Sime Planet Super 4 F.S. User manual

Planet
Super 4 F.S.
User Instructions
UK
ENSURE THAT THESE INSTRUCTIONS ARE LEFT
FOR THE USER AFTER COMPLETION OF THE
BENCHMARK SECTION
Please read the Important Notice within
this guide regarding your boiler warranty
199838

All descriptions and illustrations provided in this manual have been carefully prepared but we reserve the right to make changes
and improvements in our products that may affect the accuracy of the information contained in this manual.
IMPORTANT NOTICE
For the first year all of our appliances are protected by our manufacturer’s guarantee which covers both parts and
labour.
As you would expect from Sime Ltd, it is our aim to provide our valued customers with the best in after sales and
service.
To take advantage of any extended warranty offered, all you have to do is to adhere to these 3 simple conditions:
• The installation must be carried out to Manufacturers/Benchmark Standards by a Gas Safe Registered
Engineer, and recorded in the installation manual.
• The appliance must be registered with both Sime Ltd and Gas Safe within 30 days of installation.
• The appliance must be serviced annually, by either Sime Ltd or a Gas Safe registered engineer- ensuring that the
Benchmark service record in the installation manual is completed.
Failure to comply with the above will result in only the 12 month warranty being offered.
In the absence of any proof of purchase, the 12 month warranty period will commence from the date of manufacture
of the boiler as shown on the appliance data plate.

The Benchmark Scheme
Sime Ltd is a licensed member of the Benchmark Scheme which aims to improve the standards of installation and
commissioning of domestic heating and hot water systems in the UK and to encourage regular servicing to optimi-
se safety, efficiency and performance.
Benchmark is managed and promoted by the Heating and Hotwater Industry Council.
For more information visit www.centralheating.co.uk
Please ensure that the installer has fully completed the Benchmark Checklist on the inside back pages of the
installation instructions supplied with the product and that you have signed it to say that you have received a full
and clear explanation of its operation.
The installer is legally required to complete a commissioning checklist as a means of complyng with the appropria-
te Building Regulations (England and Wales).
All installations must be notified to Local Area Building Control either directly or through a Competent Persons
Scheme.
A Building Regulations Compliance Certificate will then be issued to the customer who should, on receipt, write the
Notification Number on the Benchmark Checklist.
This product should be serviced regularly to optimise its safety, efficiency and performance.
The service engineer should complete the relevant Service Record on the Benchmark Checklist after each service.
The Benchmark Checklist may be required in the event of any warranty work and as supporting documentation
relating to home improvements in the optional documents section of the Home Information Pack.

5
BOILER IGNITION (fig. 1)
Open the gas cock, lower the cover of the
control and activate the boiler by turning
the selector knob to the summer ( ).
position. When the green led ( ) lights up,
electricity is present in the boiler.
– With the selector knob on the summer
( ) position, the boiler works to take
the temperature of the hot water to the
fixed value.
– With the selector knob on the winter
position ( ) the boiler, once it has rea-
ched the temperature set on the heating
potentiometer, will begin to modulate
automatically in order to supply the
system with the effective power reque-
sted. The boiler will stop functioning if
the room stat or “Logica Remote Con-
trol” intercede.
TEMPERATURES ADJUSTMENT (fig. 2)
The panel of the red leds is graduated from
40÷80 °C and shows the temperature in
the D.H.W. tank when the two service leds
( ) are off; it shows the temperature
of the primary circuit when one of the two
leds is lit up.
– Regulation of the D.H.W. temperature is
carried out by acting on the hot-water
service knob ( ). The set temperature
is displayed on the scale of the red leds
from 40 ÷80 °C.
– Regulation of the C.H. temperature is
carried out by acting on the heating knob
( ). The set temperature is shown on
the scale of the red leds from 40÷80 °C.
To guarantee an always optimal output
from the generator it is advised not to
go below a minimum operating tempera-
ture of 50 °C.
TURNING OFF BOILER (fig. 1)
To turn the boiler off place the selector
knob on the OFF position.
IF THE BOILER IS NOT GOING TO BE USED
FOR A LENGTHY PERIOD IT IS ADVISED TO
TURN OFF THE ELECTRICITY SUPPLY,
CLOSE THE GAS COCK, AND IF LOW TEM-
PERATURES ARE FORESEEN, EMPTY THE
BOILER AND THE HYDRAULIC SYSTEM TO
AVOID BREAKAGE IN THE TUBES DUE TO
THE FREEZING OF THE WATER.
CLEANING AND MAINTENANCE
The programmed maintenance of the
appliance must be carried out annually by
authorised technical staff.
LIGHTING AND OPERATION
SPIA VERDE
Fig. 1
SPIA GIALLASPIA ROSSA
Fig. 2
GREEN LED
RED LED YELLOW LED
VERY IMPORTANT!
PLEASE MAKE SURE YOUR BENCHMARK CHECKLIST IN THE
INSTALLATION GUIDE, IS FILLED IN CORRECTLY.
ALL GAS SAFE REGISTER INSTALLERS CARRY A ID CARD.
THE REGISTRATION NUMBER SHOULD BE
RECORDED ON THE CHECK LIST.
YOU CAN CHECK YOUR INSTALLER IS GAS SAFE
REGISTERED BY CALLING ON 0800 408 5577

