Silhouette DIM32D1BSSPR Assembly instructions

s.01.
OWNER’S USE AND
GUIDE D’UTILISATION
ET SOIN DE PROPRI-
CAUTION
Read and follow all safety rules
and operating instructions
before first use of this product.
PRÉCAUTION
Veuillez lire attentivement les
consignes de sécurité et les
instructions d’utilisation avant
l’utilisation initiale de ce produit.
Danby Products Limited, Guelph, Ontario Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio USA 45840
1-844-455-6097
CARE GUIDE
ÈTAIRE
GUÍA DE UTILIZACIÓN
Y CUIDADO PARA EL
PROPIETARIO
PRECAUCIÓN
Lea y observe todas las reglas
de seguridad las instrucciones
de operación antes de usar esto
producto por primera vez.
DIM32D1BSSPR
2015.06.17

Silhouette 08212014
1-844-455-6097
DO NOT RETURN THIS UNIT TO
THE RETAILER WITHOUT FURTHER
INSTRUCTIONS
Dear Valued Customer: We hope your Silhouette appliance fullls all of your entertaining
needs. Your satisfaction is our priority. Please contact our Customer Care Center toll-free
via 1.844.455.6097 for any inquiries you may have about your new purchase.
NE PAS RETOURNER CET APPAREIL
AU DÉTAILLANT JUSQU’À NOUVEL
ORDRE
Cher client : nous espérons que votre appareil Silhouette répond adéquatement à tous vos
besoins de divertissement. Notre prioritéétant de vous satisfaire, si vous avez des questions
ou des préoccupations relativement à votre nouvelleacquisition, veuillez communiquer avec
notre Centre de service à la clientèle au numéro sans frais 1.844.455.6097.
NO DEVUELVA ESTA UNIDAD AL
VENDEDOR SIN ANTES RECIBIR
INSTRUCCIONES ADICIONALES
Estimado cliente: Esperamos que su aparato “Silhouette” pueda satisfacer todas sus
necesidades. Su satisfacción es nuestra prioridad. Por favor, póngase en contacto con
nuestro Centro de Atención al Cliente al número gratuito 1.844.455.6097, para cualquier
consulta o pregunta que usted pueda tener acerca de su nueva compra.

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF
PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE
REFERENCE.
---------------------------------------------------------------------------------------------------------------
POUR OBTENIR LE SERVICE SUR GARANTIE VOUS DEVEZ FOURNIR UNE
PREUVE D’ACHAT VALIDE. S’IL VOUS PLAITAGRAFE VOTRE REÇU A CETTE
PAGE POUR LA REFERENCE FUTURE.
----------------------------------------------------------------------------------------------------------------
PARA OBTENER SERVICIO DE GARANTÍA, DEBE PROVEER UN RECIBO
ORIGINAL. POR FAVOR ENGRAPE SU RECIBO A ÉSTA PÁGINA EN CASO QUE
NECESITE HACER UN RECLAMO.
This machine is intended to produce ice only. It is not intended for the
long-term storage of ice. Move any excess ice into a freezer for long-
term storage (>6 hours) if you desire to keep it. Ice that is left to sit in
the bucket will melt over time.
IMPORTANT
Cette machine a été conçue pour produire de la glace seulement.
Elle ne doit pas être utilisée pour stocker de la glace à long terme.
Déplacez la glace en surplus dans un congélateur pour un stockage
à long terme (>6 heures) si vous désirez la garder. La glace qui reste
dans le seau fondra.
IMPORTANT
IMPORTANTE
Esta má quina está diseñada para producir solamente hielo. No está
diseñada para almacenar hielo a largo plazo. Traslade el hielo sobran-
te a un congelador para almacenarlo a largo plazo (más de 6 horas) si
desea conservarlo. El hielo que quede en la cubeta se derretirá con el
tiempo.

