Silvercrest 365241 2101 User manual

CORDLESS WET & DRY HAND-HELD VACUUM CLEANER
AKKU-HANDSTAUBSAUGER
ASPIRATEUR À MAIN SANS FIL SAST 18 A1
IAN 365241_2101
ASPIRATEUR À MAIN SANS FIL
Mode d’emploi
CORDLESS WET & DRY
HAND-HELD VACUUM CLEANER
Operating instructions
ACCU-HANDSTOFZUIGER
Gebruiksaanwijzing
AKU RUČNÍ VYSAVAČ
Návod k obsluze
BATTERIDREVET HÅNDSTØVSUGER
Betjeningsvejledning
RUČNÝ VYSÁVAČ
Návod na obsluhu
AKKU-HANDSTAUBSAUGER
Bedienungsanleitung
ODKURZACZ AKUMULATOROWY
Instrukcja obsługi
ASPIRADOR RECARGABLE DE MANO
Instrucciones de uso

GB / IE Operating instructions Page 1
DE / AT / CH Bedienungsanleitung Seite 21
FR / BE Mode d’emploi Page 41
NL / BE Gebruiksaanwijzing Pagina 63
CZ Návod k obsluze Strana 83
PL Instrukcja obsługi Strona 103
SK Návod na obsluhu Strana 123
ES Instrucciones de uso Página 143
DK Betjeningsvejledning Side 163
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l‘appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas
las funciones del dispositivo.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

4
1 2
q
0
8
6
3
5
9
w
r
e
7
t
z
u
i

GB│IE │ 1 ■SAST 18 A1
Contents
Introduction...................................................2
Intended use ..................................................2
Package contents ..............................................2
Appliance description...........................................3
Technical data .................................................4
Important safety instructions.....................................6
Beforefirstuse ................................................9
Information about the batteries .................................10
Installation of the wall bracket ..................................10
Charging ....................................................11
Operation ...................................................12
Using accessories .............................................14
Crevice tool ............................................................14
Universal nozzle ........................................................14
Precision nozzle.........................................................14
Small brush attachment ...................................................14
Wet-suction nozzle.......................................................14
Motorised brush attachment ...............................................14
Cleaning.....................................................15
Emptying the dirt container and cleaning the filter ..............................15
Cleaning the brush attachment ............................................. 16
Cleaning the appliance ...................................................16
Storage .....................................................16
Disposal .....................................................17
Disposal of the appliance ................................................. 17
Disposal of packaging....................................................17
Ordering replacement parts ....................................18
Kompernass Handels GmbH warranty............................18
Service................................................................ 20
Importer ............................................................... 20
IB_365241_SAST18A1_LB8.indb 1 10.06.2021 10:37:17

■ 2 │ GB│IE SAST 18 A1
Introduction
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions are part of
this product. They contain important information about safety, usage and
disposal. Before using the product, please familiarise yourself with all operating
and safety instructions. Use the product only as described and for the range of
applications specified. Please also pass these operating instructions on to any
future owner.
Intended use
This handheld vacuum cleaner may only be used to vacuum dry or wet surfaces,
dry or wet materials and liquids.
Do not vacuum people or animals with this appliance. Any other usage or
modification of the appliance is deemed to be improper and carries a significant
risk of accidents.
The manufacturer accepts no liability for damages that result from improper use
of the appliance or are caused by the incorrect operation of it. The appliance is
not intended for commercial use.
Package contents
The appliance is supplied with the following components as standard:
▯ Cordless wet and dry Hand-Held Vacuum Cleaner
▯ Crevice tool
▯ Universal nozzle
▯ Precision nozzle
▯ Small brush attachment
▯ Wet-suction nozzle
▯ Motorised brush attachment
▯ Wall bracket
▯ Installation materials (2 screws, 2 wall plugs)
▯ Mains adapter
▯ Operating instructions
NOTE
► Check the package for completeness and signs of visible damage.
► If the delivery is incomplete or damage has occurred as a result of
defective packaging or during transport, contact the Service hotline
(see section Service).
IB_365241_SAST18A1_LB8.indb 2 10.06.2021 10:37:18

