Simplicity 2442 Setup guide

Attachment
Illustrated
Parts List
Rev. 03/2008
500 N. Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
MANUFACTURING, INC.
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.2008 TP 400-2442-01-AT-SMA
Mf
g
. No. Descri
p
tion
Attachment
1692150 Catcher, Clean Sweep Twin, 34"
1730792
Part No.:

Table Of Content
s
Torque Specification Chart ..................................................................... Inside Back Cover
PRODUCT COMPONENTS PAGES
Adapter, Blade & Tube Group ............................................................................................................................. 4
Cover & Bag Group - Twin ................................................................................................................................... 6
Hitch Group .......................................................................................................................................................... 8

Adapter, Blade & Tube Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
984490
The above parts group applies to the following Mfg. Nos.:
4
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Adapter, Blade & Tube Group
Footnotes
NUT, Hex Washer Assembly, Hex, #10-321 1928919SM 4 EXHAUST SHIELD, Front2 1713286ASM 1 SCREW, Truss Head, 10-32 x 1/23 1930531SM 4 EXHAUST SHIELD, Rear4 1713287ASM 1 TUBE, Transfer5 1703769SM 1 CAPSCREW, Hex Head, 5/16-18 x 3/46 1960122SM 1 WASHER, Flat, 5/167 1919326SM 1 LATCH, Tube8 1704603SM 1 WASHER, Flat, 5/169 1960185SM 1 NUT, Flange Lock, 5/16-1810 1935048SM 1 CAPSCREW, Hex Head, 5/16-18 x 3/411 1960371SM 3 WASHER, Special12 1704341SM 1 LOCKNUT, Hex, 5/16-1813 1919438SM 3 ADAPTER14 1709135SM 1 BRACKET, Attachment15 1704355ASM 1 NUT, Centerlock, 5/16-1816 1928698SM 1 WING NUT ASSEMBLY 5/1617 1679163SM 1 NUT, Hex Flange, 5/16-1818 1927557SM 1 CUP19 1679164ASM 1 NUT, Hex, 5/16-1820 1917372SM 3 LOCKWASHER, 5/1621 1917356SM 3 SPACER22 1674669SM 2 CARRIAGE BOLT, 5/16-18 x 2-1/423 1960273SM 1 CARRIAGE BOLT, 5/16-18 x 1-3/424 1931338SM 2 BAFFLE25 1709112A 1 CARRIAGE BOLT, 5/16-18 x 5/826 1931332SM 1 ADAPTER, Blade, High Lift27 1705010SM 1 BLADE, High Lift28 1706739ASM 1
The above parts group applies to the following Mfg. Nos.:
5
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

Cover & Bag Group - Twin
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
983952
The above parts group applies to the following Mfg. Nos.:
6
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Cover & Bag Group - Twin
Footnotes
TUBE ASSEMBLY Support (Incl. Ref. Nos. 2, 3, 4, 5, 6, 8, 9 & 11)1 1704615SM 1 RIVET, Pop2 1960381SM 7 SUPPORT, Tube3 1704075SM 1 SEAL, Cover4 1704135SM 1 BRACKET, Seal5 1704508SM 3 SCREW, Round Head, #8-32 x 7/86 1960399SM 1 LOCKNUT, Flange, 1/4-207 1930642SM 5 WASHER8 1960096SM 2 STRAP, Tube Support9 1704507SM 1 SCREW, Taptite, 1/4-20 x 3/810 1929000SM 2 NUT, Hex, Lock, #8-3211 1960077SM 2 CARRIAGE BOLT, 1/4-20 x 5/812 1960252SM 5 CROSS ASSEMBLY13 1727129ASM 1 CROSS ASSEMBLY13 1727129ASM 1 CAPSCREW, Hex Head, 3/8-16 x 7/814 1921966SM 4 NUT, Hex, Whizlock, 3/8-1615 1928352SM 4 CLIP, Hairpin16 1960221SM 2 SCREEN17 1703700SM 1 NUT, Hex, 5/16-1818 1917372SM 4 LOCKWASHER, 5/1619 1917356SM 4 CLAMP20 1672023ASM 2 HANGER21 1703807ASM 2 CARRIAGE BOLT, 5/16-18 x 3/422 1931333SM 4 HOOP, Bag23 1703855ASM 2 BAG, Grass24 1703764SM 2 TUBE CLIP, Grass Bag25 1675707SM 2 SEAL, Clip26 1704057SM 1 SCREW, Truss Head, #10-32 x 1/227 1930531SM 2 RIVET, Pop28 1675043SM 4 HANDLE, Latch29 1703853SM 1 NUT, Hex, #10-3230 1928919SM 2 PIN, Round Head31 2860367SM 2 WASHER32 1910531SM 4 CLIP, Canoe33 1667248SM 6 DECAL, Safety34 1732820SM 1 COVER35 1704056SM 1 WINDOW36 1704180SM 2 NUT, Speed37 1933886SM 1 CABLE, Double Loop38 1705876SM 1 WASHER, 1/439 1921319SM 1 SCREW, Self-tapping, #10-12 x 5/840 1960400SM 1 COVER ASSEMBLY (Incl. Ref. Nos. 17, 26, 28, 32, 37, 38, 39 & 40)41 1704056SM 1
The above parts group applies to the following Mfg. Nos.:
7
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

Hitch Group
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
984491
The above parts group applies to the following Mfg. Nos.:
8
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Hitch Group
Footnotes
SUPPORT, Catcher1 1709111ASM 1 PIN, Round Head, Drilled2 2102004SM 1 SUPPORT ASSEMBLY3 1709022ASM 1 CLIP, Pin, Safety4 2176012SM 1 CAPSCREW, Hex Head, 5/16-18 x 35 1960590SM 4 WASHER, Plain 5/166 1919326SM 8 ANCHOR ASSEMBLY, Older Models7 1709026ASM 2 ANCHOR ASSEMBLY, Newer Models7 1726975ASM 2 NUT, Hex Flange Two-Way Lock 5/16-189 1935048SM 4
The above parts group applies to the following Mfg. Nos.:
9
2008Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1692150 - Catcher
TP 400-2442-01-AT-SMA

Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of in/lbs in/lbs in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 19 2.1 30 3.4 41 4.6
8-36
20 2.3 31 3.5 43 4.9
10-24
27 3.1 43 4.9 60 6.8
10-32
31 3.5 49 5.5 68 7.7
1/4-20
66 7.6 810.9 12 16.3
1/4-28
76 8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware
excluding:locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common HardwareTypes
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside
Diameter
Nut, 1/2”
No
Marks
3/8”Bolt or Nut
Wrench—9/16”
3/8
5/16”Bolt or Nut
Wrench—1/2”
5/16
1/4”Bolt or Nut
Wrench—7/16”
1/4
1/2”Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16
DIA.
7/16”Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size , meaning the inside diameter is 1/2 inch; if a
second number is present it represent the
threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
Nominal size , or body diameter is 1/2 inch; the
second number represents the
threads per inch (16 in this
example, and the final number is the
body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4