SIGLENT SHA800A User manual

1
Quick Guide
SHA800A
Spectrum &
Network Analyzer
Quick Guide
EN_01A

SHA800A QuickGuide I
Guaranty and Declaration
Copyright
SIGLENT TECHNOLOGIES CO., LTD All Rights Reserved.
Trademark Information
SIGLENT®is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.
Declaration
⚫SIGLENT products are protected by patent law worldwide.
⚫SIGLENT reserves the right to modify or change parts of or all the
specifications or pricing policies at company’s sole decision.
⚫Information in this publication replaces all previous corresponding material.
⚫Any way of copying, extracting or translating the contents of this manual is not
allowed without the permission of SIGLENT.
⚫SIGLENT will not be responsible for losses caused by either incidental or
consequential in connection with the furnishing, use or performance of this
manual as well as any information contained.
Product Certification
SIGLENT guarantees this product conforms to the national and industrial
standards in China as well as the ISO9001: 2008 standard and the ISO14001:
2004 standard. Other international standard conformance certification is in
progress.

II SHA800A QuickGuide
Contents
Guaranty and Declaration.............................................................................I
Contents......................................................................................................II
Important Safety Information .......................................................................1
Safety Compliance.......................................................................................8
General Inspection.......................................................................................9
Preparing for Use.......................................................................................10
Firmware Operation...................................................................................23
Remote Control..........................................................................................25
Service and Support..................................................................................25
Troubleshooting.........................................................................................26

SHA800A QuickGuide 1
Important Safety Information
This manual contains information and warnings that must be followed by the user
for safe operation and to keep the product in a safe condition.
General Safety Summary
Carefully read the following safety precautions to avoid any personal injury or
damage to the instrument and any products connected to it. To avoid potential
hazards, please use the instrument as specified.
To Avoid Fire or Personal Injury
Use Proper AC Power Line
Only the power cord designed for the instrument and authorized by local country
should be used.
Ground the Instrument
The instrument is grounded through the protective earth conductor of the power
line. To avoid electric shock, please make sure the instrument is grounded correctly
before connecting its input or output terminals.
Look Over All Terminals’ Ratings
To avoid fire or electric shock, please look over all ratings and sign instructions of
the instrument. Before connecting the instrument, please read the manual carefully
to gain more information about the ratings.
Equipment Maintenance and Service
When the equipment fails, please do not dismantle the machine for maintenance.
The equipment contains capacitors, power supply, transformers, and other energy
storage devices, which may cause high voltage damage. The internal devices of
the equipment are sensitive to static electricity, and direct contact is easy to cause
irreparable damage to the equipment. It is necessary to return to the factory or the
company's designated maintenance organization for maintenance.
Be sure to pull out the power supply when repairing the equipment. Live line
operation is strictly prohibited. The equipment can only be powered on when the
maintenance is completed and the maintenance is confirmed to be successful.

2SHA800A QuickGuide
Identification of Normal State of Equipment
After the equipment is started, there will be no alarm information and error
information at the interface under normal conditions. The curve on screen will scan
from left to right freely; if there is a button in the scanning process or is an alarm or
error prompt, the device may be in an abnormal state. You need to view the specific
prompt information. You can try to restart the setting. If the fault information is still in
place, do not use it for testing. Contact the manufacturer or the maintenance
department designated by the manufacturer to carry out maintenance to avoid
sabotage data by fault operations or endanger the personal safety.
Not Operate with Suspected Failures
If you suspect that there is damage to the instrument, please let qualified service
personnel check it.
Avoid Circuit or Wire Components Exposed
Do not touch exposed connectors or components when the power is on.
Do not operate in wet/damp conditions
Do not operate in an explosive atmosphere
Keep the surface of the instrument clean and dry
Not to use the equipment for measurements on mains circuits, not to use the
equipment for measurements on voltage over the voltage range described in
the manual. The maximum additional transient voltage cannot exceed 1300V.
The responsible body or operator should refer to the instruction manual to
preserve the protection afforded by the equipment. If the equipment is used
in a manner not specified by the manufacturer, the protection provided by the
equipment may be impaired.
Any parts of the device and its accessories are not allowed to be changed or
replaced, other than authorized by the manufacturer or agent.