CONTENTS
TABLE DES MATIÈRES
BUILT IN ICE MAKER
Owner’s Use and Care Guide ..........................................1-10
• Welcome
• Important Safety Information
• Installation Instructions
• Operation Instructions
• Care and Maintenance
• Troubleshooting
• Warranty
MACHINE À GLAÇONS
Guide d’utilisation et d’entretien du propriétaire..........11-20
• Bienvenue
• Consignes de sécurité importantes
• Consignes d’installation
• Consignes d’utilisation
• Soins et entretien
• Dépannage
• Garantie
EQUIPO PARA FABRICAR HIELO
Guía de utilización y cuidado para el propietario.........21-30
• Bienvenido
• Información importante sobre seguridad
• Instrucciones de instalación
• Instrucciones de funcionamiento
• Cuidado y mantenimiento
• Solución sugerida
• Garantía
Model • Modèle • Modelo
DIM32D1BSSPR
CAUTION:
Read and follow all safety rules and operating
instructions before first use of this product.
PRÉCAUTION :
Veuillez lire attentivement les consignes de
sécurité et les instructions d’utilisation avant
l’utilisation initiale de ce produit.
PRECAUCIÓN:
Lea y observe todas las relgas de seguridad y
las instrucciones de operación antes de usar
este producto por la primera vez.
ÍNDICE
Volts / Hertz / Amps / Watts 115V 60Hz 2.6A 240W
Volts / Hertz / Ampères / Watts 115V 60Hz 2.6A 240W
Volts / Hertz / Amperios / Vatios 115V 60Hz 2.6A 240W
• Makes up to 32 lbs daily / ice box capacity is 25 lbs
• Produit jusqu’à 32 lb par jour / capacité de la glacière e 25 lb
• Produce hasta 32 lb al día / la capacidad de la caja de hielo es de 25 lb

1
Thank you for choosing Silhouette
We know you’re excited. We are too! However, the more familiar you are with your new appliance, the better experience you will
have. We therefore strongly suggest that you read this Owner’s Manual before plugging in your new appliance. It contains
important operational information that will help you make full use of the technical features available in your appliance. The
manual also contains information designed to enhance operating reliability and safety, as well as tips to maintaining your new
appliance so that it brings you happiness for years to come.
Please visit www.silhouetteappliances.com to access self-service tools, FAQs and more. Should you need additional assistance,
please call 1-844-455-6097.
Note: You will need the below information to obtain service under warranty.
To receive service, you must provide the original receipt.
Model Number:
Serial Number:
Date of Purchase:
NEED HELP?
Before you call for service, here are a few things you can do to help us serve you
better:
Read this Owner’s Manual:
It contains instructions to help you use and maintain your appliance properly.
If you received a damaged appliance:
Immediately contact the retailer (or builder) that sold you the appliance.
Save time and money:
Check the Troubleshooting section at the end of the guide before calling. This section
helps you solve common problems that may occur.
If you do need service, you can relax, knowing help is only a phone call away.
Tel: [phone]

IMPORTANT SAFEGUARDS
READ ALL SAFETY INFORMATION BEFORE USING
GROUNDING INSTRUCTIONS
• This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
• This appliance is equipped with a power cord that has a grounding wire and grounding plug. The plug must be
plugged into an outlet that is properly installed and grounded.
• Consult a qualified electrician or service technician if the grounding instructions are not completely understood, or
if doubt exists as to whether the appliance is properly grounded.
• If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.
• Plug the unit into an exclusive, properly installed grounded wall outlet.
• Do not under any circumstances cut or remove the third (ground) prong from the power cord.
• Do not use an adapter plug with this appliance.
• Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or
service technician install an outlet near the appliance.
SAVE THESE INSTRUCTIONS!
An empty ice maker is a very dangerous attraction to children. Remove either
the gasket, latches, lock and/or doors from unused or discarded appliances,
or take some other action to guarantee it harmless. DON’T WAIT, DO IT NOW!
WARNING: RISK OF CHILD ENTRAPMENT!
To avoid installation/operation difficulties, refer to
separate installation guide.
WARNING
Improper use of the grounding plug can result in a risk of electric shock.
WARNING
When installing the unit DO NOT kink the drain
hose!
IMPORTANT
2

