SIGMA TEK HGW 1033-01 User manual

Date of creation: 16.08.2019 Version date: 22.02.2022 Article number: 12-246-1033-01-E
HGW 1033-01
Wireless Handheld Operating Panel
Operating Manual

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2019
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible
for technical or printing errors in this handbook and assumes no responsibility for damages that occur through
its use.

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
Wireless Handheld Operating Panel HGW 1033-01
In combination with a BWH base station and a
PLC, the HGW 1033-01 is a wireless, intelligent
handheld operating unit that enables the
programming, visualization and diagnosis of
processes and systems control.
Process data, procedures and parameters are
comfortably presented on the 10.1” display and
can be entered or changed via the touch screen.
The HGW 1033-01 can be coupled with machines
via base stations, which allows the flexible
application of the operating unit.
The interfaces can be used to configure the
terminal. The integrated battery pack allows 2 hours of operation at full capacity.
22.02.2022 Page 1

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
Table of Contents
1 Introduction 6
1.1 Target Group/Purpose of this Operating Manual 6
1.2 Important Reference Documentation 6
1.3 Contents of Delivery 6
2 Basic Safety Guidelines 7
2.1 Symbols Used 7
2.2 Disclaimer 9
2.3 General Safety Guidelines 10
2.4 Software/Training 12
3 Standards and Guidelines 13
3.1 Guidelines 13
3.1.1 EU Conformity Declaration 13
3.2 Wireless System Operation 14
4 Technical Data 15
4.1 Performance Data 15
4.2 Electrical Requirements 16
4.3 Display 17
4.4 Control Unit 18
4.5 Input 18
4.6 Environmental Conditions 19
4.7 Wireless 20
4.7.1 WLAN 2.4 GHz 21
4.7.2 WLAN 5 GHz 21
4.7.3 Antennae 21
4.8 Miscellaneous 22
5 Interfaces 23
Page 2 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
5.1 Connections Bottom 23
5.1.1 X1: USB 2.0 (Type A) 24
5.1.2 X2: USB 2.0 DualRole (Type C) 25
5.2 Rear Connectors 26
5.2.1 X15: Power/Data 27
5.3 Display 28
5.3.1 Underside 28
5.3.2 Front 29
5.3.2.1 Status LEDs 29
5.4 WLAN 30
5.5 Acoustics 31
5.6 On/Off Button (illuminated) 32
6 Mechanical Dimensions 33
6.1 HGW 33
6.2 HGW with BWH 34
7 Assembly/Installation 35
7.1 Check Contents of Delivery 35
7.2 Preparing the Hardware 35
8 Status and Error Messages 36
9 Battery 46
9.1 Introduction 46
9.2 Charge Status and Aging 46
9.2.1 BatteryLevelAbsolute 46
9.2.2 BatteryLevel 46
9.2.3 BatteryStateofHealth 46
9.3 Versions 47
9.4 Battery Transport/Storage 48
22.02.2022 Page 3

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
9.5 Commissioning and Charging Options 48
9.5.1 Monitoring of the Charging Source 49
9.6 Battery Operating Ranges 50
9.7 Hardware Class 52
9.8 Exchanging the Battery 52
9.8.1 Deep Discharged Battery 53
9.8.2 Recommendation 53
9.9 DeepSleepMode 54
9.9.1 Conditions 54
9.10 Transport Mode 54
9.10.1 Activating the Transport Mode 55
9.10.1.1 Conditions 55
9.10.1.2 Note 55
9.10.2 Ending the Transport Mode 56
9.11 Log Data 56
10 Operation/Start-up 58
10.1 Note 58
10.2 WLAN Channels and Settings 59
10.3 Configuration 60
10.3.1 Example 60
10.4 Testing the Operating Area 61
10.5 Operation 61
10.5.1 General 61
10.5.2 Turning On 62
10.5.3 Non-Safety Mode 63
10.5.4 Turning Off 63
11 Help with Disruptions/Troubleshooting 64
Page 4 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
12 Transport/Storage 65
13 Storage 66
14 Maintenance 67
14.1 Cleaning and Disinfecting the Touch Screen 67
14.2 Service 68
14.2.1 Calibrating the Touch Screen 68
14.3 Repair 69
15 Disposal 70
16 Accessories 71
16.1 Antennae 71
16.2 Touch Pen 71
16.3 Edge Protection 71
17 Application Information 72
17.1 Visualization 72
17.1.1 Example Application 72
17.2 Updates 73
22.02.2022 Page 5

