Uplus Lighting MH12X40 PIXEL BAR User manual

User manual
MH 12X40 PIXEL BAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………6-8
Trouble Shooting…………………………………………………………………………………9
Fixture Cleaning………………………………………………………… ………………………9
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Input Voltage: 100-240V,50/60Hz
Light Source: 12*40W RGBW 4in1 LED
Light source life: 50000 hours
Power consumption: 600W
Color temperature: 2800K-8500K
Zoom angle: 5-45°
Tilt: 270°Tilt resolution: 16 bits
Sectional independent control of focusing system
Dimmer:0-100%(16bit)
Strobe:1-20Hz
DMX Channels: 20/57CH
Operate mode: Master/Slave,Auto,Sound active,DMX512,RDM
NW:15KG
Dimension:1020x110x310mm
Features:
The appearance is simple, the structure is compact, the shell is made of aluminum alloy and
engineering plastics, the volume is small, the weight is light, and the side wall has a positioning
splicing shaft design to keep the lamps vertically spliced in a straight line. The operation is simple
and convenient. After splicing, the distance between the lamp beads is equal, The overall lighting
effect is continuous, the focusing system can be individually controlled in sections, a single light
source can be controlled, a variety of color macro effects, 16bit dimming, efficient heat dissipation
system, full temperature monitoring, automatic over-temperature protection, only fan speed
adjustment, Real-time display of temperature, one-key reverse display of settings

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
Main menu
Secondary menu
hree-level menu/parameters
parameters
Dmx Address
001 - 512
Fixture
Ch Mode
STD/EXT
Run Mode
DMX/Host/Sound
Tilt Inv
Close/Open
Manual
Tilt
0 - 255
Tilt Fine
0 - 255
.
0 - 255
.
0 - 255
.
0 - 255
Information
Time
Current Time
xxxh
Total Time
xxxh
Power Count
xxx
Sensor
Tilt
TRUE/FALSE
Zoom1
TRUE/FALSE
Zoom2
TRUE/FALSE
Temp
TRUE/FALSE
Temperature
Head Temp
xxx C
Software Version
Panel
Vx.xxx
Dimmer
Vx.xxx
Factory
Password
0 - 255
Tilt
0 - 255
Zoom1
0 - 255
Zoom2
0 - 255
Red
0 - 255
Green
0 - 255

6
Blue
0 - 255
White
0 - 255
Fixture Reset
Reset
Run/OFF
Factory
Run/OFF
Display
Language
EN/CH
Display Flip
Normal/Reverse
Display Mode
Show/60s
4.DMX Channels
20 CH Mode
20CH
Standard mode
Channel name
Channel value
Channel content
1
Tilt
0 - 255
Vertical rotation
2
Tilt Fine
0 - 255
Vertical fine-tuning
3
Tilt-Speed
0 - 255
Vertical motor speed
4
Zoom All
0 - 255
Enlarge the whole
5
Zoom1
0 - 255
Zoom in 1
6
Zoom2
0 - 255
Zoom in 2
7
Dimmer
0 - 255
Dimming 8bit
8
Dim Fine
0 - 255
Dimming 16bit
9
Strobe
0 - 3
shut down
4 - 103
Regular stroboscopic, the speed changes
from slow to faster
104 - 107
turn on
108 - 207
Pulse stroboscopic, the speed changes
from slow to fast
208 - 212
turn on
213 - 225
Random slow strobe
226 - 238
Random medium speed strobe
239 - 251
Random fast strobe
252 - 255
turn on
10
Red
0 - 255
red
11
Green
0 - 255
green
12
Blue
0 - 255
blue
13
White
0 - 255
white

7
14
Inner Effect
Built-in effect selection
0 - 10
no effect
11 - 13
Static effect 1
14 - 16
Static effect 2
… …
… …
67 - 70
Static effect 20
71 - 72
Dynamic effect 1
73 - 75
Dynamic effects 2
… …
……
188 - 190
Dynamic effects 40
191 - 193
Dynamic color effect 1
… …
… …
218 - 220
Dynamic color effect 10
221 - 255
Dynamic color effect 11
15
Effect Speed
0 - 255
Dynamic effect speed (from slow to fast)
16
LED Mirror
0 - 255
LED lamp beads left and right mirroring
17
For Color
0 - 255
Foreground color macro
18
Back Color
0 - 255
Background color macro
19
Back Color Dimmer
0 - 255
Background dimming
20
Function
Features
57 CH Mode
57CH
Extended mode
Channel name
Channel value
Channel content
1
Tilt
0 - 255
Vertical rotation
2
Tilt Fine
0 - 255
Vertical fine-tuning
3
Tilt-Speed
0 - 255
Vertical motor speed
4
Zoom1
0 - 255
Zoom in 1
5
Zoom2
0 - 255
Zoom in 2
6
Dimmer
0 - 255
Dimming 8bit
7
Dim Fine
0 - 255
Dimming 16bit
8
Strobe
0 - 3
shut down
4 - 103
Regular stroboscopic, the speed changes
from slow to faster
104 - 107
turn on
108 - 207
Pulse stroboscopic, the speed changes
from slow to fast

8
208 - 212
turn on
213 - 225
Random slow strobe
226 - 238
Random medium speed strobe
239 - 251
Random fast strobe
252 - 255
turn on
9
LED1 Red
0 - 255
LED1 red
10
LED1 Green
0 - 255
LED1 green
11
LED1 Blue
0 - 255
LED1 blue
12
LED1 White
0 - 255
LED1 white
13
LED2 Red
0 - 255
LED2 red
14
LED2 Green
0 - 255
LED2 green
15
LED2 Blue
0 - 255
LED2 blue
16
LED2 White
0 - 255
LED2 white
… …
… …
… …
……
53
LED12 Red
0 - 255
LED12 red
54
LED12 Green
0 - 255
LED12 green
55
LED12 Blue
0 - 255
LED12 blue
56
LED12 White
0 - 255
LED12 white
57
Function
Features
Fixture Reset
101-120
Fixture reset
Reserve
Reserve

9
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.