Simplex 4001-9403 User manual

BSimplex
4001-9403 and -9404
Fire Alarm Systems
Installation and Operating
Instructions
0 1995 Simplex Time Recorder Co.
FA4-21-004 (574-047)
All specifications and other information shown were current as of publication. and are subject to change without notice.
Ed495
firealarmresources.com

Contact your local
Simplex Time Recorder Co.
Branch Office (listed in the
Yellow Pages under Fire Alarm)
for Warranty Registration &
Information.
firealarmresources.com

TABLE OF CONTENTS
IMPORTANT DEFINITIONS ................................................................................................................................... 1
SYSTEM INTRODUCTION .............................................................
........................................................
............... 1
INSTALLATION INSTRUCTIONS
Introduction ............................................................................................................................................................. 3
Tools and Equipment Required ............................................................................................................................... 3
General Notes ......................................................................................................................................................... 3
General Requirements for System Wiring .............................................................................................................. 4
System Wiring Specifications ................................................................................................................................. 4
Installation Check List ............................................................................................................................................. 6
INSTALLATION PROCEDURES
Control Panel Mounting ..........................................................................................................................................
a
Mounting and Wiring Peripheral Devices ................................................................................................................ 9
Building Wiring Checkout Procedure .................................................................................................................... 10
Control Panel Terminal Connections ..................................................................................................................... 11
Transient Suppressor, Zone Disconnect, or Combination Transient Suppressor/Zone Disconnect
Board Terminal Connections. ................................................................................................................................ 18
System Programming.. ......................................................................................................................................... 20
System Power-Up.. ............................................................................................................................................... 21
OPERATING INSTRUCTIONS
Introduction ........................................................................................................................................................... 23
How to Recognize Normal, Trouble, and Alarm Indications .................................................................................. 24
How to Operate the Panel During an Alarm Condition ......................................................................................... 24
How to Reset the Fire Alarm System Following an Alarm Condition .................................................................... 25
How to Operate the Panel when Water is Flowing in the Sprinkler System ......................................................... 25
What to Do in Case of Trouble .............................................................................................................................. 26
Alarm Verification Feature .................................................................................................................................... 26
Troubleshooting .................................................................................................................................................... 27
How to Test the System ........................................................................................................................................ 28
How to Perform the LED Test ............................................................................................................................... 29
BATTERY TESTING INFORMATION
General Information .............................................................................................................................................. 30
Testing ......................................................................................................................................................... ......... 30
Pk
I
-J
CAUTION
ELECTRICAL HAZARD
Disconnect electrical power when making any
internal adjustments or repairs. Installation and
servicing should be performed by qualified Simplex
Representatives.
I
These instructions only apply to United States installations.
i
firealarmresources.com

firealarmresources.com

IMPORTANT DEFINITIONS
Alarm-Initiating Device: A device which, when actuated, initiates an alarm. Such devices, depending on their type,
can be operated manually or actuated automatically in response to smoke, flame, heat or water-flow. (Examples: pull
stations, heat detectors, smoke detectors, sprinkler flow switches, etc.)
Alarm-Notification Appliance: A device that produces an audible and/or visual alarm signal in response to a fire
emergency. (Examples: horns, bells, chimes, flashing lights, etc.)
Annunciator: An electrically operated visual signaling device having one or more lamps or LEDS to display the
status of the fire alarm system.
End-of-Line Device: A device used to terminate a supervised circuit.
Initiating-Device Circuit: A circuit to which automatic or manual initiating devices are connected.
Local Energy Master Box: A municipal master box that uses electrical energy from the protected premises to
energize its electromagnetic tripping mechanism. See definition for shunt master box.
Notification-Appliance Circuit: A circuit to which notification appliances are connected.
Shunt Master Box: A municipal master box that uses electrical energy from the municipal fire alarm system to
energize its electromagnetic tripping mechanism. See definition for local energy master box.
Zone: A designated area of a building. Commonly, zones within a building are annunciated to aid in locating a fire.
SYSTEM INTRODUCTION
The 4001-9403 and -9404 are four-zone, electrically supervised, fire alarm panels.
l The 4007-9403 connects to a 12OVAC 60 Hz source.
l The 4007-9404 connects to a 220/24OVAC, 50 Hz source.
Each system contains one notification appliance circuit, battery standby power, and battery charger.
The systems provide an early warning evacuation signal for building occupants if a fire occurs. The systems consist
of:
l Alarm-initiating devices - Smoke detectors, heat detectors, pull stations, etc.
l Alarm-notification appliances - Horns, bells, and visual units.
l A control panel.
Each system may also contain optional features.
Since the -9403 and -9404 operate the same except for input power, we will discuss system operation as it applies
to the -9403.
Alarm-initiating devices are installed in the building and connected to one of four initiating-device circuits on the
control panel. Each initiating-device circuit is given a zone number (1, 2, 3, or 4). Thus, the various areas of the
building can be designated as zone 1, zone 2, zone 3, or zone 4. The control panel monitors each zone for troubles
and alarms.
1
firealarmresources.com

