Sigtronics S-AR User manual

igtronics
®
S
Sigtronics Corporation
178 East Arrow Highway
San Dimas, CA 91773
Phone: [phone]
E-mail: [e-mail]
Web Site: www.sigtronics.com
Model S-AR
Headset Instructions
The S-AR series headsets are adjusted at the factory for immediate use with all current
standard radio systems in general aviation aircraft. Headsets equipped with two plugs are
the standard conguration. The headphone plug is the larger diameter plug and should be
inserted into the headphone jack (.250” standard stereo or monaural jack). The mic plug is
the smaller diameter plug and should be inserted into the microphone jack (.206” standard
microphone jack). The S-AR stereo headset has dual volume controls, a stereo headphone
plug, and a stereo-mono switch for operation with either stereo or monaural systems.
The headband is adjustable through a full range of adult sizes, or the locking nuts may be
tightened to allow you to custom t the headset. Place the headset over your head, adjust
the slides up until minimum pressure is felt on the top of your head. The headset is now
properly adjusted. For maximum noise attenuation, the clamping pressure has been set
at the factory. Releasing the clamping pressure by bending the headband is not advised,
because loss of attenuation will result. Note: If especially small (youth size) or large head-
bands are needed, they may be ordered from Sigtronics.
The microphone boom is fully adjustable and will rotate 180 degrees. For best results use
with the microphone on the left side of the head. Make sure you are speaking into the
side of the mic labeled “Talk” or substantial loss of gain will occur. Microphone place-
ment should be at the corner of the mouth, approximately 1/4” from the lips. Sigtronics
ultra-deep gel ear seals will provide for best performance. Do not insert any material into
the ear cups.
When you rst connect the headset ,make sure the stereo / mono switch is in the proper
position (i.e. in the “MONO” position if plugged in a mono jack or in the “STEREO” position
if plugged into a stereo jack). With the S-AR power plug securely fastened to the battery
box power jack, push the power switch to the ON ( —) position. Turn both volume con-
trols on the headset up to maximum volume. For the mic side volume control, maximum
volume is full clockwise. For the switch side volume control, maximum volume is full
counter-clockwise. Adjust the listening volume with the audio control of either your radio
or intercom as appropriate. Passengers should also turn their individual headset volumes
up fully. Doing this allows for a full range of adjustment for each passenger, since those
with the most acute hearing can turn their headset volume down, if necessary.
continued on back…
Test the headset in the ON ( —) and OFF ( O) modes on the ramp prior to take o. If there is
a problem in the ON ( — ) position then use in the OFF ( O) position. The S-AR is completely
fail-safe and will continue to work even if power to the headset is lost. If the power to the
headset is unstable, simply turn o power and use headset in the OFF ( O) position. The
S-AR performs best when using high quality Alkaline batteries. The life of these high quality
batteries should last 20 hours minimum. To guard against accidentally leaving the power
on, unplug the power cable from the power module when not in use. DO NOT ATTEMPT
TO POWER THE S-AR DIRECTLY FROM YOUR AIRCRAFT electrical system without using
our panel mount power system. This system will give clean stable power to the S-AR.
CLEANING
Headset parts may be cleaned with mild soap on a soft damp cloth. Then dry immediately.
CAUTION: DO NOT immerse any part of the headset in water or any other liquid. Be espe-
cially careful not to allow the microphone to become wet! Exposure to moisture may cause
internal corrosion and failure and will void your manufacturers warranty.
Cleaning will help the headset maintain its “like new ”condition for many years.
WINDSCREEN
The microphone windscreen will reduce annoying wind noise and breath pops picked up
by headset microphones. It also protects the microphone element from dirt and moisture.
The windscreen should be washed regularly to maintain hygiene and avoid clogging. Wash
in warm water and mild soap. Rinse thoroughly and make sure it is completely dry before
putting it back on.
To remove the windscreen, carefully grasp the windscreen lightly along it entire length
and remove from the microphone element being careful not to twist the element itself.
Put the windscreen on the microphone by gently pulling from the open end. Do not pull
it so tightly that it stretches against the end of the microphone.
WARRANTY
Your headset is covered by a limited three-year parts and labor warranty. Please see the
enclosed warranty card for details.
You may refer to the parts list on the reverse side, if you choose to replace parts yourself.
The parts list describes parts for this particular headset only. Parts lists for other models
are available on our Web Site or can be obtained by contacting Sigtronics Corporation.

SIGTRONICS S-AR HEADSET PARTS IDENTIFICATION BREAKDOWN
ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION
1100687 HEAD BAND EXTRUSION, 6.25 IN., S-AR 14 100949 EAR CUP, PRINTED AND DRILLED, MICROPHONE SIDE 27 100569 STRAIN RELIEF, CABLE
2100610 CUSHION, HEADBAND, FOAM FILLED 15 100950 EAR CUP, PRINTED AND DRILLED, SWITCH SIDE 28 100579 CLIP, CLOTHING, HEADSET CABLE
3100602 HEADBAND, METAL, BLACK, STANDARD 16 100049 GROMMET, 5/16 INCH, RUBBER 29 100360 KNOB, BLACK, VOLUME
4100603 YOKE, EAR CUP MOUNT, METAL, BLACK 17 800044 MICROPHONE & FLEX BOOM ASSEMBLY 30 100365 POTENTIOMETER, 2K
5100604 BRACKET, YOKE SUPPORT WITH TANG, BLACK 18 100597 NUT, HEX, 3/8-24, FLEX BOOM ADAPTER 31 100509 SWITCH, STEREO / MONO
6100373 SLIDE, YOKE BRACKET, LONG, NYLON 19 90 0111 WINDSCREEN, MIC, 8 SERIES 32 100508 WASHER
7100258 CLIP, HEADBAND GUIDE, PLASTIC 20 800250 PREAMP 33 100507 NUT, STEREO / MONO SWITCH
8100393 CLIP, ANTI-ROTATION, YOKE, PLASTIC 21 100686 EAR SEAL, GEL / FOAM FILLED 34 100754 RECEIVER MODULE — SWITCH SIDE
9100362 CLIP, CROSS-OVER, WIRE, PLASTIC 22 100684 FOAM, SOUND AT TENUATING 35 100755 RECEIVER MODULE — MICROPHONE SIDE
10 100363 SCREW, 8-32 X 1/2, PHILLIPS HEAD 23 100685 SOUND ATTENUATING, RECEIVER COVER 36 80 0114 POWER MODULE, BATTERY
11 100364 SCREW, 8-32 X 3/8, PHILLIPS HEAD 24 80 0116 CABLE, HEADSET, STEREO 37 10 0179 BATTERY, 9 VOLT
12 100251 E-RING, EAR CUP TO YOKE RETAINER 25 100934 WIRE, CROSSOVER, OVER THE HEAD, 30 INCHES 38 100613 OPTIONAL – HEADBAND, METAL, BLACK, LARGE
13 100252 NUT, HEX, 8-32, LOCKING 26 100935 WIRE, #22, JUMPER, HEADSET, 4 INCH 39 100672 OPTIONAL – HEADBAND, METAL, BLACK, YOUTH























 





 












9-30-2021
P/N 700119
s-ar.pdf