Simrad NSE8 User manual

www.simrad-yachting.com A brand by Navico - Leader in Marine Electronics
Installation Manual
Simrad NSE8 and NSE12
Multi-function Displays
English

| 1
Preface
Disclaimer
As Navico is continuously improving this product, we retain the right to make changes to
the product at any time which may not be reflected in this version of the manual. Please
contact your nearest distributor if you require any further assistance.
It is the owner’s sole responsibility to install and use the instrument and transducers in
a manner that will not cause accidents, personal injury or property damage. The user of
this product is solely responsible for observing safe boating practices.
NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM
ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS,
DAMAGE OR THAT MAY VIOLATE THE LAW.
Governing Language: This statement, any instruction manuals, user guides and other
information relating to the product (Documentation) may be translated to, or has been
translated from, another language (Translation). In the event of any conflict between any
Translation of the Documentation, the English language version of the Documentation
will be the official version of the Documentation.
This manual represents the product as at the time of printing. Navico Holding AS and its
subsidiaries, branches and affiliates reserve the right to make changes to specifications
without notice.
Copyright
Copyright © 2009 Navico Holding AS.
Feedback from you
Your feedback is important and helps Navico ensure that this manual is a valuable
resource for all marine technicians. E-mail your comments or suggestions about this
manual to the following address:
[e-mail]
Warranty
The warranty card is supplied as a separate document.
It is shipped with the product registration card.
In case of any queries, refer to the brand web site of your display or system.
www.simrad-yachting.com

2 |
Declaration of Conformity
GB Hereby, Navico Holding AS declares that this NSE8, NSE12 is in com-
pliance with the essential requirements and other relevant provi-
sions of Directive 1999/5/EC.
FI Navico Holding AS vakuuttaa täten että NSE8, NSE12 tyyppinen
laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koske-
vien direktiivin muiden ehtojen mukainen.
NL Hierbij verklaart Navico Holding AS dat het toestel NSE8, NSE12 in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
FR Par la présente, Navico Holding AS déclare que ce NSE8, NSE12 est
conforme aux exigences essentielles et aux autres dispositions de la
directive 1999/5/CE qui lui sont applicables.
SE Härmed intygar Navico Holding AS att denna NSE8, NSE12 står i
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
DK Undertegnede Navico Holding AS erklærer herved, at følgende ud-
styr NSE8, NSE12 overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/ EF.
DE Hiermit erklärt Navico Holding AS, dass sich dieses NSE8, NSE12 in
Übereinstimmung mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.
(BMWi)
GR Με την παρουσα Navico Holding AS δηλωνει οτι NSE8, NSE12
συμμορφωνεται προς τις ουσιωδεις απαιτησεις και τις λοιπες σχετικες
διαταξεις της οδηγιας 1999/5/ΕΚ.
IT Con la presente Navico Holding AS dichiara che questo NSE8, NSE12
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
ES Por medio de la presente Navico Holding AS declara que el NSE8,
NSE12cumple con los requisitos esenciales y cualesquiera otras dis-
posiciones aplicables o exigibles de la Directiva 1999/5/CE.
PT Navico Holding AS declara que este NSE8, NSE12está conforme com
os requisitos essenciais e outras provisões da Directiva 1999/5/CE.
The equipment named in this declaration, is intended for use in international waters
as well as coastal sea areas administered by countries of the E.U. and E.E.A. A full
Declaration can be obtained from www.www.simrad-yachting.com
Disposal
Waste Electrical and Electronic Equipment (WEEE)
The use of the WEEE Symbol indicates that this product may not be treated as household
waste. By ensuring this product is disposed of correctly, you will help protect the
environment.
For more detailed information about the recycling of this product, please contact your
local authority, your household waste disposal service provider or the shop where you
purchased the product.