6
FAULTS FINDING
–Ignition failure (fig. 3)
If the burner fails to start the red led will
light up ( ).
To attempt starting it again, the selector
knob must be turned to the position ()
and released soon after, returning to the
summer ( ) or winter ( ) position.
If the failure should occur again, call
the authorised technical staff for assi-
stance.
–Insufficient water
pressure (fig. 4)
If the red led “0.5 bar” intermittently
lights up, the boiler is not functioning. To
restore functioning fill the system until
the green led “1 bar” lights up.
If all the leds are off, call the authorised
technical staff.
–Safety stat interception (fig. 5)
If the safety stat intercedes the red led
“35°C” intermittently lights up. To start
the boiler again, turn the selector knob in
the position () and then release imme-
diately, returning it to the winter () or
summer ( ) function .
If the failure should occur again, call
the authorised technical staff for assi-
stance.
SPIA ROSSA
Fig. 3
Fig. 4
RED LED
SPIA ROSSA INTERMITTENTE
IN CONDIZIONE DI SICUREZZA
SPIA VERDE IN CONDIZIONE
DI FUNZIONAMENTO
SPIA ROSSA INTERMITTENTE
Fig. 5
FLASHING RED LED
IN SAFETY CONDITION
GREEN LED IN
OPERATING MODE
FLASHING RED LED

7
–Other faults (fig. 6)
When one of the leds is flashing from
“40÷ 80°C”, deactivate the boiler and
try to start it again. The operation may
be repeated 2 or 3 times, and if there is
no success call the authorised technical
staff for assistance.
Fig. 6
SPIA ROSSA INTERMITTENTE
FLASHING RED LED
MECHANICAL TIME CLOCK
INSTRUCTIONS
Setting the time
Turn the clock dial in a clockwise direction
until it reads the time of the day.
Program setting
Press inwards the segments on the pro-
gram disk corresponding to the selected
switching periods.
Function 1: segment set outwards (C.H. “ON”)
Function 2: segment set inwards (C.H. “OFF”)
Manual override
0 = “OFF” permanently
= automatic programmed operation
1 = “ON” permanently
Programming characteristics
Cycle 24 hour
Number of actions per cycle 96
Program time per segment 15 min.
Min. interval between two actions 15 min.
DIGITAL TIME CLOCK INSTRUCTIONS
When the selector is in the “AUTO” position,
boiler functioning is automatically controlled
on the basis of the temperature levels and
time periods set. The second selector must
be in the “RUN” position to start. The pro-
gramming procedure is described below:
- Setting the time
Set the selector to the ““ position.
Press “h” to change the hour on the
display, or “m” to change the minutes.
To set the day, press the “1…7” button
until the arrow is pointing to the correct
day (1 = Monday… 7 = Sunday).
- Setting the program
The time clock has 8 on times and 8 off
times. To make it easier to use, the time
clock is supplied with 3 on times and 3 off
times already set for each day of the
week, as shown below:
To select programmes other than those
already set, move the selector to position
“P”; “0:001” will appear on the display, in
which the first three digits indicate the
hour and minutes, while the fourth digit
identifies the program number.
Odd-numbered programs identify reque-
sts for operation (day temperature), in
which case the light bulb symbol will
appear on the display, while even-numbe-
red programs identify drops in tempera-
ture (night). Use the “1…7” key to select
the day of the week (from 1 to 7) or days
(1 ÷ 5, 6 - 7; 1 ÷ 6 or every day if the pro-
gram is to be repeated every day of the
week). Set the hour and minutes with the
“h” and “m” buttons.
Press “P” to store the operation in
memory and go on to the next program.
Repeat the same procedure to set the
remaining programs.
When finished programming, set the
selector to “RUN” position.
Fig. 7
Program Time Operating mode
1 06,00 ON
2 09,00 OFF
3 12,00 ON
4 14,00 OFF
5 18,00 ON
6 22,00 OFF
Note: No program is set from 7 through 17
or
Mechanical time clock
Digital time clock

