SIIG JU-NE0711-S1 Product information sheet

USB 3.0 to Gigabit
Ethernet Adapter
User Reference Guide
04-1059A
Introduction
The USB 3.0 to Gigabit Ethernet Adapter easily
adds an RJ45 Gigabit Ethernet port to a USB-
enabled system.
Key Features and Benefits
• Adds a reliable wired Gigabit Ethernet port
(RJ45) to your Windows or Mac system
through USB connection
• Supports SuperSpeed USB 3.0 data transfer
rate with high performance packet transfer
rate
• Supports full duplex with flow control and
half duplex with back pressure operation
• SupportsMDI/MDIXauto-crossover,Wake-
on-LAN, IEEE 802.3az (EEE) and Jumbo
Frame

2
Chipset Realtek RTL8153
Host Interface USB 3.0
Connectors USB 3.0 Type-A, Male (Input)
RJ45 Gigabit Ethernet, Female (Output)
Compatible Networks 10/100/1000 Mbps
Power USB Bus-powered
Color Black
Dimensions 2.76" (W) x 0.67" (H) x 1.22" (D)
Weight 0.09lbs (40g)
Specifications
System Requirements
• Desktop or notebook computer with an
available USB port (USB 3.0 recommended)
• Windows®
10 (32-/64-bit) / 8.x (32-/64-bit)
/ 7 (32-/64-bit) / XP (32-/64-bit)
• Windows Server®
2012 R2 / 2012 / 2008 R2
/ 2003 (32-/64-bit)
• Mac OS X®
10.12 to 10.6

3
•USB 3.0 Type-A: Connects to an available
USB port
•RJ 45 Gigabit Ethernet: Connects to a router
via an Ethernet cable (not included)
•Power LED (Red): ON when plugged into a
USB port
Figure 1: USB 3.0 to Gigabit Ethernet Adapter
USB 3.0 Type-A
Power LED
Package Contents
•USB 3.0 to Gigabit Ethernet Adapter
• User Reference Guide
Product Layout
RJ45 Gigabit Ethernet

4
•Connection & Activity LEDs (x2): ON when
connected to a network; blink when network
activity is detected
100Mbps 1000Mbps
Power LED
Note: There's no LED indicator for 10Mbps mode
LED
Indicator
Speed Of
Internet
No LED 10Mbps
Blue
LED 100Mbps
Green
LED 1000Mbps
Windows Installation
Windows 10 / 8.x / XP (32-/64-bit) / Server 2003
These OSes have built-in driver support for this
adapter. Simply plug in the adapter and the driver
will load automatically.
Windows 7 / Server 2012 R2 / 2012 / 2008 R2 (32-
/64-bit)
Note: Windows 7 with the latest service packs
installed, the drivers are built-in. For Windows
7 without service pack or older service packs
installed, please follow the instructions below.

5
1. Insert this adapter to an available USB port
and verify the Power LED is lit.
2. An Autoplay pop-up window will display
automatically and select Run RTK_NIC_
....exe. If not, go to Computer, My Computer
or This PC on the desktop, then select the
CD Drive under Devices with Removable
Storage/ Devices and drives manually.
3. Choose Yes at User Account Control window
(Windows 7 only) and the driver will start
to install.
4. A Program Compatibility Assistant window
will appear which shows ''This program
might not have installed correctly". Select
Cancel to close the window. (It's a warning
only, not a failed installation notice)

6
5. After a successful installation, the below
message should pop up in the notification
area of Windows' desktop.
Figure 3
6. Connect an Ethernet cable (CAT5/5e/6/7)
to this adapter and it's ready to be used.
Windows Verification
1. Right click Computer, My Computer or
This PC on the desktop, and select Manage.
2. Select Device Manager then expand
Network adapters section.
3. Realtek USB GBE Family Controller should
be displayed.
Figure 2

7
Mac OS Installation
1. Insert this adapter to an available USB port
and verify the Power LED is lit. (Mac OS has
built in driver and will load automatically)
2. Connect an Ethernet cable to this adapter
and go to www.siig.com to download the
latest driver. Enter part# JU-NE0711-S1 in
the search box to find this product, select
it, then click Downloads tab and download
the appropriate driver for your OS.
3. Run it and follow the on-screen steps to
update the driver.
4. After restarting, the adapter is ready for use
now.
Mac OS Verification
1. Click on the left-top corner of the taskbar
and choose About This Mac.
2. Choose More Info..., then select System
Report....
3. Expand USB section (under Hardware).
USB 10/100/1000 LAN should be displayed.

8
FAQ & Solutions
1. If the adapter is not working properly:
• Check both connections of the adapter are
firm.
• Make sure the power LED of the adapter is
lit after plugged into the USB port of the
computer.
• Try other USB ports.
• Go to Device Manager to check whether
the driver is installed successfully. (Refer to
Verification for details)
2. The included burn-in driver is basic version.
For details or update, where could I
download the driver?
• Go to www.siig.com/download to
download the driver.

9
Blank Page

10
Blank Page