SYSTEM INTRODUCTION - Continued
Alarm-notification appliances are located throughout the building to provide acceptable sound levels. These
appliances are connected to a notification-appliance circuit on the control panel. The control panel activates the
notification appliances from a central location.
You operate the system using the LED indicators and switches on the control panel. When an alarm or trouble
condition exists, the panel LEDs indicate the location and type of condition.
l Red LEDs indicate an alarm condition when on.
l Amber LEDs indicate a trouble condition when on.
Switches allow you to interact with the system in various ways (see Operating Instructions on Page 23).
A diagram of a typical system is shown in Figure 1.
3.3K. 1W. 5%
9
ANNUNCIATOR
10K. l/ZW.S% 3.3K. 1W. 5%
- 1 CONTACTS RATINGS ZA.@ 30 VACWDC
CONNECT TO
120 VAC
SOHZ
(FUSED
SOURCE)
PANEL DRAWS
1.2A
9 +
JW3
GND
F3
SIG CKT
-.
BRN
OUT 0
F2
AUX PWR
0.75A xx
0
PWR
TBL
Fl
AC INPUT
K2 r
JW2
JWl
0 :
3
:
6
,
ITROUBLE I
cc+ 1
r”ztt F4
BAlTERY ow
xxmm
WEea
1
FIGURE 1
2
OPTIONAL
RIBBON -
CABLE
OPTIONAL
TRANSIENT
SUPPRESSOR. ZONE
DISCONNECT. OR
TRANSIENT
SUPPRESSOR ZONE
DISCONNECT BOARD
--w
I
firealarmresources.com

INSTALLATION INSTRUCTIONS
INTRODUCTION
Be sure that you are thoroughly familiar with this installation procedure before installing the system.
To help you with the installation of this and other Simplex systems, the following publication is available for general
reference: How to Wire a Building for a Fire Alarm System.
TOOLS AND EQUIPMENT REQUIRED
l l/4-Inch Flat-tip Screwdriver, 8-Inches long
l l/8-Inch Flat-tip Screwdriver, 4-Inches long
l Volt-ohmmeter
l Diagonal Cutting Pliers
0 Wire Strippers
l End-Of-Line resistors (EOLRs) (supplied by Simplex): five 3.3K, 1 watt resistors; two 1OK, l/2 watt resistors; two
lK, 1 watt, resistors
l System Wiring Diagram 841-610.
GENERAL NOTES
l Notify appropriate personnel (building occupants, fire department or monitoring facility, etc.) of the installation.
l When running wires to control panel, identify wires appropriately: 12OVAC input power, notification (signal) circuit,
zone 1, zone 2, etc., and identify all ‘I+” wires and ‘I-” wires.
l The panel’s terminal boards are labeled with a TB number (TBI, TB2, TB3, etc.), and each terminal is designated
a terminal number (1, 2, 3, etc.). Therefore, TBl-1 is terminal 1 on terminal board TBl, TBl-2 is terminal 2 on
terminal board TBl, etc. Each terminal is also identified with an abbreviation of the circuit wire that is to be
connected to it (SIG -, SIG +, ZONl -, ZONl+, etc.).
l Use the following resistor color code (Fig. 5) to identify the end-of-line resistors (EOLRs) used in the installation:
ORANGE
ORANGE
RED
GOLD
3,300-OHM (3.3K, 1 WAlT)
RESISTOR
BROWN
BLACK
ORANGE
GOLD
lO,OOO-OHM (lOK, l/2 WATT)
RESISTOR
BROWN
BLACK
RED
GOLD
1,OOO-OHM(1K, 1 WAlT)
RESISTOR
FIGURE 2
3
firealarmresources.com

