Silvercrest 326698 User manual

WIRELESS OPTICAL MOUSE/
WIRELESS OPTICAL MOUSE
Operation and safety notes
FCC ID: YVYHM-R046
FCC ID: YVYHM8187
Version / Versión: 07 / 2019
Made in / Hecho en: China

US-EN Operation and safety notes Page 3

3US-EN
Description of signal words ........................... Page 4
Customer service ................................................ Page 4
List of pictograms used .................................... Page 5
Introduction .......................................................... Page 5
Intended use......................................................... Page 5
Trademark notices ............................................. Page 6
Scope of delivery ............................................... Page 6
Important safety notes.................................... Page 7
Safety warnings for batteries ...................... Page 9
Description of parts........................................... Page 14
Technical data...................................................... Page 16
Before use ............................................................. Page 17
Operation.............................................................. Page 18
Software installation........................................ Page 19
Storage when not in use................................. Page 20
Cleaning ................................................................. Page 21
Troubleshooting.................................................. Page 21
Disposal.................................................................. Page 21
Three year limited warranty......................... Page 22

4US-EN
DESCRIPTION OF SIGNAL WORDS
WARNING indicates a hazardous situation that, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury.
NOTICE indicates information considered important, but not
hazard related (e.g. messages related to property damage).
CUSTOMER SERVICE
Visit a LIDL store for further assistance.
Please have your IAN number ready.
IAN 326698
Call customer service at 1 [phone]
Visit the Website Customer Service Platform at
www.lidl.com/contact-us

5US-EN
WIRELESS OPTICAL MOUSE
PIntroduction
Congratulations on your purchase. You have selected a quality
product. The instructions for use are a part of the product.
They contain important information about the safety, use and
disposal of the product. Before using the product, please learn
about all the safety information and usage instructions. Only
use the product as described and for the specified applications.
If you lend the product to someone else, please also give all the
instructions.
PIntended use
This WIRELESS OPTICAL MOUSE (hereinafter referred to as
“product”)is an information technology device and is designed
as an input device for computers. This product must not be used
outside of closed rooms. This product is not intended for use in
LIST OF PICTOGRAMS USED
NOTE: This symbol with the signal
word “NOTE“ provides additional useful
information.
V Voltage (direct current)
Warning against optical radiation

6US-EN
companies or for other commercial uses (e.g. office productivity
applications). Use this product only in the home for private
purposes Any other use is considered improper. Any claims
resulting from improper use or due to unauthorised modification
of the product will be considered un-warranted. Any such use is
at your own risk.
PTrademark notices
USB®is a registered trademark of USB Implementers
Forum, Inc.
Windows®is a registered trademark of Microsoft
Corporation in the United States and other countries.
Mac OS is trademarks of Apple Inc., registered in the U.S.
and other countries.
The SilverCrest trademark and trade name is the property of
their respective owners.
Any other names and products are trademarks or registered
trademarks of their respective owners.
PScope of delivery
1 Wireless optical mouse
1 USB dongle
1 CD-ROM installation software
2 Batteries (AA)
1 Instructions for use

7US-EN
IMPORTANT SAFETY NOTES
READ ALL INSTRUCTIONS. KEEP FOR FUTURE REFERENCE.
INCLUDE ALL DOCUMENTATION WHEN PASSING THIS
PRODUCT ON TO OTHERS.
WARNING! DANGER TO LIFE AND RISK OF
ACCIDENT FOR INFANTS AND CHILDREN!
DANGER! RISK OF SUFFOCATION! Never leave
children unsupervised with the packaging material. The
packaging material poses a suffocation hazard. Children
frequently underestimate the dangers. The packaging
material is not a toy.
This product may be used by children age 8 years and up,
as well as by persons with reduced physical, sensory or
mental capacities or lacking experience and/or knowledge,
so long as they are supervised or instructed in the safe use
of the product and understand the associated risks. Do not
allow children to play with the product. Cleaning and user
maintenance should not be performed by children without
supervision. The product is not a toy.
DANGER! Some of the provided parts can
be swallowed. If a part is swallowed, seek
immediate medical attention.
DANGER! Radio interference
Switch the product off on aeroplanes, in hospitals, service
rooms, or near medical electronic systems. The wireless
signals transmitted could impact the functionality of sensitive
electronics.

