SImx CHM0166 User manual

It is very important to install and operate this product according to
the following instructions.
INSTALLATION INSTRUCTIONS
SUNRISE PLUG-IN DIGITAL DOOR CHIME
Model No: CHM0166
Additional Door Presses: CHM0168 Black, CHM0169 White
Receiver
Indoor Chime Unit
Transmitter
Exterior Door Press

1
PRODUCT INSTRUCTION
Thank you for purchasing this Smix Sunrise Plug-in Digital Door Chime.
Simply plug the indoor chime to an AC outlet, mount the door press where
needed and you are ready to go! The indoor chime can be expanded to work
with up to 30 door presses or door chimes using a simple procedure in
10-15 seconds. Its working range is up to 100 metres in free air.
FEATURES
Easy to Install and Use
58 Musical Melodies
5 Level Adjustable Volume
Up to 100m Operating Range (free air)
Flashing Light Designed for Hearing Impaired
Expandable System - Just Add Door Presses
IP55 Waterproof Door Press

2
PACKAGE CONTENTS
Receiver, Transmitter, 3V CR2032 button battery, and mounting kit.
TECHNICAL SPECIFICATIONS
Receiver
Voltage: 220-240V AC
Wattage: <2.0 Watts
Working Frequency: 433.92 MHz
Sound dB(A): 25-85 dB(A)
Operating Range (Free Air): Up to 100m
Transmitter
Battery (included): CR2032
Working Power: < 10mW
Push Button Rating: IP55
Operating Temperature -20°C to + 50°C

Before fixing the products, check your desired locations can communicate
first. The product is rated to operating up to a range of 100 metres in free air.
The operating range will be reduced if the signal is transmitted through a
number of walls or ceilings.
NOTE: Common barriers to avoid completely include mounting to any metal
surface or UPVC door frames. Avoid positioning above heat sources such as
radiators, or in damp areas such as a kitchen or bathroom. Do not expose
either unit directly to rain or immerse in water. Do not locate either unit close
to fireplace or expose to high temperatures.
Note the Receiver is suitable for Indoor use only. The Transmitter is rated for
exposed exterior locations.
• The Receiver is plugged into a 230V power socket.
• Affix the door press to a smooth surface with double sided tape
and screws as required. Before you drill any hole in the wall, please make
sure there are not cables or pipes that you may accidentally damage.
3
SELECTING YOUR MOUNTING LOCATIONS
AFFIXING THE PRODUCTS

What is Auto-learning Code?
The Transmitter sends a wireless signal to the Receiver. The Receiver would
automatically register and memorize the signal as an operation code.
So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up - Operation for 1 Transmitter and 1 Receiver
• After battery installation of the Transmitter, Plug the Receiver into
a power socket.
• Firstly, select your desired melody. Factory default is ‘DING DONG’ sound.
• Then press and hold the Volume control button on receiver for
5 seconds. The Receiver will sound and light will flash,
indicating the device is ready to pair.
• Press the transmitter button once. Pairing will be confirmed by
playing of selected melody.
Expanding your system
You can pair up to 30 Transmitters to a single Receiver, by repeating steps
above for each additional Transmitter (one at a time). Use items CHM0168
or CHM0169 Transmitters.
NOTE: If you require a different melody for different Transmitters, select new
melody first before pairing. This may be useful for multiple entranceways to
know which doorway is being visited. Alternatively, an additional door press
may be used as a panic button.
4
SETUP THE AUTO-LEARNING CODE

There are 58 different melodies to select from. Scroll through these using the
forward/backward melody buttons on the side of the Receiver to select your
preferred melody. This can be changed at any time using the re-pairing steps.
There are 5 volume settings to select from. Scroll through these using the
volume button on the side of the Receiver for the appropriate volume for your
location. This can be changed at any time without re-pairing.
5
SELECTING YOUR PERSONAL SETTINGS
It is important to remember that when you replace the run-out battery with new
one that you may need to follow the same procedure of the auto-learning code
set-up as above.
NOTE: Interference from another similar door chime operating nearby: To reset
all settings, press the Music Forward Button for 5 seconds, then pairing will be
relieved and melody turn into the default music -Ding Dong.
Repeat steps above to re-pair.

6
STRUCTURE DIAGRAM
Product Diagram (Receiver)
Product Diagram (Waterproof Transmitter)
Volume Control
Music Backward
Music Forward
Speaker
AC Plug
Mount
Ridge Points Wall Bracket
Waterproof
Button
Open From
Here Screws

• Unscrew and lever the base off the top cover of the Transmitter.
There is a small slot at the base of the unit to facilitate this.
The base is held in place firmly, so some pressure may be required.
It will not break, rather will pop open.
• Remove the circuit board (it may be secured with a small screw).
Insert the supplied CR2032 into the battery holder, ensuring polarity of
battery on installation. Reinsert the circuit board.
• Close the Transmitter enclosure by setting the fastening tab of the top
cover into the slot on the base. Then carefully press the base into the
top cover. It should click neatly into place, ensuring the waterproof
rating of the Transmitter is maintained. Resecure base with screws.
7
INSTALLING THE BATTERIES
Battery Slot
Battery
Push Button
Screws

Press the push button on the Transmitter unit once, it sends a wireless
signal to the Receiver which will play the selected melody. The sound
will stop as soon as the melody ends. For repeat sound, press the button
again. Holding the Transmitter button IN will NOT repeat the sound.
If the Receiver does not sound, please check the following:
• Flat batteries in the Transmitter -change the battery.
• Wrong battery polarity in the Transmitters-reinsert the battery.
• Units are out of range-relocate the Receiver within the operation range.
• Receiver has come unplugged from wall socket – plug in again.
• If leaving the chime unused for long periods, remove the battery
from Transmitter to prevent leakage.
• Dispose of old batteries in accordance with the relevant legislation.
8
OPERATION
USER HINTS

This product complies to all relevant NZ/AU compliance standards.
An SDOC (supplier compliance declaration) is available on www.simx.co.nz
Type the product code into Search on the home page, this takes you to
the item product page, a download link is located below the product details
on that page.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE WHEN REPLACING BATTERIES
ELECTRICAL COMPLIANCE
Distributed by: Simx Limited
Ph: [phone] | Technical Support Ph: [phone]
Email: [email protected] | www.simx.co.nz
PUB1712 2111
Specifications are subject to change without notice.