Sinoboom 1323RD User manual

1323RD/4389RD
1623RD/5389RD
Maintenance
Manual
Part No.502013110002
Rev: B
Mar. 2022
GTJZ
0608E (2132E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
长沙市宁乡高新技术产业园区金洲大道东
128 号
0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn
Al w ays F or B e t t er A cc ess Solution s
我们一直在追求新的高 度
尺寸 ：
210×285mm
20mm
20mm
产品说明书
PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or
equipment can expose you to chemicals including engine
exhaust, carbon monoxide, phthalates, and lead, which
are known to the State of California to cause cancer and
birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your vehicle or equipment in
a well-ventilated area and wear gloves or wash your
hands frequently when servicing. For more information
go to: www.P65warnings.ca.gov.
For disposal, please follow your nation regulation.

Please contact us:
Website : www.sinoboom.com
E-mail : [email protected]
Sales Tel : [phone]
Service Tel : [phone]
Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,
Hunan, China
Zip Code : 410600
Copyright © Hunan Sinoboom Intelligent Equipment Co., Ltd. All Rights Reserved
The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.
Manual revision history:
REV DATE DESCRIPTION REMARK
AJul, 2021 Original issue of the manual
B Mar, 2022 Updated manual, added Yanmar engine information

APPLICATION
Use the following table to identify the specific serial number for models included in this manual. Check
the model of your machine before consulting the manual, and then use the correct manual according to
the serial number of the model. See the nameplate on your machine to identify the model and serial
number. (See Decals/Nameplate Inspection of the Operation Manual for details.)
Models
Trade Identification
Serial Numbers
Metric Imperial
1323RD 1323RD 4389RD 0201200100 to present
1623RD 1623RD 5389RD 0201300109 to present
NOTE:
•Product model is applied in product nameplate for distinction of products of different main
parameters.
•Product trade identification is applied in marketing and machine decals for distinction of products of
different main parameters, and can be classified as metric type and imperial type: The metric trade
identification is applicable to machines for countries/regions using metric system or as specially
required by customers; The imperial trade identification is applicable to the machines for countries/
regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS
Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the
latest product manual information to the website www. sinoboom. com as soon as possible. However,
due to continuous product improvement, the information in this manual is subject to change without prior
notice.
This manual covers the basic parts information of one or more products. Therefore, please use this
manual according to your needs. If you find problems in the manual or have suggestions for improve-
ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as
possible.
Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the
products you need online at www.sinoboom.com.
Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.
All of the above are registered trademarks of Hunan Si-
noboom Intelligent Equipment Co., Ltd..

This Page Intentionally Left Blank

1323RD&1623RD MaintenanceManual i© Mar. 2022
TABLE OF CONTENTS
Introduction ..............................v
1 Specifications .................... 1-1
Machine Specifications . . . . . . . . . . . . . . . 1-1
Major Component Weights. . . . . . . . . . . . 1-5
Engine Specifications . . . . . . . . . . . . . . . . . 1-6
Power System Specifications . . . . . . . . . 1-7
Hydraulic Hose and Fitting
Specifications . . . . . .. . . . . . . . . . . . . . . . . . . 1-8
Hydraulic Hose Torque . . . . . . . . . . . . . 1-8
Hydraulic Fitting Torque . . . . . . . . . . . . 1-8
Hydraulic Hose and Fitting Tight-
ening Procedure . . . . . . . . . . . . . . . . . . . 1-11
Fastener Torque Specifications . . . . . . 1-11
2 Safety............................... 2-1
Safety Definitions . . . . . . . . .. . . . . . . . . . . . 2-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 2-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 2-2
Tipping Hazards and Rated Load . . . . . 2-2
Work Environment Hazards . . . . . . . . . . . 2-4
Unsafe Operation Hazards. . . . . . . . . . . . 2-5
FallHazards...........................2-6
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 2-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Explosion and Fire Hazards. . . . . . . . . . . 2-8
Damaged Machine Hazards . . . . . . . . . . 2-8
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 2-9
Battery Hazards . . . . . . . . . . . . . . . . . . . . . . . 2-9
Hydraulic Systems Hazard . . . . . . . . . . . 2-11
Welding and Polishing Requirements 2-11
After Using the Machine. . . . . . . . . . . . . .2-12
3 System Descriptions............ 3-1
Power System. . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Hydraulic System . . . . . . . . . . . . . . . . . . . . . 3-1
Electrical System. . . . . . . . . . . . . . . . . . . . . . 3-1
Machine Control. . . . . . . . . . . . . . . . . . . . . . . 3-1
Safety Measures . . . . . . . . . . . . . . . . . . . . . . 3-1
4 Service and Guidelines......... 4-1
Machine Preparation, Inspection and
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
General.............................4-1
Preparation, inspection and
maintenance . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Qualified Sinoboom equipment
mechanic ...........................4-1
Pre-operation inspection. . . . . . . . . . . . 4-1
Pre-delivery inspection and
frequent inspection . . . . . . . . . . . . . . . . . 4-1
Annual machine inspection . . . . . . . . . 4-1
Preventive maintenance . . . . . . . . . . . . 4-2
Storage .............................4-3
Maintenance and Servicing
Precautions ...........................4-3
General.............................4-3
Safety and workmanship . . . . . . . . . . . 4-3
Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Component removal and installation4-4
Component disassembly and
assembly ...........................4-4
Scrap of structural parts . . . . . . . . . . . . 4-4
Pressure-fit parts . . . . . . . . . . . . . . . . . . . 4-5
Bearings ............................4-5
Gaskets.............................4-5
Bolt usage and torque application . . 4-5
Hydraulic lines and electrical wiring 4-5
Hydraulic system . . . . . . . . . . . . . .. . . . . 4-5
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Battery..............................4-5
Pins and composite bearing. . . . . . . . . . . 4-5