GENERAL NOTES - Continued
l All wiring must be in accordance with local codes.
l All wiring should be in accordance with National Electric Code, Article 760.
l A neatly wired system will help assure an accurate inspection of all connections and simplify troubleshooting.
GENERAL REQUIREMENTS FOR SYSTEM WIRING
These requirements are intended to aid the installer in making a safe and trouble-free installation, but they are not
intended to circumvent any pertaining and/or required codes, laws, regulations, etc.
Note: These wiring specifications are subject to local authority approval.
General Wiring Requirements For Fire Alarm Systems
1. All wires are to be copper conductors only.
2. All wiring, except incoming power and ground connecting wires, must be free from grounds or shorts and have
a resistance of one megohm, or higher, to earth.
3. Metallic conduit, metallic raceway, plastic pipe, or plastic raceways may be used.
If metallic conduit is used, the following must be observed: If the continuity of the metallic conduit is not
maintained, then a 12AWG (minimum) drain wire must be used between the break of metallic conduit. The drain
wire will be connected to the metallic conduit at both ends.
4. Only system wiring can be run in the same conduit, pipe raceway, or multiconductor cables.
5. Where system wires pass through floors or fire-rated walls, the installation shall be made to prevent the spread
of fire from floor to floor (i.e. patching of holes, fire stops, etc.).
6. All system wiring subject to physical damage shall be mechanically protected based on the environment the
cable is subjected to.
7. Each device - pull station, detector, horn, bell, etc. - must have its own enclosure such as a back box, outlet
box, etc.
8. A minimum of 6 inches of free conductor will be required in each electrical box to facilitate terminations. A 12-
inch service loop of cable is required for all continuous pulls through an electrical box.
9. Unused openings in electrical boxes shall be properly “blanked off” with suitable protection equivalent to the
wall thickness of the equipment. All splice boxes shall have a blank cover.
10. All wiring shall be terminated with U.L. listed devices (i.e. wire nuts, pressure connectors, etc.). Wiring
terminated with only electrical tape is not permitted. All splicing (free ends of conductors) shall be covered with
an insulation equivalent to that of the conductors.
SYSTEM WIRING SPECIFICATIONS
Incoming Power Wiring
Source - Life Safety Branch Circuit, or as required by local code.
Panel draws 2A maximum at 12OV, 60Hz via a fused disconnect or circuit breaker.
Wiring - Use two 14 AWG wires, or 14AWG cable.
4
firealarmresources.com

Earth Detection
Source - Connection shall be made to an approved dedicated earth connection per NEC Article 250 (NFPA 70).
Wiring -Use 14AWG wire.
Alarm-Initiating Device Wiring
Alarm-initiating devices - Manual pull stations, automatic heat detectors and automatic smoke detectors.
Wiring - Four circuits with two wires per circuit. Each circuit terminates with a 3.3K end-of-line resistor. Use 18AWG
to 14AWG wire.
Note: If using 4-wire detectors, refer to Step 4 (page 9). The “RMT +I’ output used can supply up to 500MA of
filtered, regulated 24VDC.
Max. loop line resistance for each circuit is 50 ohms if P-wire detectors are used.
Alarm-Notification Appliance Wiring
Afarm-notification appliances - Horns, bells and visual units.
Wiring - 2-wire circuit terminating with a 1OK end-of-line resistor. Use 18AWG to 14AWG wire.
Note: Because the system’s total signal power is 2A, the number of notification appliances and the wire length that
can be used in the notification circuit is limited. Refer to Table 1 to determine the maximum number of
notification appliances and the total wire length that can be used in the notification circuit.
TABLE 1
firealarmresources.com

