Silent Witness SWX80 User manual

SWX80, SWX81, and
SWX82 Night Hawk®
CCD Camera User Guide
A Honeywell Company

Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Connect Video and Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 2: Attach the Camera Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Flush Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Flush and Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 3: Position the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 4: Adjust the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dip Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjustment Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjust the Focus and Iris Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjust the Line Lock (Vertical Phase) for 24 VAC Operation . . . . . . . . 8
Adjust the Backlight Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SWX80 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SWX81 and SWX82 Technical Specifications . . . . . . . . . . . . . . . . . . . . 10
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FCC Statement (U.S.A.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Industry Canada Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Π. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Europe and United Kingdom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mounting Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1
Overview
The SWX80, SWX81, and SWX82 Night Hawk® CCD cameras provide true 24/7
surveillance. These small, discreet cameras take perfectly exposed pictures no
matter what the lighting conditions.
The SWX81 and SWX82 cameras have built-in, infrared LED illuminators to
improve low light viewing. The SWX81 camera has 18 near-infrared light emitting
diodes that provide short-range illumination. The SWX82 has 48 near-infrared light
emitting diodes for longer-range illumination.1
The bullet style, track mount design incorporates a rugged, high impact aluminum
housing that is weather tight. Locking security screws and concealed wiring ensure
they are tamper and vandal resistant. These cameras are ideally suited for medium
security installations, either indoors or outdoors.
Important Safeguards
Installation and servicing should be done by certified technicians to conform to all
local codes and to maintain your warranty.
1.Night performance illumination differs between camera models: 40 feet (12 m) for
the SWX81 and 75 feet (23 m) for the SWX82. These ranges are approximate; actual
results depend on reflectivity of the scene, weather conditions, and so on.
that important operating
electric shock is present
ctions accompany
This symbol indicates
and maintenance
instru
this unit.
This symbol indicates
that dangerous voltage
constituting a risk of
within this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION

Document 900.0255 Rev 1.00 June 9, 2004
2
Before You Begin
Unpack Everything
Check that the items received match those listed on the order form and packing
slip. The SWX80/SWX81/SWX82 packing box should include, in addition to this
User Guide:
• One fully assembled camera with factory installed video/power cable
• One hardware kit
If any parts are missing or damaged, contact the dealer you purchased the camera
from or call Silent Witness Customer Service.
Equipment Required
• A Phillips screwdriver may help you complete the installation.
• Mounting screws are not supplied. Use mounting screws appropriate to your
particular installation.The holes on the mounting plate are 3/16 inch in
diameter. See “Mounting Templates” on page 14.
Please read this guide carefully before
you install the SWX80, SWX81, or
SWX82 camera. Keep this guide for
future reference.

3
Installation
The SWX80/SWX81/SWX82 cameras are designed for installation on a wall, ceiling,
or on top of a pole. They are weather sealed for indoor or outdoor locations.
Step 1: Connect Video and Power
Follow Figure 1 for the wiring connection.
Figure 1 Wiring Connection
Note IR LEDs may not function correctly if the power supply is
connected in reverse polarity. To ensure proper IR LED function,
check that power is connected properly. For a DC power
supply, the red wire must be connected to positive and the
black wire must be connected to negative, otherwise the LEDs
on the SWX81/SWX82 will not turn on.
Step 2: Attach the Camera Base
Flush Mount
Drill a hole equal to the diameter of the camera base into the wall or ceiling where
you are connecting the camera. Run the power and video connections through the
wall to their destinations. Be sure to screw the camera into something solid on a
flat, smooth surface (for example, a crossbeam).
WARNING!
The use of a CSA Certified/UL Listed Class 2
power supply is required to ensure
compliance with electrical safety standards.
BNC Jack
Video
Black -
Red +
12 VDC or
24 VAC Input

