Siemens EcoView 97-004 User manual

Installation Instructions
Document No. 129-906
July 20, 2016
Spanish Version
EcoV
iew
™
Thermostat
Item Number 129-906, Rev. EA Page 1 of 18
Para accede al documento en Español, escanee el código QR que se encuentra en la parte trasera del termostato.
Figure 1. 97-004 Thermostat.
Product Specifications
System Compatibility
Conventional Up to 3 Heating/3 Cooling
Heat Pumps Up to 4 Heating/2 Cooling
Electrical Characteristics
Power Supply 24 Vac +/-20%, Class 2, 4A
max.
Power Usage 5 VA (maximum)
Output Relay
Ratings Pilot duty, 1A max. per output, 4A max total
Ambient Limitations
Operating
Temperature 23°F to 122°F (-5°C to 50°C)
Storage/Shipping
Temperature -13°F to 158°F (-25°C to 70°C)
Relative
Humidity Up to 95% (non-condensing)
Enclosure
Rating NEMA 1
NOTE: The 97-004 is not battery-powered. It requires
24 Vac power from the HVAC equipment at
terminals RH/RC and C.
Product Number
97-004
Product Information
The EcoView Thermostat (97-004) is a wireless,
digital thermostat, designed for use with the
EcoView Energy Management System.
See the following documents for installation of other
EcoView system components:
•EcoView™ 8 DO Module Installation and
Commissioning (129-565)
•EcoView™Multi-phase Meter Installation
Instructions (129-563)
•EcoView™ Touchscreen Installation and
System Start-up (129-562)
Caution Notations
CAUTION/ATTENTION
Equipment damage or loss of data may
occur if you do not follow a procedure as
specified.
Risque de dégâts matériels ou de perte de
données, en cas de non-respect des
procédures à suivre.
Required Tools
•No. 1 Phillips screwdriver
•1/8” flat-blade screwdriver
•Drill with 1/8" drill bit
Expected Installation Time
15 minutes
Prerequisites
•All work must be performed in accordance with
applicable codes and standards.
•Use 18 gauge thermostat wire for equipment
connections.
•22 gauge shielded cable is recommended for
remote sensor wiring. Do not exceed 150 feet.
•To replace an existing thermostat, verify if 24
Vac is present between the RH/RC and C
terminals.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 2 of 18 Siemens Industry, Inc.
Prerequisites, Continued
•Turn off power to the HVAC equipment before
attempting to remove the existing thermostat.
•Record wiring connections to existing thermostat
terminals.
•Remove the existing thermostat before
proceeding.
Installation
The maximum distance between EcoView
Thermostats, EcoView Touchscreens, and other
EcoView ZigBee wireless devices is 75 to 300 feet
and will vary based on thermostat radio power
setting, local site geometry and local network
conditions. See EcoView Touchscreen Installation
and System Start-up (129-562) for information about
validating the communications of the EcoView
wireless devices with the EcoView Touchscreen.
1. Remove ZigBee MAC Address Label from the
thermostat rear housing, and store with
documentation for use in commissioning the
EcoView Energy Management System.
2. Install the thermostat base plate.
a. Feed the existing wires through the opening
in the base plate.
b. Secure the base plate to the mounting
surface using supplied hardware.
NOTE: Ensure that the UP arrows embossed
on the base plate point upward.
Figure 2. Thermostat Base Plate.
NOTE: If 24 Vac was verified as present at the
thermostat wires (see Prerequisites),
skip Step 3 and proceed to Step 4.
3. If 24 Vac is not present at the thermostat:
a. Locate the 24 Vac transformer or 24 Vac on
the terminal strip on the HVAC unit. Attach a
thermostat wire to the 24 Vac source. See
the HVAC equipment schematics to verify
the correct terminals.
b. Attach the other end of the unused wire to
the thermostat RH or RC terminal.
c. Verify that 24 Vac is present between the
RH/RC and C terminals.
4. Attach the existing wires to the appropriate
terminals on the thermostat base plate. See
Wiring Diagrams, Figure 4 and Figure 5.
NOTES: If using Auxiliary Inputs 1 to 4 or
configurable outputs 1 to 3, use
Setup Parameters P301 to P320 to
set functionality.
Corresponding inputs must be
configured in the Installer Set-up
menu to use remote inputs.
5. Systems with dual transformers:
If separate transformers are used for heating
and cooling systems, connect 24 Vac from the
cooling system to RC, and 24 Vac from the
heating system to RH. Remove Jumper RH-
RC.
6. (Optional) Aux Output 3 can be changed to a
dry (unpowered) contact by removing Jumper
RC-C3. See Figure 6.
NOTE: You cannot change the jumper after
plugging in the thermostat.
7. Attach thermostat to the base plate by engaging
tabs at the top and rotating the thermostat
downward until it is securely seated on the base
plate.
8. Secure the thermostat to the base plate with the
Phillips screws (provided), using the slots at the
bottom of the housing.
The installation is now complete. Restore power,
and continue to Thermostat Setup.
Thermostat Setup
Figure 3. Thermostat Display.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 3 of 18
Thermostat Display
Status Bar
The status bar at the top of the display consists of
11 icons.
