SIIG HDMI Over Gigabit IP Distribution System User manual

1
Introduction
The HDMI Over Gigabit IP Distribution System providesan
easy extension of HDMI signal over one Cat5/6 cable up
to 330ft.
Features and Benefits
• Compliant with HDMI, HDCP and DVI standards
• HDMI signal transmission/extension up to 100
meters
• Supports HDTV resolution up to 1080p
• Supports PCM 2 channel audio & IR pass through
• Metal housing for better RF shielding
PackageContents
•HDMIOverGigabitIPDistribution System-Transmitter
• HDMI Over Gigabit IP Distribution System - Receiver
• Power adapter 5V/2.5A (2)
• IR blaster cable & IR receiver cable
• Quick installation guide
04-0870B
HDMI Over Gigabit IP
Distribution System
Quick Installation Guide

2
Layout
Figure 1: Transmitter_Rear
Figure 2: Transmitter_Front
• DC5V: Plug the included power adapter here
• RJ45: Connect to the Receiver's RJ45 port by using a
Cat 5/6 cable (cable not included)
• HDMI IN: Connects to your HDMI source device
using an HDMI cable (cable not included)
• IR Emitter: Connect the IR blaster cable here
• Power LED: On when power adapter is connected
• Link LED: On when RJ45 connection is established
• DIPSwitch:When there're morethan1inputsources,
select your source channel through DIP switch
• Reset: Press and hold down the reset button for 5
seconds to go back to the factory default settings
RJ45 HDMI IN
DC5V
IR Emitter
DIP Switch Link LED
Power LED
Reset

3
Figure 4: Receiver_Front
Figure 3: Receiver_Rear
DC5V RJ45
HDMI
OUT
• DC5V: Plug the included power adapter here
• RJ45: Connects to the Transmitter's RJ45 port using
a Cat 5/6 cable (cable not included)
• HDMI OUT: Connects to your HDMI display using
an HDMI cable (cable not included)
• Reset: Press and hold the reset button for 5 seconds
to go back to the factory default settings
• Power LED: On when power adapter is connected
• Link LED: On when RJ45 connection is established
• IR: Connect the IR receiver cable here
• DIPSwitch: Whenthereare morethan1inputsources,
select your source channel through DIP switch
DIP Switch
Link LED
Power LED
IR
Reset

4
IR Extension Cables
IR Blaster Cable:
Connect the IR blaster cable to your Transmitter's IR
Emitter connector to send out IR command signals, if
needed.
Figure 5
IR Receiver Cable:
Connect the IR receiver cable to your Receiver's IR
connector to receive IR command signals, if needed.
Figure 6

5
Table 1
󳚿󳛛󳛡󳛞󳛏󳛑
󳛏󳛔󳛍󳛚󳛚󳛑󳛘󳚯󳛛󳛙󳛎󳛕󳛚󳛍󳛠󳛕󳛛󳛚 󳚔󳚿󳛣󳛕󳛠󳛏󳛔󳚌󳚝󳚙󳚠󳚕
󳚿󳛛󳛡󳛞󳛏󳛑
󳛏󳛔󳛍󳛚󳛚󳛑󳛘󳚯󳛛󳛙󳛎󳛕󳛚󳛍󳛠󳛕󳛛󳛚 󳚔󳚿󳛣󳛕󳛠󳛏󳛔󳚌󳚝󳚙󳚠󳚕
󳚝 󳚜󳚜󳚜󳚜 󳚥 󳚜󳚝󳚝󳚝
󳚞 󳚜󳚜󳚜󳚝 󳚝󳚜 󳚝󳚜󳚝󳚝
󳚟 󳚜󳚜󳚝󳚜 󳚝󳚝 󳚝󳚜󳚜󳚝
󳚠 󳚜󳚝󳚜󳚜 󳚝󳚞 󳚜󳚝󳚝󳚜
󳚡 󳚝󳚜󳚜󳚜 󳚝󳚟 󳚜󳚜󳚝󳚜
󳚢 󳚝󳚝󳚜󳚜 󳚝󳚠 󳚜󳚝󳚜󳚝
󳚣 󳚜󳚜󳚝󳚝 󳚝󳚡 󳚝󳚝󳚜󳚝
󳚤 󳚝󳚝󳚝󳚜 󳚝󳚢 󳚝󳚝󳚝󳚝
* "0" means remain the switch down; "1" means bend the switch up to ON
**
DIP Switch
Adjust your DIP switch to select the source channel.
There are 16 combinations; that is, you can connect at
most 16 transmitters at the same time.
Refer to Figure 7 for the position of switch 1-4, and refer
to Table 1 for all the 16 combinations.
Figure 7