GB│IE │ 3 ■SAST 18 A1
Appliance description
1Crevice tool
2 Universal nozzle
3Precision nozzle
4Small brush attachment
5Wet-suction nozzle
6Motorised brush attachment
7Wall bracket
8Accessories holder
9Barrel plug
0Mains adapter
qOn/Off switch
wCharge indicator lamp
eRelease button
rMotor unit
t Working light
zHEPA filter
u Filter holder
i Dirt container
NOTE
► This appliance is supplied with non-charged batteries. The batteries must be
charged before first use.
IB_365241_SAST18A1_LB8.indb 3 10.06.2021 10:37:18

■ 4 │ GB│IE SAST 18 A1
Technical data
Mains adapter
Manufacturers
Zhejiang Mootree Electronic Technology Co., Ltd.
No. 36-1 Tongji Street, Nanmingshan Street,
Liandu District 323000 Lishui City,
Zhejiang, China
Commercial register number:
91331127MA2E1A6T1D
Importer:
KOMPERNASS HANDELS GMBH,
BURGSTRASSE 21,44867 BOCHUM,
GERMANY
Register court: AG Bochum
Register number: HRB 4598
Model SEU012A-225050
Input voltage 100-240 V ~(AC)
Input AC frequency 50-60 Hz
Output voltage 22.5 V (DC)
Output current 0.5 A
Output power 11.25 W
Average operating
efficiency 84.9 %
Low load efficiency (10%) 80.4 %
No-load power
consumption 0.05 W
Input current 0.4 A
Polarity
Protection class II / (double insulation)
Efficiency class 6VI
Protection type IP 20: Protection against solid foreign objects
with a diameter of more than 12.5 mm
IB_365241_SAST18A1_LB8.indb 4 10.06.2021 10:37:23

GB│IE │ 5 ■SAST 18 A1
Batteries
Capacity 2200 mAh
Rechargeable battery 18.5 V (DC)
(5 x 3.7 V lithium-ion battery)
Appliance
Input voltage 22.5 V (DC)
Input current 0.5 A
Polarity
Motorised brush attachment
Input voltage 18 V (DC)
Power consumption 10 W
NOTE
► No user action is required to switch the product between 50 and 60 Hz.
The product adapts automatically to either 50 or 60 Hz.
IB_365241_SAST18A1_LB8.indb 5 10.06.2021 10:37:23

■ 6 │ GB│IE SAST 18 A1
Important safety instructions
DANGER! ELECTRIC SHOCK!
► Do not charge or use the appliance outdoors.
► Never use the handheld vacuum cleaner if the cable, plug
or casing are damaged.
► To avoid risks, arrange to have damaged power cables
and/or plugs replaced as soon as possible by a qualified
specialist.
► Have all repairs carried out by a specialist workshop.
Under no circumstances should you open the appliance
yourself. Repairs that are not carried out by a specialist
workshop could lead to physical injuries.
► Never touch the mains adapter or the appliance with wet
or damp hands.
► Do not use the mains adapter with an extension cable;
connect the mains adapter directly to a power socket.
WARNING! RISK OF INJURY!
► Do not change any accessories while the appliance is
switched on.
► Do not use the handheld vacuum for vacuuming up sharp
objects or glass shards.
► Never vacuum up burning matches, glowing ashes or
cigarette butts.
► Do not use the handheld vacuum for vacuuming up
chemical products, stone dust, gypsum, cement or similar
particles.
► This appliance is not suitable for use with inflammable and
explosive substances or chemical and aggressive liquids.
► Always store the appliance indoors. To prevent accidents,
keep the appliance in a dry location when not in use.
IB_365241_SAST18A1_LB8.indb 6 10.06.2021 10:37:23