SHA800A QuickGuide 3
Safety Terms and Symbols
When the following symbols or terms appear on the front or rear panel of the
instrument or in this manual, they indicate special care in terms of safety.
This symbol is used where caution is required. Refer to the
accompanying information or documents to protect against
personal injury or damage to the instrument.
This symbol warns of a potential risk of shock hazard.
This symbol is used to denote the measurement ground
connection.
This symbol is used to denote a safety ground connection.
This symbol shows that the switch is an On/Standby switch.
When it is pressed, the analyzer’s state switches between
Operation and Standby. This switch does not disconnect the
device's power supply. To completely power off the analyzer,
the power cord must be unplugged from the AC socket after
the instrument is in the standby state.
This symbol is used to represent alternating current, or “AC”.
CAUTION
The “CAUTION”symbol indicates a potential hazard. It calls
attention to a procedure, practice, or condition which may be
dangerous if not followed. Do not proceed until its conditions
are fully understood and met.
WARNING
The “WARNING”symbol indicates a potential hazard. It calls
attention to a procedure, practice, or condition which, if not
followed, could cause bodily injury or death. If a WARNING is
indicated, do not proceed until the safety conditions are fully
understood and met.

4SHA800A QuickGuide
Working Environment
The design of the instrument has been verified to conform to EN 61010-1 safety
standard per the following limits:
Environment
The instrument is used indoors and should be operated in a clean and dry
environment with an ambient temperature range.
Note: Direct sunlight, electric heaters, and other heat sources should be
considered when evaluating the ambient temperature.
Warning: Do not operate the instrument in explosive, dusty or humid
environments.
Ambient Temperature
Operating: 0 ℃to +50 ℃
Non-operation: -30 ℃to +70 ℃
Note: Direct sunlight, radiators, and other heat sources should be considered when
assessing the ambient temperature.
Humidity
Operating: 5% ~ 90 %RH, 30 ℃, derate to 50 %RH at 40 ℃
Non-operating: 5% ~ 95% RH
Altitude
Operating: ≤ 3,000 m, 25 ℃
Non-operating: ≤ 12,000 m

SHA800A QuickGuide 5
Installation (overvoltage) Category
This product is powered by mains conforming to installation (overvoltage) Category
II.
Note: Installation (overvoltage) category I refers to situations where equipment
measurement terminals are connected to the source circuit. In these terminals,
precautions are done to limit the transient voltage to a correspondingly low level.
Installation (overvoltage) category II refers to the local power distribution level
which applies to equipment connected to theAC line (AC power).
Degree of Pollution
The analyzers may be operated in environments of Pollution Degree II.
Note: Degree of Pollution II refers to a working environment where dry and
non-conductive pollution occurs. Occasional temporary conductivity caused by
condensation is expected.
IP Rating
IP20 (as defined in IEC 60529).
Cooling Requirements
This instrument relies on the forced air cooling with internal fans and ventilation
openings. Care must be taken to avoid restricting the airflow around the apertures
(fan holes) at each side of the analyzer. To ensure adequate ventilation it is
required to leave a 15 cm (6 inch) minimum gap around the sides of the instrument.
CAUTION: Do not block the ventilation holes located on both sides
of the analyzer.
CAUTION: Do not allow any foreign matter to enter the analyzer
through the ventilation holes, etc.

6SHA800A QuickGuide
Power and Grounding Requirements
The instrument operates with a single-phase, 100 to 240 Vrms (+/-10%) AC power
at 50/60 Hz (+/-5%), or single-phase 100 to 120 Vrms (+/-10%) AC power at 400 Hz
(+/-5%).
No manual voltage selection is required because the instrument automatically
adapts to line voltage.
Depending on the type and number of options and accessories (probes, PC port
plug-in, etc.), the instrument can consume up to 193 W of power.
Note: The instrument automatically adapts to the AC line input within the following
ranges:
Voltage Range:
90 - 264 Vrms
90 - 132 Vrms
Frequency Range:
47 - 63 Hz
380 - 420 Hz
The instrument includes a grounded cord set containing a molded three-terminal
polarized plug and a standard IEC320 (Type C13) connector for making line
voltage and safety ground connection. The AC inlet ground terminal is connected
directly to the frame of the instrument. For adequate protection against electrical
shock hazards, the power cord plug must be inserted into a mating AC outlet
containing a safety ground contact. Use only the power cord specified for this
instrument and certified for the country of use.
Warning: Electrical Shock Hazard!
Any interruption of the protective conductor inside or outside of the
analyzer, or disconnection of the safety ground terminal creates a
hazardous situation. Intentional interruption is prohibited.
The position of the instrument should allow easy access to the socket. To make the
instrument completely power off, unplug the instrument power cord from the AC
socket.