© Mar. 2022 ii 1323RD&1623RD MaintenanceManual
Application of Insulating Silicone
Grease to Electrical Connections . . . . . 4-6
5 Maintenance ...................... 5-1
Conducting a Pre-delivery Inspection . 5-1
Following a Maintenance Schedule . . . 5-2
Completing a Repair & Inspection
Report.................................5-2
Major Modification and Repair Record 5-5
Checklist A Procedures . . . . . . . . . . . . . . . 5-6
A-1 Inspect All Manuals. . . . . . . . . . . . . 5-6
A-2 Inspect All Decals . . . . . . . . . . . . . . 5-6
A-3 Inspect Damaged, Loose or
LostParts...........................5-6
A-4 Inspect Hydraulic Oil Level . . . . . 5-7
A-5 Inspect Hydraulic Leakage . . . . . 5-7
A-6 Inspect Fuel Level . . . . . . . . . . . . . . 5-7
A-7 Inspect Fuel Leakage . . . . . . . . . . 5-9
A-8 Inspect Engine Oil Level. . . . . . . . 5-9
A-9 Inspect Engine Intake System.5-10
A-10 Inspect Engine Belt . . . . . . . . . .5-10
A-11 Inspect Fuel Filter (Fuel-
Water Separator) . . . . . . . . . . . . . . . . . .5-10
A-12 Inspect Cooling Fan. . . . . . . . . . 5-11
A-13 Inspecting Coolant Level
（Water-cooled Engine）. . . . . . . . . .5-12
A-14 Functional Tests. . . . . . . . . . . . . .5-13
A-15 Perform Maintenance after
30 Days............................5-18
Checklist B Procedures . . . . . . . . . . . . . .5-18
B-1 Inspect Electrical Wiring . . . . . . .5-18
B-2 Inspect Rim, Tire and
Fasteners..........................5-19
B-3 Inspect Hydraulic Oil . . . . . . . . . .5-19
B-4 Inspect Cooling System . . . . . . .5-19
B-5 Replace Fuel filter Element
(Fuel-Water Separator) . . . . . . . . . . . .5-20
B-6 Inspect Air filter of Hydraulic
Tank ...............................5-21
B-7 Replace High-Pressure Filter
Element............................5-21
B-8 Replace Engine Air Filter
Element............................5-22
B-9 Inspect the Battery . . . . . . . . . . . .5-23
B-10 Inspect Engine Exhaust
System.............................5-24
B-11 Inspect Drive Reducer Oil
Level...............................5-24
B-12 Test Oscillate Outriggers . . . . .5-24
B-13 Test Drive Speed. . . . . . . . . . . . .5-25
B-14 Test Tilt Protection System . . .5-25
B-15 Test Brake Distance. . . . . . . . . .5-26
Checklist C Procedures . . . . . . . . . . . . . .5-26
C-1 Replace Fuel Filter Element. . .5-26
C-2 Replace Engine Oil. . . . . . . . . . . .5-27
C-3 Replace Engine Oil Filter . . . . . .5-28
C-4 Test Weighing System. . . . . . . . .5-29
C-5 Inspect Carbon Brush of Motor5-30
C-6 Inspect Raising Limit Switch . .5-30
C-7 Inspect Staged Lowering . . . . . .5-31
Checklist D Procedures . . . . . . . . . . . . . .5-31
D-1 Replace Drive Reducer Gear
Oil..................................5-31
D-2 Inspect Scissor Arm Sliders . . .5-31
D-3 Replace Hydraulic Oil . . . . . . . . .5-32
D-4 Replace Hydraulic Tank
Suction Filter. . . . . . . . . . . . . . . . . . . . . . .5-32
D-5 Inspect Scissor Arm Bearings .5-33
6 Repair............................... 6-1
Platform Components . . . . . . . . . . . . . . . . . 6-1
Platform Controller. . . . . . . . . . . . . . . . . . 6-1
Platorm Assembly . . . . . . . . . . . . . . . . . . 6-1
Extension Platform . . . . . . . . . . . . . . . . . 6-2
Scissor Components . . . . . . . . . . . . . . . . . . 6-2
Scissor Arm Assembly. . . . . . . . . . . . . . 6-2
Lift Cylinder . . . . . . . . . . . . .. . . . . . . . . . . . 6-3
Chassis Components . . . . . . . . . . . . . . . . . 6-4
Tires and Rims. . . . . . . . . . . . . . . . . . . . . . 6-4