GB│IE │ 7 ■SAST 18 A1
WARNING! RISK OF INJURY!
► Under extreme conditions, leaks in the battery cells may
occur. In the event that battery fluid comes into contact
with skin or eyes, the affected area must be rinsed off with
water immediately. Contact a physician.
► This appliance may be used by children aged 8 years and
above and by persons with limited physical, sensory or
mental capabilities or lack of experience and knowledge,
provided that they are under supervision or have been told
how to use the appliance safely and are aware of the
potential risks.
► Do not allow children to use the appliance as a toy.
► Cleaning and user maintenance tasks may not be carried
out by children unless they are supervised.
► Take special care when using the hand vacuum on stairs.
► Never reach into moving/rotating parts.
There is a risk of crushing injury!
ATTENTION! PROPERTY DAMAGE!
► Use only accessories recommended by the manufacturer.
► The mains adapter may not be used for other purposes.
Never carry the wall bracket or the mains adapter by the
cable. Do not pull on the cable when you want to move
the appliance.
► Always grip the power plug to disconnect the appliance
from the power supply.
► Always be sure to keep the hand vacuum away from
heating elements, ovens or other heated appliances and
surfaces.
IB_365241_SAST18A1_LB8.indb 7 10.06.2021 10:37:23

■ 8 │ GB│IE SAST 18 A1
ATTENTION! PROPERTY DAMAGE!
► Make sure that the ventilation slits are never obstructed.
A blocked ventilation circuit can result in overheating and
damage to the appliance.
► The appliance is suitable for vacuuming small amounts of
water; however, its housing is not splashproof. Therefore,
do not immerse the appliance in water and do not expose
it to moisture!
► This product contains rechargeable batteries. Do not throw
the batteries into a fire and do not subject them to high
temperatures. There is a risk of an explosion.
► Do not use the hand vacuum cleaner without the HEPA
filter inserted.
► Do not use the mains adapter for a different product and
do not attempt to charge this appliance with a different
charger. Use only the mains adapter supplied with this
appliance.
► Never attempt to recharge non-rechargeable batteries.
► The batteries in this appliance cannot be replaced.
►
UN 34811
Tel. ____________
The product is equipped with or supplied with
a lithium-ion battery. Do not throw the batteries
into a fire and do not subject them to high
temperatures. There is a risk of explosion!
The mains adapter is for indoor use only.
IB_365241_SAST18A1_LB8.indb 8 10.06.2021 10:37:25

GB│IE │ 9 ■SAST 18 A1
Before first use
1) Remove all packaging materials from the appliance.
2) Check whether the filter holder u and the HEPA filter zare firmly installed
in the dirt container i. They may have worked loose during transport.
To insert the filter holder u and the HEPA filter z into the dirt container i,
proceed as follows:
–The filter holder u can only be fitted in the dirt container i in one
position. The side labelled “UP” must be facing upwards. Push the filter
holder uas far as possible into the dirt container i. Make sure that
the filter holder uis straight and that the rubber lip seals the dirt
container i.
–Insert the HEPA filter z into the filter holder u so that the catches on
the HEPA filter z fit into the corresponding recesses on the filter
holderu. The arrow on the HEPA filter z must be aligned with the
arrow on the filter holder u. Turn the HEPA filter z clockwise towards
the symbol.
3) Place the dirt container ion the motor unit r:
–First, place the contacts on the underside of the dirt container i onto
the contact pins on the underside of the motor unit r. This pushes the
two catches on the motor unit rinto the recesses on the dirt
containeri.
–Press the upper side of the dirt container i against the upper side of
the motor unit rso that the catch audibly engages. The dirt
containeriis now firmly seated on the motor unit r.
IB_365241_SAST18A1_LB8.indb 9 10.06.2021 10:37:25