SHA800A QuickGuide 7
The power cord should be unplugged from the AC outlet if the analyzer is not to be
used for a long time.
CAUTION: The outer shells of the front panel terminals are
connected to the instrument’s chassis and therefore to the safety
ground.
Cleaning
Clean only the exterior of the instrument, using a damp, soft cloth. Do not use
chemicals or abrasive elements. Under no circumstances allow moisture to
penetrate the instrument. To avoid electrical shock, unplug the power cord from the
AC outlet before cleaning.
Warning: Electrical Shock Hazard!
No operator serviceable parts inside. Do not remove covers.
Refer servicing to qualified personnel.
Abnormal Conditions
Do not operate the analyzer if there is any visible sign of damage or has been
subjected to severe transport stresses.
If you suspect the analyzer’s protection has been impaired, disconnect the power
cord and secure the instrument against any unintended operation.
Proper use of the instrument depends on careful reading of all instructions and
labels.
Warning: Any use of the analyzer in a manner not specified by the
manufacturer may impair the instrument’s safety protection. This
instrument should not be directly connected to human subjects or
used for patient testing.

8SHA800A QuickGuide
Safety Compliance
U.S. nationally recognized testing laboratory listing
1. UL 61010-1:2012/R: 2018-11. Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use –Part 1:
General Requirements.
2. UL 61010-2-030:2018. Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use –Part2-030: Particular
requirements for testing and measuring circuits.
Canadian certification
1. CAN/CSA-C22.2 No. 61010-1:2012/A1:2018-11. Safety Requirements
for Electrical Equipment for Measurement, Control, and Laboratory Use –
Part 1: General Requirements.
2. CAN/CSA-C22.2 No. 61010-2-030:2018. Safety Requirements for
Electrical Equipment for Measurement, Control, and Laboratory Use –
Part 2 - 030: Particular requirements for testing and measuring circuits.

SHA800A QuickGuide 9
General Inspection
Inspect the shipping container
Keep the damaged shipping container or cushioning material until the contents of
the shipment have been completely checked and the instrument has passed both
electrical and mechanical tests.
The consigner or carrier will be responsible for damages to the instrument resulting
from shipment. SIGLENT will not provide free maintenance or replacement.
Inspect the instrument
If the instrument is found to be damaged, defective or fails in electrical or
mechanical tests, please contact SIGLENT.
Check the accessories
Please check the accessories according to the packing list. If the accessories are
incomplete or damaged, please contact your SIGLENT sales representative.

10 SHA800A QuickGuide
Preparing for Use
Appearance and Dimension
Front and lateral View
The included tilting stand is available for desktop operation. The tilting bracket
provides a backward tilt for improved stability. To deploy the tilt bracket, pull the
bottom of the tilt bracket away from the back of the instrument. To retract the tilting
bracket, push the bottom of the bracket toward the back of the instrument.
Side View
Unit：mm

SHA800A QuickGuide 11
Power Supply Information
The battery that comes with the SHA800A may need to be recharged before use.
The device can use the supplied AC-DC adapter (refer to the product technical data
sheet for ordering information). The specifications of the input AC power supply are:
100-240V, 50/60Hz; Or charge through the on-board DC adapter in the accessory.
Specifically, the analyzer can be connected to the adapter according to the power
socket shown in the figure below.
Rear View and Power
◆Adapter factory configuration is the 12V 4A
◆Battery factory installed, the user can change itself
WARNING
This instrument can only use Siglent approved batteries, adapters
and chargers. When using an onboard DC adapter, always ensure
that the power supply is rated at least 75 W @ 15 VDC and that
there is no dust or debris on the socket. If the adapter plug
becomes hot during operation, discontinue use immediately.
Siglent recommends taking out the batteries when devices aren't
used for too long.
Power socket

12 SHA800A QuickGuide
Front Panel
12 3 4
5
6
7
The Front Panel
Front Panel Description
NO.
Name
Description
1
LCD Screen
8.4 inch multi-touch screen, resolution 800*600
2
Power Switch
Stand by status: Orange
Power on status: White
Short press: To Stand by status with current
state saved
Long press: To Stand by status without current
state saved
3
Function Keys
Complete the function control and parameter
input of the analyzer, and most operations can
be completed by the touch screen.
Press Lock to turn off/on the keyboard and
touch functions.
4
Three-dimensional
knob
Complete the quick adjustment and selection of
parameters.