SYSTEM WIRIING SPECIFICATIONS - Continued
Auxiliary Alarm Relay Contacts (If Used)
Devices - Damper and fan controls, smoke door releases, elevator control, etc.
Source - External 3OVAC/3OVDC @ 2A, dependent upon devices that are used.
Wiring - Two Form C contacts available which transfer upon automatic alarm. Use 18AWG to 14AWG wire.
Trouble Relay Contacts (If Used)
Devices
- Horns, bells, lights, etc.
Source - External 3OVAC/SOVDC dependent upon devices that are used. Max. load is 2A resistive.
Wiring - One Form C contact available which transfers upon a trouble condition. Use 18AWG to 14AWG wire.
INSTALLATION CHECK LIST (REFER TO WIRING DIAGRAM 841-610)
This section provides a systematic method for installing the system. Upon completion of a procedural step, place a
check mark in the appropriate box in the left column.
If a problem occurs with the installation, refer to the appropriate page listed in the right column of the checklist. The
information found on that page will provide a detailed description of a specific part of the installation. If your problem
is not resolved, contact your local Simplex Branch Office (listed in the Yellow Pages under Fire Alarm).
If you wish, you may go directly to the detailed instructions to install the system (Page 8).
INSTALLATION CHECK LIST
DETAILED
q
Procedure INSTRUCTION
SEE PAGE(S)
Mount control panel. If using optional modules, battery meter module and/or
q
1. alarm relay module, mount them using the instructions supplied with each 8
module.
q
2. If using external battery cabinet, install it. 8
Install peripheral devices and connect end-of-line resistors across terminals
q
3. of the last device in the notification-appliance circuit and initiating-device 9
circuits used.
q
4. Check building (system) wiring for absence of voltage, opens, and shorts. 10
Steps 5 through 21 describe the connections to the panel’s terminals.
q
5. Connect ground wire to green ground screw. 11 (Step 1A)
Connect notification-appliance circuit to TB2-5 (SIG +) and TB2-6 (SIG -).
q
6. (Connect circuit to transient suppressor or combination board if used [see 11 (Step 2)
pages 18 and 191).
Connect initiating-device circuits to appropriate terminals on TB4 (connect
circuits to transient suppressor board, zone disconnect board, or transient
q
7. suppressor/zone disconnect board if used [see pages 28 and 291). If system 11 (Step 3)
contains coded manual station, connect coded stations to terminals
designated for Zone 1 and cut jumper JW2.
6
firealarmresources.com

DETAILED
0 Procedure INSTRUCTION
SEE PAGE(S)
If 4-wire detectors are used, connect circuit for detectors to TB2-3 (AUX +)
0 8. and TB2-4 (AUX -). Connect TB3-9 (RMT +) to TB2-2 (EXT PWR) and cut 12 (Step 4)
jumper JW3.
0 9 If using an auxiliary power supply, connect it to TB2-2 (EXT PWR) and
TB2-4 (AUX -). Cut jumper JW3. 12 (Step 5)
If using a waterflow switch, connect as follows: Connect waterflow switch
(N/O) to TB4-5 (ZONE3 +) and TB4-6 (ZON3 -). Connect tamper switch
0 10. (N/C), if used, to TB4-7 (ZON4 +) and TB4-8 (ZON4 -). (Connect switches 13 (Step 6)
to transient suppressor board, zone disconnect board, or transient
suppressor/zone disconnect board, if used [see pages 28 and 291).
If using a remote annunciator, connect it to terminals on TB2 and TB3. If
0 11. supervision of annunciators is desired, and if alarm relay module is not
being used, remove appropriate jumpers JW4, JW5, JW6 and JW7 (refer to 13 (Step 7)
Table 4), and appropriate resistors R84, R85, R86, and R87.
If using an alarm relay module, connect it to terminals on TB2 and TB3. If
0 12. using with an annunciator, DO NOT REMOVE INDICATED ANNUNCIATOR 14 (Step 8)
JUMPERS OR RESISTORS.
0 13. If remote trouble devices are used, connect them to the trouble relay
terminals (TB3) 14 (Step 9)
0 14. If remote alarm devices are used, connect them to the auxiliary relay
terminals (TB5). 15 (Step 10)
0 15. Configure jumpers on JWl in accordance with Figure 21 15 (Step 11)
0 16. If city circuit is used, connect it to TB5-1 (CITY+) and TB5-2 (CITY -) 16 (Step 12)
0 17. Connect AC power to transformer leads. DO NOT APPLY POWER. 16 (Step 13)
0 18. Connect batteries as indicated. DO NOT CONNECT WHITE BATTERY
WIRES NOW. If used, connect battery meter module to batteries. 16,17
El 19. Set DIP switch package SW1 in accordance with Table 4. 20
0 20. Apply system power. 21 and 22
01 21. 1Test the system.
I
28
7
firealarmresources.com