Table 1. Status Bar Icons.
Icon Name Meaning
Occupied Space is occupied, based
on Schedule.
Keypad Lock Keypad is locked.
Scheduler Unit is running on the local
schedule.
Override The Scheduler is being
overridden by local control.
Humidity
Control
Indicator
Droplet and (+) indicates
humidification relay is on.
Droplet and (-) indicates
dehumidification relay is on.
If neither relay is on, the
water droplet does not
display.
Fan Fan relay is on.
Fresh Air Economizer Enable relay is
on.
Cool Mode The system is actively in
cooling mode.
Heat Mode The system is actively in
heating mode.
Heating/Cooling
Stages
Each segment represents
one stage of heating or
cooling.
Auxiliary
Heating
Auxiliary heating stage:
AUX=Stage 1: Aux 2=Stage
2
Navigation Bar
Only one function can be selected at a time. The
small bar (cursor) below the function icon indicates
that a function is selected. Pressing an icon twice
navigates back to the Main screen.
A double bar cursor below the Settings [ ] icon
indicates that you are in Programming mode.
The navigation bar at the bottom of the display
consists of four function icons.
Table 2. Navigation Bar Icons.
Icon Name Purpose
Setpoint
Enables adustment of temperature
and humidity (if applicable) setpoints.
Unit will display heating setpoint if in
Heating mode or cooling setpoint if in
Cooling mode.
Fan
Control
Enables fan relay to be controlled as
needed by thermostat (AUTO) or to
be on continuously (ON).
Mode
Selector
Enables manual changeover between
Heating and Cooling mode. AUTO will
enable the thermostat to automatically
switch between heating and cooling
mode as required. OFF will disable all
control functions.
Settings
Enables Scheduler, Time/Date, and
Installer Set Up configuration. Also
enables access to service reminder
and fault messages.
Service Reminders and Fault Messages
•Service reminders display at the right side of the
screen:
–SERVICE UV LAMP
–SERVICE HUMIDIFIER
–SERVICE AIR FILTER
They are determined by the timer set in the Installer
Setup Menu, and can be cleared by pressing the
Settings [ ] icon, and then SERVICE. See
Clearing Service Reminders.
•Active fault messages display at the left side of
the home screen:
–CONNECTION LOST
–DEMAND RESPONSE (Not applicable to this
model)
–SERVICE REQUIRED (See Viewing Fault
Messages)
Fault messages are automatically cleared when the
root cause of the failure is resolved.
Connection Lost
If communication with the EcoView Touchscreen is
lost, the thermostat will display CONNECTION LOST
and will control to the locally stored schedule. If a
local schedule has not been configured in the
thermostat, it will control to the last temperature
setpoint sent by the touchscreen.
When the connection is restored, the thermostat will
maintain control to the current setpoint until a new
setpoint is sent from the touchscreen.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 4 of 18 Siemens Industry, Inc.
Wiring Diagrams
Figure 4. Wiring Schematic, Conventional System.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 5 of 18
Figure 5. Wiring Schematic, Heat Pump.
Figure 6. Wiring Schematic, Aux Output 3.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 6 of 18 Siemens Industry, Inc.
Set-Up Wizard
When the unit is powered up for the first time, the
Set-Up WIZARD displays. This tool is used to
program the controller/thermostat.
NOTE: The thermostat will not start the control
sequence until the Set-Up Wizard is
complete.
1. Press WIZARD to access the menu.
2. Press +or –to change parameter settings, and
then use left and right arrows to select the
additional parameters.
3. After verifying all parameters, press Confirm to
save and complete.
4. INSTALLER displays. If setup is complete,
press the Settings [ ] icon to exit the Set-Up
Wizard. If further setup is needed, continue to
Step 5.
5. Press INSTALLER to access the Installer Menu
and more detailed setup. See Table 3 through
Table 9 for all parameter descriptions.
6. Press the Settings [ ] icon when finished to
exit setup.
Programming Temperature Setpoints
1. Touch the center of the Home screen to access
the room temperature screen. Use the left and
right arrows adjacent to the text line to display
the room temperature and humidity.
2. Touch the Setpoint [ ]icon of the screen to
access the room temperature and humidity
setpoints.
NOTE: Only the setpoints in the current mode
display and can be modified. For
instance, if the thermostat is in heating
mode, only the heating setpoint
displays and can be modified. If the
thermostat is in AUTO mode, both the
heating and cooling setpoints will be
displayed and can be modified.
3. Use the left [ï] and right [ð] arrows to access
the different setpoints, and the +and –icons to
adjust the setpoints.
4. Touch the center of the screen to exit Setpoint
Programming.
NOTE: If the screen is not touched for 30
seconds, the unit returns to the Home
screen.
Programming Time and Date
1. Touch the center of the Home screen.
2. Press the Settings [ ] icon.SCHEDULER
displays.
3. Use the left [ï] and right [ð] arrows to access
the Time menu. Press TIME. Press the two-digit
hour display to change the hour, or press the
two-digit minute display to change the minutes.
