Silicon Laboratories Si86xxT-EVB User manual

UG130: Si86xxT-EVB User's Guide
The Si864xxT devices, the latest addition to the Si86xx isolator family, are 4-channel
CMOS-based galvanic digital isolators surge rated at 10 kV. Operating up to 150 Mbps,
they are available in wide body 16-pin SOIC packages and designed for the stringent
isolation needs of the industrial, commercial, and automotive markets. Various channel
configurations dictating the number of reverse channels and default output states are
also available per the Si86xx data sheet’s ordering guide.
The Si864xxT-EVB allows designers to quickly evaluate the Si8642ET’s capabilities
and functionality, either by driving inputs to logic low via shunts, or injecting signals to
the header pins via single wires or a 2x6 ribbon cable (not included).
For more information on our Si86xxT isolators, visit the Silicon Labs website at: http://
www.silabs.com/isolation. The product data sheet and application notes can be refer-
enced to help facilitate designs.
KEY POINTS
• Discusses kit contents and equipment.
•Describes hardware setup and
demonstration.
• Shows EVB schematic and layout.
• Includes bill of materials and the ordering
guide for Si864xxT-KIT.
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1

1. Kit Contents
The Si864xxT Evaluation Kit contains the following items:
•Si864xxT-EVB evaluation board, shown in the figure below.
• Si8642ET-IS, 4-channel (Reverse: 3 and 4), 150 Mbps, 10 kV, Wide Body, Default High I/O.
Figure 1.1. Si86xxT-EVB
UG130: Si86xxT-EVB User's Guide
Kit Contents
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 1

2. Required Equipment
The following equipment is required to demonstrate the evaluation board:
•Two DC Power supplies 2.5–5.5 V, 100 mA.
• (Optionally) Isolated from one another.
• Four banana-to-test-clip cables with clips to supply power to the board.
• Two 2-pin header shunts (included).
• One DMM.
• One DMM Voltage Probe Set.
2.1 Optional Equipment
The following equipment is optional and can be used to demonstrate more of the evaluation board functionalities, including signal prop-
agation statistics:
• One Signal generator.
• Two BNC Coaxial cables.
• One BNC splitter.
• One BNC to test-clip connector.
• One 2-Channel Oscilloscope.
• One 10x Voltage Probe.
UG130: Si86xxT-EVB User's Guide
Required Equipment
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 2

3. Hardware Setup and Demonstration
3.1 Powering the Supplies
Both sides of the Si8642ET isolator accept supplies between 2.5-5.5 V. See the figure below.
Perform the following steps to set up the Si864xxT-EVB:
• Remove all shunts.
• Power Side-A.
• Clip 5.0 V from the first power supply to TP1 (VDD1) and its GND to TP3 or TP5 (GND1).
• LED, D1, will light up, confirming power is supplied.
• Power Side-B.
• Clip 5.0 V from the second power supply to TP2 (VDD2) and its GND to TP4 or TP6 (GND2).
• LED, D2, will light up, confirming power is supplied.
Figure 3.1. EVB — Powered Up
3.2 DC Signal Demonstration
3.2.1 Defaults
The default output signal state of the Si8642ET is a logic High, meaning that with all shunts removed (EN1 and EN2 floating), all digital
inputs (A1, A2, B3, B4) and all digital outputs will (B1, B2, A3, A4) will be at their respective High voltage level. These values can be
measured and confirmed using the DMM.
• Remove all shunts.
• Measure with the DMM that all digital inputs (A1, A2, B3, B4) are logic High.
• Measure with the DMM that all digital outputs (B1, B2, A3, A4) are logic High.
See Figure 3.1 EVB — Powered Up on page 3.
UG130: Si86xxT-EVB User's Guide
Hardware Setup and Demonstration
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 3

3.2.2 Fail-safes
When power is removed from one side of the isolator, the outputs at the other side of the isolator default to logic High.
•A-side
• Remove all shunts.
• Remove A-side power supply.
• Measure B-side outputs, B1 and B2 and see that they are logic High.
• Replace A-side power and see B1 and B2 driven to their appropriate states.
• B-side
• Remove all shunts.
• Remove B-side power supply.
• Measure A-side outputs, A3 and A4 and see that they are logic High.
• Replace B-side power and see A3 and A4 drive to their appropriate states.
Figure 3.2. EVB — Failsafe, No VDDA
UG130: Si86xxT-EVB User's Guide
Hardware Setup and Demonstration
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 4