SHA800A QuickGuide 13
5
Fan vent
Built-in fan external exhaust port. Please ensure
that this vent is unblocked.
6
Battery case cover
Internal battery protection cover. Remove during
battery replacement.
7
Detachable
hand strap
Convenient hand force, can be installed on both
sides.
Shorcut Keys Description
Name
Description
The menu selection window pops up on the screen, and you can
use the touch screen control to directly enter a function menu.
Shortcut screenshot button to save the current screen display as
a picture. Save parameters, such as path, reverse color, and
screenshot area, to be set in System > File .
Measurement control, pause or resume the current measurement
process. When the button light is on, the measurement is
suspended. When the button light is off, the measurement is
resumed.
Key and touch screen lock control.
When the button light is on, all key pad buttons and touch screen
buttons except the Lock button are locked to prevent
misoperation.

14 SHA800A QuickGuide
The function key part of the front panel is the reuse key of menu selection mode
and value input mode, which can be switched by Enter and Esc :
◆Under default reset, the operation interface is in menu selection mode, and
function keys will be identified as the blue silk screen function identifier on the
upper side of the key. Use Enter to switch from menu selection mode to
value input mode.
◆When the operation interface is in value input mode, the multiplex key will be
identified as the white silk screen digital identifier inside the key. You can use
Esc to switch from value input mode to menu selection mode.
Function Keys Description
Name
Description
Menu selection mode, to select the analyzer operation mode,
such as spectrum analysis mode, antenna and cable test mode,
network analyzer mode, etc.
In menu selection mode, control of mode measurement
parameters, such as average times, specific test items, etc.
In menu selection mode, frequency parameters are controlled. In
time domain analysis, length (distance) parameters are
controlled.
Menu selection mode, bandwidth class parameter control, such
as RBW, VBW, IFBW and so on.

SHA800A QuickGuide 15
In menu selection mode, control cursor Marker parameters, such
as cursor type, cursor positioning, noise cursor, N dB bandwidth,
etc.
Menu selection mode, for amplitude class parameters control,
such as scale and unit, as well as preattenuator, preamplifier,
amplitude correction, etc.
In the menu selection mode, control the scanning parameters,
such as scanning time and type, scanning number, trigger,
gating, etc.
In the menu selection mode, control the peak parameters, such
as peak search, peak rule setting, etc.
In menu selection mode, trace parameters are controlled, such
as trace state, detection, mathematical calculation,
normalization, etc.
In menu selection mode, control the parameters of limit line,
such as limit line editing, margin, test state setting, etc.
In menu selection mode, port calibration of antenna and cable
test mode and network analysis mode is carried out, such as
selecting the type of mechanical calibration part, user-defined
calibration part parameters, loading electronic calibration part,
etc.
In menu selection mode, reset parameters can be controlled,
such as reset status definition, power-on status definition, user
status definition, etc.
In the menu selection mode, you can perform file operations,
such as saving and invoking files, and viewing file browsers.
In menu selection mode, the system general information view,
version and calibration operation, as well as input and output
port Settings, screen display Settings, etc.

16 SHA800A QuickGuide
Rear Panel
124
568910 11 12
3
7
Rear Panel
Rear Panel Description
NO.
Name
Description
1
RF In/Port 2
Signal input: 50Ω N female connector.
Maximum input ±50 VDC, + 30 dBm.
2
Trig In
Trigger input is a BNC female connector. When the
analyzer uses an external trigger mode, the
connector receives a rising or falling edge of an
external trigger signal that is used to establish event
synchronization.
3
Ref In
Reference clock input, BNC female connector. The
analyzer can use an internal reference clock or an
external reference clock. If the instrument detects a
signal from an external 10 MHz reference clock, it
automatically uses the signal as the analyzer's
reference clock source. At this time the screen status
bar frequency reference display external;
When the external 10 MHz reference signal is lost,