Silvercrest SSRA1 User manual

SSRA1
Roboic Vacuum cleaner

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
RF radiationexposure statement
The Robotic Vacuum Cleaner complies with FCC RF radiation expo-
sure limits set forth for an uncontrolled environment.
Caution: To maintain the compliance with the FCC’s RF exposure
guideline, install the Robotic Vacuum Cleaner at least 7.9” (20 cm)
from ALL persons.
The transmitter of this device must not be co-located or operating in
conjunction with any other antenna or transmitter.
MODIFICATION: Any changes or modifications not expressly
approved by the grantee of this device could void the user’s
authority to operate the device.
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Consult the dealer or an experienced radio/TV technician for help.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
WARNING:

3US-EN
Description of signal words.............................................................................................Page 4
Customer service.......................................................................................................................Page 4
List of pictograms used........................................................................................................Page 4
Introduction...................................................................................................................................Page 5
Intended use........................................................................................................................................Page 5
Trademark notice ................................................................................................................................Page 5
Parts description..................................................................................................................................Page 5
Contents...............................................................................................................................................Page 7
Technical data.....................................................................................................................................Page 7
Important safety instructions.........................................................................................Page 7
Safety warnings for batteries..............................................................................................................Page 10
Initial use.........................................................................................................................................Page 12
Charging the product..........................................................................................................................Page 12
Attaching the side brushes..................................................................................................................Page 13
Turning the product on/off................................................................................................................Page 13
Use........................................................................................................................................................Page 13
Cleaning modes..................................................................................................................................Page 14
Virtual wall...........................................................................................................................................Page 16
Scheduling...........................................................................................................................................Page 16
Operation via app...................................................................................................................Page 17
Install and register...............................................................................................................................Page 17
Connecting the product to WiFi.........................................................................................................Page 18
Connecting the product to the app....................................................................................................Page 19
Disconnecting......................................................................................................................................Page 19
Cleaning via app ................................................................................................................................Page 20
Scheduling...........................................................................................................................................Page 22
Cleaning records.................................................................................................................................Page 23
Product maintenance ..........................................................................................................................Page 23
Settings ................................................................................................................................................Page 24
Operation via Alexa..............................................................................................................Page 26
Cleaning and storage ...........................................................................................................Page 28
Troubleshooting ........................................................................................................................Page 28
Disposal............................................................................................................................................Page 31
Three year limited warranty..........................................................................................Page 31
309029_1901__silv_Saugroboter SSRA1_content_US.indd 3 11.09.19 08:26

4 US-EN
DESCRIPTION OF SIGNAL WORDS
WARNING indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury.
NOTICE indicates information considered important, but not hazard
related (e.g. messages related to property damage).
CUSTOMER SERVICE
Call customer service at
1 [phone]
Visit the Website Customer Service
Platform at www.lidl.com/contact-us
Visit a LIDL store for further assistance.
IAN 309029_1901 Please have your
IAN number ready.
List of pictograms used
Follow the warnings and safety notes! Short-circuit proof safety
transformer
Please read the instructions! SMPS (Switch mode power
supply unit)
This product is only suitable for indoor
use in dry, enclosed spaces.
Note polarity/battery pack data
Direct current Power supply polarity
Alternating current
b
a
Dispose of the packaging and
product in an environmentally-
friendly manner!
Protection class III 36 month warranty
Never leave children unattended with
the packaging material or the product.
Tested according Federal
Communications Commission
309029_1901__silv_Saugroboter SSRA1_content_US.indd 4 11.09.19 08:26