GROUNDING INSTRUCTIONS
• Do not operate this appliance if it has a damaged power cord or plug, if it is not working properly, or if the appli-
ance has been damaged or dropped.
• Never allow children to operate, play with, or crawl inside the appliance.
• Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.
• Do not store or use gasoline or any other flammable vapors or liquids in the vicinity of this or any other appliance.
The fumes can create a fire hazard or explosion.
• Do not splice the power cord that is equipped with this appliance.
• Keep power cord away from heated surfaces.
• Do not immerse power cord plug or the appliance itself in water.
• Do not use this product near water, for example in a wet basement or near a sink.
• Do not use corrosive chemicals or vapors in this appliance.
• Use this appliance only for its intended use, as described in this manual.
• See door surface cleaning instructions in the Care and Cleaning section(s) of this manual.
• Do not cover or block any openings on the appliance.
• This appliance is intended for household use only. Do not attempt to operate or store this appliance outdoors.
• This appliance should be serviced only by qualified service personnel. Contact the nearest authorized service
facility for examination, repair or adjustment.
It is environmentally damaging to release many types of refrigerant into the atmosphere. Inten-
tionally venting HCFC, CFC, or HFC refrigerant is illegal and punishable by law. Do not tamper
with any of the refrigerant-containing components of this appliance. Ensure that you are following
municipal bylaws when disposing of this or any other refrigeration appliance.
WARNING
IMPORTANT SAFEGUARDS
READ ALL SAFETY INFORMATION BEFORE USING
SAVE THESE INSTRUCTIONS!
3

OPERATING INSTRUCTIONS
CONTROLS OF THE ICE MAKER
The ice maker should be placed where the ambient temperature is between 10-32°C (50-90° F). If the ambient tem-
perature is above or below this range, the performance of the unit may be affected.
Check the water supply
1. Turn off water supply.
2. Disconnect water supply line from the ice maker.
3. Position water supply line in a bucket.
4. Turn on water and make sure water pours into the bucket.
5. Turn water supply off again, then reconnect the water sup-
ply line to the ice maker.
*If unsure, please contact your local plumber.
Control Type Action Function Explanation
Button
Button
Button
Button
Press
Press
Press
Press
To turn the ice mak-
er on/off (press and
hold this button for
approximately 3 seconds)
Small ice
Medium ice
Large ice
Single Indicator light
Single Indicator light
Single Indicator light
Single Indicator light
Simultaneous
Indicator lights
Simultaneous
Indicator lights
ON
FLASHING
ON
All on at the
same time
ON
FLASHING
ON
FLASHING
OFF
2 sizes flashing at the
same time for 15
seconds
Small ice is selected.
Water tank is full
and beeping. (see trou-
bleshooting section)
Medium ice is selected.
Large ice is selected.
Ice bucket is full of ice
Compressor on
Compressor off
Stand-by mode
Ice maker low on
water (see trouble-
shooting section)
Sensor breakdown
(see troubleshoot-
ing section)
1
2
3
Simultaneous
Indicator lights All icons flashing at
the same time System malfunction
(see troubleshooting
section)
4
INDICATOR LIGHTS
4

OPERATING INSTRUCTIONS
CHANGING THE SIZE OF ICE
NOTE: Ice cube sizes differ by density and not volume.A large cube is the same size as a small cube but contains
more frozen water.
1. Ensure the water supply is connected before changing ice size. The ice maker is automatically set to make
medium ice. If you need to change the ice size, you can press the corresponding buttons (see previous page) and
the chosen ice size will be indicated by the corresponding indicator light.
2. If you want to stop making ice but keep the unit on standby, press the power button for about 3 seconds. All ice
indicator lights will turn off and the power indicator light will continue flashing. You are now in standby mode. Do
not leave the unit in standby mode in excess of 6 hours. If you want to start making ice again, press the power
button one more time.
ICE BUCKET
Your ice bucket is designed to be easily removed. To remove it, tilt up the front part of the box then simply pull it out
(see Fig. F)
CONTINUOUS WATER CIRCULATION
This unit operates using a continuous closed cycle of
water, with little or no waste. When the unit is on and the water container is low, new water is allowed in from the water
source. The water container fills up until the float on the water tank is triggered. The recirculation pump cycles water
over the evaporator tray continuously until ice is produced. This process is continuous as long as the unit is left on.
Any water that enters the drain at the bottom of the ice maker cavity is not recycled. It goes into a separate receptacle
with a separate drain system that drains out of the back of the unit. This ensures that you’re always using clean water.
Note: If the unit is turned off for 24 hours or longer, drain the water from the recirculation system. (see below)
Note: If you are using the continuous drain option (see separate installation instructions) the unit may be turned off
during the draining process. If you are using the drain pump option (see separate installation instructions), you must
keep the unit turned on.
To drain the water from the system: First turn off the water supply. Remove the ice bucket, and pull the rubber
drain tube out from its clips at the front of the internal water reservoir. Slowly lower the rubber drain tube towards the
drain port at the back right side of the ice maker cavity. The water will evacuate. When all the water has been drained,
replace the tube. Note: If using the continuous drain option (see separate installation instructions) and the unit
had been turned off, it may now be turned on again.
This machine is intended to produce ice only. It is not intended for the
long-term storage of ice. Move any excess ice into a freezer for long-term
storage (>6 hours) if you desire to keep it.
IMPORTANT
5
Fig. F

