Simplex LifeAlarm 4005 Series Installation manual

4005 Fire Alarm
Front Panel Programming
Instructions
574-059
Rev. D
Technical Manuals Online! - http://www.tech-man.com

this is blank text
Technical Manuals Online! - http://www.tech-man.com

i
Copyright 2000 by Simplex Time Recorder Company
All rights reserved. Simplex Plaza, Westminster, MA 01441
Printed in the United States of America.
Information in this document is subject to change without notice. No part of this
document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, without the express written consent of
Simplex Time Recorder Company.
Walk Testis protected by US Patent No. 4,725,818.
SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure
proper system operation, this product must be tested in accordance with
NFPA72-1996, Chapter 7 after any programming operation or change in site-
specific software. Reacceptance testing is required after any change, addition or
deletion of system components, or after any modification, repair or adjustment to
system hardware or wiring.
All components, circuits, system operations, or software functions known to be
affected by a change must be 100% tested. In addition, to ensure that other
operations are not inadvertently affected, at least 10% of initiating devices that
are not directly affected by the change, up to a maximum of 50 devices, must
also be tested and proper system operation verified.
READ AND SAVE THESE INSTRUCTIONS.Follow the instructions in the
installation, operating and programming manuals. These instructions must be
followed to avoid damage to the control panel and associated equipment. Fire
Alarm Control Panel (FACP) operation and reliability depend upon proper
installation and programming.
DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED.
Upon unpacking your Simplex product, inspect the contents of the carton for
shipping damage. If damage is apparent, immediately file a claim with the
carrier and notify Simplex.
ELECTRICAL HAZARD - Disconnect electrical power when making any internal
adjustments or repairs. Servicing should be performed by qualified Simplex
Representatives.
STATIC HAZARD - Static electricity can damage components. Therefore,
handle as follows:
1. Ground yourself before opening or installing components (use the
553-484 Static Control Kit).
2. Keep uninstalled component wrapped in anti-static material at all times.
RADIO FREQUENCY ENERGY - This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used in accordance with
the instruction manual, may cause interference to radio communications. It has
been tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take
whatever measures may be required to correct the interference.
Copyright and Trademarks
Cautions and Warnings
Technical Manuals Online! - http://www.tech-man.com

ii
The 4005 is listed for the following listing categories.
UL 864 Listings for Type of System:
•UL 864 Power-Limited Fire Alarm Control Unit.
•Local (formerly NFPA 72A).
Requires the sounding of an alarm via listed notification appliance(s).
•Auxiliary (formerly NFPA 72B).
Requires 4005-9809 City Circuit Module.
•Remote Station - protected premise (formerly NFPA 72C).
Requires 4005-9809 City Circuit Module or the 4005-9810 DACT.
•Proprietary - protected premise (formerly NFPA 72D).
Requires 4005-9809 City Circuit Module.
•Central Station - protected premise (formerly NFPA 71).
Requires 4005-9810 DACT.
UL 864 Listings for Type of Service:
•Automatic, Manual, Waterflow, and Sprinkler Supervisory.
UL 864 Listings for Type of Signaling:
•Coded, Non-Coded, March-Time, and DACT.
DACT requires 4005-9810 DACT.
• Same as UL above
•Intrinsically Safe (Requires 2081-9636, 2081-9062, or 2081-9063
Intrinsically Safe Barrier Module)
• CSFM
• MEA
Continued on next page
Codes and Standards
Factory Mutual Approved
Local Approvals
Technical Manuals Online! - http://www.tech-man.com