8US-EN
Keep the product at least 7.87 in (20 cm) from pacemakers
or implantable cardioverter defibrillators, as the
electromagnetic radiation may impair the functionality of
pacemakers.
The radio waves transmitted could cause interference in
hearing aids.
Do not place the product near flammable gasses or
potentially explosives areas (e.g. paint shops) with the
wireless components on, as the radio waves emitted can
cause explosions and fire.
The range of the radio waves varies by environmental
conditions. In the event of wireless data transmission,
unauthorised third parties receiving the data cannot be
excluded.
DANGER! Keep batteries out of reach of
children. If accidentally swallowed seek
immediate medical attention.
DANGER! EXPLOSION HAZARD!
Never recharge non-rechargeable batteries. Do not
short-circuit batteries or open them. Overheating, fire or
bursting can be the result. Never throw batteries into fire
or water. Do not exert mechanical loads to batteries.
WEAR PROTECTIVE GLOVES!
Leaked or damaged batteries can cause burns on
contact with the skin. Wear suitable protective gloves at
all times if such an event occurs.

9US-EN
Safety warnings for batteries
When used correctly, cells and batteries provide a safe and
dependable source of portable power. However, if they are
misused or abused, this may result in leakage, burns, fire, or
explosion.
Store batteries in a dry place at room temperature. Batteries
are sensitive to high and low temperatures. Such thermal
exposure may lead to leakage, fire, or explosion.
Keep cells and batteries out of reach of children, especially
small batteries. Ingestion may lead to choking or acute and
serious personal injury.
Keep cells or batteries clean and dry both during use and
storage. Wipe metal terminals with a soft, dry cloth if they
become dirty.
Immediately seek medical attention if a cell or battery has
been swallowed. Also, contact your local poison control
center.
In the event that the electrolyte comes into contact with the
skin or eyes, immediately flush with fresh water for at least
15 minutes and seek medical attention.
Store unused batteries in their original packaging or in safe
place and away from metal objects that may short-circuit
them.
Exercise care in handling batteries in order to prevent
shorting with conducting materials, such as rings, coins,
bracelets, and keys. The battery or the conductor can
overheat and cause burns, leakage, fire, or explosion.

10 US-EN
Clean the battery contacts and also those of the product
prior to battery installation. Keep the contacts clean.
Remove batteries from the product that will not be used for
an extended period of time (months or longer).
Remove discharged batteries from product promptly to avoid
possible damage from leakage.
Choose the proper battery for the intended application.
Always take care to correctly insert batteries observing (+)
and (-) polarity marks on the battery and the product for
which it is intended. Proper polarity must be observed to
avoid damage to either product or batteries.
Always replace the whole set of batteries at one time, taking
care not to mix old and new ones, or batteries of different
types, capacities, or manufacturers.
Never heat batteries in order to revive them.
Never charge a battery unless the battery label specifically
states the battery is rechargeable. Charging a non-
rechargeable battery, may result in leakage, fire, or
explosion.
Do not drop or subject the cell or battery to strong
mechanical shock.
Batteries should not be disassembled, crushed, punctured, or
otherwise mutilated. Such abuses may result in leakage, fire,
or explosion.
Do not dispose of the battery in a fire. Failure to observe this
precaution may result in an explosion.

11US-EN
Dispose of batteries properly and in accordance with
government regulations.
ATTENTION! RISK OF PROPERTY DAMAGE
Check the product before every use! Discontinue use if any
damage to the product is detected!
This product does not contain any parts which can be
serviced by the user.
Do not place burning candles or other open fire on or next
to the product.
Sudden temperature changes may cause condensation
inside the product. In this case, allow the product to
acclimate for some time before using it again to prevent
short circuits!
Do not operate the product near heat sources, e.g. radiators
or other devices emitting heat!
Do not throw the product into fire and do not expose to high
temperatures.
Never open the product!! It has no internal parts requiring
maintenance.
ATTENTION! Ensure that
no direct heat sources (e.g. heating) can affect the product.
any contact with splashed and dripping water and corrosive
liquids is avoided and the product is not operated in the
vicinity of water. In particular, the product should never be
submerged in liquid; do not place any vessels filled with
liquid, for example, vases or drinks, on or near the product.
the product is not used in the immediate vicinity of magnetic
fields (e.g. speakers).

12 US-EN
no fire sources (e.g. burning candles) are placed on or near
the product.
no objects are inserted into the interior of the product.
the product is never subjected to excessive shocks and
vibrations.
Take care to avoid injury to eyes and skin when in
the vicinity of optical radiation
NOTE:
The user must take regular breaks during the use of the product,
in case of pain in the hands, arms or shoulder and neck area
the work must be interrupted and some stretching exercises must
be done.
It is necessary to repair the product if they have been
damaged in any way, for example, if the housing is
damaged, if liquid or objects have penetrated the product or
if the product has been exposed to rain or moisture.
Repair work is also required if the product is not working
properly or has been dropped. If smoke is produced, or
there are any unusual sounds or smells, turn the product
off immediately. In such cases, the product should not be
used until they have been inspected by authorised service
personnel. Only have the product repaired by qualified
personnel. Never open the housing of the product.
Changes or modifications to this product not expressly
approved by the party responsible for compliance could
void the user‘s authority to operate the product.
NOTE: This product has been tested and complies with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.

