Simrad MO16-T User manual

ENGLISH
MO Series Monitors
User Manual
simrad-yachting.com

| 3
MO Series User Manual
Preface
As Navico is continuously improving this product, we retain the right to make changes to the
product at any time which may not be reected in this version of the manual. Please contact
your nearest distributor if you require any further assistance.
It is the owner’s sole responsibility to install and use the instrument and transducers in a
manner that will not cause accidents, personal injury or property damage. The user of this
product is solely responsible for observing safe boating practices.
NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL
LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE
OR THAT MAY VIOLATE THE LAW.
Governing Language: This statement, any instruction manuals, user guides and other
information relating to the product (Documentation) may be translated to, or has been
translated from, another language (Translation). In the event of any conict between any
Translation of the Documentation, the English language version of the Documentation will be
the ocial version of the Documentation.
This manual represents the product as at the time of printing. Navico Holding AS and its
subsidiaries, branches and aliates reserve the right to make changes to specications
without notice.
Copyright
Copyright © 2016 Navico Holding AS.
Warranty
The warranty card is supplied as a separate document.
In case of any queries, refer to the brand website of your display or system:
www.simrad-yachting.com
Compliance Statements
The Simrad MO series monitors:
• complies with CE under EMC directive 2004/108/EC
• complies with the requirements of level 2 devices of the Radio-communications
(Electromagnetic Compatibility) standard 2008
The relevant Declaration of Conformity is available in the following website under model
documentation section: www.simrad-yachting.com
Warning
The user is cautioned that any changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Trademarks
• NMEA 2000 is a registered trademark of the National Marine Electronics Association
• Navionics is a registered trademark of Navionics SpA
• Simrad is a trademark of Kongsberg Maritime AS Company registered in the US and other
countries and is being used under license
• B&G, StructureScan, Navico, SonicHub, SimNet, Skimmer, InsightHD, Broadband Radar
and Broadband Sonar are trademarks of Navico, registered in the US and other countries

4 |MO Series User Manual
About this manual
This manual is a reference guide for installing and operating the Simrad MO Series monitors.
The manual does not cover basic background information about how equipment such as
radars, echosounders and AIS work.
Important text that requires special attention from the reader is emphasized as follows:
¼Note: Used to draw the reader’s attention to a comment or some important information.
!
Warning: Used when it is necessary to warn personnel that they should proceed
carefully to prevent risk of injury and/or damage to equipment/personnel.

| 5
Contents | MO Series User Manual
Contents
6 Introduction
6 Items included
7 Display installation
7 Cutout template
7 Fixing options
8 Flush-mounting the display
11 VESA mounting the display
12 Connecting the display
12 Rear connections
12 Cable retention
13 Connecting power
14 Connecting touch control
14 Serial connection
14 USB connection
15 Connecting NMEA 2000
15 Connecting HDMI cable
15 Typical installation
16 Operating the display
16 First time operation
16 Shortcut functions
16 OSD menu
18 Updating the rmware
18 Checking current rmware version
18 Installing an Update
19 Dimensional drawings
20 Troubleshooting tips
21 Cleaning and maintenance
21 Display removal
21 Replacing the gasket
22 Replacing the lters
22 Other maintenance
23 General specications
24 Accessories

6 |Introduction | MO Series User Manual
Introduction
The Simrad MO Series monitors oer a low prole, high brightness solution for displaying
video from a variety of sources. The range includes six models; the 16”, 19”, and 24”Touch
series, and the 16”, 19”, and 24” Pilot series. The Touch models are suited to both indoor
and outdoor (direct sunlight) use, whereas the Pilot series are suited to enclosed helm
installations. The Pilot series do not utilize a touchscreen, therefore when connected to a
Marine Processor, require an external controller such as the OP40. All monitors in the range
accept video via HDMI, DVI-I and composite inputs.
Items included
1
2
18
12
13
17
16
10
19 20
3
4
5
9
8
6
7
11
15
14
21
1 Monitor
2 Dash mount brackets (x2)
3 Washer, M4, 12 mm, SS (x4)
4 Pozi pan head machine screw, M4 x 12 mm, SS (x4)
5 Plastic spacer (x4)
6 Wing nut M5 (x4)
7 Wing head machine screw (x4)
8 Plastic stopper - dash mount (x4)
9 Pozi pan head self-tapping screw 4G x 1/2” (x12)
10 Cable retention bracket with screws 4G x 1/2” (x4)
11 Cable ties (x4)
12 Connector block (serial data)
13 Micro-C tee piece
14 Micro-C cable, 2 m (6ft)
15 Power cable with connector
16 Bezel trim, black (x2)
17 Bezel trim, silver (x2)
18 Operator manual
19 Cutout template
20 Warranty card
21 Drill and screw guide tool
1

