Simplex MINIPLEX 4100-9600 User manual

Features
4100U Series MINIPLEX transponders allow
remotely located initiating and notification
functions:
x Transponder operation is available as standard or with
local mode operation
x Communications with the host fire alarm control panel
use the Remote Unit Interface (RUI) format
Initiating functions include:
x Conventional initiating device circuit (IDC) support
x Addressable device support including TrueAlarm®
analog sensor compatibility**
Notification functions include:
x Conventional DC notification appliance circuits
x Emergency voice/alarm communications
x TrueAlert®addressable strobe and horn notification
Local mode operation provides:
x Default local initiating and notification operation in the
event of a communications loss with the host control panel
x Enabling of an optional Local Mode Controller with a
local alarm sounder, LED status indicators, and
keyswitch enabled control switches
x Support for IDNet™ addressable devices, conventional
and TrueAlert addressable notification appliances, and
default output tones from local amplifiers**
Optional modules include:
x Digital or Analog audio riser modules for connection to
system audio signals
x Digital or analog input audio amplifiers with integral
on-board NACs
x Power supplies with or without battery chargers
x City Connect modules and RS-232 ports for printers or
maintenance terminals
x Alarm relays, auxiliary relays, additional IDC modules,
and NAC expansion modules
Cabinets are equipped with solid doors (beige or
red) and in two or three bay sizes
Listed to:
x UL Std. 864, Fire Detection and Control (UOJZ), and
Smoke Control Service (UUKL)
x UL Std. 2017, Process Management Equipment (QVAX)
x UL Std. 1076, Proprietary Alarm Units-Burglar (APOU)
x UL Std. 1730, Smoke Detector Monitor (UULH)
x ULC Std. S527-99
* See pages 4 and 5 for product that is listed as UL or ULC. This product has been approved by
the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health
and Safety Code. See CSFM Listing 7165-0026:251 (non-high rise) and 7170-0026:250 (high
rise) for allowable values and/or conditions concerning material presented in this document. It
is subject to re-examination, revision, and possible cancellation. Accepted for use – City of
New York Department of Buildings – MEA35-93E. Additional listings may be applicable;
contact your local Simplex product supplier for the latest status. Listings and approvals under
Simplex Time Recorder Co. are the property of Tyco Safety Products Westminster.
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
PressACKlocatedunderflashingindicator.
Repeatoperationuntilalleventsareacknowledged.
Localto ne w ill silen ce.
ABC
ACPower
DEF GHI
JKL MNO PQR
'SP'() ,0:
STU VWX YZ/
ALARMS
Fire Al arm Priority 2 A la rm
SYSTEMWA RNING S
Supervisory Trouble AlarmSilenced
EmergencyOperatingInstructions
Alarmor Warning Cond it io n
Howto Acknow le dg e /V i ew Event s
HowtoS ilence Building Sig nals
Systemindicatorflashing.ToneOn. PressAlarmSilence.
HowtoRe set System
PressSystemReset.
PressAcktosilencetonedevice.
ZONE
1
SIG
2
AUX
3
FB
4
IO
5
IDNet
6
P
7
A
8
L
9
NET ADDR
0DEL
Enter C/Exit
Fire A l ar m
Ack
Priority2
Ack
Supv
Ack
Trouble
Ack
Alarm
Silence
System
Reset
Event
Time
Enable On
Arm
Disable Off
Disarm Auto Lamp Test
More
Info
Menu
Previous
Next
SYSTEMIS NORMAL
08:23:43am MON11-DEC-00
Fire Control
4100U Fire Alarm Control Panel
with Voice Control
ALARMFIRE
PULL DOWN
C
A
U
T
I
O
N
C
A
U
T
I
O
N
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
Addressable devices
Audio NAC
FireAlarm Local Mode Controller
ENABLE
CONTROL
Alarm
Alarm
Silenced
Local
Mode
Active
Power
On
Alarm
Silence Reset
Local
Mode
Control
Local mode
controller
Strobe NAC
MINIPLEX transponder
Typical 4100U MINIPLEX System One-Line Drawing
Introduction
4100U MINIPLEX transponders connect to a host
4100U Fire Alarm Control Panel using Simplex®remote
unit interface (RUI) communications. At the transponder,
RUI communications are received by the transponder
interface module and translated into the same internal
communications format that is used in the host control
panel.