■ 10 │ GB│IE SAST 18 A1
Information about the batteries
■ The appliance runs on rechargeable lithium-ion batteries. Before using the
appliance for the first time, the batteries must be charged. The charge
indicator lamp wflashes red during charging. As soon as the batteries are
fully charged, the charge indicator lamp wlights up green.
■ If the charge indicator lamp w flashes alternately green and red, the battery
is almost completely discharged and the appliance switches off after approx.
1 minute. This protects the appliance from deep discharge.
Installation of the wall bracket
DANGER! ELECTRIC SHOCK!
► Ensure that there are no power cables or water pipes in the wall at the
location where you intend to drill the holes for the wall bracket 7.
Drilling into a current-carrying electric cable can be potentially fatal!
1) Select a suitable installation location for the wall bracket 7:
It must be possible to remove the handheld vacuum cleaner easily and there
must be a mains power socket nearby. In addition, there should be no power
or water lines in the wall.
2) Drill two holes below each other at a distance of approx. 110 mm from each
other. The drill holes must be suitable for 6 mm wall plugs.
3) Push in the wall plugs and screw in the screws so that the heads protrude a
few millimetres.
4) Hang the wall bracket 7 with the drill holes over the two screws and ensure
that the screws slide into the slots. The wall bracket 7should lie flush
against the wall. You can adjust the distance to the wall and compensate for
any unevenness in the wall by screwing in or unscrewing the screws.
5) Ensure that the power cable is not trapped and that it lies properly in the
cut-out.
6) Push the two accessories holders 8into the respective catches on the left
and right of the wall bracket 7. You can place the nozzles in the
accessories holders 8.
7) Place the barrel plug 9of the power adapter 0into the wall bracket 7
from below. Secure the barrel plug 9by turning it.
8) Plug the mains adapter 0into a power socket.
IB_365241_SAST18A1_LB8.indb 10 10.06.2021 10:37:26

GB│IE │ 11 ■SAST 18 A1
Charging
NOTE
► Check to ensure that the On/Off switch qhas been pushed back (to the
position "OFF") before starting the charging process.
■ Hang the appliance into the wall bracket 7from above. The catches on the
wall bracket 7 should slide into the recesses on the motor unit r and the
barrel plug 9 into the socket on the lower end of the motor unit r. The
charge indicator lamp wflashes red and the charging process begins.
■ When charging is complete, which can take around 5 to 5.5 hours with fully
discharged batteries, the charge indicator lamp wlights up green. The
appliance automatically switches to trickle charging. Nevertheless, in order
to avoid possible damage to the batteries, do not leave the appliance
permanently connected to the mains adapter 0.
■ Recharge the batteries again if the appliance’s suction power becomes
appreciably weaker and the charge indicator lamp wflashes green.
NOTE
► If the charge indicator lamp w flashes alternately green and red, the
battery is almost completely discharged and the appliance switches off
after approx. 1 minute. This protects the appliance from deep discharge.
► The appliance can also be charged directly via the mains adapter 0. To
do this, remove the barrel plug 9from the wall holder 7with a slight
twist and insert it into the socket on the appliance.
► The appliance cannot be operated during charging.
IB_365241_SAST18A1_LB8.indb 11 10.06.2021 10:37:27

■ 12 │ GB│IE SAST 18 A1
Operation
ATTENTION!
► The suction opening must always be open and may not be blocked.
Blockages lead to overheating and damage to the motor.
► Use the wet-suction nozzle 5 only at level I (low/wet suction ).
NOTES
► Make certain that the HEPA filter zis inserted before using the appliance.
► When vacuuming liquid, do not exceed the MAX marking in the dirt
container i.
► If the motorised brush attachment 6 is blocked so that the brush can no
longer turn, the charge indicator lampw flashes red after approx. 15seconds
of the blockage, the working lightt goes out and the appliance stops
vacuuming. If this happens, remove the blockage as described in the section
“Cleaning the brush attachment”. Slide the On/Off switchq to the “OFF”
position. To restart the appliance, slide the On/Off switchqto position I
or II.
1) Remove the appliance from the wall bracket 7or, if you are not using the
wall bracket 7, remove the barrel plug 9from the socket.
2) If required, place the appropriate nozzle in the suction opening. See section
“Using accessories”.
3) To switch the appliance on, slide the On/Off switch qforwards into
position I (= low power/wet suction ) or position II (= high power).
The charge indicator lamp w lights up yellow at level I, green at level II.
The working light tlights up.
4) To switch the appliance off, place the On/Off switch qback to the “OFF”
position. All lamps go out.
NOTE
► After you have vacuumed up liquids, clean the dirt container i
immediately. Otherwise, bacteria or mould will build up inside! Ensure that
the HEPA filter zis completely dry before using the appliance again.
IB_365241_SAST18A1_LB8.indb 12 10.06.2021 10:37:27