| 7
Display installation | MO Series User Manual
Display installation
It is recommended that the unit be powered and connected to a video source to assist in
selecting a suitable mounting location, prior to irreversable modication of the vessel’s helm
station. When planning the display location, the following points should be considered to
ensure safe, comfortable and reliable operation:
• Convenience - the mounting location should be easily accessible to allow operation of the
controls and should enable easy viewing of the display.
• Viewing angle - the viewing angle inuence the viewability of the monitor. The recom-
mended viewing angles relative to perpendicular are shown in the illustrations below.
MO16
MO19
Horizontal viewing angles
A: Optimum viewing angle
B: Good viewing angle
C: Poor viewing angle or obstructed view
MO24
Vertical viewing angles
• Access - there must be sucient space behind the display to allow cable connections to the
rear connectors, avoiding tight bends in the cable. Also ensure there is sucient access for
tightening wing nuts/screws on the mounting brackets, where used.
• Interference - the selected location should be far enough away from devices that may
cause interference, such as motors, generators and radio transmitters/receivers.
• Magnetic compass - mount the display at least 1 metre (3 ft.) away from a magnetic
compass.
• Environment - to prevent overheating, do not restrict airow at the rear of the display unit;
ensure that there is adequate ventilation, particularly if the display unit is pod-mounted. If the
space behind the display is air conditioned or cooled by a fan, it will help in keeping the unit’s
temperature down when mounted in direct sunlight. The display should be protected from
physical damage and excessive vibration. Although the display unit is waterproof from the
front when installed correctly, it is good practice to mount it in a protected area away from
prolonged and direct exposure to rain and salt spray.
!
Warning: Damage incurred to monitor through failure to provide adequate ventilation
could invalidate your warranty. Do not recess device in to an enclosure shared with a heat
source. e.g. engine compartment.
Cutout template
Use the supplied scale template to help mark up the cutout area.
¼Note: Always check the template dimensions against the physical monitor to ensure
dimensions are correct, prior to making the cutout.
Fixing options
The MO series monitors can be dash or bracket mounted (using optional VESA adaptor).
When dash mounting, unit should be tted using the rear mounted dash mount brackets,
and bezel screws from the front. Exclusion of the dash mount bracket will greatly increase
strain on bezel screws and adjacent bezel plastics, and is not recommended.
2
A
C
C C
C
B
A A
40°
70°
20°
80° 80°
A
C
C
A
80°
80°