Press the left arrow [ï] to decrease the value,
and the right arrow [ð] to increase the value.
4. Press the Settings [ ] icon to save.
5. Use the left [ï] and right [ð] arrows to access
the Date menu. Press DATE. Use the arrows to
select the month and year; use +/-to set the
date.
6. Press the Settings [ ] icon to save.
Installer Menu
1. Touch the center of the Home screen.
2. Press the Settings [ ] icon. SCHEDULER
displays.
3. Press the left arrow [ï].
4. Press INSTALLER.
5. Using the lower left [ï] and right [ð] arrows,
enter the password.
6. Press PASSWORD to accept the password.
NOTE: The Installer Level default password is
00:00.
Press the Settings [ ] icon to accept changes and
return the unit to the Home screen.
NOTE: If you do not provide input, the thermostat
will automatically exit the Installer menu and
resume normal system control after five
minutes.
Programming the Schedule
1. Touch the center of the Home screen.
2. Press the Settings [ ]. Icon. SCHEDULER
displays.
3. Press SCHEDULER.
4. Use the left [ï] and right [ð] arrows to select
the day. Press the day to select.
5. Use the + and – icons to set the temperature
setpoints.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 7 of 18
6. Use the left [ï] and right [ð] arrows to adjust
the start time for each programming period. After
selecting the start time, confirm by touching
above the temperature display before moving to
the next programming period.
7. Depending on the setting on the Scheduler
(Parameter 107 – 108), set the schedule for
each period. See Table 3 for default schedules.
Resetting the Unit to Factory Defaults
CAUTION/ATTENTION:
The following steps set ALL parameters to
factory defaults (including passwords), and
restart the Set-Up Wizard.
Les étapes suivantes réglent TOUS les
paramètres à leur défaut d’usine (y compris
les mots de passes) et redémarrent
l’assistant de configuration.
1. Log in as either an Installer or Expert.
2. Press the left arrow [ï]. RESTORE displays.
3. Press + to change the setting to YES.
4. Press RESTORE.
This resets the unit and restarts the Set-Up Wizard.
Thermostat Setup for ZigBee
Network
1. Log in as either an Installer or Expert.
2. Use the left [ï]and right [ð] arrows to access
600 level parameters (see Table 9).
3. Verify default settings.
4. Access Parameter 605 (Add to ZigBee
Network) and touch the + icon to change to
YES.
Thermostat Commissioning
See EcoView™ Touchscreen Installation and
Commissioning (129-562) for instructions on linking
the thermostat to the EcoView Touchscreen.
Maintenance
Locking/Unlocking the Thermostat Display
To prevent unauthorized access to thermostat
settings, use Parameter P211 to configure screen
lockouts. The lock icon [ ] indicates that the
screen is locked. To unlock the keypad, do the
following:
1. Touch the center of the Home screen to access
the room temperature screen.
2. Press the Settings [ ] icon once; LOCKED
displays.
3. Press and hold the Settings [ ] icon for 5
seconds; PASSWORD displays.
4. Using the lower left [ï] and right [ð] arrows,
enter the INSTALLER password.
5. Press PASSWORD to accept the password.
6. Set Parameter 211 (Keypad Lockout) to zero
disable keypad lockout.
7. Touch the Setpoint [ ] icon to return to the
home screen.
Clearing Service Reminders
The thermostat displays SERVICE REQUIRED and
an associated service reminder if the reminder timer
(Parameters 208 through 210) has timed out. To
clear these, do the following:
1. Touch the center of the Home screen to access
the room temperature screen.
2. Press the Settings [ ] icon, and SERVICE
displays.
3. Use the left [ï] and right [ð] arrows to select
the service reminder.
4. To clear, touch the + icon and the display
changes from “-----“ to OFF.
5. Counter resets and reminder icons turn off.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 8 of 18 Siemens Industry, Inc.
Viewing Fault Messages
The thermostat displays SERVICE REQUIRED if a
sensor fail or service reminder has timed out. To
view these, do the following:
1. Touch the center of the Home screen to access
the room temperature screen.
2. Press the Settings [ ] icon, and SERVICE
displays.
3. Press SERVICE and review faults. Use the left
[ï] and right [ð] arrows to see all faults.
NOTE: The fault message is automatically cleared
when the root cause of the failure is
resolved.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 9 of 18
Table 3. 100 Series Parameters*.
Parameter Definition Display Value Range Default Extended Definition Notes
P101 System Type SYS TYPE CO
HP CO CO = Conventional System HP = Heat Pump
P102 Cooling
Stages COOL STGS
0
1
2
3
2Sets number of cooling stages
P103 Heating
Stages HEAT STGS
0
1
2
3
2Sets number of heating stages
P104 Aux Heating
Stages AUX HT STG 0
1
20Sets number of auxiliary heat stages
available for heat pump control. This parameter only displays if P101 = HP.
P105 Fan Operation HTG FAN No
Yes NO
YES = Fan Relay energized by thermostat
on call for heat
NO = Fan relay not energized by
thermostat on call for heat
If HVAC unit does not
start fan on call for
heat, set P105 to YES.