INSTALLATION PROCEDURES
CONTROL PANEL MOUNTING (Refer to Figure 3)
1. Unlock and open panel door.
2. Unsnap and remove panel overlay from circuit card.
3. Remove knockout plugs on box assembly for wire entry.
4. At control panel mounting location, position control panel and secure with fasteners which are capable of
supporting panel with batteries. Holes are provided at rear of box for securing panel to wall.
5. Enter external wires into control panel.
l For semi-flush mounting, install trim panel and secure with six screws.
6. If using transient suppressor, zone disconnect, or combination transient suppressor/zone disconnect board,
install board as follows:
a. Secure hex spacers to studs on box assembly.
b. Align board with spacers and secure with four screws.
c. Connect cable to board and control panel as shown (blue edge of cable should line up with pin 9 on each
connector).
7. If using external battery cabinet, mount it using the instruction provided with the cabinet. The battery cabinet
should be close-nippled to the control panel (maximum two feet apart).
8. If using battery meter module or alarm relay module, mount it using the instructions provided with the module.
Make sure the module is within six inches of the control panel.
9. PERFORM THIS STEP ONLY IF PANEL USES ALARM VERIFICATION.
An alarm verification label (P/N 519-532) is provided with the control panel. In the space labeled “CIRCUIT
(ZONE),” indicate the zones for which alarm verification is used. (Refer to Notes 2 and 3 on Page 26.)
In the space labeled “CONTROL UNIT DELAY-SEC,” enter the number “41.”
10. If required by local codes, install the red 4001-9812 peel-and-stick applique on the control panel door using the
instructions provided with the applique.
MOUNTING HOLES
CIRCUIT CARD
BOX ASSEMBLY SUPPRESSOR
SUPPRESSOR/ZONE
DISCONNECT BOARD
NOTE: DO NOT ENTER
WIRES AT BATTERY
LOCATION.
FIGURE 3
8
firealarmresources.com

MOUNTING AND WIRING PERIPHERAL DEVICES (REFER TO WIRING DIAGRAM 841-610)
1. Determine mounting locations of peripheral devices and install system wires from the mounting location of each
peripheral device to the control panel via junction boxes (if used):
2. Install wires for the panel’s input power.
WARNING: DANGEROUS VOLTAGE (120VAC) MAY EXIST AT POWER INPUT. MAKE SURE PROPER
CIRCUIT BREAKER OR FUSED DISCONNECT SWITCH AT BUILDING’S POWER DISTRIBUTION
IS SET TO THE OFF POSITION.
3. Install all peripheral devices (detectors, horns, pull stations, etc.) and connect them to the appropriate wires
(refer to the installation instructions packed with the devices). Connect a 3.3K end-of-line resistor (EOLR)
across the terminals of the last device in each initiating circuit and mark the device accordingly (see Figure 4).
Connect a 1OK EOLR across the terminals of the last device in each notification appliance circuit and mark the
device accordingly (see Figure 5).
~~&lA&lNG -
CIRCUIT
(ZONE 1,2,3, OR 4)
NOTIFICATION -
tJV’bT;CE
FIGURE 4 FIGURE 5
4. If any of the designated zone terminals on the panel do not have initiating devices connected to them, connect
a 3.3K EOLR across those terminals (Fig. 6). (If using the transient suppressor, the zone disconnect, or
combination board, see page 18.)
TB4
WHEN NO WIRES ARE
CONNECTED TO ZONE
(INITIATING) TERMINALS,
CONNECT A 3.3K EOLR
ACROSS THOSE TERMINALS.
FIGURE 6
9
firealarmresources.com