iii
The 1993 National Fire Alarm Code (NFPA 72) referenced publications are
listed below. The installer should be familiar with these codes, as well as any
applicable local codes and standards, when installing a fire alarm system.
• NFPA 72 National Fire Alarm Code
• NFPA 11 Standard for Low-Expansion Foam and Combined Agent
Systems
• NFPA 11A Standard for Medium- and High-Expansion Foam Systems
• NFPA 12 Standard on Carbon Dioxide Extinguishing Systems
• NFPA 12B Standard on Halon 1211 Fire Extinguishing Systems
• NFPA 13 Standard for the Installation of Sprinkler Systems
• NFPA 14 Standard for the Installation of Standpipe and Hose Systems
• NFPA 15 Standard for Water Spray Fixed Systems for Fire Protection
• NFPA 17 Standard for Dry Chemical Extinguishing Systems
• NFPA 70 National Electrical Code
• NFPA 80 Standard for Fire Doors and Fire Windows
• NFPA 90A Standard for the Installation of Air Conditioning and
Ventilation Systems
• NFPA 90B Standard for the Installation of Warm Air Heating and Air
Conditioning Systems
• NFPA 92A Recommended Practice for Smoke-Control Systems
• NFPA 92B Guide for Smoke Management Systems in Malls, Atria, and
Large Areas
• NFPA 101 Life Safety Code
• NFPA 170 Standard for Fire Safety Symbols
• NFPA 231C Standard for Rack Storage of Materials
• NFPA 1221 Standard on the Installation, Maintenance, and Use of Public
Fire Service Communication Systems
NFPA Referenced
Publications
Technical Manuals Online! - http://www.tech-man.com

this is blank text
Technical Manuals Online! - http://www.tech-man.com

v
Cautions and Warnings................................................................................. i
Codes and Standards....................................................................................ii
Factory Mutual Approved............................................................................ii
Local Approvals...........................................................................................ii
NFPA Referenced Publications...................................................................iii
Table of Contents............................................................................................. v
Chapter 1. System Overview
Introduction...............................................................................................1-1
Related Documents...................................................................................1-2
Description................................................................................................1-2
Chapter 2. Basic Programming
Introduction...............................................................................................2-1
Menu Structure..........................................................................................2-1
Basic Things to Know About Programming a 4005......................................2-2
Storing and Saving Editing Changes.........................................................2-2
Programming Keys....................................................................................2-2
Programming Mode ..................................................................................2-3
LogIn.........................................................................................................2-3
Default Passcodes .....................................................................................2-3
Logout.......................................................................................................2-4
Operations Involving Points: Viewing Points...............................................2-5
Viewing Points..........................................................................................2-5
Function Control.......................................................................................2-6
Enabling a Point........................................................................................2-7
Disabling a Point.......................................................................................2-8
Editing a Point Label ................................................................................2-9
Clearing a Point Label.............................................................................2-11
Editing Point Types.................................................................................2-12
Edit Mode Programming.............................................................................2-13
Edit Mode Programming.........................................................................2-13
Operations Involving Cards: Adding an Input/Output (I/O) Card...............2-15
Adding an Input/Output (I/O) Card.........................................................2-15
Deleting Input/Output Cards...................................................................2-17
Modifying Input/Output Card Devices....................................................2-18
Adding a Remote Unit Interface (RUI) Card..........................................2-20
Deleting a Remote Unit Interface (RUI) Card ........................................2-21
Operations Involving System Options: Changing Time/Date Format.........2-22
Changing Time/Date Format...................................................................2-22
Turning the Active Point Reminder ON or OFF.....................................2-23
Setting the Silence/Reset Inhibit Timer...................................................2-24
Table of Contents
Technical Manuals Online! - http://www.tech-man.com

vi
Setting the Cut-Out Timer.......................................................................2-25
Setting the Door Drop Alarm..................................................................2-26
Setting the Door Drop AC Loss Timer ...................................................2-27
Setting the Audible Evacuation Signal....................................................2-28
Setting the Visible Evacuation Signal.....................................................2-29
Enabling City Circuit 1 and/or City Circuit 2..........................................2-30
Enabling or Disabling the Expansion Power Supply Circuit
Supervision .............................................................................................2-31
Saving Editing Changes..............................................................................2-32
Overview.................................................................................................2-32
Saving Changes at the End of an Editing Session...................................2-32
Saving Changes Anytime During Programming .....................................2-33
Canceling Editing Changes.........................................................................2-34
Overview.................................................................................................2-34
Abandoning Changes at the End of an Editing Session...........................2-34
Canceling Changes Anytime During Programming ................................2-35
Performing Basic Operations: Changing Access Level...............................2-36
Changing Access Level...........................................................................2-36
Default Passcodes ...................................................................................2-37
Changing Passcodes................................................................................2-38
Setting the Time and Date...........................................................................2-39
Setting the Time and Date.......................................................................2-39
Executing a Cold Start ............................................................................2-41
Operations Involving Lists: User Pseudo Points.........................................2-43
User Pseudo Points .................................................................................2-43
Adding Points to a List............................................................................2-44
Chapter 3. Custom Control
Introduction...............................................................................................3-1
Custom Control Overview ........................................................................3-1
To Start Custom Control Programming ....................................................3-2
Custom Control Menu Navigation............................................................3-2
Equation Level..........................................................................................3-3
Custom Control Level...............................................................................3-4
Equations ..................................................................................................3-4
Input Side (IF)...........................................................................................3-4
Input Field 1..................................................................................................3-5
Input Field 1..............................................................................................3-5
The AND Link Operator...........................................................................3-5
The OR Link operator...............................................................................3-6
Using the AND Operator first and the OR Operator second.....................3-7
Using the OR Operator first and the AND Operator second.....................3-8
Input Field 2..................................................................................................3-9
Overview...................................................................................................3-9
Using the AND and NOT Operators.........................................................3-9
Using the OR and NOT Operators..........................................................3-10
Technical Manuals Online! - http://www.tech-man.com

