Sinope RM3250ZB-C4 User manual

ON
Power
Controller placement
To facilitate connection to the network, choose a clear area. Do
not, for example, place the controller behind a water heater.
When you have selected a suitable area, select 1 or 2 with the
selection switch depending on the wiring of the device.
Install your controller
RM3250ZB-C4
Smart Electrical
Load Controller
Installation
Guide
2
Turn OFF the circuit at
the main electrical panel.
Secure the template
(included) behind the
wire.
Mark the anchorage
holes on the wall and the
positions where to cut
and unsheathe on the
wire.
Warning
This product is only compatible with the Control4 home
automation system.
The installation of this controller should be made by a certified
electrician and must be installed in conformity with the national and
local Electrical Codes.
Your controller RM3250ZB-C4
 Indicator / Button
The indicator lights up
when the controller is
connected to the network.
“ ”ON Indicator
The indicator lights up
when the load is ON.
“ower”P Indicator
The indicator lights up
when the controller is
powered.
5
Main Button
Press once to activate or deactivate the load.
Close the cover
and power up the
controller.
Note: The “Power”
indicator will lit.
If not, verify the
position of the wiring
selection switch (see
page 2).
Option 2
Load
Line
Option 1
Line
Load
1
RM3250ZB
CAUTION
DISCONNECT POWER BEFORE OPENING
AVERTISSEMENT
COUPER L’ALIMENTATION AVANT D’OUVRIR
4
Secure the
cable with the
clamp. The
clamp must
lean against
the cable’s
outer sheath.
Insert each wire in
its terminal and
firmly tighten the
wire connectors. A
loose connection
can be a fire
hazard.
3
RM3250ZB
Cut and unsheathe the
wires according to the size
indicated in the installation
template.
Fix the controller to the wall.
RM3250ZB
zigbee 3.0
Auto
DR

ON
Power
RM3250ZB
CAUTION
DISCONNECT POWER BEFORE OPENING
AVERTISSEMENT
COUPER L’ALIMENTATION AVANT D’OUVRIR
1
2
3
660-2507-0004-A
For more information, visit our Website:
When your controller is
connected, close the
connectivity session
of your Control4
hub.
Initiate the Control4
controller connectivity
session by referring to
it's user guide.
For more information, visit our Website:
www.sinopetech.com
Link your controller to a Control4 home automation system This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPÉ TECHNOLOGIES INC. warrants the components of their
products against defects in material and workmanship for a 3 year
period from the date of purchase, under normal use and service,
when proof of purchase of such is provided to the manufacturer.
This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been
improperly installed, misused or accidentally damaged. The
obligation of Sinopé Technologies Inc., under the terms of this
warranty, will be to supply a new unit and this releases the
manufacturer from paying the installation costs or other secondary
charges linked to replacing the unit or the components.
Connect your load
controller to the
network by pressing
the " " button
4 times.
Applications
This unit can control different types of devices such as:
Electric water heater
Pool pump and filter
Window AC unit
Outdoor lighting
Irrigation pump
Maximum load:
The indicator
Flashes: Device is connecting.
Lit: Device is connected.
OFF: Connection has failed.*
To be informed about our upcoming products:
or subscribe to our newsletter.
Good to know!
Every year, heating your home represents more than 50% of your
electrical bill. Your water heater arrives in second with nearly
20%. About 15% of the energy consumed only serves to maintain
the temperature in the tank, even when the water isn’t in use.
Turning off your electric water heater during an extended
absence is a good way to save money.
Note: If your water heater has been turned off for several days, it
is recommended to wait until the water temperature has
reached 60 °C (140 °F) and to let the hot water run for a few
minutes when the heater is switched back on.
Transmitter Module IC: 22394-ZBM1501 /
FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
*Refer to the “support” section of our
Website to troubleshoot the unit.
Operating voltage: 120 - 347 Vac, 50 / 60 Hz
Consumption:
Load activated: 0.5 W @ 120 - 240 Vac
Load standby: 0.47 W @ 120 - 240 Vac
Operating temperature: -20 °C to 40 °C (-4 °F to 104 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Zigbee 3.0 profile
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
Indoor installation only.
Conforms to ANSI/UL Std. 916
Certified under CAN/CSA Std. C22.2 No205-12
Parameters
All the parameters of your electrical load controller can be
programmed through the interface of your Control4 home
automation system. From this interface, you will be able to
control your load remotely, change programming periods,
consult consumption history and much more.
Disconnect your controller from a Control4 home
automation system
To disconnect your load controller
from a Control4 controller, press the
" " and main buttons
simultaneously for 10 seconds.
This action will also restore the
factory settings of your controller.
All your settings will be deleted.
ON
Power
RM3250ZB
CAUTION
DISCONNECT POWER BEFORE OPENING
AVERTISSEMENT
COUPER L’ALIMENTATION AVANT D’OUVRIR
20 A
15 A
50 A
20 A
20 A
15 A
3 HP
50 A
20 A
20 A
15 A
3 HP
50 A
20 A
20 A
15 A
1.5 HP
Resistive load
Incandescent lamp
Magnetic ballast
Electronic ballast
Motor
120 V 240 V 277 V 347 V
Technical specifications
Auto
DR
Auto
DR