BUILDING WIRING CHECKOUT PROCEDURE (REFER TO WIRING DIAGRAM 841-610)
1. Check notification-appliance and initiating-
device circuits for absence of voltage, shorts,
or opens as follows:
A. At the control panel, locate the notification-
appliance or one of the initiating-device
circuits.
B. Set volt-ohmmeter to 300VAC.
C. Place meter probes so that black probe is
on I‘-” wire and red probe is on I‘+” wire.
Volt-ohmmeter should read OV (Fig. 7). If
you read a voltage, check circuit wiring.
D. Set volt-ohmmeter to GOVDC and repeat
step 1C.
E. Set volt-ohmmeter to OHMS X 10 and place
meter probes as described in Step 1C.
If reading indicates no continuity (open
circuit, see Fig. 8) or a short circuit (see Fig.
9), locate and correct open/short in circuit.
Note: If reading indicates an open circuit in
an initiating circuit, make sure that all
smoke detector heads are mounted
and seated in their bases.
F. Repeat Steps 1A thru 1E for all zone
circuits.
2. Check system’s other external circuits as
follows:
A. Locate wires for each of the systems circuit
not yet tested.
B. Check for voltage on circuit as described in
Steps 1B thru 1D.
C. Set volt-ohmmeter to OHMS X 10 and place
meter probes across circuit being tested
Reading should indicate an open circuit
(Fig. 8).
If reading indicates a short circuit (Fig. 9) or
something less than infinity (-), check
circuit wiring.
Notes: 1. Normally-closed (N/C) relay circuits
(auxiliary relays and trouble relay) will
correctly read 0 ohms.
2. City circuit (if.used) will read 15 to 5000
ohms depending on type of city
connection.
D. Repeat Steps 2A thru 2C for the external
circuits not yet checked.
THIS READING
INDICATED NO
FIGURE 7
NORMAL RANGE
THIS READING
INDICATES AN
OPEN CIRCUIT
FIGURE 8
NORMAL RANGE
THIS READING
INDICATES AN
OPEN CIRCUIT
FIGURE 9
10
firealarmresources.com

CONTROL PANEL TERMINAL CONNECTIONS (REFER TO WIRING DIAGRAM 841-610)
Note: The panel must be connected to a separate
earth ground per Article 250 of the National
Electrical Code (NFPA 70).
1. Connect earth ground detection circuit as
follows:
A.
B.
Connect ground wire to green ground
screws (Fig. 10) on box assembly.
Connect other end of ground wire to an
approved earth ground (metallic cold water
pipe, driven ground rod, etc.).
GREEN GROUND
SCREW
FIGURE 10
2. Connect indicating appliance circuit to TB2-5 (SIG +) and TB2-6 (SIG -) (Fig. 18).
Note: If the system contains the transient suppressor board, connect notification circuit to
instead of the panel terminals (see Page 18).
TO NOTIFICATION
APPLIANCE CIRCUIT
(IF SUPPRESSOR/
DISCONNECT
BD IS NOT USED)
the suppressor board
TRANSIENT
FIGURE 11
3. Connect initiating (zone) circuits to the following terminals (refer to Table 3 and Fig. 12).
TO INITIATING CIRCUITS
(IF SUPPRESSOR/DISCONNECT BD IS NOT USED)
TABLE 3
JW2 /
ZONE TERMINALS
1 TB4-1 (ZONl +) & TB4-2 (ZONl -)
2 TB4-3 (ZON2 +) & TB4-4 (ZON2 -)
3 TB4-5 (ZON3 +) & TB4-6 (ZON3 -)
4 TB4-7 (ZON4 +) & TB4-8 (ZON4 -) FIGURE 12
11
firealarmresources.com

