SilverBolt 1620-SA User manual

REV 10/19/2021
IMPORTANT BULLETIN ABOUT PRESSURE ADJUSTMENT
CONGRATULATIONS on your NEW SilverBolt 1620-SA!
We have preset your pressure setting to the medium range needed for most heat
transfer applications. This is the appropriate setting for pressing single layers of fabric
or other thin items. Your heat press works like a fulcrum. Putting thicker materials in
the heat press multiplies the closing force. If you place thick items like mouse pads
or hoodies in the press, you must reduce the pressure setting. If you place thick items
in the press without reducing the pressure setting, the applied clamping force will be
too high. You may damage the heat press.
We hope you enjoy your new heat press for years to come. To help you get the most
out of your new heat press, we’ve inserted this important bulletin.
The mouse pad and shirt both may need a medium
pressure for the transfer, but since the mouse pad is
thicker than the shirt, the pressure must be reduce to
press.
For more information about your new
heat press, scan the code to go to the
blog article. If you can not scan the code,
please visit,
https://blog.signwarehouse.com/silver-
bolt-1620sa-heat-press
Mouse Pad
Shirt
SilverBolt 1620-SA Caddie Assembly Instruction
4PCS M8 x 20mm Bolt (Working Table)
3PCS M8 x 35mm Bolt (Seat Connector)
3PCS M5 x 12mm Screw (Column Washer)
5PCS M8 x 55mm Bolt (Upper Connector)
Parts List
Item Name
Stand Leg w/Wheel 5
5
1
1
1
1
1
3
4
3
7
3
17
17
Lower Connector
Upper Connector
Column Washer
Aluminum Column
Seat Connector
Working Table/Machine Body
M5 x 12mm Screw (Column Washer)
M8 x 20mm Bolt (Working Table)
M8 x 35mm Bolt (Seat Connector)
(Lower Connector)
(Upper Connector)
M8 x 55mm Bolt
M8 x 65mm Bolt (Aluminum Column)
M8 Flat Washer (Under Spring Washer)
M8 Spring Washer (Above Spring Washer)
Quantity
3PCS M8 x 65mm Bolt (Aluminum Column)
2PCS M8 x 55mm Bolt (Lower Connector)
Seat Connector
Column Washer
Upper Connector
Stand Leg w/ Wheel
Lower Connector
Aluminum Column

1) Start with the Upper and Lower Connector and the 5 legs. You
will want to note where the two raised holes are and then turn
the Upper connector over and place the legs inside (See FIG
1). Take the Lower connector and place on top of the legs. You
may need an extra hand or two to hold the legs to thread the
bolts through the Lower connector. All the legs must be under
the Lower connector before putting the bolts in. You will need
to make sure the bolts, M8 x 55mm, are not too tight. (FIG 2)
2) Once the Lower connector is attached, turn it over. Now take
(5) M8 x 55mm bolt and tighten the legs to the connectors.
(FIG 3 next page).
NOTE: The Base must be installed in stages, and the column must be installed correctly. Two people
maybe needed for construction of the base.
NO. Name QTY NO. Name QTY
2
3
Upper Connector
Lower Connector
11
1
1
1
1
1
5
3
3
7
3
4
17
17
Aluminum Column
4
5
6
7
9
10
8
11
12
13
14
Column Washer
Seat Connector
Stand Leg w/ Wheel
Hex Tool
M8 x 65mm Bolt
M8 x 55mm Bolt
M5 x 12mm Screw
M8 x 35mm Bolt
M8 x 20mm Bolt
M8 Flat Washer
M8 Lock Washer
12
7
9
10
* You will need a Phillips screwdriver and a Level. These are not included with your stand
11 12
13 14
8 6
3 4 5
Align one of the notches in the bottom of
the column over one of the bolts in the
base plate. Then thread the three bolts
through the bottom of the base plate into
the bottom of the column. Do not
over-tighten.
FIG 4 FIG 5
It’s a good idea to use a carpenter’s level to check
the vertical alignment of the column. Place it on the
top of the column after installation to ensure a level
platform for the top mounting plate and the heat
press.
FIG 2
FIG 1
FIG 3
3) Take the Column Washer and screw on the top of the Upper Connector. (See Fig 3)
4) Make sure the column (1) is installed with the two notches on the bottom. The flat surface is the
top.
5) Align ONE of the notches over one of the bolts in the base plate (2). See Fig 4 below.
6) When inserting the three bolts (9) through the bottom of the base plate and into the bottom of the
column, do not over-tighten these bolts. If over-tightened, the column may tilt slightly.
When properly installed, the column will be level. Check with a level on top of the column, or
on top of the top mounting support (5), as seen in Fig 5 below. If the column or top
mounting support are not level, adjust the screws securing the column to the base.