Siemon 10G 6 User manual

MODULAR PATCHING
WWW.SIEMON.COM
10G 6™HD®PATCH PANEL
The greatest challenge to achieving superior NEXT performance in a channel is
at the cross-connect in the telecommunications room. With two outlets in close
proximity connected by a short modular cord, achieving NEXT margin above
category 6 is a challenge for common patch panels. Not so with Siemon’s
10G 6 HD modular patch panel!
Part of Siemon’s new 10G ip™Cabling Solution, the 10G 6 HD modular patch
panel far exceeds all category 6 component and channel requirements. This
superior level of performance is achieved via a completely new circuit board
design, optimization of jack pin geometry, and stringent inspection and quality
control procedures. When used with a 10G 6 MC®patch cord, the result is a
cross-connect solution with typical NEXT margin of 10 dB across the category
6 frequency range from 1-250 MHz, and useable bandwidth to 500 MHz —
necessary for next generation applications.
Combine the 10G 6 MC modular cord with Siemon’s new 10G 6 MAX®modules
and 10G 6 HD patch panels for a complete 10G 6 channel solution. This superior
10G 6 cabling system delivers unparalleled network performance today and
supports emerging Internet Protocol (IP) applications like Voice Over IP (VoIP) and
IP video.
Our circuit board is tuned and balanced using our
patent-pending phase-delay technology to
maximize margin to category 6 and beyond
Pyramid
™
wire entry system on S310
®
blocks
separates paired conductors when lacing
cables to simplify and reduce installation time
Protective rear metal housing prevents
accidental damage of internal circuit board
Black anodized finish and
rolled steel edges provide a
durable, aesthetic appearance
Superior performance for
interconnect, cross-connect or
consolidation point applications
Designation area
provided for panel
identification
Includes rear cable
manager to properly
guide cables to point
of termination Backwards compatible
with category 6/class E
and lower patch cords
Durable modular outlets are FCC
CFR 47 part 68 subpart F and IEC
60603-7 compliant. Outlet
contacts are plated with 1,27
microns of gold
Terminates with standard
110 termination tools
T568A and T568B
wiring compatible


500 MHz
Supports
10GBASE-T
Applications

PROD-SS-HD10G6 Rev. B 9/05
© 2005 Siemon
MODULAR PATCHING
Siemon — EMEA HQ & UK
United Kingdom
Tel: [phone]
Siemon — France
Paris
Tel: [phone]
Siemon — Deutschland
Frankfurt
Tel: [phone]
PRODUCT INFORMATION
Siemon — Italia
Milano
Tel: [phone]
WWW.SIEMON.COM
10G 6™HD®Patch Panels:
10GHD-24....................24-port panel, T568A/B wiring, 1 U
10GHD-48....................48-port panel, T568A/B wiring, 2 U
For additional resource information:
Visit our web site at www.siemon.com
Because we continuously improve our products, Siemon
reserves the right to change specifications and availability
without prior notice.
10G 6
™
, 10 G ip
™
, HD
®
, MC
®
, MAX
®
, Pyramid
™
, S210
®
and S310
®
are
trademarks of Siemon
Panels include rear cable manager, icon label holders,
designation labels, cable ties, and mounting hardware
Add “B” to end of part number for bulk project pack of 5
panels (rear cable managers and icon label holders not
included but can be ordered separately).
Note: 1 U = 44.5mm
훾
For related product information request Spec Sheet(s):
10G 6 MC®Patch Cords (PROD-SS-MC10G6)
10G 6 MAX®Modules (PROD-SS-MX10G6)
10G 6 BladePatch™(PROD-SS-10G6BDP)
100 MHz
NEXT
60
50
40
30
20
10
0
dB
250 MHz 500 MHz
45
40
35
30
25
20
15
10
5
0
dB
ELFEXT
Return Loss
dB
Insertion Loss
60
50
40
30
20
10
0
dB
Augmented Cat 6 Limit †Worst Case Typical
100 MHz 250 MHz 500 MHz
30
25
20
15
10
5
0
100 MHz 250 MHz 500 MHz 100 MHz 250 MHz 500 MHz
4 Connector Channel Performance Data for 10G 6
™
UTP Solution*
*4 Connector Channel Performance Data utilizes 10G 6 Patch
Panel, 10G 6 MAX
®
UTP Modules, and 10G 6 MC
®
UTP
Modular Cords or 10G 6 BladePatch
™
UTP Patch Cord
†
Performance from 250-500 MHz based on extrapolated
TIA/EIA-568-B.2-10 Draft 1.3