vii
Input Field 3 and Input Field 4....................................................................3-11
Overview.................................................................................................3-11
Using the FIRE Qualifier........................................................................3-11
Using the FIRE DET Qualifier ...............................................................3-12
Using the FIRE ACK Qualifier...............................................................3-13
Using the SUPV Qualifier.......................................................................3-13
Using the SUPV ACK Qualifier .............................................................3-14
Using the TBL Qualifier .........................................................................3-14
Using the TBL ACK Qualifier................................................................3-15
Using the ON/CODE and OFF Qualifiers...............................................3-15
Second Stage Fields....................................................................................3-17
The COMP CNST, ANY, ALL, and DELAY CNST Qualifiers.............3-17
Using the COMP CNST Qualifier ..........................................................3-17
Using the ANY Qualifier ........................................................................3-18
Using the ALL Qualifier.........................................................................3-18
Using the DELAY CNST Qualifier ........................................................3-19
Output Statements.......................................................................................3-20
Output Side (THEN)...............................................................................3-20
Output Field 1.........................................................................................3-20
Output Field 2.........................................................................................3-20
Output Field 3.........................................................................................3-21
Chapter 4. Common Simplex Multi-Functional
Programming Language (SMPL) Applications
Introduction...............................................................................................4-1
Selective Signals by Floor.........................................................................4-1
Selective Signals by Zone.........................................................................4-3
Selective Signal Operation for Fire Floor, Floor Above,
and Floor Below........................................................................................4-4
Selective Relay Control for Fan/Damper Operation.................................4-5
Selective Bypass of NAC/Relay Circuits..................................................4-8
Pre-Signal Operation.................................................................................4-9
Cross-Zoning Function............................................................................4-10
Non-Latching / Non-Alarm Point Operation...........................................4-10
AC Power Failure Operation...................................................................4-11
Delay Door Drop on AC Power Failure Operation.................................4-11
SCU/RCU Point Matrix (Zone Grouping) ..............................................4-12
Stagger/Start Operation...........................................................................4-13
Elevator Recall Operation.......................................................................4-14
Chapter 5. Point Type Charts
Introduction...............................................................................................5-1
Displaying information on the LCD Panel................................................5-1
Point Type Messages for Monitor Points......................................................5-3
Monitor Points ..........................................................................................5-3
Point Type Messages for Signal Points.......................................................5-13
Signal Points...........................................................................................5-13
Technical Manuals Online! - http://www.tech-man.com