GB│IE │ 13 ■SAST 18 A1
NOTE ON VACUUMING UP LIQUIDS.
► If you have vacuumed liquids, always carry the appliance with the wet-
suction nozzle 5pointing downwards:
► If you carry the appliance horizontally or with the wet-suction nozzle 5
pointing upwards, it is possible that liquid can leak out:
NOTE
► Place the appliance in the wall bracket 7and start the charging process
once the vacuum power has become noticeably weaker and the charge
indicator lamp wflashes green.
IB_365241_SAST18A1_LB8.indb 13 10.06.2021 10:37:27

■ 14 │ GB│IE SAST 18 A1
Using accessories
The crevice tool 1, the precision nozzle 3 and the wet-suction nozzle 5 can
simply be pushed into the suction opening on the appliance. The attachment must
sit securely.
The small brush attachment 4 and the universal nozzle 2 can only be used in
combination with the crevice tool 1. To do this, push them onto the crevice
tool1so that the catch on the crevice tool 1 clicks into the hole on the small
brush attachment 4 or the universal nozzle 2.
The motorised brush attachment 6can only be attached in a certain position.
The two contact pins on the brush attachment 6must be pushed into the contact
socket on the underside of the suction opening.
Selecting the right accessories:
Crevice tool
The crevice tool 1is ideal for cleaning narrow, hard-to-access areas such as
grooves in furniture or radiator ribs, etc.
Universal nozzle
The universal nozzle 2 is suitable for cleaning various surfaces. Can only be
used in combination with the crevice tool 1.
Precision nozzle
The precision nozzle 3is particularly well suited for cleaning in tight corners
and other hard-to-reach areas.
Small brush attachment
Use the small brush attachment 4to gently clean delicate surfaces or smaller
objects (such as computer keyboards, electrical appliances, etc.). Can only be
used in combination with the crevice tool 1.
Wet-suction nozzle
Use the wet-suction nozzle 5to vacuum up liquids. Use only on level I (low/
water suction ) When vacuuming liquid, do not exceed the MAX marking in
the dirt container i.
Motorised brush attachment
The motorised brush attachment 6is ideal for cleaning upholstery and carpets.
Can only be attached in a certain direction.
IB_365241_SAST18A1_LB8.indb 14 10.06.2021 10:37:28

GB│IE │ 15 ■SAST 18 A1
Cleaning
ATTENTION! PROPERTY DAMAGE!
► Do not use aggressive, chemical or abrasive cleaning agents. These could
damage the outer surfaces of the appliance.
Emptying the dirt container and cleaning the filter
NOTE
► To achieve the best results, empty the dirt container iand clean the HEPA
filter zregularly.
► If you need a new HEPA filter z, please contact our service department
(see section “Ordering spare parts”).
1) If you have not already done so, disconnect the appliance from the mains
adapter 0or lift it off the wall bracket 7.
2) To open the dirt container i, press the release button eand remove the
dirt container ifrom the appliance.
3) Remove the filter holder u together with the HEPA filter z from the dirt
container iby pulling both straight out of the dirt container i.
4) Empty the dirt container i.
5) Remove the HEPA filter z from the filter holder uby turning it
anticlockwise towards the symbol and pulling it out.
6) Tap out the HEPA filter zand the filter holder uover a rubbish bin. If
necessary, you can rinse out the filter holderuand the HEPA filter zwith
fresh water. Before replacing the parts ensure that they are completely dry.
Do not dry the HEPA filter zwith hot air.
7) Reinsert the filter holder uinto the dirt container i. Make sure that the
filter holder uis straight and that the rubber lip seals the dirt container i.
8) Insert the HEPA filter z into the filter holder u so that the catches on the
HEPA filter z fit into the corresponding recesses on the filter holder u.
The arrow on the HEPA filter z must be aligned with the arrow on the filter
holder u. Turn the HEPA filter zclockwise towards the symbol.
9) Replace the dirt container ion the motor unit r:
–First, place the contacts on the underside of the dirt container i onto
the contact pins on the underside of the motor unit r. This pushes the
two catches on the motor unit r into the recesses on the dirt
containeri.
–Press the upper side of the dirt container i against the upper side of
the motor unit rso that the catch audibly engages. The dirt
containeriis now firmly seated on the motor unit r.
IB_365241_SAST18A1_LB8.indb 15 10.06.2021 10:37:28