| 3
Contents
Introduction ...........................................................................................6
About this manual .................................................................................. 6
Conventions .......................................................................................... 6
Important safety and warning information................................................. 6
Check the parts..................................................................................... 7
Overview ................................................................................................8
Installing the display............................................................................10
Mounting location................................................................................. 10
Panel mount........................................................................................ 11
Bracket Mount ..................................................................................... 12
System architecture .............................................................................14
Networking, Data Interfacing................................................................. 14
SimNet / NMEA 2000 ......................................................................... 14
Ethernet: (NETWORK ports)................................................................ 14
NMEA0183 ........................................................................................ 14
Data Bridging.................................................................................... 15
Wiring the NSE .....................................................................................22
Power................................................................................................. 23
Connecting power.............................................................................. 23
Power control.................................................................................... 23
No Power Control...........................................................................................24
Auto Power on...............................................................................................24
Power Control Master .....................................................................................24
External alarm..................................................................................... 26
SimNet ............................................................................................... 27
SimNet: The basics ............................................................................ 27
Planning and installing a SimNet backbone............................................ 28
Power the SimNet network.................................................................. 28
Ethernet ............................................................................................. 31
Dual and Multi Station ........................................................................ 32
NMEA0183 wiring ................................................................................. 33
Video In.............................................................................................. 34
Video Out ........................................................................................... 35
Connecting BR24 Radar ....................................................................... 36
Connecting HD Radar ........................................................................... 37
Connecting BSM1 Broadband Echosounder .............................................. 38

4 |
Commission the system........................................................................39
Turning on the system for the first time .................................................. 39
Operating the menu system .................................................................. 39
Commissioning checklist ....................................................................... 40
System settings menu........................................................................ 41
Language ......................................................................................... 41
Time: Local Time, Time format, Date Format......................................... 41
Power Control ................................................................................... 41
Echosounder setup............................................................................... 42
Depth offset..................................................................................................42
Water speed calibration ..................................................................................42
Echo sounder software version........................................................................42
Water speed averaging...................................................................................43
Temperature calibration..................................................................................43
Transducer type.............................................................................................43
Radar setup ........................................................................................ 43
Radar software version...................................................................................43
Radar Transmit, Standby or off ........................................................................44
Data setup .......................................................................................... 45
SimNet / NMEA2000 setup.................................................................. 45
Source selection (Auto select) ............................................................. 45
Source selection (Manual) .................................................................. 45
Group Source Selection (SIMRAD)....................................................................45
Group Source Selection (NONE).......................................................................46
Source selection advanced..............................................................................46
Damping .......................................................................................... 48
Device List........................................................................................ 48
Serial port setup.................................................................................. 49
NMEA 0183 output ............................................................................. 49
Fuel ................................................................................................... 50
Vessel Setup ..................................................................................... 50
AIS own vessel .................................................................................... 50
Diagnostics ......................................................................................... 51
NMEA2000 Diagnostics....................................................................... 51
USER Database UDB .......................................................................... 51
Check GPS signal ................................................................................. 52
System backup.................................................................................... 52
Restore a backup............................................................................... 52
Software upgrades............................................................................... 53
Displaying current software version ..................................................... 53
NSE Display software version ..........................................................................53
Ethernet module software version....................................................................53
Additional NSE display upgrade steps ...............................................................54

| 5
Screen capture .................................................................................... 55
File transfer ........................................................................................ 55
Drawings ..............................................................................................56
NSE8 Dimensions................................................................................. 56
NSE12 Dimensions ............................................................................... 57
Spare parts...........................................................................................59
NSE Spare parts .................................................................................. 59
Compatible BSM-1 Transducers............................................................ 60
SimNet accessories ............................................................................ 60
Ethernet cables (yellow) ..................................................................... 61
Ethernet cables (RJ45) ....................................................................... 61
Repeat screens.................................................................................. 61
Video cables for repeat screens ........................................................... 61
Specifications .......................................................................................62
Supported NMEA0183 sentences ............................................................ 63
NMEA 2000 PGN List ............................................................................ 64
NMEA 2000 PGN Receive .................................................................... 64
NMEA2000 PGN Transmit.................................................................... 65

6 | Introduction
Introduction
About this manual
This manual is a reference guide for installing the Simrad NSE8 and NSE12 Multi Function
Display.
The information in this manual at the time of printing is correct to the best of our
knowledge. Navico can not be liable for any inaccuracies or missing information.
Due to the constant improvement of Navico’s products. Navico cannot be liable for
changes between the product and the manual. Refer to www.simrad-yachting.com for
the latest manuals and addendums.
Conventions
Used when it is necessary to warn personnel that a risk of damage to the
equipment or injury/death exists if care is not exercised.
Used to draw the reader’s attention to a comment or some important information.
Important safety and warning information
Please read carefully before use.
When navigating the vessel, use the Simrad NSE system only as a navigational
aid. Proper navigation of the vessel is the sole responsibility of the vessel
operator.
The electronic chart used by the NSE System is an aid to navigation only
and is designed to supplement, not replace, official government charts. Only
official government charts supplemented by notices to mariners contain the
information required for safe and prudent navigation. Always supplement the
electronic information provided by the Simrad NSE with other plotting sources
such as observations, depth soundings, radar and hand compass bearings.
Should the information not agree, the discrepancy must be resolved before
proceeding any further.
Never operate the NSE in Simulate Mode while you are underway. It is the
user’s responsibility to ensure that Simulate Mode is used only in safe
situations such as when you are moored in a marina.
The Global Positioning System (GPS) is operated by the US Government which is
solely responsible for its operation, accuracy and maintenance. The GPS system
is subject to changes which could affect the accuracy and performance of all
GPS equipment anywhere in the world.
The accuracy of the Echosounder depth display can be limited by many
factors, including the type of transducer, the location of the transducer, and
water conditions. Ensure that the transducer is installed correctly and the
Echosounder is used correctly.