CONTROL PANEL TERMINAL CONNECTIONS - Continued
Notes: 1. If the system contains the transient suppressor board, the zone disconnect board, or the transient
suppressor/zone disconnect board, connect initiating device circuits to the suppressor or disconnect
board instead of the panel terminals (see Page 18).
2. If any of the designated zone terminals do not have alarm devices connected to them, a 3.3K EOLR must
be connected across those terminals (or the appropriate terminals on the suppressor board or zone
disconnect board, if used).
3. If the system contains the waterflow/sprinkler feature, connect waterflow-initiating devices to terminals
designated for zones 3 and 4 (see Page 13).
4. If the system contains coded manual stations, connect stations to zone 1 and cut jumper JW2 (Fig. 12).
4. If the system contains 4-wire detectors, do the following:
A. Connect a wire between the RMT + terminal (TB3-9 [Fig. 16, Page 141) and the EXT PWR terminal (TB2-2).
B. Cut jumper JW3 on the control panel as shown in Figure 13.
C. Connect the wires used to power the detectors as shown in Figure 13.
TB3
TB2
FIGURE 13
5. If using a 24VDC auxiliary power supply, cut jumper JW3 and connect the supply as shown in Figure 14. USE
OF EXTERNAL POWER MAY VOID POWER LISTING ON THAT CIRCUIT.
CAUTION: Make sure that power is not connected to the auxiliary power supply throughout the installation. Its
voltage (24VDC) may cause damage to the panel during the installation.
TB2
FIGURE 14
12
firealarmresources.com

6. If waterflow/sprinkler switch circuits are used, connect as follows:
A. Connect the waterflow switch (normally open) as shown in Figure 15. Make sure 3.3K resistor is connect to
circuit as shown in wiring diagram 841-610.
B. Connect the sprinkler tamper switch (normally closed) as shown in Figure 15. Make sure resistors (1K and
820 ohm, 1 watt) are connected to circuit as shown in wiring diagram 841-610.
Note: If the system contains the transient suppressor, zone disconnect or transient suppressor/zone disconnect
board, connect the waterflow/sprinkler circuits to the board instead of the panel terminals (see Page 18).
TO WATERFLOW SW AND SPRINKLER
TAMPER SW (IF SUPPRESSOR/DISCONNECT
ED IS NO_TUSED)
FIGURE 15
7. If using a remote annunciator or remote annunciator with remote trouble station and remote acknowledge
switch, connect to panel as follows (see Fig. 16, page 14, for reference):
Notes: 1. Perform only Steps 7A through 7C if you are installing the 4601-9101 remote annunciator.
2. Perform Steps 7A through 7E if you are installing the 4601-9102 remote annunciator with trouble and
acknowledge.
A. Connect the annunciator “ - ” wires as indicated in Table 2.
B. If supervision of annunciators is desired, remove the appropriate jumper(s) and resistor(s) indicated in Table
2.
C. Connect the RMT + wire to TB3-9 (RMT +).
D. Connect the REM ACK wire to TB2-1 (REM ACK).
E. Connect the TBL RMT wire to TB3-8 (TBL RMT).
TABLE 2
I
ZONE I TERMINAL I JUMPER REMOVED RESISTOR REMOVED
(See Caution Below) (See Caution Below) I
1 TB3-4 (ANNl-) JW4 R84
2 (if used) TB3-5 (ANN2-) JW5 R85
3 (if used) TB3-6 (ANNS-) JW6 R86
4 (if used) TB3-7 (ANN4-) JW7 R87
CAUTION: If alarm relay module is used, DO NOT REMOVE JUMPERS OR RESISTORS!
13
firealarmresources.com

CONTROL PANEL TERMINAL CONNECTIONS - Continued
162
JW4 JW5 JW6 JW7
FIGURE 16
8. If 4100-9810 alarm relay module is used, connect it to TB2, TB3, and TB5 on the panel as follows (refer to
Figure 16):
A. Connect the relay module’s ANN1 wire (TBl-1) to TB3-4 (ANNl-).
Connect the relay module’s ANN2 wire (TBl-2) to TB3-5 (ANN2-).
Connect the relay module’s ANN3 wire (TBl-3) to TB3-6 (ANN3-).
Connect the relay module’s ANN4 wire (TBl-4) to TB3-7 (ANN4-).
B. Connect the relay module’s AUX- wire (TB2-8) to TB2-4 (AUX-).
Connect the relay module’s AUX+ wire (TB2-7) to TB5-6 (NO of AUXl).
C. Connect a wire from the panel’s RMT+ (TB3-9) to TB5-7 (C of AUXl).
D. Refer to wiring diagrams 841-610 for information on connecting external devices.
9. If remote trouble devices are used, connect them to trouble relay as follows (Refer to Fig. 17):
The trouble relay may be used to operate external circuits. These external circuits may contain horns, bells,
lights, or other devices associated with fire alarm systems.
Notes: 1. Trouble relay activates upon a trouble condition.
l Trouble silence switch activation turns off the trouble relay.
2. Trouble relay contacts are Form C dry contacts, and are rated 2A maximum at 30VACMOVDC
(resistive rating).
A. Connect positive (DC) or hot (AC) lead of voltage source to TB3-2 (the common [C] contact of the trouble
relay).
B. If devices are to be turned on during a trouble condition, connect lead from remote devices to TB3-3 (the
normally open [N/O] contact of the trouble relay); if devices are to be turned off during a trouble condition,
connect lead from remote devices to TB3-1 (the normally closed [N/C] contact of the trouble relay.
14
firealarmresources.com

