SImx LHT0214 User manual

Model: Flood LED
INSTALLATION INSTRUCTIONS
IMPORTANT
Thank you for purchasing this SIMX floodlight. This luminaire is suitable
for outdoor permanent use and requires a 220V-240V AC power supply.
Please read this manual thoroughly before installation and retain for
future reference.
Flood LED 30W LHT0214 Flood LED 55W LHT0215
Lamp Wattage 30watts Lamp Wattage 50watts
Current load 0.16A Current load 0.26A
Power Factor 0.92 Power Factor 0.94
LED type OSRAM OSLON® Square LED type OSRAM OSLON® Square
Luminaire Efcacy 79.9 lm/w Luminaire Efcacy 71.3 Im/w
Imax Intensity 953cd Imax Intensity 1337cd
FLOOD LED - BOTH MODELS
Voltage 220V - 240V AC Light beam angle 100° to ½ peak intensity
Weight 2.25 kg (approx) Color temperature 5700k
Working
temperature -20°C to + 40°C CRI (Ra) 70
Ingress Protection IP65 TM21 L70 L70 (12k) > 56000hrs
Construction Cast Alloy housing, tempered glass, stainless steel external xations
CB
A
Dimensions
A = 276mm height
B = 64mm depth
C = 220 width
TECHNICAL SPECIFICATIONS
This product is suitable for use only with a supply voltage of 220-240V AC 50Hz.
All electrical work must be carried out in accordance with local and national electrical codes as applicable.
We strongly recommend that this light fitting is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed on the
circuit for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
This light fitting is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Young children should
be supervised to ensure that they do not play with the appliance.
Any changes or modifications made or attempted to this product, without the prior written approval of the
manufacturer, will void any and all stated warranties.

Distributed by: Simx Limited
Ph: [phone] | Technical Support Ph: [phone]
Email: [email protected] | www.simx.co.nz
MANUFACTURERS EXTENDED WARRANTY
PRODUCT COMPLIANCES
Product is compliant with: AS/NZS60598.1:2003 AS/NZS60598.2.5:1998 EN55015:2006 EN61000.3.2:2006
EN61000.3.3:2008 IEC61347.1:2007 EN61547:2009 IEC61347.2.13:2006 EN62471:2008
and relevant amendments
This product is guaranteed by SIMX Ltd for 36 MONTHS from the date of purchase against faulty materials or
workmanship which affects its designed ability to operate. During this period if the product has a
defect of this nature it will be repaired or replaced free of charge by SIMX with the same item,
or a similar item, or a similar one of higher specication. ON CONDITION THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user. ie a receipt/sales invoice is produced as proof of purchase
The product has not been misused or handled carelessly, installed in anyway contrary to the installation
instructions, or installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable parts.It does not
confer any rights other than those expressly set out above and does not cover any claims for consequential
loss or damage.
Our Goods come with guarantees that cannot be excluded under the Australian and New Zealand Consumer
law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced
if the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
INSTALLING YOUR LED FLOODLIGHT
This light fitting is rated to IP65 and suitable for permanent outdoor use. Ensure the desired location does not
exceed this rating. When directing this floodlight at a wall or object, a minimum distance of 1 metre must be
observed. Suitable orientations for mounting this floodlight are shown below.
NOTE: This floodlight must be installed by a Registered Electrical Contractor.
Switch off the power supply before commencing all electrical work. Remove stirrup from the floodlight and
mount the stirrup securely through 2 fixing points, to wall or permanent structure. Resecure floodlight to
the stirrup. Aim the floodlight and torque the fixing bolts to 5nm.
WARNING: Floodlight must Not be mounted within exposed areas where wind gusts are
expected beyond 130kmph.
Terminate cable correctly inside an independently mounted IP65 enclosure. Failure to ensure correct
polarity of cabling will result in irrepairable lamp failure. Restore AC power to test.
For Wiring Installation:
Brown = LIVE Blue = NEUTRAL Green/Yellow = EARTH
To avoid unnecessary spill light or glare to neighbours and/or to passing pedestrians or vehicles,
care and consideration should be taken when mounting this floodlight.
Pub1236 iss03 05/16
Simx reserves the right to alter technical specications without prior warning