viii
Point Type Messages for Auxiliary Relay Points........................................5-20
Auxiliary Relay Points............................................................................5-20
Pseudo Point Types.....................................................................................5-26
Digital Pseudo Points..............................................................................5-26
Analog Pseudo Points .............................................................................5-26
Chapter 6. Programming Guides and
Reference Information
Introduction...............................................................................................6-1
System Programming Worksheet..............................................................6-1
4005 Module Identification and Placement Chart.....................................6-2
Front Panel Programming.............................................................................6-3
Menu Structure..........................................................................................6-3
Edit Point..................................................................................................6-3
Edit Cards .................................................................................................6-4
SMPL Programming.....................................................................................6-5
Edit SMPL ................................................................................................6-5
Sample Program........................................................................................6-5
Valid Operator Codes and Parameter Tables............................................6-5
SMPL Equations.......................................................................................6-6
System Options...........................................................................................6-10
System Option Chart...............................................................................6-10
Edit Access Levels..................................................................................6-10
Edit Passcodes.........................................................................................6-10
Restore CFIG (Clear Edit Buffer)...........................................................6-10
Save to CFIG ..........................................................................................6-10
Initiating Device Circuit (IDC) Zones.........................................................6-11
Recording your System’s IDC Zones......................................................6-11
Monitor Point and Signal Point Types........................................................6-12
Monitor Point Types...............................................................................6-12
Signal Point Types..................................................................................6-12
NAC/Relay Circuits....................................................................................6-13
Recording your System’s NAC/Relay Points..........................................6-13
Relay Point Types...................................................................................6-13
Custom Labeling.........................................................................................6-14
Recording your System’s Custom Labels................................................6-14
Reference Information ................................................................................6-15
CPU Card................................................................................................6-15
RCU/SCU Addresses..............................................................................6-16
Input/Output Card Addresses..................................................................6-17
Power Supply Card.................................................................................6-18
Digital Pseudo Card................................................................................6-19
Analog Pseudo Card ...............................................................................6-20
List Pseudo Card.....................................................................................6-20
Technical Manuals Online! - http://www.tech-man.com

1-1
This publication shows how to use the menu-driven Front Panel Programming
feature of the 4005 Fire Alarm. All control of the 4005 is allowed through the
front panel via menus and the keypad.
Note: When a membrane panel key is referenced in this manual, it is
normally shown between angle brackets. Examples are
<Menu> and <System Reset>.
Chapter 2 shows the basic programming involved with factory-configured
operation of the 4005. The 4005 base panel is configured (and shipped) as a
general alarm system. A number of menu selectable options are provided to
further enhance the 4005 operation.
The 4005 has resident editing capability. Once the programming mode is
selected, the 4005’s LCD display and keypad become the indicator and controls
of the resident editor (programmer).
Chapter 3 shows how to use the Simplex Multi-functional Programming
Language (SMPL) to program custom functions into the 4005 when more
sophisticated operations are required. The SMPL option can be used to
customize the operation of an Output, while the rest of the system continues to
operate as a general alarm system. The SMPL programming provides many
more features and applications which are discussed in this manual.
Chapter 4 contains a number of SMPL applications with examples of equations
used for various control and signaling functions.
Chapter 5 contains Point Type Charts which list exact LCD displays and system
status corresponding to each type of Point in the 4005 system.
Chapter 6 contains Programming Guides and Reference Information to assist you
in planning and documenting the programming steps you take. This chapter also
provides information about System Addresses, Point and Device Types, and
Point descriptions.
Important: The 4005 system continues to operate as a fire alarm
system during programming operations
Continued on next page
Chapter 1
System Overview
Introduction
Technical Manuals Online! - http://www.tech-man.com

1-2
The following manuals contain information about the 4005:
Publication Title Part #
4005 Fire Alarm Installation/Operating Instructions
Rev. A
574-068
4005 Operating Instructions Following an
Alarm/Supervisory/Trouble Condition ... Ed 8 95 574-069
4005 Fire Alarm I/O Cards – Installation Instructions
Ed 3 96 574-070
4005 Fire Alarm City Circuit Card – Installation
Instructions . .. Rev. B 574-071
4005 Fire Alarm Expansion Power Supply & Power
Distribution Boards – Installation Instructions . .. Rev. A 574-072
4005 Fire Alarm PC Interface Operating Instructions
Rev. A
574-328
4005 Fire Alarm Programming Sheets FA4-41-655
4005 Fire Alarm Pocket Training Reference FA4-91-654
The 4005 is a microprocessor-based, battery-backed, electrically-supervised fire
alarm system capable of supporting from 8 to 40 circuits. These circuits, either
initiating device circuits (IDC) or notification appliance circuits (NAC), are
added to the system in blocks of four. In addition, the 4005 can automatically
control supplementary equipment such as fire doors and fans during a fire
condition using NACs converted to auxiliary relay outputs.
The 4005 provides audible and visible indications during trouble, supervisory, or
alarm (fire) conditions. Should any of these conditions occur, the system
activates the applicable notification appliance(s), LEDs, and the panel tone-alert.
The indications continue until someone appropriately acknowledges the
condition.
System Overview, Continued
Related Documents
Description
Technical Manuals Online! - http://www.tech-man.com