5US-EN
Robot vacuum cleaner SSRA1
Introduction
Congratulations on your purchase. You have selected
a quality product. The instructions for use are a part
of the product. They contain important information
about the safety, use and disposal of the product.
Before using the product, please learn about all the
safety information and usage instructions. Only use
the product as described and for the specified ap-
plications. If you lend the product to someone else,
please also give all the instructions.
Intended use
This product is suitable for vacuuming up loose, dry
dirt, e.g. dust, lint or crumbs on smooth flooring and
low pile carpets. Only use the product indoors. This
product is only intended for private, non-commercial
use. Only use the product for the intended purpose.
Any use other than previously mentioned or product
modification is prohibited and can result in injuries
and/or damage. The manufacturer assumes no lia-
bility for damage arising from improper use.
Trademark notice
· The trademark and the brand name SilverCrest
are the property of their respective owners.
· All other names and products may be trademarks
or registered trademarks of their respective own ers.
Parts description
Robot vacuum cleaner
1Display
2Charging dock
3Charging contacts
4Power cable
5Virtual wall
6HEPA filter
7Replacement side brushes
8Cleaning brush
9Power switch
10 Charging socket
11 “Dust bin“ button
12 “Start /Pause“ button
13 “Auto mode“ button
14 “Set schedule“ button
15 “Spot mode“/Time down button
16 “Return mode“/ Time up button
9
10
11
12
13
14 16
78
2
3
1
15
5
4
6
309029_1901__silv_Saugroboter SSRA1_content_US.indd 5 11.09.19 08:26

6 US-EN
17 Dust bin
18 Side wheel
19 Combo floor brush
20 Side brushes
21 Cliff sensor
22 Front wheel
23 Anti-collision sensor
17
18
19
20
212223
18
24 Dust bin cover
25 Main filter
26 Foam filter
25
24
26
Remote control
27 Directional buttons
28 “Start /Pause“ button
29 “Spot mode“ button
30 “Corner mode“ button
31 “Find robot vacuum cleaner“ button
32 “Max mode“ button
33 “Return mode“ button
34 “Auto mode“ button
30
3133
34
29
27
28
32
309029_1901__silv_Saugroboter SSRA1_content_US.indd 6 11.09.19 08:26

7US-EN
Contents
Verify that the contents are complete and that the
product is in perfect condition immediately after
unpacking.
1 Robot vacuum cleaner
1 Dust bin
1 Charging dock
1 Virtual wall
1 Main combo floor
brush with bristles
and flexible beaters
2 HEPA filters
4 Side brushes
1 Remote control
1 Power adapter
1 Cleaning brush
2 AA batteries
2 AAA batteries
1 Instructions for use
Technical data
Robot vacuum cleaner
Model: Silvercrest SSRA1
Operating voltage: 14.8V (direct current)
Rated power: 22W
Rechargeable battery: Lithium-ion rechargeable
battery (4 cells), 2.6Ah,
14.8V, 38.5Wh
Run time: max. 120 minutes (varies
by mode and flooring)
Charging time: 5–6 hours
Charging dock
Rated output voltage: 19V (direct current)
Rated output current: 0.6A
Remote control
Model: SSRA1
Rated input voltage: 3V (direct current)
Battery: 2 x 1.5V AAA (included)
Power supply
Input: 100–240V∼ 0.5A
max. 50/60 Hz
Output:
19V (direct current) 0.6A
Virtual wall
Battery: 2 x 1.5V AA (included)
App
System requirements: iOS Version 9.0 and up,
Android™ Version 4.4 and up
IMPORTANT
SAFETY IN-
STRUCTIONS
KEEP ALL SAFETY NOTES AND
INSTRUCTIONS FOR USE FOR
FUTURE REFERENCE!
Failure to
observe the following warn-
ings may result in death or
serious injuries.
D ANGER TO LIFE AN D
RISK OF ACCIDENTS
FOR INFANTS AND CHIL-
DREN! Never leave children
unsupervised with the packaging
material. Suffocation hazard. K eep
children away from the product.
DANGER TO LIFE! Batteries are
not intended for children. Do not
leave batteries lying around. Chil-
dren or pets could swallow them.
If swallowed, seek immediate
medical attention.
This product is not intended for
use by persons (including childr en)
with reduced physical, sensory
or mental capabilities or lacking
experience and knowledge unless
supervised or instructed in safe
product use by a person respon-
sible for their safety. Children
309029_1901__silv_Saugroboter SSRA1_content_US.indd 7 11.09.19 08:26