P106 Reversing
Valve REV VALVE O BOO = Energize reversing valve on cooling B = Energize reversing valve on heating This parameter only displays if P101 = HP.
P107 Scheduler
Days SCHEDULER
0
1
2
3
7
1
0 = Disable Scheduler
1 = Schedule all days with same
schedule
2 = One schedule for M through F and
another for Sat and Sun
3 = One schedule for M through F, Sat
and Sun scheduled individually
7 = Schedule each day individually
See Table 11 through
Table 15.
P108 Program
Periods PERIODS 2 42Sets number of program periods per day:
2 = 2 periods (Day/Night)
4 = 4 periods (Wake/Day/Evng/Night)
This parameter only
displays if P107 > 0.
P109 Units UNITS F
CFNOTE: Changing temperature units will reset all temperature- related parameters to their default values.
P110 Auto Change AUTO CHNGE YES
NO YES Enables auto change between heating and cooling.
This parameter does
not display on systems
that are heat only or
cool only.
P111 Changeover
Deadband DEADBAND 3°F to 9°F
(2.0°C to
5.0°C)
5°F
(3.0°C) Changeover deadband in degrees F (C)
This parameter does
not display if P110 =
NO.
This parameter forces a
separation between
heating and cooling
setpoints to prevent
short cycling of
heating/cooling cycles.
P112 Daylight
Savings DAYLT SAVE NO YES YES Y = Auto adjust for Daylight Savings Time
N = Does not auto adjust for Daylight
Savings Time
Daylight Savings Time
adjustment is based on
USA schedule.
* Included in Set-Up Wizard

Document No. 129-906
Installation Instructions
July 20, 2016
Page 10 of 18 Siemens Industry, Inc.
Table 4. 200 Series Parameters.
Parameter Definition Display Value Range Default Extended Definition Notes
P201 Heat Temp
Limit HEAT LIMIT 45°F to 95°F (7.0°C to 35.0°C) 95°F (35.0°C) Sets maximum allowable heating set point Does not display if P103 = 0.
P202 Cool Temp
Limit COOL LIMIT 50°F to 95°F
(10.0°C to
35.0°C)
50°F
(10.0°C) Sets minimum allowable cooling set point Does not display if P102 = 0.
P203 Temperature Display
Offset TMP OFFSET -5°F to 5°F
(-3..0°C to
3. 0°C)
0°F
(0°C)
Enables adjustment of control temp and display temperature in 1
degree increments. Applies only to onboard temp sensor. Indoor temp
only.
P206 Heat Pump Compressor
Lock Out HP COMP LO
OFF
15°F (-9.0°C)
20°F (-6.0°C)
25°F (-3.0°C)
30°F (-1.0°C)
35°F (1.0°C)
40°F (4.0°C)
45°F (7.0°C)
OFF
Heat pump compressor will not
operate below this outdoor
temperature, and will force unit to
auxiliary heat. An outdoor temperature
sensor is required.
NOTE: If P206 ≠OFF,
set P508 = 1°F (0.5°C)
This parameter only displays
for the following conditions:
- P101 = HP.
- P104 > 0.
- P105 = YES.
- P301, P305, P309, or P313
= 5
- P206 < P207.
P207 Heat Pump Auxiliary
Heat Lockout HP AUX LO
OFF
40°F (4.0°C)
45°F (7.0°C)
50°F (10.0°C)
55°F (13.0°C)
60°F (16.0°C)
OFF
Heat pump auxiliary heat will not
operate above this outdoor temp. An
outdoor temperature sensor is
required.
This parameter only displays
for the following conditions:
- P101 = HP.
- P104 > 0.
- P301, P305, P309, or P313
= 5
- P207 > P206.
P208 Service UV
Lamp UV LAMP 0 to 365 days 0
Number of calendar days until
SERVICE UV LAMP message
displays.
0 = Function disabled.
P209 Service
Humidifier HMDFR SRVC 0 to 365 days 0
Number of calendar days until
SERVICE HUMIDIFIER message
displays.
0 = Function disabled.
P210 Service Air
Filter FLTR SRVC 0 to 365 days 0
Number of calendar days until
SERVICE AIR FILTER message
displays.
0 = Function disabled.
P211 Keypad
Lockout KEY LOCK 0 = NONE
1 = PARTIAL
2 = FULL 0
0 = No Lockout
1 = Partial Lockout (only temp setpoint
can be adjusted)
2 = Total Lockout
Keypad lock [ ] icon
displays if P211 > 0.
P212 Clock Format CLOCK 12
24 12 12 = 12-hour format 24 = 24-hour format
P213 Backlight LIGHT 0 to 99 seconds 15 Number of seconds that backlight stays on after screen is touched.
0 = Always off.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 11 of 18
Table 5. 300 Series Parameters.
Parameter Definition Display Value
Range Default Extended Definition Notes
P301 Configurable
Input 1 (IN1) INPUT 1 0 300 = Not Used 3 = Supply Temp
See Table 16 for a list of
optional sensors approved
for use with the 97-004.
P302 Temperature
Input 1 Type TMP IN 1 0 100 = Type 2 Thermistor 1 = 0-10V Only displays if P301=3.
