Silicon Laboratories EFR32xG21 Wireless Gecko User manual

EFR32xG21 Wireless Gecko
Reference Manual
The EFR32xG21 Wireless Gecko SoC is the first device in the Series 2 Wireless Gecko
Portfolio, and includes the EFR32MG21 Mighty Gecko and EFR32BG21 Blue Gecko.
The EFR32xG21 improves processing capability with a Cortex M33 core and has best in
class link budget while providing for lower active current for both the MCU and radio. The
dedicated security core (Secure Element) provides improved cryptography and hardware
security that is isolated from the main application CPU. This high performance and se-
cure multi-protocol device supports Zigbee, Thread, and Bluetooth 5.0.
The single-die solution provides industry-leading energy efficiency, processing capability,
and RF performance in a small form factor for IoT connected applications.
KEY FEATURES
• 32-bit ARM® Cortex M33 core with 80
MHz maximum operating frequency
• Scalable Memory and Radio configuration
options available in QFN packaging
• Peripheral Reflex System enabling
autonomous interaction of MCU
peripherals
• Autonomous Hardware Crypto Accelerator
and True Random Number Generator
• Multiple Integrated 2.4 GHz PAs with up to
20 dBm transmit power
Security
Secure Debug
Authentication
Timers and Triggers
32-bit bus
Peripheral Reflex System
Serial
Interfaces
I/O Ports Analog I/F
Lowest power mode with peripheral operational:
USART
I2C
External
Interrupts
General
Purpose I/O
Pin Reset
Pin Wakeup
iADC
Analog
Comparator
EM4—Shutoff
Energy
Management
Brown-Out
Detector
Voltage
Regulator
Power-On Reset
Clock Management
HF Crystal
Oscillator
LF Crystal
Oscillator
LF
RC Oscillator
HF
RC Oscillator
EM23 HF RC
Oscillator
Crypto Acceleration
Secure Element
Ultra LF RC
Oscillator
Core / Memory
ARM CortexTM M33 processor
with DSP extensions,
FPU and Trust Zone
ETM Debug Interface RAM Memory LDMA
Controller
Flash Program
Memory
Real Time
Capture Counter
Timer/Counter
Low Energy Timer Watchdog Timer
Protocol Timer
EM3—StopEM2—Deep SleepEM1—SleepEM0—Active
True Random
Number Generator
Fast Startup
RC Oscillator
Back-Up Real
Time Counter
Radio Transceiver
DEMOD
AGC
IFADC
CRC
BUFC
MOD
FRC
RAC
Frequency
Synth
PGA
RF Frontend
I
Q
PA
LNA
PA
silabs.com | Building a more connected world. Rev. 0.4

Table of Contents
1. About This Document ...........................22
1.1 Introduction ...............................22
1.2 Conventions ...............................23
1.3 Related Documentation ...........................24
2. System Overview .............................25
2.1 Introduction ...............................26
2.2 Block Diagrams..............................26
2.3 MCU Features overview ...........................27
2.4 Oscillators and Clocks ...........................29
2.5 RF Frequency Synthesizer ..........................29
2.6 Modulation Modes .............................29
2.7 Transmit Mode ..............................30
2.8 Receive Mode ..............................30
2.9 Data Buffering ..............................30
2.10 Unbuffered Data Transfer ..........................30
2.11 Frame Format Support ...........................30
2.12 Hardware CRC Support ..........................31
2.13 Convolutional Encoding / Decoding ......................31
2.14 Binary Block Encoding / Decoding .......................31
2.15 Data Encryption and Authentication ......................32
2.16 Timers ................................33
2.17 RF Test Modes .............................33
3. System Processor ............................34
3.1 Introduction ...............................34
3.2 Features ................................35
3.3 Functional Description ...........................35
3.3.1 Interrupt Operation ...........................36
3.3.2 TrustZone ..............................36
3.3.3 Interrupt Request lines (IRQ) ........................37
4. Memory and Bus System ..........................39
4.1 Introduction ...............................39
4.2 Functional Description ...........................40
4.2.1 Bus Matrix ..............................41
4.2.2 Flash ................................42
4.2.3 SRAM ...............................42
4.2.4 Peripherals ..............................42
5. Radio Transceiver ............................48
silabs.com | Building a more connected world. Rev. 0.4 | 2

5.1 Introduction ...............................49
6. MSC - Memory System Controller ......................50
6.1 Introduction ...............................50
6.2 Features ................................51
6.3 Functional Description ...........................51
6.3.1 Ram Configuration ...........................51
6.3.2 Instruction Cache............................52
6.3.3 Device Information (DI) Page .......................52
6.3.4 User Data (UD) Page Description ......................52
6.3.5 Bootloader ..............................52
6.3.6 Post-reset Behavior ...........................52
6.3.7 Flash Startup .............................52
6.3.8 Wait-states ..............................53
6.3.9 Cortex-M33 If-Then Block Folding ......................53
6.3.10 Line Buffering (Prefetch) .........................53
6.3.11 Erase and Write Operations........................54
6.4 DEVINFO - Device Info Page .........................55
6.4.1 Register Map .............................56
6.4.2 Register Description...........................57
6.5 ICACHE - Instruction Cache .........................84
6.5.1 Cache Operation ............................84
6.5.2 Performance Measurement ........................85
6.5.3 Register Map .............................86
6.5.4 Register Description...........................87
6.6 SYSCFG - System Configuration ........................93
6.6.1 Ram Retention ............................93
6.6.2 ECC ................................94
6.6.3 RAM Wait-states ............................94
6.6.4 RAM Prefetch .............................94
6.6.5 RAM Cache .............................94
6.6.6 Software Interrupts ...........................94
6.6.7 Bus faults ..............................94
6.6.8 Register Map .............................95
6.6.9 Register Description...........................98
6.7 Register Map .............................110
6.8 Register Description ...........................112
6.8.1 MSC_IPVERSION - IP version ID .....................112
6.8.2 MSC_READCTRL - Read Control Register ..................113
6.8.3 MSC_WRITECTRL - Write Control Register..................114
6.8.4 MSC_WRITECMD - Write Command Register .................115
6.8.5 MSC_ADDRB - Page Erase/Write Address Buffer ................116
6.8.6 MSC_WDATA - Write Data Register ....................116
6.8.7 MSC_STATUS - Status Register .....................117
6.8.8 MSC_IF - Interrupt Flag Register .....................118
6.8.9 MSC_IEN - Interrupt Enable Register ....................119
silabs.com | Building a more connected world. Rev. 0.4 | 3