Introduction | 7
Check the parts
Packaged parts list
NSE8
8.4 “ Display unit
PN location specific
NSE8 Bezel
000-00132-001
NSE12
12 “ Display unit
PN location specific
NSE12 Bezel
000-00133-001
NSE8 Dust cover
000-00134-001
NSE8 Gasket
NSE12 Dust cover
000-00135-001
NSE12 Gasket
NSE8 Mounting bracket
000-00136-001
NSE8, NSE12
Bracket knobs
000-00138-001
NSE12 Mounting
bracket
000-00137-001
NSE8, NSE12
2 x Ratchet washers
072-2559-001
NSE8 Cut-out Template
988-0175-05
212 mm (8.34”)
285 mm (11.20)
265 mm (10.40”)
CLEARANCE HOLE TO SUIT M4 MACHINE SCREW
OR DRILL PILOT HOLE TO SUIT SELF TAPPING SCREW
5 mm (0.20”)
192 mm (7.55)
NX50
192 mm (7.55”)
265 mm (10.40”)
PRODUCT OUTLINE
25 mm (1.00”)
CUTOUT
Check dimensions before cutting
NSE8, NSE12
Power cable
000-00128-001
NSE12 Cut-out
Template
988-0175-06
NSE8, NSE12
Video-In / Comms
Cable
000-00129-001
NSE8, NSE12
Connector Caps
000-00130-001
NSE8, NSE12
Installation Manual
988-0175_03
NSE8, NSE12
Operation manual
988-0175-02
NSE8, NSE12
Quick start guide
988-0175-04
NSE8, NSE12
Cleaning cloth
MS000682A-G
NSE8, NSE12
5 x SCREW,14G x
1,PAN POZI,S/T,SS
316,BLACK
NSE8, NSE12
4 x SCREW,
8Gx1, PAN POZI,
S/T,16,LO-HEAD
SimNet Starter Kit: Includes
• 24005845 SimNet 5 m (16.5 ft) cable
• 24006298 SimNet 7-Prong Multi-Joiner
• 24005894 SimNet Termination Plug
• 24005902 SimNet 2 m (6 ft) power cable
w/terminator

8 | Overview
Overview
ECHORADARCHART NAV INFO PAGES
MENU
PLOT GO TO
MARK VESSEL
WIN
IN
MOB ABC DEF
123
JKLGHI MNO
456
TUV PQRS WXYZ
7
STBY
AUTO
PWR
8
0
9
OUT
1
2 4
6
7
9
11
5
8
10
13
13
14
15
16
12
3
Key Description
1Direct Access Keys (DAK). Provide direct access to a page. Repeated presses
of each DAK cycles through several different pages that relate to the DAK
2PLOT/MARK key. A short press activates the Plot menu, a long press positions
a waypoint at the vessel position
3 Rotary knob. The function of the knob is depending on active context
4GOTO/VESSEL key. A short press activates the Goto menu, a long press cen-
ters the chart to vessel position
53key — Activates/confirms current selection
6 X key cancels changes and returns to previous menu level
7Cursor keypad used to move the cursor on the display, and to maneuver in the
menu system
8MENU key. Used to display the context menu for the active panel/overlay, and
for selecting options in edit mode. . 2 x MENU for system settings menu
9WIN key, used on multiple panels pages. A short press toggles between the
panels, a long press expands active panel to a full page panel and back again
10 Zoom buttons for radar, echosounder and chart pages
11
Alpha numeric keypad used for entering numbers and text in dialog boxes.
A long press on the “1” key will position a Man Over Board (MOB) waypoint at
the vessel’s current position
12 STBY AUTO - Future use
13
Media port door. Press and slide to the right to open.
Media can be used for optional Navionics chart data, software updates, trans-
fer of user data and system backup
14 SD /MMC media card slot.
15 USB port
16 Removable bezel