1323RD&1623RD MaintenanceManual iii © Mar. 2022
Reducer and Drive Motor . . . . . . . . . . . 6-5
Steer Cylinder . . . . . . . . . . . . . . . . . . . . . . 6-5
Steer Linkage . . . . . . . . . . . . . . . . . . . . . . . 6-6
Oscillate Cylinder . . . . . . . . . . . . . .. . . . . 6-6
Ground Controller. . . . . . . . . . . . . . . . . . . 6-7
Hydraulic System . . . . . . . . . . . . . . . . . . . . . 6-8
Layout of Hydraulic Elements. . . . . . . 6-8
Hydraulic Tank . . . . . . . . . . . . . . . . . . . . . . 6-9
Hydraulic Pump. . . . . . . . . . . . . . . . . . . . . 6-9
Function Valves. . . . . . . . . . . . . . . . . . . . 6-11
Regulating Hydraulic Valve
Pressure...........................6-17
Hydraulic Symbols . . . . . . . . . . . . . . . . .6-20
Hydraulic Schematic . . . . . . . . . . . . . . .6-21
Electrical System. . . . . . . . . . . . . . . . . . . . .6-22
DTC Control System. . . . . . . . . . . . . . .6-22
Sinoboom Control System . . . . . . . . .6-26
Fault Code Description . . . . . . . . . . . .6-31
Use and Maintenance of Battery. . .6-35
Electrical Symbols . . . . . . . . . . . . . . . . .6-37
Electrical Schematic . . . . . . . . . . . . . . .6-39
Appendix 1: Prepare the Work
Record Before Delivery ....... A-1
Appendix 2: Repair & Inspection
Report .............................A-3
Appendix 3: Major Modification
and Repair Record ............. A-7