POWER FAILURE
Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you
minimize the number of times the door is opened. If the power is going to be off for a longer period of time, and you
are using the drain pump option (see separate installation instructions), you will need to manually drain the water from
your unit before next use to avoid an overflow situation. Refer to ‘Continuous Drain Installation’ for draining instruc-
tions on separate installation manual. Note: Drain the water from the exterior drain bucket by unscrewing the drain
cap located on the back of the unit.
Note: When the power is restored the unit will be in standby mode and the pump will energize itself
automatically to prevent water leakage.
MOVING YOUR ICE MAKER
• Remove all items.
• Securely tape down all loose items (bucket) inside your appliance.
• Turn the adjustable leg up to the base to avoid damage.
• Tape the door shut.
• Be sure the appliance stays secure in the upright position during transportation. Also protect outside of appliance
with a blanket, or similar item.
• The ice maker should be relocated to the coolest area of the room, away from heat producing appliances, and out
of the direct sunlight.
ICE SCOOP
This appliance comes equipped with a stainless steel ice scoop that also facilitates the removal of ice from the ice
bucket. Use this scoop to break up any sheets of ice that fall into the bucket.
OPERATING INSTRUCTIONS
OUTSIDE CABINET AND DOOR
• Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a clean
soft cloth.
• Wring excess water out of the sponge or cloth when cleaning any electrical parts.
CARE AND MAINTENANCE
6
Drain Cap Bottom back
panel
Exterior
drain bucket

CLEANING CYCLE
Note: The frequency of cleaning will be determined by the hardness of your water and the amount of use.
1. Before starting, turn the unit off and turn off the water supply to unit.
2. When all ice has melted from the evaporator and fallen into the ice bucket, remove the bucket (being careful not to
spill any water) and discard or store ice in a separate freezer.
Note: If you are using the continuous drain option, the unit must be turned off during the next step. If you are using
the drain pump option (see separate installation instructions), please keep the unit turned on (this allows pump to
operate.)
3. Remove the rubber drain hose from the left front (Fig. H, item 4) of the ice maker cavity. Slowly tilt the drain hose
down towards the drain port at the back right – lower corner of the ice maker cavity. The water will drain into the
drain port. Tilt the drain hose slowly to ensure that the water is not able to overflow the ice bucket area. (See
Fig.H)
4. When the water stops coming out of the drain hose, ensure that all water has been drained from water tank area.
(Look inside to check that all water has been drained from water container area.) Check the water tank for any ex-
cess sediment and remove any if present. Flush out tank before reinstalling drain hose in clips. Reinstall the drain
hose by pushing it back into the clips.
5. Fill the water tank with a cleaning solution comprised of equal parts water and vinegar. Next, turn the water sup-
ply on.
6. If the bucket has been removed, reinstall the ice bucket after the water tank stops refilling, and the unit begins to
run again.
7. Allow the unit to produce 4 - 6 batches of ice, then turn the unit off and allow any remaining ice to fall into the ice
bucket.
8. Remove the ice bucket and discard all (6) batches of ice.
9. If the drain pump mode is being used (see separate installation instructions), turn the unit on at this point. Unit
has to be in the process (operating mode) in order for the pump to work. If unit is in standby mode pump will not
operate. Once again, remove the rubber drain hose from left side clips and slowly drain the cleaning solution into
the drain port in bottom right side of cabinet area.
10. When all of the solution has drained, reinstall the drain hose into the clips, turn water on and allow tank to fill. Re-
install the ice bucket. Make sure the reservoir is full before unit is turned back on.
11. Discard the first 2 batches of ice that fall into the ice bucket.
12. Normal ice production can continue when there is no evidence of the cleaning solution remaining in the
unit.
CARE AND MAINTENANCE
1
2
1. Evaporator cover board
2. Direction plate
3. Water container
4. Drain hose
5. Clips
Fig.H
Fig.G
43
5
7