6.8.10 MSC_USERDATASIZE - user data regsion size ................119
6.8.11 MSC_CMD - Command Register .....................120
6.8.12 MSC_LOCK - Configuration Lock Register ..................120
6.8.13 MSC_MISCLOCKWORD - Mass erase and User data page lock word ........121
6.8.14 MSC_PAGELOCK0 - Main space page 0-31 lock word .............121
6.8.15 MSC_PAGELOCK1 - Main space page 32-63 lock word .............122
6.8.16 MSC_PAGELOCK2 - Main space page 64-95 lock word .............122
6.8.17 MSC_PAGELOCK3 - Main space page 96-127 lock word.............123
6.8.18 MSC_TESTCTRL - Flash test control register.................123
7. DBG - Debug Interface ...........................124
7.1 Introduction ..............................124
7.2 Features ...............................124
7.3 Functional Description ..........................125
7.3.1 Debug Pins.............................125
7.3.2 Embedded Trace Macrocell V3.5 (ETM) ...................125
7.3.3 Debug and EM2/EM3 .........................125
7.4 Register Map .............................126
7.5 Register Description ...........................126
7.5.1 DBG_DCIWDATA - Write Data ......................126
7.5.2 DBG_DCIRDATA - Read Data ......................126
7.5.3 DBG_DCISTATUS - Status .......................127
7.5.4 DBG_DCIID - Identification .......................127
7.5.5 DBG_SYSCOM0 - Communication Status ..................128
7.5.6 DBG_SYSCOM1 - Communication Status ..................129
7.5.7 DBG_SYSPWR0 - Power Status .....................130
7.5.8 DBG_SYSCLK0 - Clocking Status .....................132
7.5.9 DBG_SYSID - Identification .......................134
8. CMU - Clock Management Unit ........................135
8.1 Introduction ..............................135
8.2 Features ...............................135
8.3 Functional Description ..........................136
8.3.1 System Clocks ...........................138
8.3.2 Switching Clock Source ........................140
8.3.3 RC Oscillator Calibration ........................142
8.3.4 Energy Modes............................145
8.3.5 Clock Output on a Pin .........................145
8.3.6 Clock Input from a Pin .........................146
8.3.7 Clock Output on PRS .........................146
8.3.8 Interrupts .............................146
8.3.9 Protection .............................146
8.4 Register Map .............................147
8.5 Register Description ...........................149
8.5.1 CMU_IPVERSION - IP version ID .....................149
8.5.2 CMU_STATUS - Status Register .....................150
silabs.com | Building a more connected world. Rev. 0.4 | 4

8.5.3 CMU_LOCK - Configuration Lock Register ..................151
8.5.4 CMU_WDOGLOCK - WDOG Configuration Lock Register .............151
8.5.5 CMU_IF - Interrupt Flag Register .....................152
8.5.6 CMU_IEN - Interrupt Enable Register ....................152
8.5.7 CMU_CALCMD - Calibration Command Register ................153
8.5.8 CMU_CALCTRL - Calibration Control Register .................154
8.5.9 CMU_CALCNT - Calibration Result Counter Register ..............155
8.5.10 CMU_SYSCLKCTRL - System Clock Control .................156
8.5.11 CMU_TRACECLKCTRL - Debug Trace Clock Control ..............157
8.5.12 CMU_EXPORTCLKCTRL - Export Clock Control ...............158
8.5.13 CMU_DPLLREFCLKCTRL - Digital PLL Reference Clock Control ..........160
8.5.14 CMU_EM01GRPACLKCTRL - EM01 Peripheral Group A Clock Control ........161
8.5.15 CMU_EM23GRPACLKCTRL - EM23 Peripheral Group A Clock Control ........161
8.5.16 CMU_EM4GRPACLKCTRL - EM4 Peripheral Group A Clock Control .........162
8.5.17 CMU_IADCCLKCTRL - IADC Clock Control .................162
8.5.18 CMU_WDOG0CLKCTRL - Watchdog0 Clock Control ..............163
8.5.19 CMU_WDOG1CLKCTRL - Watchdog1 Clock Control ..............164
8.5.20 CMU_RTCCCLKCTRL - RTCC Clock Control.................164
8.5.21 CMU_RADIOCLKCTRL - Radio Clock Control ................165
9. Oscillators ...............................166
9.1 Introduction ..............................166
9.2 HFXO - High Frequency Crystal Oscillator ....................166
9.2.1 Introduction ............................166
9.2.2 Features .............................166
9.2.3 Functional Description .........................167
9.2.4 Register Map ............................170
9.2.5 Register Description ..........................171
9.3 HFRCO - High-Frequency RC Oscillator ....................181
9.3.1 Introduction ............................181
9.3.2 Features .............................181
9.3.3 Functional Description .........................181
9.3.4 Register Map ............................184
9.3.5 Register Description ..........................185
9.4 DPLL - Digital Phased Locked Loop ......................189
9.4.1 Introduction ............................189
9.4.2 Features .............................189
9.4.3 Functional Description .........................189
9.4.4 Register Map ............................191
9.4.5 Register Description ..........................192
9.5 LFXO - Low-Frequency Crystal Oscillator ....................197
9.5.1 Introduction ............................197
9.5.2 Features .............................197
9.5.3 Functional Description .........................197
9.5.4 Register Map ............................199
9.5.5 Register Description ..........................200
9.6 LFRCO - Low-Frequency RC Oscillator ....................207
silabs.com | Building a more connected world. Rev. 0.4 | 5

9.6.1 Introduction ............................207
9.6.2 Features .............................207
9.6.3 Functional Description .........................207
9.6.4 Register Map ............................209
9.6.5 Register Description ..........................210
9.7 FSRCO - Fast Start RCO .........................213
9.7.1 Introduction ............................213
9.7.2 Features .............................213
9.7.3 Functional Description .........................213
9.7.4 Register Map ............................213
9.7.5 Register Description ..........................214
9.8 ULFRCO - Ultra Low Frequency RC Oscillator ..................214
9.8.1 Introduction ............................214
9.8.2 Features .............................214
9.8.3 Functional Description .........................214
10. SMU - Security Management Unit ......................215
10.1 Introduction .............................215
10.2 Features ..............................215
10.3 Functional Description ..........................216
10.3.1 Bus Level Security ..........................216
10.3.2 Privileged Access Control .......................217
10.3.3 Secure Access Control ........................217
10.3.4 ARM Trust Zone ..........................218
10.3.5 Configuring Masters .........................218
10.3.6 Configuring Peripherals ........................218
10.3.7 Configuring Memory .........................219
10.3.8 Cortex-M33 Integration ........................219
10.3.9 Exception Handling .........................220
10.3.10 SMU Lock ............................220
10.4 Register Map .............................221
10.5 Register Description ...........................223
10.5.1 SMU_IPVERSION - IP Version .....................223
10.5.2 SMU_STATUS - Status Register .....................224
10.5.3 SMU_LOCK - Lock Register ......................224
10.5.4 SMU_IF - Interrupt Flag Register .....................225
10.5.5 SMU_IEN - Interrupt Enable Register ...................226
10.5.6 SMU_M33CTRL - M33 Control Settings ..................227
10.5.7 SMU_PPUPATD0 - Privileged Access ...................228
10.5.8 SMU_PPUPATD1 - Privileged Access ...................230
10.5.9 SMU_PPUSATD0 - Secure Access ....................232
10.5.10 SMU_PPUSATD1 - Secure Access ....................234
10.5.11 SMU_PPUFS - Fault Status ......................235
10.5.12 SMU_BMPUPATD0 - Privileged Attribute ..................236
10.5.13 SMU_BMPUSATD0 - Secure Attribute...................237
10.5.14 SMU_BMPUFS - Fault Status .....................238
10.5.15 SMU_BMPUFSADDR - Fault Status Address ................238
silabs.com | Building a more connected world. Rev. 0.4 | 6