© Mar. 2022 iv 1323RD&1623RD MaintenanceManual

1323RD&1623RD MaintenanceManual v© Mar. 2022
INTRODUCTION
Thank you for choosing and using the machinery of
Hunan Sinoboom Intelligent Equipment Co., Ltd. Al-
ways read, understand and become familiar with the
operation requirements of the machine and its associ-
ated safety procedures before operating, maintaining
and repairing the machine. Operating the machine with-
out becoming familiar with its specific operation require-
ments and safety procedures poses serious risks.
Operators who follow safety rules and operate the ma-
chine carefully and effectively will prevent personal in-
jury, property loss and accidents.
Use this machine only to transport tools to work loca-
tions and for performing tasks on the work platform. Op-
erators must be competent and must obtain training to
carefully use the machine and follow safety procedures.
Only trained and authorized personnel may operate the
machine.
This manual guides the operator and authorized per-
sonnel in maintaining the machine. The operator is re-
sponsible for reading, understanding and implementing
the maintenance and safety procedures in this manual
and for following the manufacturer’s instructions before
beginning any work. Read, understand and follow all
safety rules and operating instructions. The operator
must also consider the machine’s uses and limitations
and the conditions at the jobsite before using this ma-
chine. Strictly following all safety requirements in this
manual is critical.
Consider this manual a part of the machine, along with
Operation Manual and Parts Manual, and always keep
the manuals with the machine. The owner or adminis-
trator of the machine shall offer all manuals and other
necessary information provided by the machine manu-
facturer regarding the daily inspection and maintenance
to each of the renters. If the machine is sold, the owner
or administrator must pass along the manuals and other
necessary information to the purchaser. The owner or
administrator of the machine shall also provide the
manufacturer’s maintenance information to the person
responsible for maintaining the machine.
If you have any questions, contact Hunan Sinoboom In-
telligent Equipment Co., Ltd..

© Mar. 2022 vi 1323RD&1623RD MaintenanceManual
This Page Intentionally Left Blank

1323RD&1623RD MaintenanceManual 1-1 © Mar. 2022
1SPECIFICATIONS
MACHINE SPECIFICATIONS
Table 1-1 1323RD specifications
MEASURE 1323RD (METRIC) 4389RD (IMPERIAL)
DIMENSIONS
Max. platform height 13.1 m 42ft 11.7in
Max. working height 15.1 m 49ft 6.5in
Max. horizontal reach (rear
extension platform extended) 1.2 m 3ft 11.2in
Max. horizontal reach (front
extension platform extended) 1.5 m 4ft 11.1in
Overall length 4.88 m 16ft
Overall width 2.28 m 7ft 5.7in
Overall height (stowed, rails folded) 2.22 m 7ft 3.4in
Overall height (stowed, rails up) 2.98 m 9ft 9.3in
Wheelbase 2.84 m 9ft 3.8in
Wheel span 1.95 m 6ft 4.7in
Ground clearance 0.36 m 1ft 2.2in
Tire size (diameter × width / type) 33×12-20/solid 315/55D20/foam-filled
Platform dimension (Length × Width
× Height)-6.5 m Platform 3.96 m×1.82 m×1.1 m 13ft×6ft×3ft 7in
Platform dimension (Length × Width
× Height)-7.4 m Platform 4.84 m×1.82 m×1.1 m 15ft 10.6in×6ft×3ft 7in
PERFORMANCE
Rated platform capacity 680 kg 1499 lb
Individual extension platform
capacity 227 kg 500 lb
Max. platform occupancy 7 persons
Drive speed (stowed) 0～6.1 km/h 0～3.8 mph
Drive speed (raised) 0～1.1 km/h 0～0.68 mph
Up time (no load) 40～50 s
Down time (no load) 34～44 s
Gradeability 50% (26.6°)

© Mar. 2022 1-2 1323RD&1623RD MaintenanceManual
SPECIFICATIONS
MEASURE 1323RD (METRIC) 4389RD (IMPERIAL)
Max. allowable inclination (front-to-
back) 3°
Max. allowable inclination (side-to-
side, outrigger retracted/extended) 2°/0.8°
Max. outrigger leveling angle (front-
to-back) 7°
Max. outrigger leveling angle (side-
to-side) 12°
Turning radius (inside) 2.2 m 7ft 2.6in
Turning radius (outside) 5.3 m 17ft 4.7in
Max. allowable side force 400 N 90 lbf
Max. operating noise 86 dB
POWER
Drive mode (drive×steer) 4WD×2WS
Engine (rated power, RPM)
36.3 kW, 2800 rpm (Deutz D2011 L03i)
35.5 kW, 3000 rpm (Yanmar 4TNV88C-DFLT)
36.4kW, 3000 rpm (Yanmar 4TNV88-BDFLTC)
35.3kW, 3000 rpm (Yanmar 4TNV88-ZCDCSI)
Fuel tank capacity 110 L 24 gal (UK)/29 gal (US)
Hydraulic tank capacity 140 L 30.8 gal (UK)/37 gal (US)
Hydraulic system pressure 24 MPa 3481 psi
Battery specification (voltage,
capacity, rate of discharge) 12 V, 110 Ah, 5 hr
Power system voltage 12 VDC
System control voltage 12 VDC
GROUND BEARING INFORMATION
Max. tire load 3900 kg 8598 lb
Tire contact pressure 720 kPa 104 psi
Max. outrigger load 3200 kg 7055 lb
Outrigger contact pressure 630 kPa 91 psi
ENVIRONMENT
Max. allowable wind speed (indoor) 0 m/s 0 mph
Max. allowable wind speed
(outdoor)
12.5 m/s 28 mph
Max. allowable altitude 1000m 3280.8ft
Allowable ambient temperature
(lead-acid batteries) -10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium batteries) -20℃～40℃-4℉～104℉

