SIIG JJ-P20511-S3 User manual

1
2-Port Serial 550-Value
Quick Installation Guide
04-0627B
Introducing the 2-Port Serial 550-Value
The 2-Port Serial 550-Value provides two 16550 UART
serial ports which supports data transfer rates up to
16 Mb/s.
Features and Benefits
•Adds 2 RS-232 9-pin serial ports to your PCI enabled
system
•CompliantwithPCILocalBusSpecification,Revision
2.3
•16C550 UART and supports serial data rate up to
16 Mb/s
•Deep FIFOs enable high serial data throughput and
reduce CPU utilization
•Conforms to PCI v2.2 Plug and Play
•Can be installed in 32-/64-bit, 3.3v/5v PCI and
PCI-X slots
•Fullsupport forDOS- andWindows-based software
System Requirements
•Pentium or equivalent computer with an available
PCI slot
•Windows®8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-
/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-
/64-bit) / Server 2008 R2 / 2000 / ME / 98SE / 98 /
95, DOS

2
PackageContents
•SIIG 2-Port Serial 550-Value
• Driver CD
• Quick installation guide
Board Layout
Figure 1: Layout
Serial (S1)
Serial (S2)
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer's reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds.Avoid anycontactwith internalpartsand handle
cards only by their external edges.
1. Turn OFF the power to your computer.

3
2. Unplugthe powercordand removeyourcomputer's
cover.
3. Remove the slot bracket from an available PCI slot.
4. Carefully align the card to the selected PCI slot,
push the board down firmly, but gently, until it is
well seated.
5. Replace the slot bracket screw to secure the card.
6. Replacethe computercoverandreconnect thepower
cord.
Software Installation
This section provides the steps on how to install the
2-Port Serial 550-Value drivers. Pleasemake surethe board
is installed before proceeding with the driver installation.
Windows 8 (32-/64-bit) / 7 (32-/64-bit) / Server
2008 R2
1. Install the board and boot up Windows.
2. Right click Computer, click Manage, click Device
Manager.
3. Insert the driver CD. Close the AutoPlay box if
prompted.
4. Right click PCI Serial Port listed first, click Update
Driver Software.
5. Click Browse my computer for updated software.
For 32-bit: Type D:\32bit, click Next. (Change D: to
match your CD-ROM drive letter)
For 64-bit: Type D:\64bit, click Next. (Change D: to
match your CD-ROM drive letter)
6. At Windows has successfully updated your driver
software, click Close.

4
7. Right click PCI Serial Port, click Update Driver
Software.
8. Repeat steps 5& 6and restart the computer.
Windows Vista (32-bit)
1. At the Found New Hardware window, click Locate
and install driver software (recommended), click
Continue.
2. Click I don't have the disc. Show me other options.
3. Click Browse my computer for driver software.
4. Insert the driver CD. Close the AutoPlay box if
prompted.
5. TypeD:\32bit, clickNext.(Change D:to matchyour
CD-ROM drive letter)
6. At The software for this device has been
successfully installed, click Close to complete the
installation, then restart the computer.
Windows Vista (64-bit)
1. At the Found New Hardware window, click Locate
and install driver software (recommended), click
Continue.
2. Click Don't search online.
3. Click I don't have the disc. Show me other options.
4. Click Browse my computer for driver software.
5. Insert the driver CD. Close the AutoPlay box if
prompted.
6. Type D:\64bit, click Next. (Change D: to match
your CD-ROM drive letter)
7. At The software for this device has been
successfully installed, click Close, then restart the
computer.

5
Windows XP (32-bit)
1. At the Found New Hardware Wizard.
For XP SP2 or later: Select No, not this time, click
Next. Select Install from a list or specific location
(Advanced), then click Next.
For XP SP1 or earlier: Select Install from a list or
specific location (Advanced), then click Next.
2. Insert the driver CD, check Include this location in
the search, uncheck the other box, type D:\32bit,
then click Next. (ChangeD: to match yourCD-ROM
drive letter)
3. Click Finish and restart the computer.
Windows XP (64-bit)
1. Atthe Found New Hardware Wizard, selectNo, not
this time, click Next.
2. Select Install from a list or specific location
(Advanced), click Next.
3. Insert the driver CD, check Include this location in
the search, uncheck the other box, type D:\64bit,
click Next. (Change D: to match your CD-ROM
drive letter)
4. Click Finish and restart the computer.
Windows Server 2003 (32-bit)
1. At the Found New Hardware Wizard.
For Server 2003 SP1 or later: Select No, not this time,
click Next. Select Install from a list or specific
location (Advanced), then click Next.
For Server 2003: Select Install from a list or specific
location (Advanced), then click Next.