10.5.16 SMU_ESAURTYPES0 - Region Types 0 ..................239
10.5.17 SMU_ESAURTYPES1 - Region Types 1 ..................239
10.5.18 SMU_ESAUMRB01 - Movable Region Boundary ...............240
10.5.19 SMU_ESAUMRB12 - Movable Region Boundary ...............240
10.5.20 SMU_ESAUMRB45 - Movable Region Boundary ...............241
10.5.21 SMU_ESAUMRB56 - Movable Region Boundary ...............241
11. SE - Secure Element Subsystem ......................242
11.1 Introduction .............................242
11.2 Features ..............................242
11.2.1 Basic Security Features ........................242
11.3 Security Features ...........................242
11.3.1 Secure Debug ...........................243
11.3.2 Cryptographic Acceleration .......................243
11.3.3 True Random Number Generation ....................243
11.4 SE Mailbox .............................243
11.4.1 Sending Commands .........................243
11.4.2 Receiving Responses ........................243
11.4.3 Register Map ...........................244
11.4.4 Register Description .........................244
12. EMU - Energy Management Unit ......................251
12.1 Introduction..............................251
12.2 Features ..............................252
12.3 Functional Description ..........................253
12.3.1 Energy Modes ...........................254
12.3.2 Entering Low Energy Modes ......................258
12.3.3 Exiting a Low Energy Mode ......................259
12.3.4 Brown Out Detector (BOD) .......................260
12.3.5 Reset Management Unit ........................261
12.3.6 Temperature Sensor .........................262
12.3.7 Register Resets ...........................263
12.3.8 Register Locks ...........................263
12.4 Register Map .............................264
12.5 Register Description ...........................266
12.5.1 EMU_DECBOD - DECOUPLE LVBOD Control register .............266
12.5.2 EMU_BOD3SENSE - BOD3SENSE Control register ..............267
12.5.3 EMU_LOCK - EMU Configuration lock register ................267
12.5.4 EMU_IF - Interrupt Flags ........................268
12.5.5 EMU_IEN - Interrupt Enables ......................269
12.5.6 EMU_EM4CTRL - EM4 Control .....................270
12.5.7 EMU_CMD - EMU Command register ...................271
12.5.8 EMU_CTRL - EMU Control register ....................272
12.5.9 EMU_TEMPLIMITS - EMU Temperature thresholds ..............273
12.5.10 EMU_STATUS - EMU Status register ...................274
12.5.11 EMU_TEMP - Temperature ......................275
12.5.12 EMU_RSTCTRL - Reset Management Control register .............276
silabs.com | Building a more connected world. Rev. 0.4 | 7

12.5.13 EMU_RSTCAUSE - Reset cause ....................278
12.5.14 EMU_DGIF - Interrupt Flags Debug ...................279
12.5.15 EMU_DGIEN - Interrupt Enables Debug ..................280
12.5.16 EMU_SEIF - Interrupt Flags Secure Element ................281
12.5.17 EMU_SEIEN - Interrupt Enables Secure Elements ..............281
13. PRS - Peripheral Reflex System .......................282
13.1 Introduction..............................282
13.2 Features ..............................282
13.3 Functional Description ..........................283
13.3.1 Asynchronous Channel Functions.....................283
13.3.2 Configurable Logic ..........................284
13.3.3 Producers .............................285
13.3.4 Consumers ............................290
13.4 Register Map .............................291
13.5 Register Description ...........................304
13.5.1 PRS_IPVERSION - IP version ID .....................304
13.5.2 PRS_ASYNC_SWPULSE - Software Pulse Register ..............305
13.5.3 PRS_ASYNC_SWLEVEL - Software Level Register ..............306
13.5.4 PRS_ASYNC_PEEK - Async Channel Values ................307
13.5.5 PRS_SYNC_PEEK - Sync Channel Values .................308
13.5.6 PRS_ASYNC_CHx_CTRL - Async Channel Control Register ...........309
13.5.7 PRS_SYNC_CHx_CTRL - Sync Channel Control Register ............310
13.5.8 PRS_CONSUMER_CMU_CALDN - CMU CALDN Consumer Selection ........311
13.5.9 PRS_CONSUMER_CMU_CALUP - CMU CALUP Consumer Selection ........311
13.5.10 PRS_CONSUMER_IADC0_SCANTRIGGER - IADC0 SCANTRIGGER Consumer Selection 312
13.5.11 PRS_CONSUMER_IADC0_SINGLETRIGGER - IADC0 SINGLETRIGGER Consumer
Selection .............................312
13.5.12 PRS_CONSUMER_LDMAXBAR_DMAREQ0 - DMAREQ0 Consumer Selection ....313
13.5.13 PRS_CONSUMER_LDMAXBAR_DMAREQ1 - DMAREQ1 Consumer Selection ....313
13.5.14 PRS_CONSUMER_LETIMER0_CLEAR - LETIMER CLEAR Consumer Selection ....314
13.5.15 PRS_CONSUMER_LETIMER0_START - LETIMER START Consumer Selection ....314
13.5.16 PRS_CONSUMER_LETIMER0_STOP - LETIMER STOP Consumer Selection .....315
13.5.17 PRS_CONSUMER_MODEM_DIN - MODEM DIN Consumer Selection........315
13.5.18 PRS_CONSUMER_RAC_CLR - RAC CLR Consumer Selection ..........316
13.5.19 PRS_CONSUMER_RAC_FORCETX - RAC FORCETX Consumer Selection .....316
13.5.20 PRS_CONSUMER_RAC_RXDIS - RAC RXDIS Consumer Selection ........317
13.5.21 PRS_CONSUMER_RAC_RXEN - RAC RXEN Consumer Selection .........317
13.5.22 PRS_CONSUMER_RAC_SEQ - RAC SEQ Consumer Selection ..........318
13.5.23 PRS_CONSUMER_RAC_TXEN - RAC TXEN Consumer Selection .........318
13.5.24 PRS_CONSUMER_RTCC_CC0 - RTCC CC0 Consumer Selection .........319
13.5.25 PRS_CONSUMER_RTCC_CC1 - RTCC CC1 Consumer Selection .........319
13.5.26 PRS_CONSUMER_RTCC_CC2 - RTCC CC2 Consumer Selection .........320
13.5.27 PRS_CONSUMER_SE_TAMPERSRC0 - SE TAMPERSRC0 Consumer Selection ...320
13.5.28 PRS_CONSUMER_SE_TAMPERSRC1 - SE TAMPERSRC1 Consumer Selection ...321
13.5.29 PRS_CONSUMER_SE_TAMPERSRC2 - SE TAMPERSRC2 Consumer Selection ...321
13.5.30 PRS_CONSUMER_SE_TAMPERSRC3 - SE TAMPERSRC3 Consumer Selection ...322
silabs.com | Building a more connected world. Rev. 0.4 | 8