8 |Display installation | MO Series User Manual
Flush-mounting the display
¼Note: The following guidelines and warnings apply:
Hard materials e.g. GRP, Acrylic, hardwoods
2.3 - 2.5 mm (3/32")
Important drill bit size selection information
Front mount screw recommendations
Soft materials e.g. Plywood
1.9 - 2.3 mm (5/64")
Max 5.5 mm
(0.22”)
1. Fit the supplied M4 machine screws,
washers, and plastic spacers to each
of the four threaded ttings on the
back case of screen. Hand tighten
only.
REMOVESHADEDAREA
*988-10455-001*
NOTE:
DONOT SCALE
PRINT 1:1
IMPORTANT.Donotuse this template if it has been rescaled
bycopyingor prin ng.If this is not the original, or is a print
fromale, please check the dimension lines below are to
scalebeforeuse.
IMPORTANT.Nepasu liserce gabarit s’il a été photocopié ou
impriméenformat réduit ou agrandi. Si ce gabaritn’est ni un
originalniune version imprimée d’un chier PDF,veuillez
vérierqu’ilest à l’échelleavant de l’u liser.
IMPORTANTE.nousarla plan lla si haypeligro que la escala
originalexactase ha alteradopor copias o procesos de
impresiónimprecisos.Si esto no es el original, o un PDF,veri
carquelas líneas abajo están a la escala antes de usar.
WICHTIG.DiesenVordruck nichtverwenden, wenn er durch
KopierenoderDruckenim Maßstab verändert wurde. Sollte
esnichtdas Original oder ein PDF-Ausdruck sein, müssen
untenstehendeZeilenvor erwendungan den rich gen
Maßstabangepasstwerden.
BELANGRIJK.Gebruikdeze mal niet indien de schaal is veran-
derddoordathet is gecopieerd of gedrukt.Indien deze mal
niethetorigineel of een print van PDF is, controleer dan of de
onderstaandelijnende juisteschaal zijn voordat u ze gebrui-
kt.
IMPORTANTE.Nãou lizeestegabarito se a escala do mesmo
versidoalterada por cópia ou impressão. Se não foro
originalouuma cópia impressa de um arquivo PDF,verique
aslinhasabaixo, para acertara escala antes da u lização.
VIKTIGT.Användintedenna mall om den skalats om genom
utskri ellerkopiering.Om de ainte är originalet eller en
utskri frånenPDF,kontrollera a linjerna nedan stämmer
medskalaninnan det används.
IMPORTANTE.Nonu lizzarequestomodello se è stato
ridimensionatocopiandoloo stampandolo. Se questo non è
l’originaleolastampa di un le PDF, vericare se le linee che
seguonodevonoessere dimensionate prima di essere u lizza-
te.
TÄRKEÄÄ.Äläkäytätätä kaaviota, jos sen mi akaavaon
muu unutkopio-idessatai tulostaessa.Jos tämä ei ole alku-
peräinentaiPDF tuloste tarkistarajat mi akaavastaalla
ennenkäy öä.
注意：请尽量不要使用本安装挖孔尺寸模版图的复印件。
如果使用复印件，则在使用之前请确认其比例一定要与原
件大小必须一致。
중요: 복사나 출력으로 크기가 조정 된 경우 이 템플릿을
사용하지 마십시오. 원본이 아니거나 인쇄물이면,
사용하기 전 아래 치수선의 눈금을 확인 해 주십시오.
注：このテンプレートは印刷やコピーによって縮尺が変
わっていることがありますので使用しないで下さい。テ
ンプレートがオリジナルのものでない場合には、下の寸
法線を使って縮尺を確認してください。
ВНИМАНИЕ: Не используйте эту инструкцию, ес
ли она была изменена в размерах при копирова
нии или распечатке. Если вы используете не ор
игинал, а распечатку из файла, убедитесь в соо
тветствии размеров линейки в нижней части и
нструкции с действительными размерами.
Checkdimensions before cutting
12"
300mm
L
C
L
C
192.5mm (7.58")
186.0mm (7.32")
192.5mm (7.58")
186.0mm (7.32")
200.0mm (7.87")
117.5mm (4.63")
111.0mm (4.37")
130.0mm (5.12")130.0mm (5.12")
117.5mm (4.63")
111.0mm (4.37")
200.0mm (7.87")
385.0mm (15.16")
372.0mm (14.65")
400.0mm (15.75")
235.0mm (9.25")
222.0mm (8.74")
260.0mm (10.24")
MO16
Marine Monitor
X4
1
3
x4
x2
4
CLICK
5
6
7
2
2. Tape appropriate mounting template
in place on dash, and ensure cutout
lines are level relative to a reference
point on dash.
3. Drill top and bottom mounting
screw holes using an appropriate drill
bit for the surface material:
• Soft materials e.g. Plywood - 1.9 - 2.3
mm (5/64”)
• Hard materials e.g. GRP, Acrylic,
hardwoods - 2.3 - 2.5 mm (3/32”)
4. Drill cutout corners with a small pilot
drill bit followed with 13 mm drill
bit. Complete cutout with jigsaw or
similar tool.

| 9
Display installation | MO Series User Manual
5. Place the display in the dash hole.
6. Place the guide tool on the glass of the display.
7. Slide the tool across so the drill bit hole guide lines up with the center of a screw
location hole on the case of the display.
8. Drill the pilot hole.
¼Note: Before drilling the rest of the pilot holes it is recommended to secure the
display with at least one screw to allow for movement in the dash cutout.
9. Insert one of the supplied screws in to the screw guide and tighten using a hand
screw driver.
10. Repeat for the rest of the mounting screws.
11. Wind wing nut on to wing screw,
then wind the wing screw assembly
in to bracket till approximately 5 mm
of threaded rod protrudes through
other side of bracket.
12. Fit stopper foot on to end of wing
screw.
13. Complete for both threaded holes on
each bracket.
14. Fit brackets to rear of display, aligning
‘key holes’ on bracket with screws on
back of display case.

10 |Display installation | MO Series User Manual
CLICK
15. With bracket making contact with
back of monitor, slide bracket down
till it engages with a click and is held
in place.
16. Wind in the wing screw, until
stoppers make rm contact with rear
of dashboard material.
17. Check front of unit, ensuring that
unit’s bezel is making even contact
with the dash surface.
18. Hand tighten wing nuts against the
back of the mounting brackets to
lock the wing screw in place. Hold
wing screw stationary if it turns while
adjusting the wingnut.
19. When tting bezels, ensure hook
tabs on back of each bezel recess
into opposing slots on screen frame.
Once ush with front surface of
screen, slide top bezel to the left, and
bottom bezel to the right to lock in
to place.