6
2. Insert the driver CD, check Include this location in
the search, uncheck the other box, type D:\32bit,
then click Next. (ChangeD: to match yourCD-ROM
drive letter)
3. Click Finish and restart Windows to complete the
installation.
Windows Server 2003 (64-bit)
1. Atthe Found New Hardware Wizard, selectNo, not
this time, click Next.
2. Select Install from a list or specific location
(Advanced), click Next.
3. Insert the driver CD, check Include this location in
the search, uncheck the other box, type D:\64bit,
click Next. (Change D: to match your CD-ROM
drive letter)
4. Click Finish and restart the computer.
Windows Server 2008 (32-bit)
1. At Found New Hardware window, click Locate and
install driver software (recommended).
2. Click Don't search online.
3. Click I don't have the disc. Show me other options.
4. Click Browse my computer for driver software.
5. Insertthe driverCD. TypeD:\32bit, thenclick Next.
(Change D: to match your CD-ROM drive letter)
6. Click Close and restart the computer.
Windows Server 2008 (64-bit)
1. At Found New Hardware window, click Locate and
install driver software (recommended).

7
2. Click Don't search online.
3. Click I don't have the disc. Show me other options.
4. Click Browse my computer for driver software.
5. Insertthe driverCD. Type D:\64bit, thenclick Next.
(Change D: to match your CD-ROM drive letter)
6. Click Close and restart the computer.
Windows 2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), then click Next.
3. SelectSpecify the location, uncheckthe otherboxes,
then click Next.
4. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next, then Finish.
6. Restart the computer.
Windows ME
1. At the Add New Hardware Wizard, choose Specify
the location of the driver (Advanced), then click
Next.
2. Check Specify a location, uncheck the other box,
insert the driver CD, type in D:\ME,then click Next,
Next. (Change D: to match your CD-ROM drive
letter)
3. Click Finish and restart the computer.
Windows 98SE / 98
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommended), then click Next.

8
3. Select Specify a location, uncheck the other boxes,
insertthe driver CD, typeinD:\ME, then clickNext,
Next. (Change D: to match your CD-ROM drive
letter)
4. Click Finish and restart the computer.
Windows 95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD. Click Other Locations.
3. Type D:\ME, click OK, then click Finish. (Change
D: to match your CD-ROM drive letter)
4. At the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in D:\ME,
then click OK to complete the installation.(Change
D: to match your CD-ROM drive letter)
5. Restart the computer.
To Verify Windows Installation
Windows 8 (32-/64-bit) / 7 (32-/64-bit) / Server 2008 R2
1. Right click Computer, click Manage, then click
Device Manger.
2. Double click Ports (COM & LPT), two High-Speed
PCI Serial Port... should be listed.
Windows Vista (32-/64-bit)
1. RightclickComputer, clickManage, clickContinue,
then click Device Manger.
2. Double click Ports (COM & LPT), two High-Speed
PCI Serial Port... should be listed.
Windows XP (32-/64-bit) / Server 2003 (32-/64-bit) / 2000
1. Right click My Computer, click Manage, then click
Device Manger.

9
2. Double click Ports (COM & LPT), two High-Speed
PCI Serial Port... should be listed.
Windows Server 2008 (32-/64-bit)
1. Right click Computer, click Manage, double click
Diagnostics, click Device Manager.
2. Double click Ports (COM & LPT), two High-Speed
PCI Serial Port... should be listed.
Windows ME / 98SE / 98 / 95
1. Right click My Computer, click Properties, click
Device Manager.
2. Double click Ports (COM & LPT), two M65-PCI
Serial Port... should be listed.
DOS
1. Insert the driver CD. From the C:\> prompt, type
copy D:\dos\*.*,and press Enter. (Change D: to
match your CD-ROM drive letter)
2. Type edit autoexec.bat, and press Enter.
3. Add C:\Gemdosin.exe -a -r at the bottom of the
Autoexec.bat file.
4. Go to File, save the changes and exit.
5. Restart your system for the new setup to take effect.

10
Blank Page