Remotely located modules. With RUI
communications, the transponder can remotely provide
the same initiating and notification functions that occur at
the host control panel without requiring multiple long
distance wiring runs. Connections to the host panel are
low current communications and audio wiring with
distances up to 2500 ft (762 m).
Software Revisions. Some of the features detailed and
products listed in this document require 4100U System
Software Revision 11.08 or higher. For pre-11.08 system
expansion options, hardware updates may be required.
Contact your local Simplex®product supplier for details.
** Simplex fire alarm technology is protected by the following U.S. Patent Numbers:
TrueAlarm analog smoke detection: 5,155,468; 5,173,683 and 5,543,777. IDNet and
MAPNET II addressable communications; 4,796,025. TrueAlert addressable notification;
6,313,744 and 6,426,697. SmartSync horn/strobe control; 6,281,789. Flex-35 and Flex-50
amplifier operation; 6,452,491.
Fire Control Panels
UL, ULC Listed; FM, CSFM, Addressable Fire Detection and Control
and MEA (NYC) Approved* MINIPLEX®Transponders
S4100-0035-6 4/2005

Introduction (Continued)
Please refer to document S4100-0031 and the other
documents listed on page 3 for additional information
concerning the extensive initiating and notification
features of the 4100U fire alarm control panels.
Module Bay Description
Transponder model 4100-9600 includes a bay
assembly, a power distribution interface module (PDI), a
Basic Transponder Interface Module, and an interconnect
harness. Communications with the host fire alarm control
panel are via a Remote Unit Interface (RUI) connection
that allows for up to 2500 ft (762 m) distance. RUI can
communicate with up to a total of 31 remote devices and
can be either Style 4 or Style 7 communications.
Transponder model 4100-9601 substitutes a Local
Mode Transponder Module for the Basic Transponder
Module.
Optional Expansion Bays each include a PDI and
accept a variety of optional modules (refer to list starting
on page 4).
The Battery Compartment (bottom) accepts two
batteries, up to 50 Ah, that can be mounted within the
cabinet. Battery mounting does not interfere with
available module space. A power supply with battery
charger is required for each battery set.
Packaging Availability
x Modules are power-limited (except as noted, such as
relay modules)
x Enclosure are available for either two or three bay
sizes or for cabinet rack mounting
x Boxes and solid doors are available in beige or red
(ordered separately)
x Up to eight close-nippled cabinets can be connected at
one transponder location (close-nippled is mounted
within 20 ft (6 m) and with interconnecting wiring
enclosed in conduit)
x Refer to document S4100-0037 for enclosure details
Local Mode Control Operation
Default Stand-Alone Operation. In the event of a
communications loss with the host fire alarm control
panel, model 4100-9601 MINIPLEX Local Mode
Transponders provide fire alarm response default
operation for its connected devices and appliances per the
following.
Input Operation. During local mode operation,
TrueAlarm initiating devices connected to the transponder
will cause an alarm at their least sensitive alarm threshold.
x Photoelectric sensors will alarm at 3.7%/ft smoke
obscuration
x Ionization sensors will alarm at 1.3%/ft obscuration
x Heat sensors will alarm at a fixed temperature of 135° F
(57° C)
x TrueAlarm device LEDs will be activated to indicate a
device in alarm
Local Mode Control Operation (Continued)
Notification Operation. Fire alarm conditions reported
against a fire alarm point type within a transponder in
local mode will cause all notification appliance circuits in
that transponder to:
x Sound a general alarm temporal pattern horn tone
x Activate visible notification appliance circuits
Local Mode Module Support. Local mode operation
provides support for the following 4100U modules:
x System Power Supplies (SPS), Expansion Power
Supplies (XPS), and Remote Power Supplies (RPS),
including on-board notification appliance circuits
(NACs) and expansion signal modules, operated at a
temporal pattern,
x TrueAlert Power Supplies (TPS) including the on-board
signaling line circuits (SLCs)
x IDNet addressable device circuits, including those
on-board the SPS, IDNet expansion modules, and the
quad isolator when used for IDNet communications
x 4100U amplifiers will provide their on-board horn tones
(500 Hz) at a temporal pattern through their on-board
amplifier NACs
Local Mode Operation Module Exclusion. Modules
not listed above but that are listed as compatible with
MINIPLEX transponders per this document, do not
interfere with local mode operation but are not supported
during local mode operation.