8
When “ PLANET SUPER 4 F.S. ”is connec-
ted to the “Logica Remote Control”
regulator, the selector
CR/OFF/EST/INV/UNBLOCK must be
placed in the position ( ); the knobs of
the D.H.W. and C.H. potentiometers do
not have any effect and all of the func-
tions will be managed by the regulator
(fig. 9).
If the “Logica Remote Control” breaks
down, the boiler will function by placing
the selector on the ( or ), posi-
tion, obviously without consequent con-
trol of the room temperature.
The functioning instructions are inside
the lid (fig. 10). Every setting or modifi-
cation is displayed and confirmed on
the display (fig. 11).
LOGICA REMOTE CONTROL
1
67
8
4
5
3
2
KEY
1 Display
2 Info key
3 Operating mode key: automatic functioning
4 Operating mode key: manual functioning
5 Operating mode key: availability
6 Lid with instructions space
7 Temperature knob
8 On-line key Fig. 10
KEY
1 Digits, hour
2 Heating programme
3 Unit (%/°C)
4 On-line key display
5 External temperature
6 Room temperature
7 Vacation function
8 Operating mode
9 Line number, day
10 Burner lit
11 Heating functioning
12 Hot water temperature/load hot water Fig. 11
Fig. 9
- Deleting one or more
programs (fig. 8)
The on and off time must be deleted for
each program to be deleted.
Set selector (2) to position “P”. Select the
desired program with button (3), then
press button (4) to delete the day setting
(the triangular symbols for the days
should go away). If part of the program is
deleted, when you set selector (2) back
to the “RUN” position an error will appear
in the clock display, referring to the pro-
gram which is incorrect.
To delete all programs, put the selector in
position “P” and press buttons (3) and (5)
at the same time.
- Setting the SKIP function (fig. 8)
The SKIP function deactivates programs
for the next day and resumes regular
programming 24 hours later.
This function is useful if you will be out all
day and don’t need heating. To start this
function, press button (7), which is acti-
ve only when selector (2) is in “RUN”
position.
Once you have selected the SKIP func-
tion, it will go into effect at 0:00 of the
next day for 24 hours. You cannot turn it
off once it has started, so regular pro-
gramming will not resume until 24 hours
have passed.
1 Manual/automatic
operation selector
2 Program/schedule
setting selector
3 Program button
4 Day of the week button
5 Hour button
6 Minute button
7 SKIP button
8 Reset button
Fig. 8