13.5.31 PRS_CONSUMER_SE_TAMPERSRC4 - SE TAMPERSRC4 Consumer Selection ...322
13.5.32 PRS_CONSUMER_SE_TAMPERSRC5 - SE TAMPERSRC5 Consumer Selection ...323
13.5.33 PRS_CONSUMER_SE_TAMPERSRC6 - SE TAMPERSRC6 Consumer Selection ...323
13.5.34 PRS_CONSUMER_SE_TAMPERSRC7 - SE TAMPERSRC7 Consumer Selection ...324
13.5.35 PRS_CONSUMER_CORE_CTIIN0 - CTI0 Consumer Selection ..........324
13.5.36 PRS_CONSUMER_CORE_CTIIN1 - CTI1 Consumer Selection ..........325
13.5.37 PRS_CONSUMER_CORE_CTIIN2 - CTI2 Consumer Selection ..........325
13.5.38 PRS_CONSUMER_CORE_CTIIN3 - CTI3 Consumer Selection ..........326
13.5.39 PRS_CONSUMER_CORE_M33RXEV - M33 Consumer Selection .........326
13.5.40 PRS_CONSUMER_TIMER0_CC0 - TIMER0 CC0 Consumer Selection .......327
13.5.41 PRS_CONSUMER_TIMER0_CC1 - TIMER0 CC1 Consumer Selection .......327
13.5.42 PRS_CONSUMER_TIMER0_CC2 - TIMER0 CC2 Consumer Selection .......328
13.5.43 PRS_CONSUMER_TIMER0_DTI - TIMER0 DTI Consumer Selection ........328
13.5.44 PRS_CONSUMER_TIMER0_DTIFS1 - TIMER0 DTIFS1 Consumer Selection .....329
13.5.45 PRS_CONSUMER_TIMER0_DTIFS2 - TIMER0 DTIFS2 Consumer Selection .....329
13.5.46 PRS_CONSUMER_TIMER1_CC0 - TIMER1 CC0 Consumer Selection .......330
13.5.47 PRS_CONSUMER_TIMER1_CC1 - TIMER1 CC1 Consumer Selection .......330
13.5.48 PRS_CONSUMER_TIMER1_CC2 - TIMER1 CC2 Consumer Selection .......331
13.5.49 PRS_CONSUMER_TIMER1_DTI - TIMER1 DTI Consumer Selection ........331
13.5.50 PRS_CONSUMER_TIMER1_DTIFS1 - TIMER1 DTIFS1 Consumer Selection .....332
13.5.51 PRS_CONSUMER_TIMER1_DTIFS2 - TIMER1 DTIFS2 Consumer Selection .....332
13.5.52 PRS_CONSUMER_TIMER2_CC0 - TIMER2 CC0 Consumer Selection .......333
13.5.53 PRS_CONSUMER_TIMER2_CC1 - TIMER2 CC1 Consumer Selection .......333
13.5.54 PRS_CONSUMER_TIMER2_CC2 - TIMER2 CC2 Consumer Selection .......334
13.5.55 PRS_CONSUMER_TIMER2_DTI - TIMER2 DTI Consumer Selection ........334
13.5.56 PRS_CONSUMER_TIMER2_DTIFS1 - TIMER2 DTIFS1 Consumer Selection .....335
13.5.57 PRS_CONSUMER_TIMER2_DTIFS2 - TIMER2 DTIFS2 Consumer Selection .....335
13.5.58 PRS_CONSUMER_TIMER3_CC0 - TIMER3 CC0 Consumer Selection .......336
13.5.59 PRS_CONSUMER_TIMER3_CC1 - TIMER3 CC1 Consumer Selection .......336
13.5.60 PRS_CONSUMER_TIMER3_CC2 - TIMER3 CC2 Consumer Selection .......337
13.5.61 PRS_CONSUMER_TIMER3_DTI - TIMER3 DTI Consumer Selection ........337
13.5.62 PRS_CONSUMER_TIMER3_DTIFS1 - TIMER3 DTIFS1 Consumer Selection .....338
13.5.63 PRS_CONSUMER_TIMER3_DTIFS2 - TIMER3 DTIFS2 Consumer Selection .....338
13.5.64 PRS_CONSUMER_USART0_CLK - USART0 CLK Consumer Selection .......339
13.5.65 PRS_CONSUMER_USART0_IR - USART0 IR Consumer Selection ........339
13.5.66 PRS_CONSUMER_USART0_RX - USART0 RX Consumer Selection ........340
13.5.67 PRS_CONSUMER_USART0_TRIGGER - USART0 TRIGGER Consumer Selection ...340
13.5.68 PRS_CONSUMER_USART1_CLK - USART1 CLK Consumer Selection .......341
13.5.69 PRS_CONSUMER_USART1_IR - USART1 IR Consumer Selection ........341
13.5.70 PRS_CONSUMER_USART1_RX - USART1 RX Consumer Selection ........342
13.5.71 PRS_CONSUMER_USART1_TRIGGER - USART1 TRIGGER Consumer Selection ...342
13.5.72 PRS_CONSUMER_USART2_CLK - USART2 CLK Consumer Selection .......343
13.5.73 PRS_CONSUMER_USART2_IR - USART2 IR Consumer Selection ........343
13.5.74 PRS_CONSUMER_USART2_RX - USART2 RX Consumer Selection ........344
13.5.75 PRS_CONSUMER_USART2_TRIGGER - USART2 TRIGGER Consumer Selection ...344
13.5.76 PRS_CONSUMER_WDOG0_SRC0 - WDOG0 SRC0 Consumer Selection ......345
13.5.77 PRS_CONSUMER_WDOG0_SRC1 - WDOG0 SRC1 Consumer Selection ......345
13.5.78 PRS_CONSUMER_WDOG1_SRC0 - WDOG1 SRC0 Consumer Selection ......346
silabs.com | Building a more connected world. Rev. 0.4 | 9

13.5.79 PRS_CONSUMER_WDOG1_SRC1 - WDOG1 SRC1 Consumer Selection ......346
14. GPCRC - General Purpose Cyclic Redundancy Check ..............347
14.1 Introduction..............................347
14.2 Features ..............................347
14.3 Functional Description ..........................348
14.3.1 Polynomial Specification ........................349
14.3.2 Input and Output Specification ......................349
14.3.3 Initialization ............................349
14.3.4 DMA Usage ............................349
14.3.5 Byte-Level Bit Reversal and Byte Reordering .................350
14.4 Register Map .............................353
14.5 Register Description ...........................354
14.5.1 GPCRC_IPVERSION - IP Version ID ...................354
14.5.2 GPCRC_EN - CRC Enable .......................355
14.5.3 GPCRC_CTRL - Control Register .....................356
14.5.4 GPCRC_CMD - Command Register ....................357
14.5.5 GPCRC_INIT - CRC Init Value ......................357
14.5.6 GPCRC_POLY - CRC Polynomial Value ..................358
14.5.7 GPCRC_INPUTDATA - Input 32-bit Data Register ...............358
14.5.8 GPCRC_INPUTDATAHWORD - Input 16-bit Data Register ............359
14.5.9 GPCRC_INPUTDATABYTE - Input 8-bit Data Register .............359
14.5.10 GPCRC_DATA - CRC Data Register ...................360
14.5.11 GPCRC_DATAREV - CRC Data Reverse Register ..............360
14.5.12 GPCRC_DATABYTEREV - CRC Data Byte Reverse Register ...........361
15. RTCC - Real Time Clock with Capture.....................362
15.1 Introduction..............................362
15.2 Features ..............................363
15.3 Functional Description ..........................363
15.3.1 RTCC Counter ...........................364
15.3.2 Capture/Compare Channels ......................366
15.3.3 Interrupts and PRS Output .......................367
15.3.4 Register Lock ...........................368
15.3.5 Programmer's Model .........................368
15.3.6 Debug Features and Description .....................368
15.3.7 Compatibility ............................368
15.4 Register Map .............................369
15.5 Register Description ...........................371
15.5.1 RTCC_IPVERSION - IP VERSION ....................371
15.5.2 RTCC_EN - Module Enable Register ...................371
15.5.3 RTCC_CFG - Configuration Register ...................372
15.5.4 RTCC_CMD - Command Register ....................373
15.5.5 RTCC_STATUS - Status register .....................374
15.5.6 RTCC_IF - RTCC Interrupt Flags .....................375
15.5.7 RTCC_IEN - Interrupt Enable Register ...................376
silabs.com | Building a more connected world. Rev. 0.4 | 10