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
lProject planners
lTechnicians
lCommissioning engineers
lMachine operators
lMaintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found on
our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
lHGW 1033-X_Maintenance Manual
lHGW_BWH_Configuration Manual
lWLAN Configuration
lHW IP Address Settings
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x HGW 1033-01
Page 6 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes.
DANGER
Danger indicates that death or serious injury will occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
22.02.2022 Page 7

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
DANGER
Danger for persons with pacemakers, implanted defibrillators or other
active implants.
Danger pour les personnes portant un stimulateur cardiaque, un
défibrillateur implanté ou d'autres implants actifs
WARNING
Magnetic field warning
Alerte au champ magnétique
CAUTION
Non-ionizing radiation
Rayonnement non ionisant
INFORMATION
INFORMATION
Provides important information on the product, handling or
relevant sections of the documentation, which require particular
attention.
Page 8 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual is
regularly checked and required corrections are included in the subsequent
versions. The machine manufacturer is responsible for the proper
assembly, as well as device configuration. The machine operator is
responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If necessary,
contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product description. It
does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operating
manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
22.02.2022 Page 9

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
2.3 General Safety Guidelines
The Safety Guidelines in the other sections of this operating manual must be observed. These
instructions are visually emphasized by symbols.
INFORMATION
According to EU Guidelines, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of the
machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer of
the product, or its online availability indicated.
Maintain this operating manual in readable condition and keep it
accessible for reference.
This device contains a Li-Ion battery. For this reason, we refer you to the
manufacturer’s specification (battery safety data sheet). This can be found
on our website.
Regarding the requirements for Safety and health connected to the use of
machines, the manufacturer must perform a risk assessment in
accordance with machine guidelines 2006/42/EG before introducing a
machine to the market. Before commissioning this product, check that
conformance with the provisions of the 2006/42/EG guidelines is correct.
As long as the machine with which the product should be used does not
comply with the guideline, operating this product is prohibited.
Operate the unit with devices and accessories approved by SIGMATEK
only.
Page 10 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
CAUTION
Handle the device with care and do not drop or let fall.
Prevent foreign bodies and fluids from entering the device.
The device must not be opened, otherwise it could be damaged!
Manipulez l’appareil avec précaution et ne le laissez pas tomber.
Empêchez les corps étrangers et les liquides de pénétrer dans l’appareil.
L’appareil ne doit pas être ouvert, sinon il risque d’être endommagé!
Regularly check the housing for mechanical damage.
Vérifier régulièrement l’absence de dommages mécaniques sur le boîtier.
The module complies with EN61131-2.
In combination with a machine, the machine builder must comply with EN
60204-1 standards.
For your own safety and that of others, compliance with the environmental
conditions is essential.
The control cabinet must be connected to ground correctly.
To perform maintenance or repairs, disconnect the system from the power
supply.
Le module est conforme à la norme EN61131-2.
En combinaison avec une machine, le constructeur de la machine doit
respecter la norme EN 60204-1.
Pour votre propre sécurité et celle des autres, le respect des conditions
environnementales est essentiel.
L’armoire de commande doit être raccordée correctement à la terre.
Pour l'entretien et les réparations, débranchez le système de
l'alimentation.
INFORMATION
Hardware and software features (application-specific data) can be found
in chapter 17 Application Information.
22.02.2022 Page 11

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
2.4 Software/Training
The application is created with the software LASAL CLASS 2 and LASAL SCREEN Editor.
Training for the LASAL development environment, with which the product can be configured,
is provided. Information on our training schedule can be found on our website.
Page 12 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
3 Standards and Guidelines
3.1 Guidelines
The product was constructed in compliance with the following European Union guidelines and
tested for conformity.
3.1.1 EU Conformity Declaration
EU Declaration of Conformity
The product HGW 1033-01 conforms to the following European guidelines:
2006/42/EG Machine Guideline
2014/30/EU Electromagnetic Compatibility (EMC Guideline)
2014/53/EU Wireless Device Guideline
2011/65/EU “Restricted use of certain hazardous substances in
electrical and electronic equipment” (RoHS Guideline)
The EU Conformity Declarations are provided on the SIGMATEK website.
See Products/Downloads or use the search function and the keyword “EU
Declaration of Conformity”.
22.02.2022 Page 13