SPECIFICATIONS
1323RD&1623RD MaintenanceManual 1-3 © Mar. 2022
MEASURE 1323RD (METRIC) 4389RD (IMPERIAL)
Max. allowable ambient relative
humidity 90%
Storage condition
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment
with 90% relative humidity (20℃[68℉]), and away from rain, sun,
corrosive gas, inflammables and explosives.
WEIGHT
Total weight 7700 kg 16976 lb
Table 1-2 1623RD specifications
MEASURE 1623RD (METRIC) 5389RD (IMPERIAL)
DIMENSIONS
Max. platform height 16.2 m 53ft 1.8in
Max. working height 18.2 m 59ft 8.5in
Max. horizontal reach (rear
extension platform extended) 1.2 m 3ft 11.2in
Max. horizontal reach (front
extension platform extended) 1.5 m 4ft 11.1in
Overall length 4.88 m 16ft
Overall width 2.28 m 7ft 5.7in
Overall height (stowed, rails folded) 2.44 m 8ft
Overall height (stowed, rails up) 3.21 m 10ft 6.3in
Wheelbase 2.84 m 9ft 3.8in
Wheel span 1.95 m 6ft 4.7in
Ground clearance 0.36 m 1ft 2.2in
Tire size (diameter × width / type) 33×12-20/solid 315/55D20/foam-filled
Platform dimension (Length × Width
× Height)-6.5 m Platform 3.96 m×1.82 m×1.1 m 13ft×6ft×3ft 7in
Platform dimension (Length × Width
× Height)-7.4 m Platform 4.84 m×1.82 m×1.1 m 15ft 10.6in×6ft×3ft 7in
PERFORMANCE
Rated platform capacity 680 kg 1499 lb
Individual extension platform
capacity 227 kg 500 lb
Max. platform occupancy 4 persons
Drive speed (stowed) 0～6.1 km/h 0～3.8 mph
Drive speed (raised) 0～1.1 km/h 0～0.68 mph
Uptime (no load) 70 s～90 s

© Mar. 2022 1-4 1323RD&1623RD MaintenanceManual
SPECIFICATIONS
MEASURE 1623RD (METRIC) 5389RD (IMPERIAL)
Downtime (no load) 45 s～55 s
Gradeability 40% (22°)
Max. allowable inclination (front-to-
back) 3°
Max. allowable inclination (side-to-
side, outrigger retracted/extended) 2°/0.8°
Max. outrigger leveling angle (front-
to-back) 7°
Max. outrigger leveling angle (side-
to-side) 12°
Turning radius (inside) 2.2 m 7ft 2.6in
Turning radius (outside) 5.3 m 17ft 4.7in
Max. allowable side force 400 N 90 lbf
Max. operating noise 86 dB
POWER
Drive mode (drive×steer) 4WD×2WS
Engine (rated power, RPM)
36.3 kW, 2800 rpm (Deutz D2011 L03i)
35.5 kW, 3000 rpm (Yanmar 4TNV88C-DFLT)
36.4kW, 3000 rpm (Yanmar 4TNV88-BDFLTC)
35.3kW, 3000 rpm (Yanmar 4TNV88-ZCDCSI)
Fuel tank capacity 110 L 24 gal (UK)/29 gal (US)
Hydraulic tank capacity 140 L 30.8 gal (UK)/37 gal (US)
Hydraulic system pressure 24 MPa 3481 psi
Battery specification (voltage,
capacity, rate of discharge) 12 V, 110 Ah, 5 hr
Power system voltage 12 VDC
System control voltage 12 VDC
GROUND BEARING INFORMATION
Max. tire load 3900 kg 8598 lb
Tire contact pressure 720 kPa 104 psi
Max. outrigger load 3200 kg 7055 lb
Outrigger contact pressure 630 kPa 91 psi
ENVIRONMENT
Max. allowable wind speed (indoor) 0 m/s 0 mph
Max. allowable wind speed
(outdoor)
12.5 m/s 28 mph
Max. allowable altitude 1000m 3280.8ft