6
Hardware Installation
1. Power off all devices, including the HDMI source
device and HDMI display.
2. ConnectyourHDMI source(suchasa Blu-rayplayer)
to the Transmitter's HDMI IN connector.
3. Connect your HDMI display (such as a LCD TV) to
the Receiver's HDMI OUT connector.
4. Connect the IR extension cables to the IR blaster and
IR receiver connector on the Transmitter and
Receiver respectively.
Skip this step if IR transmission is not needed.
5. To connect Transmitter and Receiver directly: Connect
your CAT5/6 LAN cable between the Transmitter
and Receiver. Make sure your Cat5/6 LAN cable is
securely connected and not loose.
To connect Transmitter andReceiver indirectly: Connect
theTransmitterto the inputportofaGigabit Ethernet
hub by using a Cat5/6 LAN cable, then connect the
Receiver to the output port of the Gigabit Ethernet
hub by using another Cat5/6 LAN cable.
6. Plug one of the included power adapters into the
DC5V powerjackofthetransmitter,plugthesecond
power adapter into the DC5V power jack of the
receiver,thenplugbothpoweradaptersintoreliable
power sources.
7. After the transmitter and receiver are connected, the
HDMI extender is ready for use.

7
Application
One Transmitter to One Receiver
Connect Transmitter and Receiver Directly
Figure 8

8
Connect Transmitter and Receiver Indirectly
Figure 9
NOTE:ThelengthofCat5/6cablebetweenGigabit
switch/hub and Transmitter/Receiver can be up
to 100m each.

9
Figure 10
One Transmitter to multiple Receivers
• One Transmitter can connect to up to 200 Receiver
units
• The HDMI Over Gigabit IP Distribution System only
can be used with Gigabit Ethernet switch/hub

10
Figure 11
Multiple Transmitters to multiple Receivers
• The DIP switch has 16 combinations, which means
up to 16 Transmitters can be connected at the same
time
• Adjust the DIP switch on Receiver to be the same as
the DIP switch on the desired source channel's
Transmitter
• The HDMI Over Gigabit IP Distribution System only
can be used with Gigabit Ethernet switch/hub

11
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support has answers! Simply visit our web site
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be
just a few clicks away. You can also submit questions online and a technical
support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any
defects in materials or workmanship for three (3) years from the date of
purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective in
materials or workmanship. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. Please see our
web site for more warranty details.
Ifyou encounter any problems with this product, pleasefollowtheprocedures
below.
A) If it is within the store's return policy period, please return the product to
the store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow
these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support,
then Request A Product Replacement to submit a request to SIIG RMA
or fax a request to 510-657-5962. Your RMA request will be processed, if
the product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s) and any
otheraccessories that came with the original package must beincluded.
•Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted
on the outside of the shipping carton.
•You are responsible for the cost of shipping to SIIG. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground in the U.S.
and International Economy outside of the U.S. at no cost to the
customer.

About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. Allcentered around the distribution and switchingofA/Vsignals
overCAT5/6,theseproductsincludematrixswitches, distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
PRODUCT NAME
HDMI Over Gigabit IP Distribution System
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
HDMI Over Gigabit IP Distribution System is a trademark of SIIG, Inc. SIIG and the SIIG logo are
registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft
Corporation. Allothernamesusedin thispublicationare foridentificationonly andmaybe trademarks
oftheir respective owners.
August, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.