Local Mode Controller
Operation. During local mode operation, an optional
Local Mode Controller will indicate status (see illustration
below) and can be enabled using a keyswitch to perform
local alarm silence or reset. If alarms occurring during local
mode are reset using a Local Mode Controller, upon
restoration of communications, those alarms will not be
sent to the master controller. If alarms are still present
upon restoration of communications, then the alarm
condition will be reported and host fire alarm control panel
programmed alarm functions will occur. When
communications are re-established, the local mode
transponder restores automatically.
Mounting. Local Mode Controllers are mounted on
three-gang plates, are available in beige or red, and for
either flush or semi-flush mounting. (See page 7 for
details).
Fire Alarm Local Mode Controller
ENABLE
CONTROL
Alarm
Alarm
Silenced
Local
Mode
Active
Power
On
Alarm
Silence Reset
Local
Mode
Control
See Operating Instruction 579-343
Local Mode Controller Module
2 S4100-0035-6 4/2005

3 S4100-0035-6 4/2005
ALARMFIRE
PULL DOWN
ALARMFIRE
PULL DOWN
ALARMFIRE
PULL DOWN
ALARMFIRE
PULL DOWN
ALARMFIRE
PULL DOWN
ALARMFIRE
PULL DOWN
Second floor
Third floor
Fourth floor
Fifth floor
Sixth floor
Seventh floor
First floor
4100U Fire Alarm Control Panel
with Voice Control
MINIPLEX transponder
Speaker NAC
TrueAlarm sensors
and IDNet/MAPNET II
addressable circuits
Audio riser wiring,
twisted pair
RUI communications
wiring, twisted, shielded
pair
Legend:
ALARMFIRE
PULL DOWN
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
On
Off
Auto
PressACKl oc at ed underf la shing indic at or.
Repeatopera t ion until allev en ts are ack nowl edge d.
Localtone w ill sil ence.
ABC
ACPowe r
DEF G H I
JKL MN O PQ R
'SP'() ,0:
STU VWX Y Z /
ALARMS
FireAlar m Priority2Alarm
SYSTEMWARNINGS
Supervisory Trouble AlarmSilenced
EmergencyOperatingIn structions
Alarmor W arning Condit io n
HowtoAcknowledge/ViewEvents
HowtoSilence Building Signals
Systemindi c at or flashing. Tone On . Press Ala rm Sil ence.
Howto Reset Sy stem
PressSy st e m Res e t .
PressAck t o s i lence tone de v ic e.
ZONE
1
SIG
2
AUX
3
FB
4
IO
5
IDNet
6
P
7
A
8
L
9
NET AD DR
0DEL
Enter C/Exit
FireA l a rm
Ack
Priority2
Ack
Supv
Ack
Trouble
Ack
Alarm
Silence
System
Reset
Event
Time
Enable On
Arm
Disable Off
Disarm Auto Lamp Test
More
Info
Menu
Previous
Next
SYSTEM IS NORMAL
08:23:43am MON11-DEC-00
Fire Control
C
A
U
T
I
O
N
C
A
U
T
I
O
N
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
C
A
U
T
I
O
N
C
A
U
T
I
O
N
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
DISCONNECT
A.C.POWER
AND
BATTERY
BEFORE
SERVICING
MINIPLEX transponder
Strobe NAC
Subject Data Sheet Subject Data Sheet
Enclosures S4100-0037 Basic Panel Modules and Accessories S4100-0031
LED/Switch Modules S4100-0032 Network Display Unit (NDU) S4100-0036
4100U Audio/Phone Modules S4100-0034 Remote Annunciators S4100-0038
TrueAlert Addressable Products S4009-0003 Remote Battery Charger S4081-0002
IDNet+ Module with Quad Isolator S4100-0046
Typical Multi-Floor MINIPLEX Audio System
Additional 4100U Data Sheet Reference

4 S4100-0035-6 4/2005
Transponder Type
Model Description Supv. Alarm
4100-9600 Basic Transponder, includes bay equipment with power distribution interface, and 4100-0620
Basic Transponder Interface Module mounted in Block A 87 mA 87 mA
normal 87 mA 87 mA
4100-9601
Local Mode Transponder, includes bay equipment with power distribution
interface, and 4100-0625 Local Mode Transponder Interface Module mounted in
Block A in local mode 112 mA 112 mA
Local Mode Controller Selection (order as District P.O. from Space Age Electronics)