13US-EN
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
product generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this product causes
harmful interference to radio or television reception, which
can be determined by turning the product off and on, the
user is encouraged to try and correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and
receiver.
• Connect the equipment to an outlet on a different circuit
than the one the receiver is connected to.
• Consult the dealer or an experienced radio / TV
technician for help.
This product complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This product may not cause harmful interference.
2. This product must accept any interference received,
including interference that may cause undesired
operation.
The Lidl US, LLC is not responsible for interference with
radios or televisions due to unauthorised modification of the
product.
The Lidl US, LLC further assumes no liability for using or
replacing cables and products not distributed by Lidl US,

14 US-EN
LLC. The user of the product is fully responsible for correcting
interference caused by such unauthorised modification of
the product, as well as replacement of such products.
SAVE THESE INSTRUCTIONS
PDescription of parts
1Right mouse button 7Battery compartment cover
2DPI button 8Instructions for use
3Backward button 9USB dongle
4Forward button 10
Software CD
5Left mouse button 11
2 x AA batteries
6Scroll wheel and middle mouse button

15US-EN
DPI
DPI
8
3
2
9
10
11
6
5
4
7
1
1000 DPI
1500 DPI
2000 DPI
A
B

16 US-EN
PTechnical data
Voltage supply: 2 x 1.5 V, AA batteries
Operation time: 3 to 6 months (Alkaline battery)
Operating Systems: Windows®7 / 8 / 10, XP, Vista
Resolution: 1000 / 1500 / 2000 dpi
Wireless range: 5 m
Radio frequency band: 2408 - 2474 MHz
USB version: 2.0
Hardware: 1 free USB port available
Operating temperature: 5 to 35 °C
Storage temperature: 0 to 45 °C
Storage humidity: 10 to 70 % RH
Dimension (L x W x H): 3.98 x 2.6 x 1.61 in,
(101 x 66 x 41 mm)
Net weight: 0.26 lbs, (115g)
The specification and design may be changed without
notification.

17US-EN
PBefore use
NOTE:
Before use, verify the package contents are complete and
undamaged!
All parts have to be unpacked and the packaging material
has to be removed completely.
Setting up your mouse –
inserting/replacing the battery
Remove the battery compartment
cover
7
.
Insert 2 AA batteries
11
into the battery compartment .
Ensure that the polarities are correct
(+/–).
Reinsert the battery compartment
cover
7
and push it down until it locks
in place.

18 US-EN
POperation
Connecting the USB dongle
9
:
Slot the USB dongle
9
into a
spare USB port on your computer.
Turn your computer on.
The necessary drivers are
automatically installed.
1
Right mouse button:
Provides traditional mouse
click functions.
2
DPI button:
(1000 / 1500 / 2000
– Click button once, then
change DPI setting to next
DPI value). The default DPI
setting is 1500 dpi. Choose
a setting that is comfortable
for you.
3
Backward button
4
Forward button
5
Left mouse button:
Provides traditional mouse functions like click, double click
and drag.
6
Scroll wheel and middle mouse button:
Roll up or down to scroll through pages or documents.
65 1
4
3
2

19US-EN
PSoftware installation
NOTE:
The software is not compatible with MAC OS.
You can also download the mouse installation software at
www.Lidl-service.com. At this Lidl service website you have
to input the product number IAN 326698 to search for the
software to download.
Software installation from CD
3. Insert the provided Setup Disc into the computer’s CD
rom.
4. The installation process should start automatically.
5. If this is not the case, start the file “SFM 4 C2 Mouse
Setup.exe“ manually on the CD-ROM by double-
clicking.
6. Follow the installation instructions to complete the whole
installation process.
7. After installing and running the application software
program, you will find the below user interface.

20 US-EN
Configuration of the individual mouse buttons
You can use the software to control the functions of the mouse
buttons customize to your wishes.
The configuration menu of the mouse appears.
Select on left column for which button you would like to
change its setting. Here you can now setup each one button
setting for those five individual buttons’ function.
Click on “Button Setting” and then select one function from
the menu.
To activate the changes, click the “OK“ button
With the button “Restore defaults“ you can put the buttons of
the wireless mouse back to the initial delivery state.
Below other tabs of this configuration menu contain the
configuration options of the respective operating system. You
can adjust mouse button setup to your desired mouse setting at
“Advanced Setting”.
Pointer
Scrolling
Double-Click
PStorage when not in use
Batteries must be removed before storage.
Store the product in a dry indoor location protected from
direct sunlight, preferably in its original packaging.