P303 Temperature
Input 1 Low TMP 1 LO
-58°F to
120°F **
(-50°C to
50.0°C)
0°F
(-18.0°C)
Calibrates thermostat to low end of temp
sensor signal (for example, 0V = -40°F
[4.4°C])
Only displays if P302=1
** P303<P304.
P304 Temperature
Input 1 High TMP 1 HI P303 value
** to 250°F
(120.0°C)
120°F
(50°C)
Calibrates thermostat to high end of
temp sensor signal at 10 volts (for
example, 10V = 250°F [120.0°C])
Only displays if P302=1.
** P304>303.
P305 Configurable
Input 2 (IN2) INPUT 2 0
1
200 = Not Used
1 = Indoor Temperature (Remote)
2 = Indoor Temperature (Average)
See Table 16 for a list of
optional sensors approved
for use with the 97-004.
P306 Temperature
Input 2 Type TMP IN 2 0 100 = Type 2 Thermistor 1 = 0 to 10V Only displays if P305=1 or 2.
P307 Temperature
Input 2 Low TMP 2 LO
-58°F to
120°F **
(-50°C to
50.0°C)
0°F
(-18.0°C) Calibrates thermostat to low end of temp sensor signal (for example., 0V = -40°F) Only displays if P306=1. ** P307<P308
P308 Temperature
Input 2 High TMP 2 HI P307 value
** to 250°F
(99.5°C)
120°F
(50.0°C)
Calibrates thermostat to high end of
temp sensor signal at 10 volts (for
example, 10V = 250°F)
Only displays if P306=1.
** P308>P307.
P309 Configurable
Input 3 (IN3) INPUT 3
0
4
5
6
7
9
A
0
0 = Not Used
4 = Return Temperature
5 = Outdoor/Aux.Temperature
6 = Remote Humidity Sensor (0 to 10V)
7 = CO2 (0 to 10V)
9 = Fault
A = Freezer, Cooler Temperature
- See Table 16 for a list of
optional sensors
approved for use with the
97-004.
- Selections for Inputs 3 & 4
cannot be duplicated.
P310 Temperature
Input 3 Type TMP IN 3 0 100 = Type 2 Thermistor 1 = 0 to 10V
Only displays if P309 = 4, 5,
or A..
P311 Temperature
Input 3 Low TMP 3 LO
-58°F to
120°F **
(-50°C to
50.0°C)
0°F
(-18.0°C) Calibrates thermostat to low end of temp sensor signal (Example: 0V = -40°F) - Only displays if P310 = 1. ** P311<P312.
P312 Temperature
Input 3 High TMP 3 HI P311 value
** to 250°F
(120.0°C)
120°F
(50.0°C)
Calibrates thermostat to high end of
temp sensor signal at 10 volts (for
example, 10V = 250°F)
- Only displays if P310 = 1.
** P312 > P311.
P313 Configurable
Input 4 (IN4) INPUT 4
0
4
5
6
7
9
A
0
0 = Not Used
4 = Return Temperature
5 = Outdoor/Aux. Temperature
6 = Remoste Humidity Sensor (0-10V)
7 = CO2 (0-10V)
9 = Fault
A = Freezer, Cooler Temperature
- See Table 16 for a list of
optional sensors
approved for use with the
97-004.
- Selections for Inputs 3 and
4 cannot be duplicated.
P314 Temperature
Input 4 Type TMP IN 4 0 100 = Type 2 Thermistor 1 = 0 to 10V Only displays if P313 = 4, 5, or A.
P315 Temperature
Input 4 Low TMP 4 LO
-58°F to
120°F **
(-50°C to
50.0°C)
0°F
(-18.0°C) Calibrates thermostat to low end of temp sensor signal (e.g., 0V = -40°F [4.4°C) Only displays if P314 = 1. ** P315 < P316.
P316 Temperature
Input 4 High TMP 4 HI P315 value
** to 250°F
(120.0°C)
120°F
(50.0°C
Calibrates thermostat to high end of
temp sensor signal at 10 volts (e.g., 10V
= 250°F [121.1°C])
Only displays if P314 = 1.
** P316>P315.
P317 Aux Output 1
(OUT1) AUX OUT 1 0
1
200 = Not Used
1 = Humidification
2 = Dehumidification
- Selections for Outputs 1 a
3 cannot be duplicated.
- If system is
conventional with 3H
+3C, AO1 is fixed as,
Stage 3 cooling.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 12 of 18 Siemens Industry, Inc.
Table 6. 300 Series Parameters (Continued).
Parameter Definition Display Value
Range Default Extended Definition Notes
P318 Aux Output 2
(OUT2) AUX OUT 2 0 500 = Not Used 5 = Economizer Enable Aux Out 2 is only used for Economizer Enable.
P319 Aux Output 3
(OUT3 & C3) AUX OUT 3 0
1
200 = Not Used
1 = Humidification
2 = Dehumidification
Selections for Outputs 1 and
3 cannot be duplicated.