Document 900.0255 Rev 1.00 June 9, 2004
4
Flush and Surface Mount
1. Loosen, but do not remove the security (locking) screws on the lower and
upper locking rings (see Figure 2).
2. Loosen the lower and upper locking rings to access the mounting screw holes.
Once the locking ring is loosened you can adjust the camera position for easier
access to the four mounting screw holes.
3. Screw the camera base to the desired position on the wall, ceiling, or top of
pole. Use four screws appropriate to your installation to mount the camera.
Note See page 14 for the SWX80 and SWX81 mounting template and
page 15 for the SWX82 mounting template.
Make sure the camera is mounted on a flat, smooth surface.
For Surface Mounting only: To ensure a waterproof installation, the notch
in the camera base that the power and video connections exit through should
be facing down. If the power and video connections exit the top of the base
(wall mounted only), water may pool in the camera base. Apply appropriate
sealant around the notches and any other gaps between the camera base and
the mounting surface.
Step 3: Position the Camera
Caution Do not swivel and position the camera without the bezel
firmly in place. Avoid handling the camera board or lens to
position the field of view as this may damage the camera.
1. Loosen the security screws on the lower and upper locking rings.
2. Loosen the locking rings and move the camera into position. Swivel the camera
to capture the desired field of view. Tighten the locking rings to set the
position.
3. Lock the camera into position using the Allen key supplied to tighten the
locking screws on the locking rings.
Step 4: Adjust the Camera
Note If necessary, adjust the camera after it is mounted firmly in
position. Any new changes to the camera position may require
further adjustment of the zoom and focus.
1. Loosen, but do not remove, the three security (locking) screws on the bezel
with the Allen key supplied (see Figure 2).
One security screw is located under the sunhood. This screw is accessible
through the sunhood by removing the small, black, rubber plug.

5
2. Carefully pull the bezel towards you until it is clear of the camera.
Note The bezel and camera fit closely together and separating them
may require using a little force. Be sure to pull the camera
straight out of the bezel. After the camera starts to slide out,
the airtight seal will break and the camera then slides out easily.
3. Set the bezel and camera down in a place where the tempered glass window
cannot be scratched.
Figure 2 Camera Side View
4. Your camera comes set up from the factory. If you need to make minor
adjustments, refer to the procedures below to adjust the switch settings, iris
level, focus, and vertical phase (24 VAC).
Caution Silent Witness does not recommend changing the dip
switches other than the vertical phase and focus controls.
These dip switches are factory configured for optimal
performance. If further adjustments are required please
feel free to contact Silent Witness Customer Service or
authorized service personnel.
Caution During the entire time the bezel is off, ensure that the
camera board, lens, and LEDs are kept intact and free from
dust.
5. Slide the bezel enclosure over the camera and rotate the enclosure until it
slides into place. Tighten the security screws with the Allen key supplied, to
keep the bezel in place.
Security screws (x3)
SWX82 only
Ring locking screws
Upper locking ring
Camera base
Balls and
sockets for
easy swiveling
and locking
Bezel
Lower locking ring

Document 900.0255 Rev 1.00 June 9, 2004
6
Figure 3 Camera Board
Dip Switch Functions
Figure 4 Factory Default Settings
Adjustment Method
Switch
no.
Function Off On
1 Auto White Balance AWB ATW
2 AGC Off On
3 IRIS Control Electronic IRIS Mechanical IRIS
4 BLC (Backlight
Compensation)
Off On (center window)
5 FLON (Flicker less) Off On
Line lock controls
push buttons
Iris level
adjustment
Top locking
screw adjusts
focus
Bottom locking screw
adjusts focal length
12345
ON
OFF
Legend
1. AWB/ATW
2. AGC
3. IRIS
4. BLC
5. FLON

7
Adjust the Focus and Iris Level
Caution IR LEDs could be warm after prolonged use.
1. If you have not already done so, remove the camera from the bezel (see “Step
4: Adjust the Camera” on page 4).
2. To adjust the focal length, loosen the top locking screw on the side of the lens.
It is marked: ←Far Near →(see Figure 3, page 6, or Figure 5, page 7). Slide the
screw to adjust the focal length.
Figure 5 Varifocal Lens
3. To adjust the focus, loosen the bottom locking screw on the side of the lens. It
is marked: ←Wide Tele →(see Figure 3 or Figure 5). Slide the screw to adjust
the focus.
4. When satisfied with your adjustments, retighten both the locking screws and
replace the camera inside the bezel. See “Step 3: Position the Camera” on
page 4.
Top locking screw
adjusts focus
Bottom locking
screw adjusts focal
length

Document 900.0255 Rev 1.00 June 9, 2004
8
Adjust the Line Lock (Vertical Phase) for 24 VAC
Operation
Phase adjustment may be necessary in multiple camera installations to prevent
picture roll when switching between cameras. To adjust the vertical phase while
switching between two cameras, push down the left or right switch on one camera
until there is no vertical roll (see Figure 3).
Note If the phase cannot be adjusted to prevent picture roll, reverse
the power polarity.
Adjust the Backlight Compensation
The backlight compensation (BLC) adjusts the electronic shutter speed of the
camera based on the light levels in specific areas of the scene. This adjustment
provides better image quality for scenes that are unevenly lit.
The BLC factory default setting is OFF (see Figure 4).
Precautions
The light emitted from the near-infrared light emitting diodes provides illumination
over a wide area. This light is not considered a risk to the unshielded human eye.
However, as with any light source, it is recommended that normal precautions be
taken to avoid unnecessary exposure. For example, avoid staring into the beam or
viewing directly with optical instruments at close range.
Note IR LEDs could be warm after prolonged use.