Overview | 9
12 5 6
3
4
Key Description
1
Power. For power input 12 or 24 V DC input (see power page 23), Power con-
trol (see Power Control page 23) and external alarm (see External Alarm
page 26).
2
Video In. Supplied cable provides two composite video inputs (see Video In
page 34) and one RS422 port (NMEA0183 TX, RX) see NMEA0183 Wiring
page 33
3SimNet. Connects NSE display to a SimNet or NMEA2000 network (see
SimNet page 27).
4Video Out. Connect to an external monitor via optional DVI cable (see Video
Out page 35).
5Network 1, 2 and 3. Three Ethernet network ports for connecting to other NSE
displays and Network modules. (see Ethernet on page 31)
6
USB. Used for Software updates, chart data base updates, backing up way-
points routes and tracks. A better option to the front port if it is exposed to
the weather.
Note. A Water proof optional USB cable is available to extend this port to a dry
location. (AA010078 USB dash mount)

10 | Installing the display
Installing the display
Mounting location
Choose the mounting locations carefully before you drill or cut. The display should be
mounted so that the operator can easily use the controls and clearly see the display
screen. Be sure to leave a direct path for all of the cables. The display screen is high-
contrast and anti-reflective, and is viewable in direct sunlight, but for best results install
the display out of direct sunlight. The chosen location should have minimal glare from
windows or bright objects.
Ensure that any holes cut are in a safe position and will not weaken the boat’s structure.
If in doubt, consult a qualified boat builder.
At least 100 mm (4”) away from the compass, at least 300 mm (12”) away from any
radio transmitter and at least 1.2 m (4 ft) away from any antenna.
Before cutting a hole in a panel, make sure that there are no hidden electrical wires or
other parts behind the panel.
Do not mount any part where it can be used as a hand hold, where it might be
submerged, or where it will interfere with the operation, launching or retrieving of the
boat.
If bracket mounting chose a flat area where the display will not be subjected to excessive
vibration.
Leave sufficient clearance space behind the display to connect all relevant cables.
Good ventilation is required behind the mounting panel. Poor ventilation may cause the
display to overheat. The display is designed to operate in temperatures from -15° C to
+55° C (+5° F to +131° F).
For overall width and height requirements, please see the drawings at the back of this
manual.

Installing the display | 11
Cut out shaded
area
Panel mount
212 mm (8.34”)
285 mm (11.20)
265 mm (10.40”)
CLEARANCE HOLE TO SUIT M4 MACHINE SCREW
OR DRILL PILOT HOLE TO SUIT SELF TAPPING SCREW
5 mm (0.20”)
192 mm (7.55)
NSE-8
192 mm (7.55”)
265 mm (10.40”)
PRODUCT OUTLINE
25 mm (1.00”)
CUTOUT
Check dimensions before cutting
Attach the flush mounting template1 to the selected mounting position
using adhesive tape.
Drill pilot holes for the four hole saw2 cuts and four self tapping screws
used to secure the display. If using
M4 machine screws use a 5 mm
(0.20 ”) drill bit.
A
ed
de
ea
a
ou
re
ut
t o
ad
a
s
ha
t
ut
C
Cu
Use a 25mm (1 “) hole saw to cut3 the four corner radius Cut along the dotted line and4 remove the shaded area.
Peel backing off the gasket and apply to the surface.5
Connect all cables to the rear of the unit before placing the unit into the console.6
Secure the display to the surface7
To finish off the installation firmly clip the front bezel in place8

12 | Installing the display
Bracket Mount
An alternative to flush mounting the NSE8 or NSE12 is to bracket mount the unit. This
method has the advantage that the display can easily be removed when not in use. The
display may be tilted for best possible viewing angle when bracket mounted.
Press the ratchet washers into the1
bracket.
Loosely screw securing knobs to the2
Display unit.
Temporarily mount the display3
unit in the bracket and make sure
the display can be adjusted to the
correct angle without interfering
with the surrounding. Allow space
for cables attached to the rear of
the unit.
Remove the display unit and use the4
mounting bracket as a template to
mark the five positions of the screw
holes.