P320 Independent Humidity
Control IND HMDTY Yes
No No
Yes = Humidification/dehumidification
relays can be energized
independent of heating/cooling
relays.
No = Humidification/dehumidification
relays are only energized if
heating or cooling relay is
energized
Select YES to activate
humidity control systems
regardless of whether there
is a need for heating or
cooling.
Table 7. 400 Series Parameters.
Parameter Definition Display Value
Range Default Extended Definition Notes
P401 Unit Number UNIT NMBR 1 to 999 --- Allows HVAC unit number to be
displayed on thermostat Home screen.
P407 Installer
Password INSTALL PW 0000 to 4999 0000 NOTE: If Installer Password is changed, a new password should be recorded for future reference.
P701 Firmware
Revision FIRMWARE X.X N/A Read Only
Expert Level Menus
1. Touch the center of the Home screen.
2. Press the Settings [ ] icon SCHEDULER
displays.
3. Press the left arrow.
4. Press INSTALLER.
5. Using the lower left and right arrows, enter the
password.
6. Press PASSWORD to accept the password and
return the unit to the Setup Menu.
NOTE: The Expert Level default password is
99:99.
7. See Table 3 through Table 10 and Installation
Notes in Wiring Diagrams for additional
information.
Press the Settings icon [ ] to accept changes and
return the unit to the Home screen. See Table 10 for
Expert Level parameter settings.
Recovering a Lost Password
If either of the default passwords is changed, the new
password(s) must be recorded and maintained for future
reference. If the records are misplaced, the following
procedure can be used to set new passwords.
1. Cycle power to the thermostat. This can be done
by loosening the securing screws on the bottom
of the housing and momentarily separating the
thermostat from the base plate.
2. Within 50 seconds of restoring power, navigate
to the installer setup screen and enter 98:21 as
the password.
3. The thermostat will go directly to the Expert
Level password screen. A new Expert Level
password can now be set.
4. After setting a new Expert Level password, the
thermostat will return to the Home screen.
5. The new Expert Level password can be used to
enter the full Expert Level setup menu where
both the Expert Level and Installer Level
passwords can now be set to new values.

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 13 of 18
Table 8. 500 Series Expert Settings Parameters.
(Only available if logged in as an Expert)
NOTE: P500 Series parameters are factory-set for optimum system performance. Changing these settings may degrade
efficiency and/or compromise occupant comfort.
Parameter Definition Display Value Range Default Extended Definition
P501 Interstage Delay - Cooling STG DLY CL 1 to 10 minutes 2 Time delay before next stage of cooling will be
activated.
P502 Interstage Differential - Cooling STG DIF CL 1°F (0.5°C) to
10°F (5.0°C) 1°F (0.5°C) Degrees above cooling deadband before Interstage Delay timer is initiated.
P503 Cooling Minimum Off Time M O T CL 1 to 10 minutes 5 Minimum time between compressor starts.
P504 Cooling Minimum On Time M R T CL 1 to 10 minutes 3 Minimum run time for any stage of cooling.
P505 Changeover Delay C-O DLY 1 to 60 10 Delay in minutes before system will automatically
switch from heating to cooling (or vice versa).
P506 Cooling Deadband CL DEADBND 1°F (0.5°C) to
5°F (4.0°C) 1°F
The deadband is divided equally above and below
setpoint. Cooling will begin when temperature
exceeds upper point of deadband and ceases
when temperature falls below lower point of
deadband.
P507 Interstage Delay - Heating STG DLY HT 1 to 10 minutes 2 Time delay before next stage of heating will be
activated.
P508 Interstage Differential - Heating STG DIF HT 1°F (0.5°C) to
5°F (5.0°C)
Conv. = 1°F
(0.5°C)
HP = 2°F
(1°C)
Degrees below heating deadband before
Interstage Delay timer is initiated.
NOTE: If P206 ≠OFF, set P508 = 1°F (0.5°C)
P509 Heating Minimum Off Time M O T HT 1 to 10 minutes 5 Minimum time between heating starts.
P510 Heating Minimum On Time M R T HT 1 to 10 minutes 3 (10 if heat
pump) Minimum run time for any stage of heating.
P511 Heating Deadband HT DEADBND 1°F (0.5°C) to
5°F (4.0°C) 1°F (0.5°C)
The deadband is divided equally above and below
setpoint. Heating will begin when temperature
falls below lower point of deadband and ceases
when temperature rises above upper port of
deadband.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 14 of 18 Siemens Industry, Inc.
Table 9. 600 Radio Parameters.
Parameter Definition Display Value
Range Default Extended Definition Notes
P601 Radio Power RADIO PWR 1
211 = High Power 2 = Low Power
P602 Communication
Failure COM FAIL 30 - 120 30 Number of minutes of no signal from
Master before stat assumes
communication failure
P603 Module Error
Count MOD ER CNT 0-100 60
P604 Transmitter
Error Count XMT ER CNT 5-100 60
P605 Add to ZigBee
Network ZIGBEE ADD No Yes Yes Does not display if unit is
connected to a ZigBee
network
P606 Remove from ZigBee
Network ZIGBEE RMV No
Yes No Does not display if unit is
NOT currently connected to a
ZigBee network
P607 ZigBee
Network NETWORK Open Closed Display Only Displays whether the joined devices are
currently allowing new devices to join
the device network.