9
Specifications
SWX80 Technical Specifications
Camera Color True Day/Night
Standard Res High Res Standard Res High Res
NTSC SWX80C100 SWX80C600 SWX80D100-T2 SWX80D600-T2
PAL SWX80C2100 SWX80C2600 SWX80D2100-T2 SWX80D2600-T2
Imager format 1/3 in. CCD Imager Sensor
S/N ratio Better than 50 dB
Video output 1 V p-p; Coax: 75 Ω
Electronic IRIS/
Mechanical IRIS
1/60 (1/50) to 1/100,000 (1/100,000) sec
Sync system 12 VDC: Internal 24 VAC: External (VD lock)
AGC control Selectable On/Off; Factory default is “On”
Backlight
compensation
On (central window) off - switchable;
Factory default is “Off”
Auto white
balance
AWB/ATW; Factory default is ATW
Gamma
correction
0.45
Input voltage 11 - 16 VDC regulateda; 17 - 32 VAC
Surge
suppression
1.5 kW transient
Current
consumption SWX80C100 SWX80C600 SWX80D100-T2 SWX80D600-T2
12 VDC
24 VAC
240 mA
60 Hz, 240 mA
210 mA
60 Hz, 200 mA
240 mA
60 Hz, 220 mA
SWX80C2100 SWX80C2600 SWX80D2100-T2 SWX80D2600-T2
12 VDC
24 VAC
240 mA
50 Hz, 240 mA
210 mA
50 Hz, 200 mA
240 mA
50 Hz, 220 mA
Recommended
power supply
PSI 4.1–DC or
PSA 2420–AC
Resolution 350 TV lines 480 TV lines 350 TV lines 480 TV lines

Document 900.0255 Rev 1.00 June 9, 2004
10
SWX81 and SWX82 Technical Specifications
Light sensitivity
(@ F1.5)
0.6 lux 0.75 lux 0.15 lux 0.2 lux
Lens 4.0–9.0 mm varifocal autoiris, F1.5
Operating
temperature
-13°F to 122°F (-25°C to 50°C)
Relative
humidity
Up to 85%
Enclosure Polished aluminum with sunhood
Dimensions Length: 4.44 in. (112.7 mm)
Diameter: 2.76 in. (70 mm)
Weight 1.25 lbs (0.56 kg)
a. Silent Witness recommends using 15 VDC.
Camera SWX81 with 18 IR LEDs SWX82 with 48 IR LEDs
True Day/Night True Day/Night
Standard Res High Res Standard Res High Res
NTSC SWX81D100-18 SWX81D600-18 SWX82D100-48 SWX82D600-48
PAL SWX81D2100-18 SWX81D2600-18 SWX82D2100-48 SWX82D2600-48
Imager format 1/3 in. CCD Imager Sensor
S/N ratio Better than 50 dB
Video output 1 V p-p; Coax: 75 Ω
Electronic IRIS/
Mechanical IRIS
1/60 (1/50) to 1/100,000 (1/100,000) sec
Sync system 12 VDC: Internal 24 VAC: External (VD lock)
AGC control Selectable On/Off; Factory default is “On”
Backlight
compensation
On (central window) off - switchable; Factory default is “Off”
Auto white
balance
AWB/ATW; Factory default is ATW
Gamma
correction
0.45
Camera Color True Day/Night