■ 16 │ GB│IE SAST 18 A1
Cleaning the brush attachment
To achieve the best results, the motorised brush attachment 6should be
checked regularly for blockages and any hairs, threads or dirt should be
removed.
To simplify cleaning, the brush on the brush attachment 6can be removed:
1) If you have not already done so, pull the brush attachment 6out of the
suction opening.
2) Push the release switch on the brush attachment 6in the direction of the
arrow (as far as the stop). The brush can now be removed and cleaned. The
release switch automatically springs back into place.
3) To replace the brush after cleaning, proceed as follows:
–Start by pushing one end of the brush onto the drive shaft on the
opposite side of the release switch. Note that only one side of the brush
fits onto the drive shaft.
–Push the release switch on the brush attachment 6in the direction of
the arrow (as far as the stop) and hold it there. Now push the other end
of the brush into the appropriate recess on the side of the release switch.
–Let go of the release switch to lock the brush in place. The brush should
now be straight and firmly attached to the brush attachment 6.
Cleaning the appliance
1) Clean the housing and the attachments with a slightly damp cloth.
For stubborn soiling use a mild detergent on the cloth.
2) Dry all parts thoroughly before using the appliance again or storing it.
Storage
Store the appliance in a dust-free and dry location.
IB_365241_SAST18A1_LB8.indb 16 10.06.2021 10:37:28

GB│IE │ 17 ■SAST 18 A1
Disposal
Disposal of the appliance
Never dispose of the appliance in your normal domestic waste.
This product is subject to the provisions of European Directive
2012/19/EU.
Dispose of the appliance via an approved disposal company or your municipal
waste facility. Please comply with all applicable regulations. Please contact your
local waste disposal facility if you are in any doubt.
Do not dispose of the mains adapter in your normal domestic
waste. This mains adapter is subject to the provisions of
European Directive 2012/19/EU WEEE (Waste Electrical and
Electronic Equipment).
Dispose of the mains adapter at an approved disposal centre or your community
waste facility. Please comply with all applicable regulations. Please contact your
local waste disposal facility if you are in any doubt.
Your local community or municipal authorities can provide information on how to
dispose of the worn-out product.
The product is recyclable, subject to extended producer responsibility and is
collected separately.
NOTE
► The appliance contains batteries that cannot be removed by the user.
To prevent risks, the removal or replacement of the batteries may only be
carried out by the manufacturer, manufacturer's customer service
department or a similarly qualified person. When disposing of the
appliance, indicate that the appliance contains batteries.
Disposal of packaging
The packaging materials have been selected for their environmental friendliness
and ease of disposal and are therefore recyclable.
Dispose of packaging materials that are no longer needed in accordance with
applicable local regulations.
Dispose of the packaging in an environmentally friendly manner.
Note the labelling on the packaging and separate the packaging material
components for disposal if necessary. The packaging material is labelled with
abbreviations (a) and numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard, 80–98: composites.
IB_365241_SAST18A1_LB8.indb 17 10.06.2021 10:37:31