3.2.3 Configured
For an example, see the figure below.
•Place a shunt across J1 at A2.
• This produces a logic Low input on forward channel A2. The SI88642ET will transmit this to the B-side, and the corresponding
logic Low can be observed and measured with the DMM on J2, B2.
• Place a shunt across J2 at B3.
• This produces a logic Low input on reverse channel B3. The SI88642ET will transmit this to the A-side, and the corresponding
logic Low can be measured with the DMM on J1, A3.
Figure 3.3. EVB Configured for DC Signal Demonstration without Enable
UG130: Si86xxT-EVB User's Guide
Hardware Setup and Demonstration
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 5

3.2.4 Utilizing Enable
For an example, see the figure below.
•Place a shunt across J1 at A2.
• This produces a logic Low input on forward channel A2. The SI88642ET will transmit this to the B-side, and the corresponding
logic Low can be observed and measured with the DMM on J2, B2.
• Place a shunt across J2 at EN2.
• This drives EN2 to a logic Low input which tri-states outputs B1 and B2. A Hi-Z output can be observed on outputs B1 and B2
with the DMM (appearing as a high), even while A1 is a logic Low and A2 is a logic High.
Figure 3.4. EVB Configured for DC Signal Demonstration with Enable
UG130: Si86xxT-EVB User's Guide
Hardware Setup and Demonstration
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 6

3.3 Optional Dynamic Signal Demonstration
Note: Logic inputs should NOT exceed the respective VDD.
For an example, see the figure below.
•Remove all shunts.
• Setup signal generator and oscilloscope.
• Generate 0 V to VDD1 peak, square wave (up to 300 MHz, but within the oscilloscope’s capabilities) on the signal generator.
• Split the signal generator output to two separate BNC cables via the splitter.
• Attach one BNC cable end to oscilloscope Channel 1 and configure the channel for 1x gain.
• Attach the 10x oscilloscope probe to oscilloscope channel 2 configure the channel for 10x gain.
• Connect the remaining BNC cable end to the BNC-to-test-clip adapter.
• Clip the signal generator’s output to A2 relative to GND1 (via either TP5 or TP3).
• Clip the oscilloscope probe’s signal line on B1 and reference to GND2 (via either TP4 or TP6).
• Observe Channel 1 (input – A2) and Channel 2 (output – B2) on the oscilloscope for various parametrics such as skew and jitter.
Figure 3.5. EVB Configured for Dynamic Signal Demonstration without Enable
UG130: Si86xxT-EVB User's Guide
Hardware Setup and Demonstration
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 7

4. Schematics
Figure 4.1. Si86xxT-EVB Schematic
UG130: Si86xxT-EVB User's Guide
Schematics
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 8

5. Layout
Figure 5.1. EVB — Top Silk
Figure 5.2. EVB — Bottom Silk
UG130: Si86xxT-EVB User's Guide
Layout
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 9

Figure 5.3. EVB — Top Copper
Figure 5.4. EVB — Bottom Copper
UG130: Si86xxT-EVB User's Guide
Layout
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 10

6. Bill of Materials
Table 6.1. Si86xxT-EVB Bill of Materials
Item No. Quantity Reference Value Manufacturer PN Manufacturer
1 2 C1, C4 1 μF CL21B105KBFNNNE Samsung
2 2 C2, C3 0.1 μF C0603X7R500-104K Venkel
3 2 D1, D2 RED LTST-C190KRKT LITE-ON TECHNOLOGY CORP
4 2 J1, J2 HEADER 6x2 TSW-106-07-T-D Samtec
5 2 JS1, JS2 Jumper Shunt SNT-100-BK-T Samtec
6 1 PCB1 Si864xxT-EVB
REV 1.0
Si864xxT-EVB REV 1.0 SiLabs
7 2 R1, R2 10K CR0603-10W-103J Venkel
8 12 R3, R4, R5, R6, R7,
R8, R9, R10, R11,
R12, R13, R14
499 CR0603-10W-4990F Venkel
9 4 SF1, SF2, SF3, SF4 BUMPER SJ61A6 3M
10 2 TP1, TP2 WHITE 151-201-RC Kobiconn
11 4 TP3, TP4, TP5, TP6 BLACK 151-203-RC Kobiconn
12 1 U1 Si8642ET Si8642ET-IS SiLabs
UG130: Si86xxT-EVB User's Guide
Bill of Materials
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 11

7. Ordering Guide
Ordering Part Number (OPN) Description
Si864xxT-KIT Si8642ET 4-channel 10 kV Isolator Evaluation Kit
UG130: Si86xxT-EVB User's Guide
Ordering Guide
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 12

Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Smart.
Connected.
Energy-Friendly
Products
www.silabs.com/products
Quality
www.silabs.com/quality
Support and Community
community.silabs.com