8 US-EN
should be supervised to ensure
they do not play with the product.
Verify the line voltage matches
that specified on the charging
dock 2.
Never use the charging dock 2
if damaged.
Handle the power cable 4with
care to avoid damage. Do not
use the power cable 4to move
or pull the product or charging
dock 2. Do not allow the prod-
uct to run over the power cable
4and keep it away from heat
sources.
I f the power cable
4
is damag ed,
it must be replaced by a quali-
fied service technician to avoid
dangers.
Do not use the product in rooms
with children.
Do not use the product near
open fire.
Do not allow the product to
vacuum up flammable materials,
for example fuel or printer or
copier toner.
Do not allow the product to vac-
uum up burning items, for exam-
ple cigarettes, matches, ashes and
other objects which could cause
a fire.
Check the charging dock, power
cable or power adapter for dam-
age before every use.
To reduce the risk of electric
shock – Do not use outdoors
or on wet surfaces.
Use only manufacturer’s recom-
mended attachments.
Do not unplug by pulling on cord.
To unplug, grasp the plug, not the
cord.
Do not handle plug or appliance
with wet hands.
Changes or modifications to this
product not expressly approved
by the party responsible for
compliance could void the user‘s
authority to operate the product.
Note: This product has been
tested and complies with the lim-
its for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in a
r esidential installation. This produ ct
generates, uses and can radiate
r adio frequency energy and, if n ot
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications.
However, there is no guarantee
that interference will not occur
309029_1901__silv_Saugroboter SSRA1_content_US.indd 8 11.09.19 08:26

9US-EN
in a particular installation. If this
product causes harmful interfer-
ence to radio or television recep-
tion, which can be determined
by turning the product off and on,
the user is encouraged to try and
correct the interference by one or
more of the following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation betw een
the equipment and receiver.
• Connect the product into an
outlet on a circuit different
from that to which the receiver
is connected.
• Consult the dealer or an expe-
rienced radio/TV technician
for help.
This product complies with part
15 of the FCC Rules. Operation
is subject to the following two
conditions:
(1) This product may not cause
harmful interference, and
(2) this product must accept any
interference received, including
interference that may cause un-
desired operation.
Failure to
observe the following warn-
ings can result in injuries or
property damage.
Only use the original recharge-
able battery and charging dock
2supplied by the manufacturer.
Never use primary batteries.
For more information about the
battery, please see chapter
“Technical data“.
Do not use the product if it can‘t
work properly due to
- falls,
- damages,
- ingress water,
- outdoor use.
Have the product repaired by
the manufacturer or its customer
service department.
Keep hair, clothing and fingers
away from the openings or op-
erating parts of the product.
Regularly clean the cliff sensors.
If the floor sensors are dirty, the
product may fall down stairs or
landings.
When using the product, inform
any others in the room so nobody
steps on or trips over the product.
Discontinue using the product if
the plastic parts are cracked or
deformed. Always replace dam-
aged parts with genuine spare
parts.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 9 11.09.19 08:26

10 US-EN
Do not use the product on wet
or damp floors.
Do not use the product in tempe ra-
tures over +104°F (+40°C) or
below +50°F (+10°C).
Remove any obstacles prior to
use, for example power cables,
toys and other objects.
Tuck rug edges under the rug.
Keep curtains and tablecloths
off the floor.
Try to position furniture properly.
Test the product in areas with
stairs. This allows you to verify
the product detects the edge of
the drop off.
Do not stand in the way of the
robot vacuum cleaner. Otherwise
the robot vacuum cleaner will be
unable to clean these areas.
Do not allow the product to vac-
uum up items which could clog
the product, for example stones,
paper waste, etc.
Do not use the product if the suc-
tion opening is blocked. Remove
dust, hair, cotton balls, etc., to
allow air to flow freely in the
suction opening.
Verify the dust bin 17 and the
filters 6, 25 , 26 are installed
correctly before use.
Check the area being cleaned
before every use and observe
the safety notes and information
about preparing the room.
Regularly check and clean the
filters and the dust bin to extend
the life of your product.
Never use the product without
filters, as this will damage the
motor and shorten the life of the
product.
Always turn the product off
before transporting it.
Fully charge the product at least
once a month to prevent deep
discharge, which will damage
the battery.
Do not cover or tape off the cliff
s ensors on the product. Otherw ise
the product will be unable to
navigate.
Only use the product with the re-
mote control when it is within si ght.
Safety warnings
for batteries
When used correctly, cells and
batteries provide a safe and
dependable source of portable
power. However, if they are mis-
used or abused, this may result in
leakage, burns, fire, or explosion.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 10 11.09.19 08:26