15.5.8 RTCC_PRECNT - Pre-Counter Value Register ................376
15.5.9 RTCC_CNT - Counter Value Register ...................377
15.5.10 RTCC_COMBCNT - Combined Pre-Counter and Counter Valu... ..........377
15.5.11 RTCC_SYNCBUSY - Synchronization Busy Register ..............378
15.5.12 RTCC_LOCK - Configuration Lock Register .................378
15.5.13 RTCC_CCx_CTRL - CC Channel Control Register ..............379
15.5.14 RTCC_CCx_OCVALUE - Output Compare Value Register ............380
15.5.15 RTCC_CCx_ICVALUE - Input Capture Value Register .............380
16. BURTC - Back-Up Real Time Counter .....................381
16.1 Introduction..............................381
16.2 Features ..............................381
16.3 Functional Description ..........................382
16.3.1 Clock Selection ...........................382
16.3.2 Configuration ...........................382
16.3.3 Debug Features and Description .....................382
16.3.4 Counter .............................383
16.3.5 Compare Channel ..........................383
16.3.6 Interrupts .............................384
16.3.7 Register Lock ...........................384
16.4 Register Map .............................385
16.5 Register Description ...........................386
16.5.1 BURTC_IPVERSION - IP version ID ....................386
16.5.2 BURTC_EN - Module Enable Register ...................387
16.5.3 BURTC_CFG - Configuration Register ...................388
16.5.4 BURTC_CMD - Command Register ....................389
16.5.5 BURTC_STATUS - Status Register ....................390
16.5.6 BURTC_IF - Interrupt Flag Register ....................390
16.5.7 BURTC_IEN - Interrupt Enable Register ..................391
16.5.8 BURTC_PRECNT - Pre-Counter Value Register ................391
16.5.9 BURTC_CNT - Counter Value Register ...................392
16.5.10 BURTC_EM4WUEN - EM4 wakeup request Enable Register ...........392
16.5.11 BURTC_SYNCBUSY - Synchronization Busy Register .............393
16.5.12 BURTC_LOCK - Configuration Lock Register ................394
16.5.13 BURTC_COMP - Compare Value Register .................394
17. BURAM - Backup RAM ..........................395
17.1 Introduction..............................395
17.2 Functional Description ..........................395
17.3 Register Map .............................395
17.4 Register Description ...........................396
17.4.1 BURAM_RETx_REG - Retention Register ..................396
18. LETIMER - Low Energy Timer ........................397
18.1 Introduction..............................397
18.2 Features ..............................397
silabs.com | Building a more connected world. Rev. 0.4 | 11

18.3 Functional Description ..........................398
18.3.1 Internal Overview ..........................399
18.3.2 Free Running Mode .........................400
18.3.3 One-shot Mode ...........................401
18.3.4 Buffered Mode ...........................402
18.3.5 Double Mode ...........................403
18.4 Clock Frequency ............................404
18.5 PRS Input Triggers ...........................405
18.6 Debug ...............................405
18.7 Output Action .............................406
18.8 PRS Output .............................406
18.9 Interrupts ..............................406
18.10 Using the LETIMER in EM3 ........................406
18.11 Register access ............................406
18.12 Programmer's Model ..........................407
18.12.1 FREE Running Mode ........................408
18.12.2 One Shot Mode ..........................409
18.12.3 DOUBLE Mode ..........................409
18.12.4 BUFFERED Mode .........................410
18.12.5 Continuous Output Generation .....................411
18.12.6 PWM Output ...........................412
18.13 Register Map.............................413
18.14 Register Description ..........................415
18.14.1 LETIMER_IPVERSION - IP version....................415
18.14.2 LETIMER_EN - module en ......................415
18.14.3 LETIMER_CTRL - Control Register ....................416
18.14.4 LETIMER_CMD - Command Register ...................418
18.14.5 LETIMER_STATUS - Status Register ...................419
18.14.6 LETIMER_CNT - Counter Value Register..................419
18.14.7 LETIMER_COMP0 - Compare Value Register 0 ...............420
18.14.8 LETIMER_COMP1 - Compare Value Register 1 ...............420
18.14.9 LETIMER_TOP - Counter TOP Value Register ................421
18.14.10 LETIMER_TOPBUFF - Buffered Counter TOP Value .............421
18.14.11 LETIMER_REP0 - Repeat Counter Register 0................422
18.14.12 LETIMER_REP1 - Repeat Counter Register 1................422
18.14.13 LETIMER_IF - Interrupt Flag Register ..................423
18.14.14 LETIMER_IEN - Interrupt Enable Register .................424
18.14.15 LETIMER_SYNCBUSY - Synchronization Busy Register ............425
18.14.16 LETIMER_PRSMODE - PRS Input mode select Register ............426
19. TIMER - Timer/Counter ..........................428
19.1 Introduction..............................428
19.2 Features ..............................429
19.3 Functional Description ..........................430
19.3.1 Register Access...........................430
silabs.com | Building a more connected world. Rev. 0.4 | 12

19.3.2 Counter Modes ...........................431
19.3.3 Compare/Capture Channels ......................437
19.3.4 Dead-Time Insertion Unit .......................448
19.3.5 Debug Mode ............................452
19.3.6 Interrupts, DMA and PRS Output .....................452
19.3.7 GPIO Input/Output ..........................452
19.4 Register Map .............................453
19.5 Register Description ...........................456
19.5.1 TIMER_IPVERSION - IP version ID ....................456
19.5.2 TIMER_CFG - Configuration Register ...................457
19.5.3 TIMER_CTRL - Control Register .....................460
19.5.4 TIMER_CMD - Command Register ....................461
19.5.5 TIMER_STATUS - Status Register ....................462
19.5.6 TIMER_IF - Interrupt Flag Register ....................465
19.5.7 TIMER_IEN - Interrupt Enable Register ...................467
19.5.8 TIMER_TOP - Counter Top Value Register .................468
19.5.9 TIMER_TOPB - Counter Top Value Buffer Register ...............468
19.5.10 TIMER_CNT - Counter Value Register ..................469
19.5.11 TIMER_LOCK - TIMER Configuration Lock Register ..............469
19.5.12 TIMER_EN - module en .......................470
19.5.13 TIMER_CCx_CFG - CC Channel Configuration Register ............471
19.5.14 TIMER_CCx_CTRL - CC Channel Control Register ..............473
19.5.15 TIMER_CCx_OC - OC Channel Value Register ...............474
19.5.16 TIMER_CCx_OCB - OC Channel Value Buffer Register .............475
19.5.17 TIMER_CCx_ICF - IC Channel Value Register ................475
19.5.18 TIMER_CCx_ICOF - IC Channel Value Overflow Register ............475
19.5.19 TIMER_DTCFG - DTI Configuration Register ................476
19.5.20 TIMER_DTTIMECFG - DTI Time Configuration Register ............477
19.5.21 TIMER_DTFCFG - DTI Fault Configuration Register ..............478
19.5.22 TIMER_DTCTRL - DTI Control Register ..................479
19.5.23 TIMER_DTOGEN - DTI Output Generation Enable Register ...........480
19.5.24 TIMER_DTFAULT - DTI Fault Register ..................481
19.5.25 TIMER_DTFAULTC - DTI Fault Clear Register ................482
19.5.26 TIMER_DTLOCK - DTI Configuration Lock Register ..............483
20. USART - Universal Synchronous Asynchronous Receiver/Transmitter ........484
20.1 Introduction..............................484
20.2 Features ..............................485
20.3 Functional Description ..........................486
20.3.1 Modes of Operation .........................487
20.3.2 Asynchronous Operation ........................487
20.3.3 Synchronous Operation ........................503
20.3.4 Hardware Flow Control ........................509
20.3.5 Debug Halt ............................509
20.3.6 PRS-triggered Transmissions ......................509
20.3.7 PRS RX Input ...........................509
20.3.8 PRS CLK Input ...........................510
silabs.com | Building a more connected world. Rev. 0.4 | 13