2-1
This chapter discusses the basic programming functions that are available with
the 4005 Fire Alarm Control Panel (FACP). The programming of more advanced
functions is discussed in Chapter 3.
All programming is done from the front panel via menu-driven prompts. Access
levels protect different programming options. All programming described in this
publication assumes a Level 4 (Simplex Service Mode) access. Figure 2-1
illustrates the entire menu structure at Level 4 operation.
Figure 2-1. Level 4 Menu Structure
Continued on next page
Chapter 2
Basic Programming
Introduction
Menu Structure
View
Points
View
Points
Monitor
Monitor
Relay
Relay
Signal
Signal
Digital
Digital
Analog
Analog
List
List
Generic
Input
Generic
Input
Generic
Output
Generic
Output
System
Points
System
Points
History
Log
History
Log
AlarmLog
AlarmLog
TroubleLog
TroubleLog
Combine
Log
Combine
Log
Software
Revision
Software
Revision Set
Time/Date
Set
Time/Date
Passcode
Passcode
LogIn/Out
LogIn/Out
Walk
Test
Walk
Test
Off
Off
Log
Log
Signal
Signal
Cold
Start
Cold
Start Programming
Programming
Edit Point
Edit Point
Relay
Relay
Signal
Signal
Digital
Digital
Analog
Analog
List
List
Generic
Input
Generic
Input
Edit Card
Edit Card System Options System Options
Time/Date
Format
Time/Date
Format
ActivePoint
Reminder
ActivePoint
Reminder
Edit SMPL
Edit SMPL
SaveCFIG
SaveCFIG
Restore
CFIG
Restore
CFIG
Generic
Output
Generic
Output
Monitor
Monitor
DeleteI/O
Card
DeleteI/O
Card
ModifyI/O
Card
ModifyI/O
Card
AddRUI
Card
AddRUI
Card
Delete RUI
Card
Delete RUI
Card
AddI/O
Card
AddI/O
Card
Doorholder AC
Fail Drop Time
Doorholder AC
Fail Drop Time
Silence / Reset
Inhibit
Silence / Reset
Inhibit
Signal Operation
(Visible, Audible,
Evacuation)
Signal Operation
(Visible, Audible,
Evacuation)
Signal Cut-out
Time
Signal Cut-out
Time
Enable City
Circuit 1
Enable City
Circuit 1
Enable City
Circuit 2
Enable City
Circuit 2
Expansion Power
Supply
Expansion Power
Supply
Doorholder Alarm
Drop Timer
Doorholder Alarm
Drop Timer Access
Level
Access
Level
Passcode
Passcode
Main Menu
activated from
MENUKey
Main Menu
activated from
MENUKey
FunctionMenu
activated from
FUNC Key
FunctionMenu
activated from
FUNC Key
City Circuit
Disconnect
City Circuit
Disconnect
DoorHolder
Bypass
DoorHolder
Bypass
Control Point
Bypass
Control Point
Bypass
Elevator
Bypass
Elevator
Bypass
Manual
Evacuation
Manual
Evacuation
LampTest
LampTest
TOP LEVEL
TOP LEVEL
High Level
StatusScreen
High Level
StatusScreen
Edit
Mode
Edit
Mode
Technical Manuals Online! - http://www.tech-man.com

2-2
During a programming session, the edit changes are stored in a temporary
memory area called the Edit Buffer. This means that you can leave the
programming session and perform other operations on the 4005.
As a result of this flexibility, the edit session becomes a two-step operation:
1. Editing and
2. Saving the changes to CFIG.
After the edit session is complete, you must select the “Save to CFIG”option in
order to save the edit changes (see the Save to CFIG in Chapter 6 of this
publication). There are two programming reminder screens that notify you to act
on changes in the Edit Buffer. Additionally, if there are no key presses within 10
minutes, the system returns to the High-Level Status screen at access level 1.
During programming mode, only certain keys remain active. When in the
programming mode, the 4005 still functions as a fire alarm system. If an alarm
should sound, use the <Exit/Clear> key to exit the programming mode (by
pressing the key several times). Once at the High-Level Status Screen (the
display shows the first alarm or a normal status) alarms, supervisories, or
troubles can be acknowledged and/or viewed for additional information.
Figure 2-2 illustrates the front panel of the 4005 with a High-Level Status screen
displaying normal system operation.
Refer to the 4005 Fire Alarm
 Installation/Operating Instructions (Pub. No.
FA4-21-650) for more information on the operator keys.
Figure 2-2. 4005 Front Panel
Continued on next page
Basic Things to Know About Programming a 4005
Storing and Saving Editing
Changes
Programming Keys
6<67(0,61250$/