CARE AND MAINTENANCE
YEARLY MAINTENANCE FOR AREAS WITH HARD WATER
1. When all ice has been released from the evaporator and fallen into the ice bucket, remove the bucket (being
careful not to spill any water that has resulted from melting ice) and discard or store ice in a separate freezer.
Note: If you are using the continuous drain option (see separate installation instructions), the unit may be turned off
during the next step. If you are using the drain pump option (see separate installation instructions), the unit MUST be
turned on. If unit is in standby mode the pump will continue to energize itself to avoid water leakage.
Note: Water supply should be turned off, if not it will keep filling up.
2. Remove the rubber drain tube (4) from the water container (3). Slowly tilt the drain hose down towards the drain
port at the back right – lower corner of the ice maker cavity. The water will drain into the drain port. (see Fig.H on
previous page)
Note: Tilt the drain tube slowly to ensure that the water does not overflow in the ice bucket area.
3. When the water stops coming out of the drain tube, look inside to check that all water has been drained from
water container area. Reinstall the drain tube by pushing it back into the clips.
4. Use a sterile brush to scrape and loosen any hard water buildup from the water container (3), ice bucket, cover
board (1) and direction plate (2.) Then, fill the water container (3) with an approved, nontoxic, lime dissolving
cleaning solution such as an ice maker cleaner sold in stores, or a solution of equal parts water and vinegar. (see
Fig.G on previous page)
5. Next, turn the water supply on, turn the unit back on only if using continuous drain option (see separate installation
instructions) and had previously turned unit off, and reinstall the ice bucket. The water container will refill, and the
unit will begin to run again.
6. Allow the unit to produce 4 - 6 batches of ice, then turn the unit off and allow time for any remaining ice to fall into
the ice bucket.
7. Remove the ice bucket and discard all (6) batches of ice.
Note: Water supply should be turned off, if not it will keep filling up.
8. Once again, remove the rubber drain tube from water container (3) and slowly drain the cleaning solution into the
drain port in bottom right side of cabinet area. Water will continue to fill if water is not turned off. (See Fig.H on
previous page)
9. When all of the solution has drained, reinstall the ice bucket. Turn the unit back on, only if using continuous drain
option (see separate installation instructions) and had previously turned unit off.
10. Discard the first 2 batches of ice that fall into the ice bucket.
11. Normal ice production can continue when there is no evidence of the cleaning solution remaining in the unit.
VACATION TIME
• If the unit will not be used for more than one day, turn the unit off and drain completely (refer to ‘Continuous
Water Circulation for draining instructions.)
• Winterization: If the unit is only used half the year, the other half it should be kept clean and void of water. Drain
the unit as in the ‘Continuous Water Circulation’ section.Additionally, be sure to remove any water from the drain
tank. Utilize the “cleaning cycle” section.
8

Occasionally, a problem is minor and a service call may not be necessary - use this troubleshooting guide for a possi-
ble solution. If the unit continues to operate improperly, call an authorized service depot or our toll free number.
Tel: [phone]
PROBLEM POSSIBLE CAUSE SOLUTION
The ice maker does not operate • Not plugged in
• The appliance is turned off
• No power to the unit
• Make sure the appliance is
plugged in and turned on
• Replace the fuse or reset circuit
breaker
The ice is not big enough or
melts too quickly • The ambient temperature is too high
• The door is open too often or the
door is ajar
• The condenser is dirty
• Incorrect mode is selected
• Reduce ambient temperature
• Make sure the door is closed
and is only opened when nec-
essary. Ensure that the gasket
is sealing against the cabinet
• Remove the front bottom kick
plate from the unit and using a
vacuum, clean the area of the
condenser
• Select the correct ice size
Ice maker alarm • External water tank is full
• Not enough water • See below
Vibrations • Ice maker not level • Make sure the floor is level
• Adjust levelling legs
Noise • The ice maker is not level
• The rattling noise may come
from the flow of the refrigerant,
which is normal
• As each cycle ends, you may
hear gurgling sounds caused by
the flow of refrigerant in your ice
maker
• Contraction and expansion of
the inside walls may cause pop-
ping and crackling noises
• The ice dispensing during every
cycle may cause some noise
• The constant water flow noise is
a normal function of the unit
• Make sure the floor is level or
adjust the levelling legs
• This is normal
• This is normal
• This is normal
• This is normal
• This is normal
Water leakage from the ice
maker • The water inlet pipe in the back is too loose
• The water outlet pipe in the back
is too loose
• Tighten the water inlet pipe
• Tighten the water outlet pipe
TROUBLESHOOTING
1. “Water tank is full” - troubleshoot using instructions before contacting an authorized service centre.
• Disconnect from power source. Unscrew the drain cap located on the back of the unit and let out the water (refer to installation
guide)
• After draining out all the water from the outside water tank, reconnect unit to power and it will continue to run normally.
• If “drain pump mode” (see separate installation instructions) is being used, please confirm the “drain pump switch” is in the “ON”
position.
2. “Ice maker low on water” - troubleshoot using these instructions before contacting an authorized service centre.
• Check if outside water supply is functioning normally. Follow “checking the water supply” instructions (above) and wait 30 min-
utes for the unit to correct itself.
• If this doesn’t work, press the power button to restart the unit.
3. “Sensor breakdown” - contact our authorized service centre for maintenance.
4. “System malfunction” - System will shut down call an authorized service centre.
9

LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , i t will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: [phone] FAX: [phone]
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: [phone] FAX: [phone]
04/09
1-800-263-2629
Warranty Service
In-home
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest
service center your unit must be delivered to the nearest authorized Danby Service Depot, as service
must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-
tation charges to and from the service location are not protected by this warranty and are the responsi-
bility of the purchaser.
During the first twenty four (24) months, any functional parts of this product found to be defective, will be
repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized
Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it
will be the consumer’s responsibility to transport the appliance (at their own expense) to the original
retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby
service depot, where service must be performed by a qualified service technician. If service is performed
on the units by anyone other than an authorized service depot, or the unit is used for commercial
application, all obligations of Danby under this warranty shall be void.
First 24 months
To obtain
service
Boundaries of
in-home service
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is
used under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or
Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or
implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or
guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation
or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons
or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit
and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for
damages to persons or property caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for
outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event
warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.
Warranty Service
In-home
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: [phone] FAX: [phone]
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: [phone] FAX: [phone]
1-844-455-6097
05/14

NOTES / REMARQUES / NOTAS :
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________
__________________________________________________________________________________________

Model 0RGqOH0RGHOR
For service, contact your nearest service
depot or call:
1-844-455-6097
to recommend a depot in
your area.
Pour obtenir de l’assistance, commu-
niquez avec votre centre de service le
plus rapproché ou composez le :
1-844-455-6097
pour localiser le dépositaire de votre
région
Danby Products Limited, Guelph, Ontario Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio USA 45840
Printed in China
Imprimé en Chine
Impreso en China
The model number can be found on the serial plate located on the
back panel of the unit.
All repair parts available for purchase or special order when you visit
your nearest service depot. To request service and/or the location of
the service depot nearest you, call toll free.
When requesting service or ordering parts, always provide the follow-
ing information:
3URGXFW7\SH
0RGHO1XPEHU
3DUW'HVFULSWLRQ
3DUW1XPEHU
Le numéro de modèle se trouve sur la plaque d’information sur la
paroi arrière de l’appareil.
Toutes les pièces de recharge ou commandes speciales sont
disponibles de votre centre regional de service autorise. Pour exiger le
service et-ou le nom de votre centre de service regional, signalez le
QXPpURVDQVIUDLV
Ayez les renseignements suivants à la portée de la main lors de la
commande de pièce ou service :
*HQUHGHSURGXLW
1XPpURGHPRGqOH
'HVFULSWLRQGHODSLqFH
1XPpURGHSLqFH
Para reparaciones, llame a su centro
de reparaciones más cerano o al:
1-844-455-6097
para recomendarle un centro de repara-
ciones en su área.
El número de modelo se puede encontrar en la placa serial situada en
el panel trasero de la unidad.
Todas las piezas de reparación disponsibles para la comprao la orden
especial cuando usted visita su depósito más cerca posible usted,
OODPDJUDWLV
Al pedir servico o pidiendo piezas, proporcione siempre la información
siguiente:
7LSRGHSURGXFWR
1~PHURGHPRGHOR
'HVFULSFLyQGHODSDUWH
1~PHURGHSLH]D
DIM32D1BSSPR