20.3.9 DMA Support ...........................510
20.3.10 Timer ..............................511
20.3.11 Interrupts ............................516
20.3.12 IrDA Modulator/ Demodulator ......................517
20.4 Register Map .............................518
20.5 Register Description ...........................521
20.5.1 USART_IPVERSION - IPVERSION ....................521
20.5.2 USART_EN - USART Enable ......................521
20.5.3 USART_CTRL - Control Register .....................522
20.5.4 USART_FRAME - USART Frame Format Register ...............527
20.5.5 USART_TRIGCTRL - USART Trigger Control register ..............529
20.5.6 USART_CMD - Command Register ....................530
20.5.7 USART_STATUS - USART Status Register .................531
20.5.8 USART_CLKDIV - Clock Control Register ..................532
20.5.9 USART_RXDATAX - RX Buffer Data Extended Register .............533
20.5.10 USART_RXDATA - RX Buffer Data Register ................533
20.5.11 USART_RXDOUBLEX - RX Buffer Double Data Extended Register .........534
20.5.12 USART_RXDOUBLE - RX FIFO Double Data Register .............535
20.5.13 USART_RXDATAXP - RX Buffer Data Extended Peek Register ..........535
20.5.14 USART_RXDOUBLEXP - RX Buffer Double Data Extended Peek R... ........536
20.5.15 USART_TXDATAX - TX Buffer Data Extended Register .............537
20.5.16 USART_TXDATA - TX Buffer Data Register .................538
20.5.17 USART_TXDOUBLEX - TX Buffer Double Data Extended Register .........539
20.5.18 USART_TXDOUBLE - TX Buffer Double Data Register .............540
20.5.19 USART_IF - Interrupt Flag Register....................541
20.5.20 USART_IEN - Interrupt Enable Register ..................543
20.5.21 USART_IRCTRL - IrDA Control Register ..................545
20.5.22 USART_I2SCTRL - I2S Control Register ..................546
20.5.23 USART_TIMING - Timing Register ....................548
20.5.24 USART_CTRLX - Control Register Extended ................550
20.5.25 USART_TIMECMP0 - Used to generate interrupts and vario... ..........552
20.5.26 USART_TIMECMP1 - Used to generate interrupts and vario... ..........554
20.5.27 USART_TIMECMP2 - Used to generate interrupts and vario... ..........556
21. I2C - Inter-Integrated Circuit Interface .....................558
21.1 Introduction..............................558
21.2 Features ..............................558
21.3 Functional Description ..........................559
21.3.1 I2C-Bus Overview ..........................560
21.3.2 Enable and Reset ..........................564
21.3.3 Pin Configuration ..........................564
21.3.4 Safely Disabling and Changing Slave Configuration...............564
21.3.5 Clock Generation ..........................565
21.3.6 Arbitration .............................565
21.3.7 Buffers ..............................565
21.3.8 Master Operation ..........................568
21.3.9 Bus States ............................576
silabs.com | Building a more connected world. Rev. 0.4 | 14

21.3.10 Slave Operation ..........................576
21.3.11 Transfer Automation .........................580
21.3.12 Using 10-bit Addresses ........................581
21.3.13 Error Handling ...........................581
21.3.14 DMA Support ...........................583
21.3.15 Interrupts ............................583
21.3.16 Wake-up .............................583
21.4 Register Map .............................584
21.5 Register Description ...........................586
21.5.1 I2C_IPVERSION - IP VERSION Register ..................586
21.5.2 I2C_EN - Enable Register .......................586
21.5.3 I2C_CTRL - Control Register ......................587
21.5.4 I2C_CMD - Command Register .....................591
21.5.5 I2C_STATE - State Register ......................592
21.5.6 I2C_STATUS - Status Register .....................593
21.5.7 I2C_CLKDIV - Clock Division Register ...................594
21.5.8 I2C_SADDR - Slave Address Register ...................594
21.5.9 I2C_SADDRMASK - Slave Address Mask Register ...............595
21.5.10 I2C_RXDATA - Receive Buffer Data Register ................595
21.5.11 I2C_RXDOUBLE - Receive Buffer Double Data Register ............596
21.5.12 I2C_RXDATAP - Receive Buffer Data Peek Register ..............596
21.5.13 I2C_RXDOUBLEP - Receive Buffer Double Data Peek Register ..........597
21.5.14 I2C_TXDATA - Transmit Buffer Data Register ................597
21.5.15 I2C_TXDOUBLE - Transmit Buffer Double Data Register ............598
21.5.16 I2C_IF - Interrupt Flag Register .....................599
21.5.17 I2C_IEN - Interrupt Enable Register ...................601
22. ACMP - Analog Comparator ........................603
22.1 Introduction .............................603
22.2 Features ..............................603
22.3 Functional Description ..........................604
22.3.1 Configuration and Control .......................604
22.3.2 Warmup Time ...........................605
22.3.3 Response Time ...........................605
22.3.4 Hysteresis ............................605
22.3.5 VREFDIV Sources ..........................606
22.3.6 Supply Voltage Monitoring (VSENSE) ...................606
22.3.7 Input Range and Accuracy Settings ....................606
22.3.8 Capacitive Sense Mode ........................607
22.3.9 Interrupts and PRS Output .......................608
22.3.10 Output to GPIO ..........................608
22.4 Register Map .............................609
22.5 Register Description ...........................610
22.5.1 ACMP_IPVERSION - IP version ID ....................610
22.5.2 ACMP_EN - ACMP enable .......................610
22.5.3 ACMP_CFG - Configuration register ....................611
22.5.4 ACMP_CTRL - Control Register .....................612
silabs.com | Building a more connected world. Rev. 0.4 | 15

22.5.5 ACMP_INPUTCTRL - Input Control Register .................613
22.5.6 ACMP_STATUS - Status Register ....................618
22.5.7 ACMP_IF - Interrupt Flag Register ....................619
22.5.8 ACMP_IEN - Interrupt Enable Register ...................620
22.5.9 ACMP_SYNCBUSY - Syncbusy .....................620
23. IADC - Incremental Analog to Digital Converter .................621
23.1 Introduction..............................621
23.2 Features ..............................622
23.3 Functional Description ..........................623
23.3.1 Register Access...........................624
23.3.2 Clocking .............................625
23.3.3 Conversion Timing ..........................626
23.3.4 Reference Selection and Analog Gain ...................633
23.3.5 Input and Configuration Selection .....................633
23.3.6 Gain and Offset Correction .......................638
23.3.7 Output Data FIFOs ..........................642
23.3.8 Window Compare ..........................644
23.3.9 Interrupts .............................645
23.4 Register Map .............................646
23.5 Register Description ...........................649
23.5.1 IADC_IPVERSION - IPVERSION .....................649
23.5.2 IADC_EN - Enable ..........................649
23.5.3 IADC_CTRL - Control ........................650
23.5.4 IADC_CMD - Command ........................652
23.5.5 IADC_TIMER - Timer .........................653
23.5.6 IADC_STATUS - Status ........................654
23.5.7 IADC_MASKREQ - Mask Request ....................655
23.5.8 IADC_STMASK - Scan Table Mask ....................656
23.5.9 IADC_CMPTHR - Digital Window comparator Threshold .............656
23.5.10 IADC_IF - Interrupt Flags .......................657
23.5.11 IADC_IEN - Interrupt Enable ......................659
23.5.12 IADC_TRIGGER - Trigger .......................661
23.5.13 IADC_CFGx - Configuration ......................664
23.5.14 IADC_SCALEx - Scaling .......................666
23.5.15 IADC_SCHEDx - Scheduling ......................666
23.5.16 IADC_SINGLEFIFOCFG - Single FIFO Configuration .............667
23.5.17 IADC_SINGLEFIFODATA - Single FIFO Read Data ..............668
23.5.18 IADC_SINGLEFIFOSTAT - Single FIFO Status ................668
23.5.19 IADC_SINGLEDATA - Single Data ....................669
23.5.20 IADC_SCANFIFOCFG - Scan FIFO Configuration ...............670
23.5.21 IADC_SCANFIFODATA - Scan FIFO Read Data ...............671
23.5.22 IADC_SCANFIFOSTAT - Scan FIFO Status .................671
23.5.23 IADC_SCANDATA - Scan Data .....................672
23.5.24 IADC_SINGLE - Single Queue Port Selection ................673
23.5.25 IADC_SCANx - SCAN Entry ......................675
24. GPIO - General Purpose Input/Output .....................677
silabs.com | Building a more connected world. Rev. 0.4 | 16