11US-EN
Store batteries in a dry place at
room temperature. Batteries are
sensitive to high and low tempera-
tures. Such thermal exposure may
lead to leakage, fire, or explosion.
Keep cells and batteries out of
reach of children, especially small
batteries. Ingestion may lead to
choking or acute and serious
personal injury.
Keep cells or batteries clean and
dry both during use and storage.
Wipe metal terminals with a soft,
dry cloth if they become dirty.
Immediately seek medical atten-
tion if a cell or battery has been
swallowed. Also, contact your
local poison control center.
In the event that the electrolyte
comes into contact with the skin or
eyes, immediately flush with fresh
water for at least 15 minutes and
seek medical attention.
Store unused batteries in their
o riginal packaging or in safe pl ace
and away from metal objects that
may short-circuit them.
Exercise care in handling batteries
in order to prevent shorting with
conducting materials, such as
rings, coins, bracelets, and keys.
The battery or the conductor can
overheat and cause burns, leak-
age, fire, or explosion.
Clean the battery contacts and
also those of the product prior
to battery installation. Keep the
contacts clean.
Remove batteries from the product
that will not be used for an ex-
tended period of time (months
or longer).
R emove discharged batteries fro m
product promptly to avoid possib le
damage from leakage.
Choose the proper battery for
the intended application.
Always take care to correctly in-
sert batteries observing (+) and
(-) polarity marks on the battery
and the product for which it is in-
tended. Proper polarity must be
observed to avoid damage to
either product or batteries.
Always replace the whole set of
batteries at one time, taking care
not to mix old and new ones, or
batteries of different types, capac-
ities, or manufacturers.
Never heat batteries in order to
revive them.
Never charge a battery unless t he
battery label specifically states t he
battery is rechargeable. Charging
a non-rechargeable battery, may
r esult in leakage, fire, or explosi on.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 11 11.09.19 08:26

12 US-EN
Use only the power cord supplied
with the product. The use of other
cords may result in the batteries
inside the product being charged.
Do not open or mutilate a battery
or cell. Electrolyte from the cell is
corrosive and can cause damage
to the eyes or skin. The cell conten ts
can also be hazardous if ingested.
Do not drop or subject the cell
or battery to strong mechanical
shock.
Batteries should not be disassem-
bled, crushed, punctured, or oth-
erwise mutilated. Such abuses
may result in leakage, fire, or
explosion.
Do not dispose of the battery
in a fire. Failure to observe this
precaution may result in an ex-
plosion.
Dispose of batteries properly and
in accordance with government
regulations.
Only for robot vacuum
cleaner
Store products with integrated
batteries or cells in a dry place
at room temperature. Batteries
are sensitive to high and low
temperatures. Such thermal ex-
posure may lead to leakage, fire,
or explosion.
Do not open or mutilate products
with integrated batteries or cells.
Electrolyte from the cell is corro-
sive and can cause damage to
the eyes or skin. The cell contents
can also be hazardous if ingested.
Do not drop or subject products
with integrated batteries or cells
to strong mechanical shock.
Do not dispose of products with
integrated batteries or cells in a
fire. Failure to observe this precau-
tion may result in an explosion.
Dispose of products with integr ated
batteries or cells properly and
in accordance with government
regulations.
SAVE THESE
INSTRUCTIONS
Initial use
Charging the product
Fully charge the product before using it for the
first time.
The charging time is 5 to 6 hours. The charging
process is also indicated in the display 1.
Set up the charging dock 2and connect the
power cable 4.
Place the charging dock 2flush against a wall.
Note: keep 3.28ft (1m) from the left/right
side and 6.56ft (2m) from the front clear.
Turn on the power switch 9on the product
(position “–“) before charging.
Place the product on the charging dock 2and
line it up with the charging contacts 3.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 12 11.09.19 08:26