SPECIFICATIONS
1323RD&1623RD MaintenanceManual 1-5 © Mar. 2022
MEASURE 1623RD (METRIC) 5389RD (IMPERIAL)
Allowable ambient temperature
(lead-acid batteries) -10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium batteries) -20℃～40℃-4℉～104℉
Max. allowable ambient relative
humidity 90%
Storage condition
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment
with 90% relative humidity (20℃[68℉]), and away from rain, sun,
corrosive gas, inflammables and explosives.
WEIGHT
Total weight 8780 kg 19357 lb
NOTE:
a) The platform height plus the operator height (taken as 2m [6ft 7in]) is the working height.
b) In different areas, hydraulic oil, engine oil, coolant, fuel and lubricant should be added in accordance with the
environmental temperature.
c) In cold weather, auxiliary devices are needed to start the machines.
d) The ground bearing data is approximate, not considering different options and only applicable when it is safe
enough.
e) The loads of persons, accessories, tools and materials are factored into the rated platform capacity.
f) The total vibration value of the platform does not exceed 2.5m/s², and the maximum root-mean-square value of
the weighted acceleration of the entire machine does not exceed 0.5m/s².
g) The hydraulic tank capacity is the maximum volume in the hydraulic tank.
MAJOR COMPONENT
WEIGHTS
UNSAFE OPERATION HAZARD
• Do not move heavy
components without
mechanical assistance.
• Do not place heavy
components upon instable
surfaces.
Table 1-3
Component Metric (kg) Imperial (lb)
Chassis assembly 3632 8007
Reducer and motor 59 130
Steer cylinder 8 18
Outrigger cylinder 69 152
Oscillation cylinder 12 26

© Mar. 2022 1-6 1323RD&1623RD MaintenanceManual
SPECIFICATIONS
Component Metric (kg) Imperial (lb)
Tire 161 355
Steer disc 25 55
Left door assembly 285 628
Right door assembly 380 838
Battery 26 57
Power unit 20 44
Scissor assembly 3155 6956
Lift cylinder, upper 124 273
Lift cylinder, lower 262 578
Engine (Deutz D2011 L03i) 244 538
Engine (Yanmar 4TNV88C-DFLT) 267 589
Engine (Yanmar 4TNV88-BDFLTC) 190 419
Engine (Yanmar 4TNV88-ZCDCSI) 199 439
Platform (6.5m Platform) 940 2072
Platform (7.4m Platform) 1057 2330
Note: the component weight may vary with different options of the machine selected.
ENGINE SPECIFICATIONS
Table 1-4 Deutz D2011 L03i
Type In-line, air-cooled, 4–stroke
Number of
Cylinders 3
Bore 94mm (3.7 in)
Stroke 112mm (4.4 in)
Total
Displacement
1.123L
0.25 gal (UK)
0.3 gal (US)
Compression
Ratio 19：1
Firing Order 1-2-3
Output 36.3kw@2800rpm
Torque 137Nm (101 ft-lb)@1700rpm
Low IdleSpeed 1600rpm
Alternator 14V-60A
Table 1-5 Yanmar 4TNV88C-DFLT
Type In-line, water-cooled, 4–stroke
Number of
Cylinders 4
Bore 88mm (3.46 in)
Stroke 90mm (3.54in)
Total
Displacement
2.189L
0.48 gal (UK)
0.58 gal (US)
Compression
Ratio 19.1：1
Firing Order 1-3-4-2
Output 35.5kW@3000rpm
Low RPM 3150rpm
High RPM 800rpm
Generator
capacity 12V-55A