Model Description Supv. Alarm
4601-9108 Flush mount
4601-9109 Surface mount
Red with white
lettering normal 10 mA 10 mA
4601-9110 Flush mount
4601-9111 Surface mount
Beige with
black lettering
Local Mode Controller, 3-gang plate mounted;
flush mount requires a 1-1/2” (38 mm) deep
3-gang box; surface mount controllers include
a matching mounting box; refer to page 7 for
details in local mode 20 mA 60 mA
Communication Modules
Model Description Size Supv. Alarm
4100-6031 City Circuit, with disconnect switches 20 mA 36 mA
4100-6032 City Circuit, without disconnect switches
For use with SPS
only, not RPS 20 mA 36 mA
4100-6033
Select one per SPS
Alarm Relay, 3 Form C relays, 2 A @ 32 VDC; for SPS or RPS
Mounts
on SPS
or RPS 15 mA 37 mA
4100-6038 Dual RS-232 Interface 1 Slot 132 mA 132 mA
4100-6045 Decoder Module 3 Slots 85 mA 163 mA
4100-6048 VESDA®Aspiration System Interface 1 Slot 132 mA 132 mA
4100-9816 Master Clock Interface Module with one standard RS-232 port (see S4100-0033) 1 Slot 132 mA 132 mA
Expansion, System, Remote, and TrueAlert Power Supplies and Accessories
Model Voltage/Listing Description Size Supv. Alarm
4100-5101 120 VAC UL
4100-5103 120 VAC, Canadian ULC
4100-5102 220-240 VAC UL
Expansion Power Supply (XPS); 9 A output, 3
built-in Class A/B NACs; Canadian models have low
battery cutout*
2 Blocks 50 mA 50 mA
4100-5115 NAC Expansion Module, 3 NACs, Class A/B, mounts on XPS only N.A. 25 mA 25 mA
4100-5111 120 VAC UL
4100-5112 120 VAC, Canadian ULC
4100-5113 220-240 VAC UL
System Power Supply (SPS); 9 A power
supply/charger with 250 point IDNet channel, 3 Class
A/B NACs, and expansion slot for City Circuit or Alarm
Relay option; Canadian model has low battery cutout*
4 Blocks 175 mA 225 mA
4100-5125 120 VAC UL
4100-5126 120 VAC, Canadian ULC
4100-5127 220-240 VAC UL
Remote Power Supply (RPS); 9 A power
supply/charger similar to SPS except no IDNet
channel or City Circuits, will accept one 4100-6033;
Canadian model has low battery cutout*
4 Blocks 150 mA 185 mA
4100-5120 120 VAC UL
4100-5121 120 VAC, Canadian ULC
4100-5122 220-240 VAC UL
TrueAlert Power Supply (TPS); 3 built-in Class B
addressable Signaling Line Circuits (SLCs) rated 3 A
each, built-in battery charger, with 2 A auxiliary power
output tap; Canadian model has low battery cutout
4 Blocks 88 mA 100 mA
4100-5124 TrueAlert SLC Class A Adapter for all 3 SLCs, mounts on TPS only N.A. 7 mA 7 mA
4100-5152 12 VDC Power Option, 2 A maximum 1 Block 1.5 A maximum
4100-0636 Box Interconnection Harness Kit (non-audio); order one for each close-nippled cabinet
Miscellaneous Options and Accessories
Model Description
4100-1290 24 Point I/O Module for external connections, select each point as either a switch input (momentary or maintained) or
an output (for lamp/LED/relay); requires 1 Slot (refer to data sheet S4100-0032 for additional information)
4100-0632 Terminal Block Utility Module; provides 2, 16 position terminal blocks mounted on 4” x 5” single block size, capable of
up to 12 AWG wire (3.31 mm2)
4100-0633 Door Tamper Switch, connects into Transponder Interface Module, one per cabinet assembly if required
4100-0634 120 VAC
4100-0635 220/230/240 VAC Power Distribution Module (PDM) select per system voltage; one required per box
4100-9837 Green LED Power-on Indicator Kit, required for
ULC listing of MINIPLEX transponder Mounts using knockout provided in solid door
2081-9031 Series resistor for WSO, IDCs (N.O. water flow and tamper on same circuit, wires after water flow and before tamper)
470 , 1 W, encapsulated, two 18 AWG leads (0.82 mm2), 2-1/2” L x 1-3/8” W x 1” H (64 mm x 35 mm x 25 mm)