Installing the display | 13
Drill a pilot hole for the five screws5
and an optional hole large enough
for the cables to emerge from.
Secure 5 the bracket to the surface6
Connect the cables.7
Slide the display into the mounting8
bracket and secure in place with the
bracket knobs.
Attach the bezel. Firmly clip the9
front bezel in place.
NSE Bezel removal
A
BC
Protect the dash area adjacent to the top edge (or bottom edge) of the display.
Apply upwards pressure on the bezel (A), this will create an opening between the
bezel and the case. Insert a medium size flat blade screw driver into the gap (B) Slide
the screw driver along the gap to release the clips along the top. Continue down the
side until the bezel releases. The same routine can be applied to the bottom edge if
accessible.

14 | System architecture
System architecture
This section explains how the NSE connects to other devices as part of a system. The
NSE has a highly scalable system architecture. A system can consist of a basic stand
alone chart plotter, or expand to a networked, multi-display system connected to a wide
range of accessories.
The system architecture is modular with a wide range of peripherals and accessories
that can be connected to SimNet or NMEA2000 devices such as instrument systems,
AIS, GPS and heading sensor to Ethernet devices such as Radar and Echosounder. For
multi display installations the system can be set up to be truly masterless, i.e. have no
dependency on other displays being powered on.
A NSE display can connect to other devices in the system by Ethernet, SimNet /
NMEA2000 or NMEA0183.
A system can have:
between one and six displays, The displays can be any mix of NSE8 and NSE12•
one radar only•
one echosounder only•
Networking, Data Interfacing
The NSE system can use three data networks. SimNet (NMEA2000), Ethernet and
NMEA0183.
SimNet / NMEA 2000
SimNet is Simrad’s proprietary CAN bus network for transfer of navigation data such•as wind, Position, AIS, etc between all SimNet or NMEA2000 devices on a SimNet/
NMEA2000 network.
SimNet is lower bandwidth than the Ethernet network, but is 50 times faster than•NMEA0183
Ethernet: (NETWORK ports)
NSE uses an Ethernet network for the transfer of high bandwidth data between other•NSE displays and from network modules such as Radar, Echosounder and Weather
module
Each NSE display has three Ethernet network ports. An optional 5 port expansion port•is available. (Recommended for multiple NSE displays)
Ethernet does not transfer navigation data such as position, heading etc. This is•handled either by SimNet and or NMEA 0183. However navigation and display settings
are synchronized over Ethernet
NMEA0183
NMEA0183 is a point to point connection. Each NSE display has one NMEA0183 port•using RS422 protocol. Each display can output to one NMEA0183 “Listener” and
receive from one NMEA0183 “Talker”.

System architecture | 15
Data Bridging
Supported NMEA0183 sentences entering the system are bridged (converted) to•SimNet/NMEA2000 and distributed on the SimNet backbone for all other displays to
use
Certain SimNet /NMEA2000 PGNs (messages/sentences) are bridged across to•NMEA0183 to be available as an output from any NSE display
Ethernet to SimNet. Limited data is bridged from the Ethernet echosounder. Speed,•depth and temperature are bridged to SimNet and NMEA0183. Depth, speed and
temperature data from the echosounder is the only data bridged from Ethernet
PLOT
MARK
GO TO
VESSEL
MENU WIN
OUT RANGE IN
123
65
89
7
PQRS TUV WXYZ
MNO
JKL
ABC DEF
GHI
4
0
STBY
AUTO
MOB MOB
PWR
ECHORADARCHART NAV INFO PAGES
0183
PLOT
MARK
GO TO
VESSEL
MENU WIN
OUT RANGE IN
123
65
89
7PQRS TUV WXYZ
MNO
JKL
ABC DEF
GHI
4
0
STBY
AUTO
MOB MOB
PWR
ECHORADARCHART NAV INFO PAGES
NMEA0183
RX - RX + TX - TX +
NMEA0183 Talker
SimNet Network
GPS Heading
DISPLAY 1 DISPLAY 2
SimNet Network
NMEA0183 Listner
A
B
C
Example of data bridging
A In this example a NMEA0183 (talker) is connected to DISPLAY 1
B The NMEA sentences are bridged across to SimNet and distributed on the
SimNet network
C The NMEA0183 listener connected to DISPLAY 2 can receive the NMEA0183
sentences from the device connected to DISPLAY 1 and also from other de-
vices that are on the SimNet network
An NMEA talker can be connected to each NSE display and both set of data will be
converted to SimNet. Each display can be setup for outputting selected NMEA sentences.
Speed, temp and depth data from the echosounder transducer that is to be displayed
as an instrument has to bridged from ethernet to SimNet. A NSE display has to be
nominated to bridge the data. If this nominated display is turned off, no data will be
displayed, until the display is turned on or another display is selected to bridge the data
(see Source Selection on page 45).
NMEA0183 to SimNet bridging only applies to the NMEA0183 sentences outlined in the
Supported NMEA0183 Sentences section of this manual (see page 62).