24.1 Introduction .............................677
24.2 Features ..............................678
24.3 Functional Description ..........................679
24.3.1 Pin Configuration ..........................680
24.3.2 Alternate Port Control ........................682
24.3.3 Slew Rate .............................682
24.3.4 Input Disable ............................682
24.3.5 Configuration Lock ..........................682
24.3.6 EM2 Functionality ..........................682
24.3.7 EM4 Functionality ..........................682
24.3.8 EM4 Wakeup ...........................683
24.3.9 Debug Connections .........................683
24.3.10 Interrupt Generation .........................684
24.3.11 Output to PRS ...........................685
24.3.12 Peripheral Resource Routing ......................685
24.4 Synchronization ............................687
24.5 Register Map .............................688
24.6 Register Description ...........................705
24.6.1 GPIO_PORTA_CTRL - Port control ....................705
24.6.2 GPIO_PORTA_MODEL - mode low ....................706
24.6.3 GPIO_PORTA_DOUT - data out .....................710
24.6.4 GPIO_PORTA_DIN - data in ......................710
24.6.5 GPIO_PORTB_CTRL - Port control ....................711
24.6.6 GPIO_PORTB_MODEL - mode low ....................712
24.6.7 GPIO_PORTB_DOUT - data out .....................713
24.6.8 GPIO_PORTB_DIN - data in ......................714
24.6.9 GPIO_PORTC_CTRL - Port control ....................715
24.6.10 GPIO_PORTC_MODEL - mode low ...................716
24.6.11 GPIO_PORTC_DOUT - data out ....................719
24.6.12 GPIO_PORTC_DIN - data in ......................720
24.6.13 GPIO_PORTD_CTRL - Port control ...................721
24.6.14 GPIO_PORTD_MODEL - mode low ...................722
24.6.15 GPIO_PORTD_DOUT - data out ....................725
24.6.16 GPIO_PORTD_DIN - data in ......................725
24.6.17 GPIO_LOCK - main .........................726
24.6.18 GPIO_GPIOLOCKSTATUS - Lock Status .................726
24.6.19 GPIO_ABUSALLOC - A Bus allocation ..................727
24.6.20 GPIO_BBUSALLOC - B Bus allocation ..................729
24.6.21 GPIO_CDBUSALLOC - CD Bus allocation .................731
24.6.22 GPIO_EXTIPSELL - External Interrupt Port Select Low .............733
24.6.23 GPIO_EXTIPINSELL - External Interrupt Pin Select Low ............736
24.6.24 GPIO_EXTIRISE - External Interrupt Rising Edge Trigger ............738
24.6.25 GPIO_EXTIFALL - External Interrupt Falling Edge Trigger ............739
24.6.26 GPIO_IF - Interrupt Flag .......................739
24.6.27 GPIO_IEN - Interrupt Enable ......................740
24.6.28 GPIO_EM4WUEN - main .......................740
24.6.29 GPIO_EM4WUPOL - New Register....................741
silabs.com | Building a more connected world. Rev. 0.4 | 17

24.6.30 GPIO_DBGROUTEPEN - Debugger Route Pin enable .............742
24.6.31 GPIO_TRACEROUTEPEN - Trace Route Pin Enable .............743
24.6.32 GPIO_ACMP0_ROUTEEN - ACMP0 pin enable ...............743
24.6.33 GPIO_ACMP0_ACMPOUTROUTE - ACMPOUT port/pin select ..........744
24.6.34 GPIO_ACMP1_ROUTEEN - ACMP1 pin enable ...............744
24.6.35 GPIO_ACMP1_ACMPOUTROUTE - ACMPOUT port/pin select ..........745
24.6.36 GPIO_CMU_ROUTEEN - CMU pin enable .................745
24.6.37 GPIO_CMU_CLKIN0ROUTE - CLKIN0 port/pin select .............746
24.6.38 GPIO_CMU_CLKOUT0ROUTE - CLKOUT0 port/pin select ...........746
24.6.39 GPIO_CMU_CLKOUT1ROUTE - CLKOUT1 port/pin select ...........747
24.6.40 GPIO_CMU_CLKOUT2ROUTE - CLKOUT2 port/pin select ...........747
24.6.41 GPIO_FRC_ROUTEEN - FRC pin enable .................748
24.6.42 GPIO_FRC_DCLKROUTE - DCLK port/pin select ...............748
24.6.43 GPIO_FRC_DFRAMEROUTE - DFRAME port/pin select ............749
24.6.44 GPIO_FRC_DOUTROUTE - DOUT port/pin select ..............749
24.6.45 GPIO_I2C0_ROUTEEN - I2C0 pin enable .................750
24.6.46 GPIO_I2C0_SCLROUTE - SCL port/pin select ................750
24.6.47 GPIO_I2C0_SDAROUTE - SDA port/pin select ................751
24.6.48 GPIO_I2C1_ROUTEEN - I2C1 pin enable .................751
24.6.49 GPIO_I2C1_SCLROUTE - SCL port/pin select ................752
24.6.50 GPIO_I2C1_SDAROUTE - SDA port/pin select ................752
24.6.51 GPIO_LETIMER0_ROUTEEN - LETIMER pin enable .............753
24.6.52 GPIO_LETIMER0_OUT0ROUTE - OUT0 port/pin select ............753
24.6.53 GPIO_LETIMER0_OUT1ROUTE - OUT1 port/pin select ............754
24.6.54 GPIO_MODEM_ROUTEEN - MODEM pin enable ...............754
24.6.55 GPIO_MODEM_ANT0ROUTE - ANT0 port/pin select .............755
24.6.56 GPIO_MODEM_ANT1ROUTE - ANT1 port/pin select .............755
24.6.57 GPIO_MODEM_DCLKROUTE - DCLK port/pin select .............756
24.6.58 GPIO_MODEM_DINROUTE - DIN port/pin select ...............756
24.6.59 GPIO_MODEM_DOUTROUTE - DOUT port/pin select .............757
24.6.60 GPIO_PRS0_ROUTEEN - PRS0 pin enable.................758
24.6.61 GPIO_PRS0_ASYNCH0ROUTE - ASYNCH0 port/pin select ...........759
24.6.62 GPIO_PRS0_ASYNCH1ROUTE - ASYNCH1 port/pin select ...........760
24.6.63 GPIO_PRS0_ASYNCH2ROUTE - ASYNCH2 port/pin select ...........760
24.6.64 GPIO_PRS0_ASYNCH3ROUTE - ASYNCH3 port/pin select ...........761
24.6.65 GPIO_PRS0_ASYNCH4ROUTE - ASYNCH4 port/pin select ...........761
24.6.66 GPIO_PRS0_ASYNCH5ROUTE - ASYNCH5 port/pin select ...........762
24.6.67 GPIO_PRS0_ASYNCH6ROUTE - ASYNCH6 port/pin select ...........762
24.6.68 GPIO_PRS0_ASYNCH7ROUTE - ASYNCH7 port/pin select ...........763
24.6.69 GPIO_PRS0_ASYNCH8ROUTE - ASYNCH8 port/pin select ...........763
24.6.70 GPIO_PRS0_ASYNCH9ROUTE - ASYNCH9 port/pin select ...........764
24.6.71 GPIO_PRS0_ASYNCH10ROUTE - ASYNCH10 port/pin select ..........764
24.6.72 GPIO_PRS0_ASYNCH11ROUTE - ASYNCH11 port/pin select ..........765
24.6.73 GPIO_PRS0_SYNCH0ROUTE - SYNCH0 port/pin select ............765
24.6.74 GPIO_PRS0_SYNCH1ROUTE - SYNCH1 port/pin select ............766
24.6.75 GPIO_PRS0_SYNCH2ROUTE - SYNCH2 port/pin select ............766
24.6.76 GPIO_PRS0_SYNCH3ROUTE - SYNCH3 port/pin select ............767
24.6.77 GPIO_TIMER0_ROUTEEN - TIMER0 pin enable ...............768
silabs.com | Building a more connected world. Rev. 0.4 | 18