* Power supply NACs can provide synchronized strobe or SmartSync, two-wire operation. Continued on next page
MINIPLEX Transponder Product Selection

5 S4100-0035-6 4/2005
Audio Riser Modules
Model Description Size Supv. Alarm
4100-0621 Dual Channel Analog Audio Riser Module; accepts one or two separate audio signals from
host control panel; mounts in Block B, is controlled by Transponder Interface Module 1 Block 0 mA 0 mA
4100-0622 3-8 Channel Digital Audio Riser Module; similar to analog module, except receives and
decodes a digital input signal with up to eight audio channels; with Non-Alarm Audio input 1 Block 50 mA 50 mA
Analog Emergency Voice/Alarm Communications Equipment, Constant Supervision Compatible*
Model Description Details
4100-1361 25 VRMS output NAC rating = 1.4 A
4100-1362 70.07 VRMS output
Flex-35, 35 W Amplifier, constant
supervision compatible NAC rating = 0.5 A
35 W, or 100
speakers
4100-1312 25 VRMS output NAC rating = 2 A
4100-1313 70.7 VRMS output
Flex-50, 50 W Amplifier, constant
supervision compatible
Includes three on-board
Class B audio NACs;
power is supplied from
an XPS, RPS, or SPS NAC rating = 0.707 A
50 W, or 100
speakers
100 W Analog Amplifiers with Power Supply, Constant Supervision Compatible
Model/Output Voltage
25 VRMS 70.7 VRMS Power Supply Input/Listing Description Details
4100-1314 4100-1315 120 VAC, 60 Hz UL
4100-1316 4100-1317 120 VAC, 60 Hz ULC
4100-1318 4100-1319 220/230/240 VAC, 50/60 Hz UL
Primary
100 W
Amplifier
Includes six, Class B audio NACs;
NAC rating = 50 W or 100 speakers
maximum; 2 A @ 25 VRMS;
1.4 A @ 70.7 VRMS
4100-1320 4100-1321 120 VAC, 60 Hz UL
4100-1322 4100-1323 120 VAC, 60 Hz ULC
4100-1324 4100-1325 220/230/240 VAC, 50/60 Hz UL
Backup
100 W
Amplifier
Uses the six Class B NACs of primary
amplifier
ULC
models
have low
battery
dropout
circuit
Digital Emergency Voice/Alarm Communications Equipment*
Model Description Details
4100-1363 25 VRMS output NAC rating = 1.4 A
4100-1364 70.07 VRMS output
Flex-35, 35 W Amplifier, constant
supervision compatible NAC rating = 0.5 A
35 W, or 100
speakers
4100-1326 25 VRMS output NAC rating = 2 A
4100-1327 70.7 VRMS output
Flex-50, 50 W Amplifier, constant
supervision compatible
Includes three on-board
Class B audio NACs;
power is supplied from
an XPS, RPS, or SPS NAC rating = 0.707 A
50 W, or 100
speakers
100 W Digital Amplifiers with Power Supply, Constant Supervision Compatible
Model/Output Voltage
25 VRMS 70.7 VRMS Power Supply Input/Listing Description Details
4100-1328 4100-1329 120 VAC, 60 Hz UL
4100-1330 4100-1331 120 VAC, 60 Hz ULC
4100-1332 4100-1333 220/230/240 VAC, 50/60 Hz UL
Primary
100 W
Amplifier
Includes six, Class B audio NACs;
NAC rating = 50 W or 100 speakers
maximum; 2 A @ 25 VRMS;
1.4 A @ 70.7 VRMS
4100-1334 4100-1335 120 VAC, 60 Hz UL
4100-1336 4100-1337 120 VAC, 60 Hz ULC
4100-1338 4100-1339 220/230/240 VAC, 50/60 Hz UL
Backup
100 W
Amplifier
Uses the six Class B NACs of primary
amplifier
ULC
models
have low
battery
dropout
circuit
Options for use with either Analog or Digital Amplifiers
Model Description Details and Mounting Reference
4100-1245 Flex-35/50 Expansion NAC Module; adds three
Class B audio NACs
Mounts on Flex-35/50 assembly; NAC ratings = 1.5 A, 35/50 W,
or 100 speakers maximum; Supv = 0.6 mA, Alarm = 60 mA
4100-1246 Flex-35/50 Class A Adapter Module; converts
three on-board NACS to Class A operation
Choose
one per
amplifier Mounts on Flex-35/50 assembly; NAC ratings = 2 A, 50 W, or
100 speakers maximum; Supv = 0, Alarm = 30 mA
4100-1248 100 W Amplifier Expansion NAC Module; NAC
ratings = 1.5 A, 50 W, or 100 speakers max.