11
Input voltage 11–16 VDC regulateda; 17–32 VAC
Surge
suppression
1.5 kW transient
Current
consumption
SWX81D100-18 SWX81D600-18
With IR LEDs On
SWX82D100-48 SWX82D600-48
With IR LEDs On
12 VDC b
24 VAC
380 mA
60 Hz, 320 mA
400 mA
60 Hz, 330 mA
810 mA
60 Hz, 390 mA
850 mA
60 Hz, 420 mA
SWX81D2100-18 SWX81D2600-18 SWX82D2100-48 SWX82D2600-48
12 VDC
24 VAC
380 mA
50 Hz, 320 mA
400 mA
50 Hz, 330 mA
810 mA
50 Hz, 390 mA
850 mA
50 Hz, 420 mA
Note The current consumption is less when the IR LEDs are off
than when the IR LEDs are on.
Recommended
power supply
PSI 4.1–DC or
PSA 2420–AC
PSI 5.1–DC or
PSA 2420–AC
Resolution 350 TV lines 480 TV lines 350 TV lines 480 TV lines
Lightsensitivity/
Minimum
illumination
Zero lux; operates in complete darkness
IR LEDs 850 nm, 18 LEDs 850 nm, 48 LEDs
IR sensitivity 800–1000 nm (with illuminators on)
Lens 4.0–9.0 mm varifocal autoiris, F1.5
Operating
temperature
-13°F to 122°F
(-25°C to 50°C)
-13°F to 104°F
(-25°C to 40°C)
Relative
humidity
Up to 85%
Enclosure Polished aluminum with sunhood
Dimensions Length: 4.44 in. (112.7 mm)
Diameter: 2.76 in. (70 mm)
Length: 5.61 in. (142.5 mm)
Diameter: 3.86 in. (98 mm)
Weight 1.25 lbs (0.57 kg) 2.8 lbs (1.27 kg)
a. Silent Witness recommends using 15 VDC.
b. If DC supply is used, verify the polarity is correct. + goes to +, - goes to -.
Camera SWX81 with 18 IR LEDs SWX82 with 48 IR LEDs

Document 900.0255 Rev 1.00 June 9, 2004
12
Regulatory Compliance
FCC Statement (U.S.A.)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received including interference that may
cause undesired operation.
Industry Canada Notice
This digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique respecte toutes les exigences du Règlement sur la matériel
brouilleur du Canada.
Œ
The Πmark on the product indicates that the system has been tested to, and
conforms with, the provisions noted within the 89/336/EEC Electromagnetic
Compatibility Directive.

13
Warranty and Service
North America
Silent Witness warrants the SWX80, SWX81, and SWX82 against defects in
workmanship and materials for a period of 2 years. During the warranty period
Silent Witness will repair or replace, at its sole option, free of charge, any defective
product returned prepaid.
In the event you have a problem with any Silent Witness product, please call
Customer Service for assistance or to request a Return Authorization (RA)
number.
In the U.S.A. and Canada, call 1.800.893.9513.
Be sure to have the model number, serial number, and the nature of the problem
available for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items
shipped to Silent Witness without a clearly identified Return
Authorization (RA) number may be refused.
Europe and United Kingdom
For warranty information please contact Silent Witness at +1.604.574.1526 or toll
free at 00.800.2020.8080.

Document 900.0255 Rev 1.00 June 9, 2004
14
Mounting Templates
Figure 6 Mounting Template (SWX80/SWX81 shown)
See “Step 2: Attach the Camera Base” on page 3 for information on using the
mounting template.
Note The camera enclosure should be mounted on a flat, smooth
surface.
Mounting screw
holes (3/16 inch
diameter)
When printing this template,
make sure you uncheck Fit to Page
in your Printer options.
This will avoid distortion.

15
Figure 7 Mounting Template (SWX82)
See “Step 2: Attach the Camera Base” on page 3 for information on using the
mounting template.
Note The camera enclosure should be mounted on a flat, smooth
surface.
Mounting screw
holes (3/16 inch
diameter) When printing this template,
make sure you uncheck Fit to Page
in your Printer options.
This will avoid distortion.

A Honeywell Company
Sales: 1.888.289.2288 6554 - 176th Street
Tech Service:1.800.893.9513 Surrey, B.C. V3S 4G5
Phone: [phone] Canada
Fax: [phone]
Email: [email protected]
For the most current product and software download information, visit
www.silentwitness.com/support/.
Document 900.0255 Rev 1.00 June 9, 2004
Specifications subject to change without notice.
Imperial conversions are approximate.
Night Hawk® and Silent Witness® are registered trademarks of Honeywell International
Inc. © 2004 Honeywell International Inc. All rights reserved. Printed in Canada.
www.silentwitness.com
Toll free: 1.888.289.2288
International toll free: 00800.2020.8080