13US-EN
You can alternatively plug the power cable 4
directly into the charging socket 10 on the
product.
Note: the product sometimes corrects the
position on the charging dock.
“Start/ Pause“ button 12
blinking orange: charging
green: fully charged
off: Sleep mode
Note: the area around the charging dock 2must
n
ot have mirrors or other highly reflective objects wi thin
5.9in (15cm) of the floor. If necessary, cover these.
CAUTION! Avoid exposing the charging
dock 2to direct sunlight.
CAUTION! Change the position of the charging
dock 2as little as possible.
Attaching the side brushes
Install the side brushes 20 according to the slot
color, pressing the brushes onto the color pins.
Verify the side brushes 20 are secure.
Turning the product on/off
Press the power switch 9on the side of the
product. “–“ means on, “O“ means off. If the
„Start /Pause“ button 12 lights up green, the
product is on.
Note: do not turn the product off after it has finished
cleaning. Keep the product in the charging dock 2
so it will be ready for the next vacuuming.
Note: pressing the power switch 9will erase the
date, time and schedule.
Use
Due to the complexity of domestic environments,
the product may skip some areas when cleaning.
For better cleaning results we recommend using the
product daily.
Remove obstacles before use, for example
power cables, toys and other objects.
Tuck rug edges under the rug. Keep curtains
and tablecloths off the floor.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 13 11.09.19 08:26

14 US-EN
Try to position furniture properly.
Test the product in areas with stairs. This allows
you to verify the product detects the edge of
the drop off.
Do not stand in the way of the robot vacuum
cleaner. Otherwise the robot vacuum cleaner
will be unable to clean these areas.
Find robot vacuum cleaner
A beep will sound after pushing the “Find robot
v
acuum cleaner” button
31
on the remote contro l.
You can then locate your robot vacuum cleaner.
Cleaning
Press the “Start / Pause“ button on the robot
vacuum cleaner 12 or the remote control 28 .
The “Start /Pause“ button on the robot vacuum
cleaner 12 will light up.
If the “Start/Pause“ button 12 flashes, the robot
vacuum cleaner will start in “Classic mode”.
Pausing
Press the “Start / Pause“ button on the robot
vacuum cleaner 12 or the remote control 28
during cleaning to pause the cleaning mode.
While the robot vacuum cleaner is paused, you
can push the directional buttons
27
on the rem ote
control to have it move left/ right/forward/
backward.
With the robot vacuum cleaner paused you can
press the directional buttons 27 on the remote
control to have it move left/ right.
Note: if paused more than 10 minutes, the
robot vacuum cleaner will enter Sleep mode
and the “Start/ Pause“ button 12 will go off.
Press the “Start / Pause“ button on the robot
vacuum cleaner 12 or the remote control 28
again to exit Sleep mode. Then push the button
with the desired mode to resume cleaning.
Note: when the product resumes after being pa used,
it recalculates the area and may clean areas it has
already cleaned.
Note: if you have two robot vacuum cleaners, you
can control both with one remote.
Cleaning modes
The product has different cleaning modes for better
results. You can select the modes by pressing the
button on the control panel, the remote control or
in the app.
To start the following modes, ensure the product
is “awake“. If it has entered Sleep mode, press
the “Start/ Pause“ button on the robot vacuum
cleaner 12 or on the remote control 28 to exit
Sleep mode.
Classic mode
In this mode the product moves in all directions. This
mode is recommended for vacuuming carpets.
Press the “Start / Pause“ button on the robot
vacuum cleaner 12 or on the remote control 28
to start “Classic mode“.
Auto mode
309029_1901__silv_Saugroboter SSRA1_content_US.indd 14 11.09.19 08:26