Provides six additional Class B audio NACs, mounts on 100 W
amplifier assembly; Supv = 1.2 mA, Alarm = 120 mA
4100-1249 100 W Class A Adapter Module; NAC ratings =
2 A, 50 W, or 100 speakers max.
Choose
one per
amplifier Converts six on-board NACs to Class A operation, mounts on
100 W amplifier assembly; Supv = 0, Alarm = 60 mA
4100-1259
25 VRMS Output; NAC
rating = 2 A, 50 W, or 100
speakers max.
Supv = 10 mA
Alarm = 35 mA
4100-1260
70.7 VRMS Output; NAC
rating = 0.707 A, 50 W, or
100 speakers max.
Constant Supervision
Adapter for three NACs;
select per amplifier output
(not compatible with amplifier
NAC expansion modules) Supv = 38 mA
Alarm = 60 mA
Converts three Class B audio NACS to
Class A or Class B Constant Supervision
NACs; mounts on Flex-35/50 or 100 W
amplifier assembly; use two for the six NACs
on 100 W amplifiers;
Firefighters Telephone Options
Model Description Size Supv. In Use
4100-1272 Expansion Telephone Control Module with three Class B telephone NACS; required when
telephone circuits are mounted in transponder; 1 Block 75 mA 329 mA
max.
4100-1273 Telephone Class A Adapter Module; mounts on 4100-1272; no additional current required
* Refer to document S4100-0034 for additional audio information. Continued on next page
MINIPLEX Transponder Product Selection (Continued)

6 S4100-0035-6 4/2005
Audio Expansion Signal Module and Options
Model Description Details and Mounting Reference
4100-5116
Expansion Signal Module; three, 1.5 A Class B
NACs for Audio applications; up to five maximum
per amplifier; NAC rating = 1.5 A, 50 W, or 100
speakers maximum
Converts one NAC input to three NAC outputs; selects between two
inputs; for Flex-35/50 amplifiers only, two input NACs are required; Single
Block module mounts in expansion bay; Supv = 18 mA; Alarm with 100 W
amplifiers = 52 mA; Alarm with Flex-35/50 amplifiers = 80 mA
4100-1266 Expansion Signal Module NAC Expander; NAC
rating = 1.5 A, 50 W, or 100 speakers max.
Expands module capacity to six, Class B NACs;
Supv = 0.6 mA; Alarm = 60 mA
4100-1267 Expansion Signal Module Class A Adapter; NAC
rating = 1.5 A, 50 W, or 100 speakers max.