P608 ZigBee MAC MAC Display
only Display Only Display tstat mac ID (16 characters)
Touch MAC to display first 16
characters. Touch arrows to
display subsequent
characters.
P609 ZigBee extPan-
Id EXT PAN ID Display only Display Only Display network extended Pan ID (16 characters)
Touch EX PAN ID to display
first 16 characters. Touch
arrows to display subsequent
characters.
P610 ZigBee FW ZIGBEE FW Display
only Display Only Display FW version
P611 ZigBee HW ZIGBEE HW Display
only Display Only Display HW version
P612 ZigBee RSSI RSSI Display
only Display Only Display RSSI, average of last 15 packets
P613 ZigBee Pan ID PAN ID Display
only Display Only Display Pan ID
P614 ZigBee
Channel CHANNEL Display only Display Only Display ZigBee Channel

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 15 of 18
Table 10. 900 Series Expert Settings Parameters.
(Only available if logged in as an Expert)
CAUTION/ATTENTION:
P900 Series parameters are for use by professional HVAC technicians during the system commissioning
process. Interlocks and time delays are defeated while using P900 parameters. Use of these parameters by
non-qualified personnel may result in equipment damage.
Les paramètres pour la série P900 sont utilisés par les techniciens professionels experts en CVCA durant les
procédures de mise en oeuvre du système. Les dispositifs de verrouillage ainsi que les temporisations sont
neuralisés lors de l’utilisation des paramètres P900. L’utilisation de ces paramètres par des employés
non-qualifiés peut causer des dommages matériels.
Parameter Definition Display Value Range Default Extended Definition
P901 Test Compressor 1 Y1 TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P902 Test Compressor 2 Y2 TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P903 Test Reversing Valve O/B TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P904 Test Fan G TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P905 Test Heat Stg 1 W1 TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P906 Test Heat Stg 2 W2 TEST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P907 Test Output 1 OUT1 TST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P908 Test Output 2 OUT2 TST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P909 Test Output 3 OUT3 TST ON
OFF OFF OFF = Relay not energized ON = Relay energized
P911 Expert Password XPRT PW 50:00 to 99:99 99:99
Auxiliary Sequences
The 97-004 primary sequences are designed to control
single and multi-stage heating/cooling systems to
maintain a user-selected temperature setpoint.
The following auxiliary sequences are available to
optimize occupant comfort and system efficiency:
Humidification
Parameters
•P317/P319: One of these must be set to 1
•P320: NO (default) = Humidification only occurs
if there is a call for heating or cooling. YES =
Humidification relay is energized independently
of heating and cooling relays.
•Humidity Setpoint: User adjustable to desired
level in humidification mode.
Sensors: Onboard humidity sensor or optional remote
humidity sensor.
Humidification relay will energize when measured
humidity drops approximately 4% below setpoint and de-
energize when measured humidity reaches setpoint.
Deadbands and proof timers are in force to prevent short
cycling.
Dehumidification
Parameters
•P317/P319: One of these must be set to 2.
•P320: NO (default) = Dehumidification only
occurs if there is a call for heating or cooling.
YES = Dehumidification relay is energized
independently of heating and cooling relays.
•Dehumidity Setpoint: User-adjustable to desired
level in dehumidification mode.

Document No. 129-906
Installation Instructions
July 20, 2016
Page 16 of 18 Siemens Industry, Inc.
Dehumidification, Continued
Sensors: Onboard humidity sensor or optional remote
humidity sensor.
Dehumidification relay will energize when measured
humidity rises approximately 4% above setpoint and de-
energize when measured humidity reaches setpoint.
Deadbands and proof timers are in force to prevent short
cycling.
Table 11. Single Schedule.
Day 2 Periods
Per Day 4 Periods Per Day
Phase Day Night Wake Day Evng Night
Setpoint
Heat, °F 70 62 70 62 70 62
Setpoint
Cool,°F 75 82 75 78 75 82
Time 6:00
AM 10:00 PM 6:00 AM 11:00 AM 1:00 PM 10:00 PM
NOTE: Daily Schedule – 2 periods per day: Parameter 107 = 1; Parameter 108 = 2
Daily Schedule – 4 periods per day: Parameter 107 = 1; Parameter 108 = 4; Parameter 109 = F
Table 12. Work Week Schedule with Weekend.
Day
NOTE: 2 Periods per Day
(Factory Default)
Parameter 107 = 2;
Parameter 108 = 2;
Parameter 109 = F NOTE: 4 Periods per Day Parameter 107 = 2; Parameter 108 = 4; Parameter 109 = F
Work Week
(Monday-
Friday)
Weekend
(Saturday-
Sunday) Work Week (Monday-Friday) Weekend (Saturday-Sunday)
Phase Day Night Day Night Wake Day Evng Night Wake Day Evng Night
Setpoint
Heat, °F 70 62 70 62 70 68 70 62 70 68 70 62
Setpoint
Cool, °F 75 82 75 82 75 78 75 82 75 78 75 82
Time 6:00
AM 10:00 PM 8:00 AM 10:00 PM 6:00 AM 11:00 AM 1:00 PM 10:00 PM 8:00 AM 11:00 AM 1:00 PM 10:00 PM
Table 13. Work Week Schedule with Separate Weekend Days - 2 Periods per Day.