If it is too hot or too cold in your apartment, you can easily adjust the fixed
temperature with the temperature knob.
Before adjusting it again, however, allow the temperature to stabilise first.
Note: With the temperature knob you can only adjust the fixed temperature, whilst the redu-
ced temperature remains the same.
–Adjusting the temperature
If you turn the knob towards the + sign, the fixed temperature is
increased by about 1 °C for every notch.
If you turn the knob towards the - sign, the fixed temperature is
decreased by about 1 °C for every notch.
Before adjusting the temperature of the regulator, the thermostatic valves, which may be
present, have to be regulated to the desired temperature.
For every operation of the Info key the fol-
lowing list of items, one after the other, are
displayed. The thermosensor continues to
function independently of the display.
Day, hour, room temperature
External temperature*
D.H.W. temperature*
* This data appear only if the relative sensor
is connected or if they are transmitted by
the regulator of the boiler.
–Info key
(reference key grey colour)
The operating mode desired is selected by
pressing the relative key with the correspon-
ding symbol. The choice is displayed with the
symbol
Automatic functioning: the heating functions automatically according to the hea-
ting programme entered. The programme may be excluded for brief periods with
the on-line key.
Manual functioning: the heating functions manually according to the choice made
with the on-line key.
Availability: the heating is deactivated.
–Selection of the operating mode
(reference keys grey colour)
ACTIVATING
During operation the lid of the regulator must be closed.
9

10
If the rooms remain unused for a long period of time, the temperatu-
re can be reduced with the on-line key, in this way saving energy. When
the rooms are occupied again, press the on-line key to re-heat them.
The current choice is displayed on the display:
–On-line key
Fixed temperature heating
Reduced temperature heating
NOTA:
In automatic mode, the apparatus switches from the fixed temperature to the reduced tem-
perature according to the temporal programme. The manual switching of the temperature is
done manually with the on-line key.
–Temperature regulation
Fixed temperature:
temperature when the rooms are occupied
(basic setting)
Reduced temperature:
temperature during periods of absence or night
Comfort D.H.W. temperature:
desired temperature of domestic hot water
Reduced temperature of domestic hot water:
temperature desired for domestic hot water at reduced level.
To have access to the “reduced D.H.W. temperature” parameter, press the and
keys at the same time for at least 5 seconds and then go along the entered
lines with the key until parameter 61 is reached. Regulate the value with
and .
Before proceeding with the adjustment in the temperature on the regulator, the thermostatic
valves, which may be present, have to be regulated to the desired temperature.
1
2
3
61
PROGRAMMING
For the programming the lid of the regulator must be open.
As soon as the cover is open,
the display and the key functions
are switched on.
The number in the square
represents the programme
lines that may selected with the
arrow keys.
You can set or display the following values:
• Temperatures up to
• Heating programme up to
• Day of the week and hour up to
• Current values up to
• Vacation period
• Return to the default values
13
411
12 14
15 17
18
19
The choice made will work in a permanent way when manually , carried out, instead, if
automatic it will work up to the next switching according to the heating programme.

11
–D.H.W. programme
Select the days that correspond with the heating phase.
1= Monday, ... 7 = Sunday/8 = hot-water service programme
Start of phase 1: heating with fixed modality
End phase 1: heating with reduced modality
Start phase 2: heating with fixed modality
End phase 2: heating with reduced modality
Start phase 3: heating with fixed modality
End phase 3: heating with reduced modality
Copying of the daily programme
By pressing this key it is possible to repeat the current heating programme
for the next day.
By pressing this key it is possible to repeat the current heating programme
for the previous day.
As a confirmation the following day is displayed.
4
5
6
7
8
9
10
11
With the Logica Remote Control it is possible to manage the temperature of D.H.W. tank on
two levels (a comfort level and one at reduced temperature) in accordance with the program-
me chosen with parameter 62 (load domestic hot water). To have access to the parameter
press the and keys for at least 5 seconds and then go along the entered lines with the
key until parameter 62 is reached. At this point four different programmes may be selec-
ted with o keys, with the following characteristics:
0= 24 hours/ day - Hot water is always available at the temperature set with user parame-
ter n°3.
1= standard - Hot water according to the daily heating programme.
In the comfort areas of heating the temperature of the D.H.W. tank is regulated to the
value set with user parameter n° 3.
In the reduced areas of heating the temperature of the D.H.W. tank is regulated to the
value set with parameter n° 61 of the service level.
2= service disconnected
3= second daily programme (8) - Every day of the week the temperature of the hot water is set
according to programme 8. In this case there is a single programming for all the days of the
week and three time zones are available. In the time spans set the temperature of the D.H.W.
tank is regulated according to that set in parameter n°3. In the remaining hours the D.H.W.
tank is controlled to the temperature set with parameter n° 61 the of service level.
Start phase 1: preparation of the D.H.W. tank to the comfort temperature
End phase 1: Temperature of D.H.W. tank maintained at the reduced value
Start phase 2: Preparation of D.H.W. tank to the comfort temperature
End phase 2: Temperature of D.H.W. tank maintained at the reduced value
Start phase 3: preparation of D.H.W. tank to the comfort temperature
End phase 3: Temperature of D.H.W. tank maintained at the reduced value
5
6
7
8
9
10
–Heating programme With the heating programme it is possible to set the switching times of the temperature for a
period of a week. The weekly programme consists of 7 daily programmes. One daily program-
me allows 3 phases of heating. Each phase is defined by a ignition time and a finishing time. The
n° 8 daily programme is for the domestic hotwater service. If a phase is not required, the same
ignition and finishing time may be entered.