S
P 

0RQ$XJ
FIRE
ALARM
SYSTEM
SUPERVISORY
SYSTEM
TROUBLE
ALARM
SILENCED
AC
POWER
ALARM
ACK
SUPV
ACK TROUBLE ACK ALARM SILENCE SYSTEM RESET
Menu Function Disable
Enable Exit
Clear Enter Previous Next
LCD
LEDs
Operator Keys
Menu Navigation Keys
(Become Programming
Keys in Programming
Mode)
Technical Manuals Online! - http://www.tech-man.com

2-3
Even though “Passcode”is not the first menu option, you must log in to the 4005
FACP in order to perform the Level 4 programming covered in the remainder of
this publication.
To enter the Programming mode, press <Menu>. (You must always press
<Menu> first to begin programming mode.)
The Menu Programming screen is displayed.
Use the following steps and Figures 2-3 and 2-4 to log in to the 4005.
Note: All passcodes consist of a four-digit number (refer to Default
Passcodes below). An asterisk (∗) appears in the place of an
entered number for security purposes.
A.
B.
C.
D.
Figure 2-3. Menu Progression from the Normal Menu to the
Passcode Menu
1. Press <Next> to scroll through the menus until [3DVVFRGH] is displayed
(A) and then press <Enter> (B).
2. Press <Enter> to Login (C).
3. Press <Next> to scroll through the numbers (0-9) for the first digit of the
passcode. When the correct number appears between the focus brackets
( [ ] ), press <ö> to move the brackets to the next digit of the code.
4. Repeat Step 3 until all four numbers are entered (D).
The 4005 comes with three default passcodes.
•2000 = Level 2 access
•3000 = Level 3 access
•4000 = Level 4 access (causes a Simplex Service Mode Trouble)
Continued on next page
Basic Things to Know About Programming a 4005, Continued
Programming Mode
LogIn
Default Passcodes
6<67(0,61250$/
0HQX >3 VVFRGH@
&XUUHQW$FFHVV/HYHO /HYHO
3 VVFRGH >/RJLQ@
&XUUHQW$FFHVV/HYHO /HYHO
3 VVFRGH >@
&XUUHQW$FFHVV/HYHO /HYHO
3 VVFRGH >@
Technical Manuals Online! - http://www.tech-man.com

2-4
E.
F.
G.
Figure 2-4. Menu Progression from the Login Accepted Menu to the
Fire, Supervisory, Trouble Menu
5. Press <Enter> to accept the passcode. (Logging in at Level 4 causes a
Simplex Service Mode Trouble. Acknowledge the trouble and continue.)
The display in (E) appears briefly and then (F) appears after the Simplex
Service Mode trouble is acknowledged.
6. Press <Menu> to start Programming (G).
Follow Steps 1 and 2 to log out of the 4005.
1. Press <Next> to scroll through the menus until [3DVVFRGH] is displayed
and then press <Enter>.
2. Press <Next> until [/RJ2XW] is displayed and then press Enter.
The 4005 defaults to Level 1 access.
Basic Things to Know About Programming a 4005, Continued
Default Passcodes (Continued)
Logout
/RJLQLV$FFHSWHG
&XUUHQW$FFHVV/HYHO /HYHO
6LPSOH[6HUYLFH0RGH
7URXEOH3RLQW 7URXEOH 
),5(  683(59,625< 7528%/( 
0HQX >9LHZ3RLQWV@
Technical Manuals Online! - http://www.tech-man.com