Converts 3 Class B, NACs to Class A; Supv = 0.6 mA;
Alarm = 30 mA
4100-1268
Expansion Signal Module Constant Supervision
Adapter; Converts 3 Class B NACs to Constant
Supervision Class B or Class A NACs; for
25 VRMS or 70.7 VRMS audio
NAC rating = 1.4 A, 50 W, or 100 speakers max.;
Current vs operating voltage: 25 VRMS Supv = 10 mA;
25 VRMS Alarm = 35 mA; 70.7 VRMS Supv = 38 mA;
70.7 VRMS Alarm = 60 mA
These
modules
mount on the
4100-5116;
select one
max. per
4100-5116
as required
General Audio Options
Model Description
4081-9018 End-of-line resistor harness for 70.7 VRMS NACs; 10 k:, 1 W
4100-2320 Audio Bay-to-Bay Interconnection Harness Kit; order one for each audio bay addition
4100-0637 Audio Box Interconnection Harness Kit; order one for each close-nippled audio cabinet
Initiating Device Circuits (IDCs)
Model Description Size Supv. Alarm
4100-5005 Eight zones, Class B 1 Slot 75 mA 195 mA
4100-5015 Eight zones, Class A 1 Slot 75 mA 195 mA
Addressable Interface Modules
Model Description Size Supv. Alarm
4100-3101 IDNet Module, 250 point capacity With 250 IDNet devices, add – 200 mA 250 mA
4100-3104 IDNet Module, 127 point capacity With 127 IDNet devices, add – 102 mA 127 mA
4100-3105 IDNet Module, 64 point capacity With 64 IDNet devices, add – 51 mA 64 mA
Module without devices – 75 mA 115 mA
IDNet Modules, Specifications for each capacity; Module size = 1 Block Loading per IDNet device – 0.8 mA 1 mA
Model Description Size Supv. Alarm
Module without devices – 270 mA 290 mA
4100-3102 MAPNET II®Module, 127 point capacity, add devices separately;
Module size = 2 Slots; Loading per MAPNET II device = 1.7 mA Fully loaded module, total – 470 mA 490 mA
4100-3103
Isolator Module for MAPNET II or IDNet communications; converts one SLC into four
isolated Class A or Class B outputs; up to two Modules can be connected to one SLC;
NOTE: Compatible with MAPNET II Remote Isolators only; for quad isolation with IDNet
Remote Isolators, use 4100-3107 IDNet+ Module (refer to data sheet S4100-0046 for
details)
1 Slot 50 mA 50 mA
Relay Modules; Nonpower-Limited
Model Description Resistive Ratings Inductive Ratings Size Supv. Alarm
4100-3202 4 DPDT w/feedback 10 A 250 VAC 10 A 250 VAC 2 Slots 15 mA 175 mA
4100-3204 4 DPDT w/feedback 2 A 30 VDC/VAC 1/2 A 30 VDC/120 VAC 1 Block 18 mA 70 mA
4100-3206 8 SPDT 3 A 30 VDC/120 VAC 1-1/2 A 30 VDC/120 VAC 1 Block 16 mA 200 mA
Current Calculation Notes:
1. For total supervisory current, add panel module currents to base system value and add all external loads panel-powered loads.
2. For total alarm current, add panel module currents to base system alarm current and add all panel NAC loads and all external loads
powered from panel power supplies.
120 VAC Models 3.5 A maximum @ 102 to 132 VAC, 60 Hz
Input Power [System (SPS); Expansion (XPS);
Remote (RPS); TrueAlert Power Supplies (TPS);
and 100 W amplifiers] 220-240 VAC Models 1.75 A maximum @ 204 to 264 VAC, 50/60 Hz;
separate taps for 220/230/240 VAC
Total Power Supply
Output Rating
9 A total @ nominal 28 VDC, including module currents and
auxiliary power outputs
Auxiliary Power Tap 2 A maximum @ nominal 28 VDC
Power Supply Output
Ratings (System,
Expansion, and Remote
Power Supplies) NACs Programmed
for Auxiliary Power 2 A maximum per NAC, 5 A maximum @ nominal 28 VDC
Output switches to
battery backup
during mains AC
failure or brownout
conditions
Battery capacity range 6.2 Ah to 50 Ah; selectable via programming for batteries below 18 Ah; the SPS is UL
listed for up to 110 Ah battery charging for remotely located batteries
Battery Charger
(System and Remote
Power Supply) Charger characteristics
and performance