16 | System architecture
VIDEO /DATA
NSE Display
POWER
SIMNET
SIMNET NETWORK
Supplied with
display
or accessory
Optional
accessory
RADAR
WEATHER
Amp for
ECHOSOUNDER
VIDEO OUT
Red (FUSE)
Black
Yellow
Power Control Ext. Alarm
Video 1 (Red)
12 v DC
USA Only
USA Only
NMEA 0183
Video 2 (Green)
Simrad DI10 or DI15
display’s
Note: NSE8 only connects to DI10
NSE12 only connects to DI15
DI15
From
NSE12
MO19
From
NSE12 or NSE8
DI10
From
NSE8
MO19 or third party DVI
Monitor
Note dimming not controlled by NSE
Composite Video
12 or 24 V DC
Blue
+_
RX +Green
Blue
Yellow
Orange
TX +
TX -
RX -
NMEA 0183
Serial port
1 x RS422 port
GPS
AIS
Instuments
Autopilot
Heading
Depth
Engines
NMEA2000
BR24 Broadband Radar
SimNet starter kit
SimNet devices
Power cable w/term
Drop cable 2 m (6 ft)
Termiator plug
7 way joiner
BSM1 Broadband
Echo Sounder
Sirius satelite weather and radio
Pulse Radar
2,4,6,10 or 25 kW
Power cable
Video In / Data cable
OR
OR
Ethernet Adapter
DVI Video Cable
+_
Ethernet 5 Pin 2m (6.5 ft)
Ethernet RJ45 2m (6.5 ft)
Ethernet 5 Pin 2m (6.5 ft) Ethernet 5 Pin 2m (6.5 ft)
Audio cable
T
T
SimNet cable 2m (6.5 ft)
Single station configuration possibilities

System architecture | 17
Green
Blue
Yellow
Orange
SIMNET SIMNET
Supplied with
display or accessory
Optional
accessory
RADAR RADAR
ECHOSOUNDER
NSE8 or NSE12 NSE8 or NSE12
Video 1
SimNet Starter kit
NMEA 0183NMEA 0183
Video 2
Video 1
Video 2
Cameras
RX +
TX +
TX -
RX -
RX +
TX +
TX -
RX -
GPS
Instuments
Autopilot
Heading
Depth
Engines
AIS
NMEA2000
BR24 Broadband Radar Pulse Radar
2,4,6,10 or 25 kW
Video In / Data
OR
DVI Video Cable
Video In / Data
Ethernet 5 Pin 2m (6.5 ft)
Ethernet Adapter
5 pin to RJ45
EthernetEthernet
WEATHER
USA Only
T
T
VIDEO OUT
Simrad DI10 or DI15
display’s
Note: NSE8 only connects to DI10
NSE12 only connects to DI15
DI15
From
NSE12
MO19
From
NSE12 or NSE8
DI10
From
NSE8
MO19 or third party DVI
Monitor
Note dimming not controlled by NSE
OR
Ethernet 5 Pin 2m (6.5 ft)
SimNet cable 2m (6.5 ft) SimNet cable 2m (6.5 ft)
Ethernet 5 Pin 2m (6.5 ft)
Ethernet RJ45 2m (6.5 ft)
Power cable w/term
Drop cable 2 m (6 ft)
Termiator plug
7 way joiner
Dual station configuration possibilities

18 | System architecture
J1 J2
J3
J1 J2
J3
Suggested system POWER BOATS 26-40 ft
T
T
SimNet drop cable SimNet backbone SimNet terminator Ethernet
RC42 AC 12
RF25NAIS-300
GPS Ant
SimNet to
Micro-C cable
VHF
7 way joiner
7 way joiner
BSM-1
Tansducer
BR24
NSE
AP24 IS20 Graphic
GS15
SimNet inline joiner
(w/terminator)
NMEA0183 Out
NSE
(optional 2nd display)
RD68
RI10
NMEA2000 Engines
P
P
SimNet power 12 V DC (with terminator)
TX +
RX +
RX -
TX -