24.6.78 GPIO_TIMER0_CC0ROUTE - CC0 port/pin select ..............769
24.6.79 GPIO_TIMER0_CC1ROUTE - CC1 port/pin select ..............769
24.6.80 GPIO_TIMER0_CC2ROUTE - CC2 port/pin select ..............770
24.6.81 GPIO_TIMER0_CDTI0ROUTE - CDTI0 port/pin select .............770
24.6.82 GPIO_TIMER0_CDTI1ROUTE - CDTI1 port/pin select .............771
24.6.83 GPIO_TIMER0_CDTI2ROUTE - CDTI2 port/pin select .............771
24.6.84 GPIO_TIMER1_ROUTEEN - TIMER1 pin enable ...............772
24.6.85 GPIO_TIMER1_CC0ROUTE - CC0 port/pin select ..............773
24.6.86 GPIO_TIMER1_CC1ROUTE - CC1 port/pin select ..............773
24.6.87 GPIO_TIMER1_CC2ROUTE - CC2 port/pin select ..............774
24.6.88 GPIO_TIMER1_CDTI0ROUTE - CDTI0 port/pin select .............774
24.6.89 GPIO_TIMER1_CDTI1ROUTE - CDTI1 port/pin select .............775
24.6.90 GPIO_TIMER1_CDTI2ROUTE - CDTI2 port/pin select .............775
24.6.91 GPIO_TIMER2_ROUTEEN - TIMER2 pin enable ...............776
24.6.92 GPIO_TIMER2_CC0ROUTE - CC0 port/pin select ..............777
24.6.93 GPIO_TIMER2_CC1ROUTE - CC1 port/pin select ..............777
24.6.94 GPIO_TIMER2_CC2ROUTE - CC2 port/pin select ..............778
24.6.95 GPIO_TIMER2_CDTI0ROUTE - CDTI0 port/pin select .............778
24.6.96 GPIO_TIMER2_CDTI1ROUTE - CDTI1 port/pin select .............779
24.6.97 GPIO_TIMER2_CDTI2ROUTE - CDTI2 port/pin select .............779
24.6.98 GPIO_TIMER3_ROUTEEN - TIMER3 pin enable ...............780
24.6.99 GPIO_TIMER3_CC0ROUTE - CC0 port/pin select ..............781
24.6.100 GPIO_TIMER3_CC1ROUTE - CC1 port/pin select ..............781
24.6.101 GPIO_TIMER3_CC2ROUTE - CC2 port/pin select ..............782
24.6.102 GPIO_TIMER3_CDTI0ROUTE - CDTI0 port/pin select .............782
24.6.103 GPIO_TIMER3_CDTI1ROUTE - CDTI1 port/pin select .............783
24.6.104 GPIO_TIMER3_CDTI2ROUTE - CDTI2 port/pin select .............783
24.6.105 GPIO_USART0_ROUTEEN - USART0 pin enable ..............784
24.6.106 GPIO_USART0_CSROUTE - CS port/pin select ...............784
24.6.107 GPIO_USART0_CTSROUTE - CTS port/pin select ..............785
24.6.108 GPIO_USART0_RTSROUTE - RTS port/pin select ..............785
24.6.109 GPIO_USART0_RXROUTE - RX port/pin select ...............786
24.6.110 GPIO_USART0_CLKROUTE - CLK port/pin select ..............786
24.6.111 GPIO_USART0_TXROUTE - TX port/pin select ...............787
24.6.112 GPIO_USART1_ROUTEEN - USART1 pin enable ..............787
24.6.113 GPIO_USART1_CSROUTE - CS port/pin select ...............788
24.6.114 GPIO_USART1_CTSROUTE - CTS port/pin select ..............788
24.6.115 GPIO_USART1_RTSROUTE - RTS port/pin select ..............789
24.6.116 GPIO_USART1_RXROUTE - RX port/pin select ...............789
24.6.117 GPIO_USART1_CLKROUTE - CLK port/pin select ..............790
24.6.118 GPIO_USART1_TXROUTE - TX port/pin select ...............790
24.6.119 GPIO_USART2_ROUTEEN - USART2 pin enable ..............791
24.6.120 GPIO_USART2_CSROUTE - CS port/pin select ...............791
24.6.121 GPIO_USART2_CTSROUTE - CTS port/pin select ..............792
24.6.122 GPIO_USART2_RTSROUTE - RTS port/pin select ..............792
24.6.123 GPIO_USART2_RXROUTE - RX port/pin select ...............793
24.6.124 GPIO_USART2_CLKROUTE - CLK port/pin select ..............793
24.6.125 GPIO_USART2_TXROUTE - TX port/pin select ...............794
silabs.com | Building a more connected world. Rev. 0.4 | 19

25. LDMA - Linked DMA ...........................795
25.1 Introduction..............................795
25.1.1 Features .............................796
25.2 Block Diagram.............................797
25.3 Functional Description ..........................798
25.3.1 Channel Descriptor .........................798
25.3.2 Channel Configuration ........................803
25.3.3 Channel Select Configuration ......................803
25.3.4 Starting a transfer ..........................803
25.3.5 Managing Transfer Errors .......................804
25.3.6 Arbitration .............................804
25.3.7 Channel descriptor data structure .....................806
25.3.8 Interaction with the EMU ........................809
25.3.9 Interrupts .............................810
25.3.10 Debugging ............................810
25.4 Examples ..............................810
25.4.1 Single Direct Register DMA Transfer ....................810
25.4.2 Descriptor Linked List .........................811
25.4.3 Single Descriptor Looped Transfer ....................813
25.4.4 Descriptor List with Looping .......................814
25.4.5 Simple Inter-Channel Synchronization ...................815
25.4.6 2D Copy .............................817
25.4.7 Ping-Pong ............................819
25.4.8 Scatter-Gather ...........................820
25.5 LDMA Source Selection Details .......................820
25.5.1 LDMA Source Selection Details .....................821
25.6 Register Map .............................823
25.7 Register Description ...........................826
25.7.1 LDMA_IPVERSION - DMA Channel Request Clear Register ...........826
25.7.2 LDMA_EN - DMA module enable disable Register ...............826
25.7.3 LDMA_CTRL - DMA Control Register ...................827
25.7.4 LDMA_STATUS - DMA Status Register...................828
25.7.5 LDMA_SYNCSWSET - DMA Sync Trig Sw Set Register .............829
25.7.6 LDMA_SYNCSWCLR - DMA Sync Trig Sw Clear register ............829
25.7.7 LDMA_SYNCHWEN - DMA Sync HW trigger enable register ...........830
25.7.8 LDMA_SYNCHWSEL - DMA Sync HW trigger selection register ..........831
25.7.9 LDMA_SYNCSTATUS - DMA Sync Trigger Status Register ............832
25.7.10 LDMA_CHEN - DMA Channel Enable Register ................832
25.7.11 LDMA_CHDIS - DMA Channel Disable Register ...............833
25.7.12 LDMA_CHSTATUS - DMA Channel Status Register ..............833
25.7.13 LDMA_CHBUSY - DMA Channel Busy Register ...............834
25.7.14 LDMA_CHDONE - DMA Channel Linking Done Register (Si..............835
25.7.15 LDMA_DBGHALT - DMA Channel Debug Halt Register .............836
25.7.16 LDMA_SWREQ - DMA Channel Software Transfer Request..............836
25.7.17 LDMA_REQDIS - DMA Channel Request Disable Register ............837
25.7.18 LDMA_REQPEND - DMA Channel Requests Pending Register ..........837
silabs.com | Building a more connected world. Rev. 0.4 | 20