2-5
To View a Point, use the following steps:
1. To view points, press <Menu>, <Next> until [9LHZ3RLQWV] is
displayed, and then press <Enter>.
2. Press <Previous> or <Next> to display the Device Type of the point you
wish to view and then press <Enter> (refer to Table 2-1).
The first point for that Device Type is displayed.
Table 2-1. Device Type
Device Type
Monitor
Relay
Signal
Digital
Analog
Generic Output
Generic Input
System Points
List
3. Press <Next> or <Previous> to scroll through additional points.
Figure 2-5. Standard Screens Based on Device Type
4. To view additional information (if available), press <ö> or <ì> to
advance through the information screens. Pressing <Exit/Clear> returns
you to the menu screen (see Gin Figure 2-4). When viewing the point or
list, all points or lists have two standard screens based on the device type
(see Figure 2-5).
Operations Involving Points:
Viewing Points
Viewing Points
&O VV)LUH0RQLWRU =21(
0RQLWRU=RQH 1250$/ 
'HYLFH 021% & UG  3RLQW 
0RQLWRU=RQH  1RUP O
Technical Manuals Online! - http://www.tech-man.com

2-6
Certain Functions are allowed during the View Points session. To activate
Function Control for a specific point, use Steps 1 through 3 above to view the
point and then press <Function>. Refer to Table 2-2 for a list of functions based
on device types.
Table 2-2. Functions Based On Device Type
Device Type Available Function Commands
Monitor Clear Verification Tally
Relay
Signal
Digital (P27-P50)
• Turn ON the point
• Turn OFF the point
• Turn the point to AUTO
• Change the point Priority
Analog (A5-A25) Change the Point Value
System Points Turn ON/OFF certain points
Lists
• Turn List ON
• Turn List OFF
• Turn List Auto
Generic Outputs • Turn ON the point
• Turn OFF the point
Use <Previous> or <Next> to scroll through the commands and then press
<Enter> to execute the command.
Function Control while Viewing Points
Function Control
Technical Manuals Online! - http://www.tech-man.com

2-7
To Enable a Point, use Figure 2-6 and the following steps:
1. View points by pressing <Menu> and <Next> until [9LHZ3RLQWV] is
displayed, and then press <Enter>.
2. Press <Previous> or <Next> to display the Device Type of the point you
wish to enable and then press <Enter>.
The first point for that Device Type is displayed.
3. Press <Previous> or <Next> to display the point you wish to enable (A).
A.
B.
C.
D.
Figure 2-6. Typical Screens Used to Enable a Point
4. Press <Enable/Disable>. Press <Previous> or <Next> until [(QDEOH] is
displayed (B).
5. Press <Enter> to enable the point.
6. Press <Enter> to confirm your choice (C).
The point enables in 30 seconds (D). Press <Exit/Clear> to stop the point
from enabling during this time period.
Enabling a Point
Enabling a Point
)LUVW)ORRU( VW:LQJ 5RRP
0RQLWRU=RQH 7528%/( 
)LUVW)ORRU( VW:LQJ 5RRP
&RQWURO >(Q EOH@ 6W WXV ',6$%/('
)LUVW)ORRU( VW:LQJ 5RRP
3UHVV(17(5WR(Q EOH(;,7WRF QFHO
)LUVW)ORRU( VW:LQJ 5RRP
3RLQWZLOO(1$%/(LQ(;,7WRF QFH
O
Technical Manuals Online! - http://www.tech-man.com

2-8
To Disable a Point, use the following steps:
1. View points by pressing <Menu> and <Next> until [9LHZ3RLQWV] is
displayed, and then press <Enter>.
2. Press <Previous> or <Next> to display the Device Type of the point you
wish to disable and then press <Enter>.
The first point for that Device Type is displayed.
3. Press <Previous> or <Next> to display the point you wish to enable (A).
A.
B.
C.
D.
Figure 2-7. Typical Screens Used to Disable a Point
4. Press <Enable/Disable>. Press <Previous> or <Next> until ['LVDEOH] is
displayed (B).
5. Press <Enter> to disable the point.
6. Press <Enter> to confirm your choice or <Exit/Clear> to cancel (C).
The point disables immediately and a trouble occurs (D). Acknowledge the
trouble and continue.
Disabling a Point
Disabling a Point
)LUVW)ORRU( VW:LQJ 5RRP
0RQLWRU=RQH 7528%/( 
)LUVW)ORRU( VW:LQJ 5RRP
&RQWURO >'LV EOH@ 6W WXV (1$%/('
)LUVW)ORRU( VW:LQJ 5RRP
3UHVV(17(5WR'LV EOH(;,7WRF QFHO
)LUVW)ORRU( VW:LQJ 5RRP
0RQLWRU=RQH 7528%/( 
Technical Manuals Online! - http://www.tech-man.com