Temperature compensated, dual rate, recharges depleted batteries within 48 hours per
UL Standard 864, to 70% capacity in 12 hours per ULC Standard S527
Operating Temp. Range 32° to 120°F (0° to 49° C)
Environmental Operating Humidity Range Up to 93% RH, non-condensing @ 90° F (32° C) maximum
MINIPLEX Transponder Product Selection (Continued)
General Specifications

7 S4100-0035-6 4/2005
Slot 1 Slot 8Slot 7Slot 6Slot 5Slot 4Slot 3Slot 2
Expansion Bay Chassis
Block A
Block B
Block C
Block D
Block E
Block F
Block G
Block H
Size Definitions: Block = 4” W x 5” H (102 mm x 127 mm) card area
Slot = 2” W x 8” H (51 mm x 203 mm) motherboard with daughter card
4-1/2"
(114 mm)
Local Mode Controller dimensions, 6-3/8" (162 mm)
Box dimensions, 6-1/2" (165 mm)
4-5/8"
(117 mm)
1-3/4"
(44 mm)
Matching box is supplied with surface mount models
4601-9109 (red) and 4601-9111 (beige); for semi-flush models 4601-9108
(red) and 4601-9810 (beige), use a 1-1/2" (38 mm) minimum depth, 3-gang box
Fire Alarm Local Mode Controller
ENABLE
CONTROL
Alarm
Alarm
Silenced
Local
Mode
Active
Power
On
Alarm
Silence Reset
Local
Mode
Control
See Operating Instruction 579-343
1" (25.4 mm)
into box
Local Mode Controller to Transponder Wiring:
1. Wire close-nippled to transponder, maximum distance = 20 ft (6.1 m).
2. Nine wires required: 24 VDC (2), one per LED indicator (4), and one per switch (3).
3. Wire size, 18 AWG (0.82 mm² ).
Expansion Bay Module Loading Reference
Description Mounting
Transponder Interface Modules Block A
Audio Riser Modules Block B
Terminal Block Module 1 Block
IDNet Modules 1 Block
4, 2 A Relays 1 Block
4, 10 A Relays 4”, 2 Slots
8, 3 A Relays
NON
Power-limited 1 Block
VESDA Interface 2”, 1 Slot
Class B IDC 2”, 1 Slot
Class A IDC 2”, 1 Slot
MAPNET II Module 4”, 2 Slots
MAPNET II/IDNet Isolator 2”, 1 Slot
Decoder Module 6”, 3 Slots
System, Remote, or TrueAlert
Power Supply
Blocks E, F, G & H
ONLY
Expansion Power Supply Blocks G & H ONLY
NAC Expansion Module On XPS ONLY
Flex-35 Amplifiers, 2 max /bay* Blocks E & F; C & D;
or A & B
Flex-50 Amplifiers, 2 max/bay* Blocks E & F or C & D
100 W Amplifiers, 1 max/bay Blocks E, F, G & H
100 W Backup Amplifiers, 1 max.
per bay with primary amplifier Blocks A, B, C & D
Telephone Expansion Module 1 Block
Expansion Signal Module 1 Block
*NOTE: When mounting dual Flex amplifiers on an
expansion bay, special mounting rules apply.
Local Mode Controller Detail

Tyco, Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, MINIPLEX, and TrueAlert are trademarks of Tyco International Services AG or its affiliates in the
U.S. and/or other countries. VESDA is a trademark of Vision Products Pty Ltd.
Door thickness
1-3/8"(35 mm)
Exposed cabinet for
semi-flush mounting
1-3/8" (35 mm)
minimum
Exposed door and
cabinet for semi-
flush mounting
2-3/4" (70 mm)
minimum
24" (610 mm)
8-3/8"
(213 mm)
6-29/32"
(175 mm)
4" stud
6" stud
Knockout screw/nail holes
(for semi-flush mounting)
Stud alignment
markers, each side
Wall board reference
for semi-flush
mounting, 6" stud
Optional semi-flush
trim kit reference
Front view, box outline without door Side view with door attached
2 Bay height 40" (1016 mm)
Doors can be hinged left or right
3 Bay height 56" (1422 mm)
Tyco Safety Products Westminster • Westminster, MA • 01441-0001 • USA S4100-0035-6 4/2005
www.tycosafetyproducts-usa-wm.com
© 2005 Tyco Safety Products Westminster. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Enclosure Installation Reference
NOTE: A system ground must be provided for Earth Detection and transient protection devices. This connection
shall be made to an approved, dedicated Earth connection per NFPA 70, Article 250, and NFPA 780.