12
–Default values To take the setting to the default values, press the and keys at the
same time for at least 3 seconds. As confirmation a sign will appear on the display.
19
ATTENTION
The values of the following line numbers previously entered will be lost.
• Temperature and time programme to
• Vacation period
110
18
–Vacation function To enter the number of days of absence.
In the display the vacation symbol will be shown ( ), on the left the day of activa-
tion (1 = Monday/7 = Sunday) and on the right the number of vacation days.
18
During the vacation the regulator will be on the availability mode.
When the set days have elapsed, the regulator will go on to the automatic function.
NOTE:
The vacation period may be cancelled by pressing a key of the operating mode.
–Current values Display and setting of the gradient of the heating characteristics curve.
When the room temperature set is not reached choose the gradient
indicated in point 2.10.3
Display of the current boiler temperature.
Display of the current power of the burner and of the current operating mode
( = = heating/ = D.H.W. service)
15
16
17
–Setting the time To set the current day of the week
(1 = Monday/7 = Sunday)
To set the current hour
To set the current minute
Once the hour is completed, the setting of the hour changes.
12
13
14
With and keys the current hour is regulated. Pressing these keys together, the
regulation is speeded up in an increasing sense.

13
Smoke pressure switch does not return to rest position
Call the authorised technical staff for assistance.
66
68
69
70
192
193
194
195
C.H. sensor fault (SM)
Call the authorised technical staff for assistance.
Insufficient water pressure
Restore functioning by filling the boiler.
System overpressure
Call the
authorised technical staff for assistance.
Safety stat interception
Call the
authorised technical staff for assistance.
Smoke pressure switch interception
Call the
authorised technical staff for assistance.
Failure of the modulating coil
Call the
authorised technical staff for assistance.
Communication failure between the Logica Remote Control and the boiler
Call the
authorised technical staff for assistance.
1
0
–Display of the functioning faults on the display
Ignition failure
Turn the selector CR/OFF/EST/INV/UNBLOCK on the “PLANET SUPER 4 F.S.” control panel to
the unblock position ( ) to restore functioning (fig. 3). If the failure should occur again, call the
authorised technical staff for assistance.
Safety stat interception
Turn the selector CR/OFF/EST/INV/UNBLOCK of the “PLANET SUPER 4 F.S.” control panel
to the unblock position () to restore functioning (fig. 5). If the failure should occur again, call
the authorised technical staff for assistance.
Smoke pressure switch failure
Call the authorised technical staff for assistance.
16

14

Cod. 6258913 - 02/11 - Documentation Dpt.
Sime Ltd
1a Blue Ridge Park
Thunderhead Ridge
Glasshoughton, Castleford, WF10 4UA
Phone: [phone]
Fax: [phone]
www.sime.ltd.uk
Email: [email protected]