3
4
5
2
1 RUGGEDCOM RMC30
2 Panel Adapter
3 Mounting Holes
4 Screw
5 Metal Clips
Figure2.3 Panel Mounting
2. Place the panel adapter against the panel and align the adapater with the
mounting holes.
3. Secure the panel adapter using three #6-32 screws.
4. Insert the device into the adapter. Make sure the device is secured between the
two metal clips.
5. Install the screw previously removed from the bottom of the panel adapter.
2.4 Connecting Power
The RUGGEDCOM RMC30 supports a single integrated high AC/DC or low DC power
supply
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 9

Installing the Device
2.4.1Connecting AC Power
Note
• For 110/230 VAC rated equipment, an appropriately rated AC circuit breaker
must be installed.
• For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker
must be installed.
• Use minimum #16 gage copper wiring when connecting terminal blocks.
• Equipment must be installed according to applicable local wiring codes and
standards.
• All line-to-ground transient energy is shunted to the Surge Ground terminal. In
cases where users require the inputs to be isolated from ground, remove the
ground braid between Surge and Chassis Ground. Note that all line-to-ground
transient protection circuitry will be disabled.
Note
Siemens requires the use of external surge protection in VDSL applications where the
line may be subject to surges greater than that for which the device is rated. Use the
following specifications as a guide for VDSL external surge protection:
• Clamping Voltage: 50 V to 200 V
• Insertion Loss: < 0.1 dB at 10 MHz
• Peak Surge Current: 10 kA, 8x20µs waveform
2.4.1 Connecting AC Power
To connect a high AC power supply to the device, do the following:
NOTICE
Electrical hazard – risk of damage to equipment
Before testing the dielectric strength (HIPOT) in the field, remove the braided
ground cable connected to the surge ground terminal and chassis ground. This cable
connects transient suppression circuitry to chassis ground and must be removed to
avoid damage to transient suppression circuitry during testing.
10 RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10

Installing the Device
2.4.1Connecting AC Power
1. Connect the positive wire from the power source to the positive/live (+/L)
terminal on the terminal block.
1 2 3
4
1 Positive/Live (+/L) Terminal
2 Negative/Neutral (-/N) Terminal
3 Surge Ground Terminal
4 Braided Ground Cable
Figure2.4 Terminal Block Wiring
2. Connect the negative wire from the power source to the negative/neutral (-/N)
terminal on the terminal block.
3. Using a braided wire or other appropriate grounding wire, connect the surge
ground terminal to the chassis ground connection. The surge ground terminal
is used as the ground conductor for all surge and transient suppression circuitry
internal to the unit.
4. Connect the ground terminal on the power source to the chassis ground
terminal on the device.
RUGGEDCOM RMC30
Installation Manual, 04/2021, C79000-G8976-1008-10 11