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
3.2 Wireless System Operation
INFORMATION
Technical changes to the device (such as different antennae), as well as
improper use can lead to the loss of the FCC license and generate
interference, which can affect the function of nearby devices.
Les changements techniques apportés à l'appareil (comme les différentes
antennes), ainsi qu'une utilisation incorrecte peuvent entraîner la perte de
la licence FCC et générer des interférences, ce qui peut affecter le
fonctionnement des appareils voisins.
Please note the national regulations and standards when operating the
wireless device!
Veuillez respecter les prescriptions et normes nationales lors de
l'utilisation de l'appareil radio !
Page 14 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
4 Technical Data
4.1 Performance Data
Processor EDGE2 Technology
Processor cores 21)
Internal cache 32-kbyte L1 Instruction Cache
32-kbyte L1 Data Cache
512-kbyte L2 Cache
Internal program and
data memory
2048 Mbytes (DDR3 RAM)
Internal remnant
data memory
512-kbyte MRAM
Internal storage device 512-Mbyte microSD card, expandable2)
Internal I/O no
Battery Capacity: 3780 mAh (minimal) Lithium-Ion at 11.4 V
Runtime: > 2 h continuous operation with new battery
Chart/Status display via On/Off button
Charging time < 3 h via USB-C as well as base station at 25 °C
with a rising temperature and active use of the device, the charge time may
increase
Interfaces 1x USB 2.0 Type-A (Host)
1x USB 2.0 Type-C (Dual Role Port,
Charging: USB-PD Profile 4: 20 V, 3 A, 60 W)
1x WLAN Dual-Band (2.4 GHz, 5 GHz simultaneous)
Internal interface connections
and devices
1x TFT color display
1x USB (touch connection)
Control Elements on/off button (illuminated, with application interface)
Display
Resolution
10.1“TFT LCD color display
WXGA 1280 x 800 pixels
Operating field Touch screen (multi-touch, projective capacitive)
1) Attention: When programming (with LASAL) on multicore CPUs, particular focus must be placed on thread security!
2) For safety reasons, the device may only be extended by trained personnel.
22.02.2022 Page 15

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
Status LEDs 2x front (controllable via application)
1x back (boot status/controllable via application)
1x power switch (shows power and charge status)
Signal generator yes (at least 83 dB at 30 cm)
Real-time clock yes (circa 3 days buffered with 100 % charge, ca. 1 day in RTC buffer)
Temperature sensors 4 (2x LP, 1x CPU, 1x battery)
Cooling passive (fanless)
Input voltage measurement yes
4.2 Electrical Requirements
Charging voltage typically +19 V DC
minimum +15 V DC maximum +24 V
Protection class III
Charging current up to 2.5 A at 15.5 V
USB Host current load maximum 0.5 A
INFORMATION
The specified charging time applies to the charging process when the
panel is not simultaneously in use. If the device is in use while charging,
the charging time can increase.
To protect the battery, the intelligent charging circuit monitors the ambient
temperature. For this reason, the charging time can be extended at high
ambient temperatures.
The specified current consumption applies to the status without connected
peripherals (USB stick ...).
Page 16 22.02.2022

WIRELESS HANDHELD OPERATING PANEL HGW 1033-01
4.3 Display
Type 10.1” TFT LCD color display
Resolution WXGA 1280 x 800 pixels
Color depth 18-bit RGB (16.7 million colors)
LCD mode normally black1)
LCD Polarizer transmissive2)
Pixel size 0.1695 x 0.1695 mm
Active range 135.6 (V) x 216.96 (H) mm
Backlighting LED, adjustable
Contrast ratio typically 800:1
Brightness typically 300 cd/m²
Angle CR ≥ 10 85° from all sides3)
Life span By compliance with the ambient conditions, the brightness of the display
sinks after 15,000 operating hours to 50 % of the original brightness.
Due to the manufacturing process, individual pixel errors cannot be excluded to 100 % and therefore do not constitute a
reduction in quality.
1) If there is no display data, the display remains black when the backlighting is on.
2) Display technology, with which display backlighting is used.
3) The viewing angle is measured from the normal to the display surface.
22.02.2022 Page 17

HGW 1033-01 WIRELESS HANDHELD OPERATING PANEL
4.4 Control Unit
Operating field Touch screen (multi-touch, projective capacitive)
Maximum number of fingers 10
The operation with thin gloves yes
SIGMATEK Touch pen (passive) yes
Handwriting recognition no
Ball of the thumb recognition no
Water spray recognition1) yes
Water detection2) no
Cleaning see chapter 14.1 Cleaning and Disinfecting the Touch Screen
INFORMATION
The touch function may still have to be individually adapted to the
respective environmental conditions.
4.5 Input
Input Multi-touch screen (PCAP)
On/off button 1
1) Detects individual water droplets on the touch screen and remains operable.
2) Detects a large amount of water on the touch screen and deactivates it.
Page 18 22.02.2022