Signtex Lighting RAENB-PEN Series Quick start guide

Series RAENB-PEN
Rapier Accessible Exit Sign
Rapier Accessible Exit Master Remote System 07.21.01
INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL
1. Disconnect AC power before servicing.
2. Refer to wiring diagram for proper connections.
3. All servicing should be performed by qualified personnel.
4. Consult your local building code for approved wiring and
installation.
5. Do not use outdoors.
6. Do not use this equipment for other than intended use.
7. Do not let power cords touch hot surfaces.
8. Mount and secure the fixture at a location and height
to avoid ready access and tampering by unauthorized
persons.
9. The use of accessory equipment is not recommended by
the manufacturer and may cause an unsafe condition.
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
HORIZONTAL MOUNT SINGLE FACE
DOUBLE FACE
MASTER
REMOTE
CLASS 2 LOW VOLTAGE WIRING 18-22 AWG
STANDARD DEEP J- BOX
4" x 4" x 2 1/8"
STANDARD DEEP J- BOX
4" x 4" x 2 1/8"
STANDARD DEEP J- BOX
4" x 4" x 2 1/8"
120/277
VAC INPUT
STANDARD 1 1/2”
EXTENSION RING
12 1/8"
VERTICAL MOUNT SINGLE FACE
8 1/4"
120/277
VAC INPUT
STANDARD DEEP
4 X 4 X 2 1/8" J-BOX
1 1/2" EXTENSION
Fig. 1
Fig. 2
J-BOX INSTALLATION
1. See Fig 1: Install a 4” x 4” x 2 1/8” J-box with 1 ½” extension for Master sign and Remote signs. Position J-boxes
approx ¼” below finished panel surface and set in line, 12 1/8” apart for horizontal mount, and 8 ¼” apart for
vertical mount. NOTE- Location of J- boxes must be accurate to position the two signs correctly.
2. See Fig 2: Attach low voltage output wiring to Terminal Block mounted on Master power supply assembly (some
fixtures may be shipped with wiring in place). Maintain color codes and polarities as shown.
3. Connect AC input wiring 120/277 VAC to power supply in Master J-box with standard wire nuts and attach Ground
wire to J-box.
POWER FEED TO
TERMINAL BLOCK
20 AWG
(SUPPLIED)
J- BOX
120/ 277
VAC
SUPPLY
LGN
MASTER SIGN POWER
SUPPLY ASSEMBLY
RED
BLACK
PUSH- WIRE
TERMINAL BLOCK
BACK VIEW
BROWN
BROWN
RED
RED
POWER
SUPPLY
MODULE
TO MASTER
TO REMOTE
MASTER
REMOTE
CLASS 2 LOW VOLTAGE WIRING 18-22 AWG
STANDARD
DEEP J- BOX
4" x 4" x 2 1/8"
120/277
VAC INPUT
STANDARD 1 1/2”
EXTENSION RING
12 1/8"
220 VFW Avenue, Grasonville, MD 21638 P (410)827- 8300 F(410)827- 8866
Signtex Lighting

-2-
PUSH- WIRE
TERMINAL BLOCK
J- BOX 4" x 4"
x 2-1/8"
BY OTHERS
J- BOX
4" X 4" X 2 1/8"
BY OTHERS
12 1/8"
4" ADAPTOR
PLATE
COVER RELEASE SLOT
INSERT 1/4" SCREW
DRIVER, TWIST TO
RELEASE
PENDANT
ADAPTOR
CEILING
OUTPUT TO
REMOTE
18-20 AWG
12-24 VDC
FROM
MASTER
CLASS 2
CONDUCTORS
(BY OTHERS)
BLACK
LAMP PLUG
POLARIZED
2- PIN
Fig. 3
Rapier Accessible Exit Master Remote System
Pendant Mount
J- BOX MOUNT SCREWS
(2) #8-32 X 1/2"
CANOPY TRIM
PENDANT
ADAPTOR
PLATE
PENDANT
PENDANT
SNAP
BACK
COVER
1/2" LOCK NUT
(2) REQ'D
MASTER
TOP VIEW
SIGN INSTALLATION
1. See Fig 3: Remove Back Cover from Master and Remote signs and remove two #6-32 x ¼ Flat Hd screws
attaching CLIP at base of signs DO NOT DISCARD SCREWS.
2. Attach Pendant Assembly to Master and Remote signs, connect lamp plug and position plug in location
shown.
3. Raise each sign assembly into position, connect lamp plug and push connector with excess wire into J-
Box. Attach Canopy Trim to J-Box with (2) #8-32 screws and tighten pendant lock nuts.
4. Attach CLIP at base of sign assembly with (2) flat head screws supplied. As shown, locate the base of each
Back Cover on tabs at base of sign, rotate and snap each cover in place.
5. Turn on AC power to check lamp operation on Master and Remote signs.
YELLOW
LAMP PLUG
LENS
JOINER CLIP
REMOTE
Back Cover Removed
HARDWARE KIT
PROVIDED
(1) 4” ADAPTOR PLATE
for Remote Sign
(2) Four #8-32 x ¾”
Machine Screws
(3) Two Pre-wired Pendant
Assemblies with Canopy
Trim and Pendant Mount
Bracket
120/277VAC
Signtex Inc
LIGHTING
220 VFW Avenue, Grasonville, MD 21638
TEL: (410) 827-- 8300 Fax:[phone]
[e-mail] www.signtexinc.com
Series RAENB-PEN
Rapier Accessible Exit Sign
Rapier Accessible Exit Master Remote System 07.21.01
LED Driver
Power Supply