15US-EN
In this mode the product uses parallel, overlapping
lanes. It will first vacuum along the edges of the room
for guidance and to measure the room.
Press the “Auto mode“ button on the robot
vacuum cleaner 13 or on the remote control 34
to start this mode.
Spot mode
This mode is suitable for very dirty or very dusty
areas. In Spot-cleaning mode the product will focus
on one area to clean.
Press the “Spot mode“ button on the robot
vacuum cleaner 15 or on the remote control 29
to start this mode.
Note: the product will vacuum a 19.7in (50 cm)
radius.
Max mode
This mode is suitable if the floor is very dirty or dusty.
In Classic, Auto or Corner mode, press the
“Max mode“ button on the remote control 32 .
Suction will increase for a deeper cleaning.
Press the “Max mode“ button 32 again to
switch to the current mode with normal suction.
Corner mode
This mode is suitable for cleaning corners and edges
of a room. In “Corner mode“ the product follows
a barrier (for example a wall). In this mode the
product will clean for 20 minutes and return to the
charging dock.
Press the “Corner mode“ button on the remote
control 30 to start this mode.
Return mode
Use this mode to return the product to the charging
dock 2.
Note: the robot vacuum cleaner automatically re-
turns to the charging dock when the battery is low.
Press the “Return mode“ button on the robot
vacuum cleaner 16 or on the remote control 33
to return the robot vacuum cleaner to the c harging
dock 2.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 15 11.09.19 08:26

16 US-EN
Virtual wall
The virtual wall 5divides your home into separate
areas to improve the cleaning efficiency of the produc t.
For better performance, place the virtual wall 5
at a door or in front of a passage less than 9.84ft
(3m) wide.
The virtual wall 5creates an invisible barrier
which blocks the product across a length of up
to 9.84ft (3 m).
Before using the virtual wall 5you need to in-
stall 2 AA batteries (included). Open the battery
cover and insert the batteries. Please note the
indicated polarity.
Slide the switch on the virtual wall 5to “ON“
to turn it on.
The virtual wall 5must be positioned so the
laser is parallel to the floor and battery com-
partment on the bottom.
Slide the switch on the virtual wall 5to “OFF“
when it is not in use.
Position your robot vacuum cleaner in the
“cleaning area“ as shown.
Area : outside work area
Area : work area
Scheduling
For easy cleaning you can program the time and
a schedule for future cleaning on the robot vacuum
cleaner or in the app.
Setting the time
H old the “Set schedule“ button
14
for 2 seco nds
with the robot vacuum cleaner “awake“. The
robot vacuum cleaner will beep, the display 1
will flash and the robot vacuum cleaner will enter
Set Clock mode.
Press the “Time down/ up“ buttons 15 , 16 to
set the current time. Use the “Set schedule“ 14
button to switch between minute, hour and day.
Press the “Auto mode“ button 13 or Time
down/ up 15 , 16 to switch between 12 and
24 hour mode.
After setting the time, press the “Start/Pause“
button 12 to save.
Note: if no buttons are pressed within 15 sec-
onds, the robot vacuum cleaner will exit Set
Time mode and the setting will be lost.
Programming the schedule
Press the “Set schedule“ button 14 with the ro-
bot vacuum cleaner “awake“. The robot vacuum
cleaner will beep and “Symbol“ and “MON“
will flash. The robot vacuum cleaner will enter
“Set schedule mode“.
Press the “Time down/ up“ buttons 15 , 16 to
set the desired cleaning time. Use the “Set
309029_1901__silv_Saugroboter SSRA1_content_US.indd 16 11.09.19 08:26

