SImx LHT1054 User manual

MANUAL CONTROL (Override Function)
• When power is first switched on, the PIR detector enters into the “WARM-UP” period for about 1
minute, then automatically switches into AUTO mode.
• Turning the wall switch off and on twice, within 3 seconds, will change from AUTO mode to MANUAL
mode.
• In MANUAL mode, the lamp(s) will remain ON, not affected by duration time and LUX control settings,
after 8 hours, the lamp will change to AUTO mode again.
• To change it back to AUTO mode, prior to this, turn the wall switch off and on twice in about 3 seconds
(the same override used to go from AUTO to MANUAL mode).
• During MANUAL mode or AUTO mode, by switching off the ON/OFF main switch within 6 seconds and
then on again, the PIR detector will reset to WARM-UP period. TECHNICAL SPECIFICATIONS
Power Source 220-240V AC
Detection Range 10m max, 150°
Time Setting Min: 10 sec ± 5 sec
Max: 4 min ± 1 min
Dusk Control Day to night (adjustable)
PIR Aiming adjustment Pan/tilt
Sensitivity Control Yes
Manual Override Yes
Standby Power <1W (sensor head only)
Rated Load 20W
Lumens 3000K 1800 lumens
by Colour Temp 4000K 2000 lumens
5000K 2000 lumens
IP Rating IP54
Safety Class II
Mounting Ceiling or wall
Construction UV-stabilised polycarbonate
ECOSPOT SELECT
TWIN 10W LED SENSOR LIGHT
LHT1054 BLACK / LHT1055 WHITE
Thank you for purchasing the Simx Lighting EcoSpot Select LED sensor light. This product is suitable for
sheltered exterior locations. It requires a 230V AC power supply to operate and should be installed by a
registered electrician. Please read this manual before installation and retain for future reference.
INSTALLATION INSTRUCTIONS
This product is suitable for use only with a supply voltage of 220-240V AC 50Hz.
All electrical work must be carried out in accordance with local and national electrical codes as
applicable. We strongly recommend that this light fitting is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed in
the circuit for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
This light fitting is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Young
children should be supervised to ensure that they do not play with the appliance.
Any changes or modifications made or attempted to this product, without the prior written approval
of the manufacturer, will void any and all stated warranties.
IMPORTANT
PUB1498 2009
Specifications are subject to change without notice
Distributed in New Zealand by Simx Ltd
Ph: [phone] | Technical Support Ph: [phone]
e: [email protected] | www.simx.co.nz
Distributed in Australia by Ventair Pty Ltd
4 Capital Place, Carrum Downs, 3201 VIC, AUSTRALIA.
Technical Support: 1300 665 926
e: [email protected] | www.ventair.com.au | www.simx.com.au
MANUFACTURERS EXTENDED WARRANTY
This product is guaranteed by SIMX Ltd and Ventair Pty Ltd for 3 years from the date of purchase against
faulty materials or workmanship which affects its designed ability to operate. During this period if the
product has a defect of this nature it will be repaired or replaced free of charge by SIMX with the same
item, or a similar one of higher specification.
ON CONDITION THAT:
• The buyer returns it to the seller from whom it was bought, freight paid.
• The product has been bought by the user (ie. a receipt/sales invoice is produced as proof of purchase).
• The product has not been misused or handled carelessly, installed in any way contrary to the
installation instructions, or installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for discolouration and/or delamination of paint or plastic, or any user
serviceable parts. It does not confer any rights other than those expressly set out above and does not
cover any claims for consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under either Australian, or New Zealand,
Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if
the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
PRODUCT COMPLIANCES
AS/NZS 60598.1:2017 AS/NZS 60598.2.1:2014 AS/NZS CISPR15:2017 EN61000.3.2:2014
EN61000.3.3:2013 EN55015.2013 EN62031.2015 EN62473.2015
AS/NZS 61347.1:2016 AS/NZS 61058.1:2008 and relevant amendments

BEFORE YOU START
Please read all the instructions prior to installation.
The EcoSpot Select should be wired to its own light switch. Do not interconnect with other lights on
the same switch, or on the same PIR sensor.
To achieve best results, please consider the following points:
• To avoid false triggering, the sensor should be directed away from heat sources such as barbecues,
air con, flue vents etc.
• Do not aim towards reflective surfaces such as smooth white walls, swimming pools, etc.
• Before selecting a place to install your Eco Spot Select, note that movement across the scan area
is more effective than movement directly toward or away from the sensor.
SETTINGS
The length of time the EcoSpot Select remains switched on after activation can be adjusted from
10 seconds (± 5 seconds) to 4 minutes (± 1 minute). Rotating the TIME knob to (+) or (-) will adjust the
duration time accordingly.
Note: Once the light has been triggered by the PIR sensor any subsequent detection will restart the
timed period.
The sensitivity means the maximum distance which PIR sensor can be triggered by motion. Adjusting the
SENS knob from (+) to (-) will adjust the sensitivity.
The LUX control module has a built-in sensing device (photocell) that detects daylight and darkness.
The () position indicates it will work at day and night, and in the () position - only at night. Set dial to
operate at the desired level by adjusting the LUX knob.
Setting up the sensor (refer to Fig. 2)
Turn the LUX control knob to light () position, turn the wall switch on and wait 30 seconds for the
control circuit to stabilise. Ensure that the TIME control is set at minimum.
Direct the sensor toward the desired area to be scanned by adjusting the elbow jointand swivel jointon
the sensor arm. Have someone move across the centre of the area to be scanned and slowly adjust the
angle of the sensor arm until the unit senses the movement and triggers as desired. Adjust SENS dial to
alter distance.
Adjust the TIME control to required setting.
If the lights are required to operate from dusk, wait for the desired light level, then slowly turn the LUX
control knob towards daylight while someone walks across the centre of the detection area. When the
lights switch on, release the LUX control knob. Set LUX control to suit your application.
Note: All PIR sensors are more sensitive in colder or dry weather than warmer weather.
You may need to make further adjustments to achieve your ideal light level setting. To avoid dust
build-up and ensure proper functioning of the EcoSpot Select, wipe the sensor lens lightly with a damp
cloth every 3 months.
Before any aiming adjustments, switch EcoSpot Select off and allow the hot lamp housings to cool.
When adjusting lamp housings, ensure they are not touching or in close proximity (not less than 40mm)
to sensor head, as heat from the lamp housing may impact operation of the PIR sensor.
Fig. 2
INSTALLATION
We strongly recommend this light fitting is installed by a registered electrician
• Switch off the power supply before commencing any electrical work.
• Unscrew the fixing cover screws and remove the rear cover.
• Use the rear cover to mark the position of screw holes onto mounting surface.
• Drill the wall to depth of about 4 cm and fit the wall plugs (supplied).
• Care should be taken to avoid drilling or screwing into concealed electrical wiring/plumbing.
• Push the cable through the cable gland. Affix the back of the housing to the mounting surface with
mounting wall screws.
• Connect the power cables to the terminal block securely (refer to Fig. 1). Refit the terminal block and
cable anchorage. Select lamp colour from internal dip switch (refer to Fig. 2).
• Reattach and screw securely the cover to the base. Ensure cables are not pinched in closing the unit.
• Reconnect mains power.
• Test circuit and setup PIR settings (see below).
Fig. 1
Selecting lamp colour with power supply connected
may cause irreparable damage. Always disconnect
at mains before making any colour selection. 10 Sec 4 Min 3 mtr 10 mtr
Night
Day