FIGURE 17
10. If remotely controlled devices are used, connect them to auxiliary master alarm relay as follows (refer to Fig.
17):
The auxiliary relay may be used to operate external circuits. These external circuits may contain lights, fan
controls, door releases, or other devices associated with fire alarm systems.
Notes: 1. Relay will activate upon alarm.
2. Auxiliary relay contacts are Form C dry contacts and are rated 2A maximum at 30VAC30VDC (resistive
rating).
A. Connect positive (DC) or hot (AC) lead of voltage source to TB5-7 (the common [C] contact of the AUX 1
relay).
B. If devices are to be turned on during alarm, connect lead from remote devices to TB5-6 (the normally open
[N/O] contact of the AUX 1 relay). If devices are to be turned off during alarm, connect lead from remote
devices to TB5-8 (the normally closed [N/C] contact of the AUX 1 relay).
C. Repeat steps 1 thru 3 for the AUX 2 relay (if used). Use appropriate terminals TB5-4 (common). TB5-3
(normally open) and TB5-5 (normally closed).
City Connections
11. Configure jumper JWl as shown in Figure 18. (If unable to determine type of monitoring method being
connected to the panel, ask the municipal monitoring facility.)
Note: Jumper JWl is a header plug with plug-in jumpers. This plug is used to configure the-system when the city
feature is not used - or when using reverse polarity, local energy master box, or shunt city connections.
FOR REVERSE POLARITY FOR SHUNT FOR LOCAL ENERGY FOR NO CITY
JWl JWl CONNECTION
JWl
0 0
1
0
0 2
-3
7
-4
0 0 5
0 0
6
0 0 7
FIGURE 18
0
: 0
z
0 01
0
0 2
0 0 3
7
0 0 4
0 0 5
0 0 6
0 0 7
15
firealarmresources.com

CONTROL PANEL TERMINAL CONNECTIONS - Continued
12. If using a city circuit (municipal monitoring facility), connect it as shown in Figure 19.
FIGURE 19
WARNING: DANGEROUS VOLTAGE (1TOVAC) MAY EXIST AT POWER INPUT. MAKE SURE PROPER
CIRCUIT BREAKER OR DISCONNECT SWITCH AT BUILDING’S POWER DISTRIBUTION IS SET
TO THE OFF POSITION.
AC Power Connection
The -9403 control panel must be connected to 12OV
60Hz power, and all 120VAC wires must be routed
separately from other wires in the control panel.
(220/24OV 50Hz is used if your system is a 4001-
9404).
13. Connect black power lead (hot) to black lead
from transformer input. Connect white power TO 120 VAC
lead (neutral) to white lead from transformer
FUSED OUTLET
input (Fig. 20).
14. PERFORM THIS STEP ONLY IS USING THE BATTERY METER MODULE
Install the battery meter module using the instructions provided with it. Discard the harness shipped with the
control panel and use the harness supplied with the meter module.
Connect the battery meter module to the batteries as shown in Figure 21A. DO NOT
BATTERY JUMPER. ONox CONTROL LEA”EWHlTE
CONNECT WHITE
BLACK --
II
NOTE BATTERIES MOVNT IN CONTROL PANEL DO NOT
USE HARNESS SHIPPED WITH BATTERIES’
FIGURE 21A
Note: If using 18Ah batteries in an external cabinet without meter module, proceed to Step 16.
16
firealarmresources.com