17US-EN
schedule“ 14 button to switch between minute,
hour and day.
After setting the schedule, press the “Start/
Pause“ button 12 to save. The robot vacuum
cleaner will start cleaning according to the
schedule.
Deleting the schedule
Press the “Set schedule“ button 14 with the ro-
bot vacuum cleaner “awake“. The robot vacuum
cleaner will beep and “Symbol“ and “MON“
will flash. The robot vacuum cleaner will enter
“Set schedule mode“.
Press the “Auto mode“ button 13 to delete the
stored schedule; the display 1will read “--:--“.
Press the “Auto mode“ button 13 again to re-
activate the schedule. The display 1will show
the last schedule programmed. After setting the
schedule, press the “Start / Pause“ button 12
to save.
Operation via app
The product can be operated remotely via app.
Install and register
The “SILVERCREST SSRA1 AX US“ app is available
for free from the Apple App Store and Google Play.
Install the app “SILVERCREST SSRA1 AX US“
on your smartphone.
Open the app and click “Profile“.
Click “Login/Sign up“.
In the Login menu, click “Sign up“.
Enter your e-mail address and agree to the
User Agreement to register. Click “Next Step“
to continue.
Click “Obtain verification code“ and retrieve
the confirmation code from your e-mail inbox.
Enter the verification code and choose a pass-
word. Click “Sign up“ to log in.
After registering, the app will automatically
switch to the “Robot“ menu.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 17 11.09.19 08:26

18 US-EN
If you are not logged into your account, click
“Add robot“ or “+“. The app swill then auto-
matically switch to the Login menu.
Enter your e-mail address and password and
click “Login“.
After successfully logging in, the app will auto-
matically switch to the “Robot“ menu.
Connecting the product to WiFi
Choose a 2.4 GHz WiFi network (the robot
vacuum cleaner will not connect to 5 GHz
WiFi networks) with a strong signal in your
smartphone settings to connect your product.
Verify your WiFi network allows devices.
Set the power switch 9on the robot vacuum
cleaner to “–“.
Hold the “Spot mode/ Time down”
15
button on
t he robot vacuum cleaner for 4 seconds until y ou
hear a beep.
In the “Robot“ menu, click “Add robot“ or “+“
to add the robot vacuum cleaner.
Select robot model “SSRA1“.
Please note the assistance in the app and click
“Continue“.
In the “Network configuration“ menu, enter
your WiFi password, then click “Continue“.
Click “Settings“, navigate to “Settings/WiFi“
on your smartphone and select the network
“Robot-XXXX“.
Return to the app and verify a robot network
(Robot-XXXX) is selected under “Robot hotspot“.
Click “Connect“ to connect to the WiFi network.
The robot vacuum cleaner should now connect.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 18 11.09.19 08:26

19US-EN
Connecting the product
to the app
When the robot vacuum cleaner beeps and the
WiFi indicator stays on, the robot vacuum cleaner
successfully connected to the WiFi network.
The first user connecting to the product becomes
the administrator for the product. Only the adminis-
trator is able to share the product with other users.
Other users can only disconnect from the product.
After successfully connecting, the app will
open a pop-up window where you can assign
a name to your robot. Then click “Confirm“.
The app will then automatically switch to the
“Robot“ menu.
Note: if the robot vacuum cleaner is turned off
and you want to reconnect it to WiFi, turn on the
robot vacuum cleaner and it will automatically
reconnect to the same WiFi network.
Note: administrator rights are linked to the
e-mail address.
Disconnecting
Disconnecting through the administrator
In the “Robot“ menu, select your robot and
swipe left.
Click “Disconnect“.
Disconnecting through the robot vacuum
cleaner
Turn on the robot vacuum cleaner and wait
30 seconds to determine if the robot vacuum
cleaner connects to the WiFi network. If the ro-
bot vacuum cleaner is connected to the network,
it will beep to remind you and the WiFi indicator
on the robot vacuum cleaner will switch from
flashing to steady.
While connected to WiFi, hold the “Spot mode/
Time down” button 15 on the robot vacuum
cleaner for 4 seconds until you hear a beep.
The robot vacuum cleaner has been disconne cted
from all users. The consumer can then restart the
robot vacuum cleaner and connect to it.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 19 11.09.19 08:26

20 US-EN
Cleaning via app
Auto mode
Select your vacuum from the “Robot“ menu.
Click to switch to the “Settings“ menu.
Select “Auto mode“ so the robot will enter this
mode the next time it is started via the app.
Classic mode
Select your vacuum from the “Robot“ menu.
Click to switch to the “Settings“ menu.
Select “Classic mode“ for the robot to enter
this mode the next time it is started via the app.
309029_1901__silv_Saugroboter SSRA1_content_US.indd 20 11.09.19 08:26