Day Work Week
(Monday-
Friday)
Saturday Sunday
Phase Day Night Day Night Day Night
Setpoint
Heat, °F 70 62 70 62 70 62
Setpoint
Cool, °F 75 82 75 82 75 82
Time 6:00
AM 10:00 PM 8:00 AM 10:00 PM 8:00 AM 10:00 PM
NOTE: Individual Days, periods per day: Parameter 107 = 3; Parameter 108 = 2; Parameter 109 = F

Document No. 129-906
Installation Instructions
July 20, 2016
Siemens Industry, Inc. Page 17 of 18
Table 14. Work Week Schedule with Separate Weekend Days – 4 Periods Per Day.
Work Week (Monday-Friday) Saturday Sunday
Phase Wake Day Evng Night Wake Day Evng Night Wake Day Evng Night
Setpoint
Heat 70 68 70 62 70 68 70 62 70 68 70 62
Setpoint
Cool 75 78 75 82 75 78 75 82 75 78 75 82
Time 6:00
AM 11:00 AM 1:00 PM 10:00 PM 8:00 AM 11:00 AM 1:00 PM 10:00 PM 8:00 AM 11:00 AM 1:00 PM 10:00 PM
NOTE: Parameter 107 = 3; Parameter 108 =4; Parameter 109 = F
Table 15. Individual Days (Monday – Sunday).
Day 2 Periods
Per Day 4 Periods Per Day
Phase Day Night Wake Day Evng Night
Setpoint
Heat 70 62 70 62 70 62
Setpoint
Cool 75 82 75 78 75 82
Time 6:00
AM 10:00 PM 6:00 AM 11:00 AM 1:00 PM 10:00 PM
NOTE: Daily Schedule – 2 periods per day: Parameter 107 = 7; Parameter 108 = 2; Parameter 109 = F
Daily Schedule – 4 periods per day: Parameter 107 = 7; Parameter 108 = 4; Parameter 109 = F
Table 16. Suggested Sensors for Use with 97-004.
Siemens Part
Number Description Signal Format
97-002 Remote Wall-Mounted Sensor – Temperature Only 10K Ohm, Type II NTC
QFA33SS.EWNN Remote Wall-Mounted Temperature and Humidity Sensor 0-10V
QAM2030.010 Duct-Mounted Temperature Sensor 10K Ohm, Type II NTC
QFM2160U Duct-Mounted Temperature & Humidity Sensor 0-10V
QAC2030 Outdoor Air Temperature Sensor 10K Ohm, Type II NTC
QAD2030 Surface-Mount Pipe Temperature Sensor 10K Ohm, Type II NTC

Document No. 129-906
Installation Instructions
July 20, 2016
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as
design improvements are introduced. EcoView is a trademark of Siemens Industry, Inc. Other product or company names mentioned herein may be the
trademarks of their respective owners. © 2016 Siemens Industry, Inc.
Siemens Industry, Inc.
Building Technologies Division
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
USA
Tel. [phone]
Your feedback is important to us. If you have
comments about this document, please send them
[e-mail]
Document No. 129-906
Printed in the USA
Page 18 of 18
FCC and IC Interference Requirements
“This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.”
"Le présent appareil est conforme aux CNR D'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisé aux deux
conditions suivantes : (1) l'appareil de doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement." (Per RSS-Gen Issue 3 [December 2010 Section 7.1.3])
FCC Note
This device complies with Part 15 of the FCC rules. Changes or modifications not expressly approved by Siemens Industry Inc. could void the user’s
authority to operate the equipment. (FCC Code of Federal Regulations Title 47 Part 15.21)
FCC and IC Radiation Exposure Statement for Mobile Devices
“This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and
operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be re-located or operating in conjunction with any
other antenna or transmitter.” (For compliance with FCC Code of Federal Regulations Title 47 Part 2.1091)
FCC Code of Federal Regulations Title 47 Part 15.105:
Information to the User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna
--Increase the separation between the equipment and the receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
For Industry Canada Users
“This Class B digital apparatus complies with Canadian ICES-003 Issue 4 (February 2004).”
Cet appareil numérique de la classe B est conforme à la norme ICES-003 – numéro 4 (février 2004) du Canada.
Antenna
“Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.”
"Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un grain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante."
Limited Warranty
Siemens Product Guard Warranty warrants the purchased from it or its authorized reseller to be free from defects in material and workmanship under
normal use during the two year period commencing on the date of purchase. The written proof of purchase is required for such warranty period to apply.
The software included in this Siemens product is licensed for use subject to the Siemens end-user license agreement (“EULA”) posted at
www.usa.siemens.com/btcpseula (Siemens’ EULA web site) for this software identified by product model or part number on the Siemens EULA web site.