Sinope DM2550ZB User manual

SINGLE POLE WIRING DIAGRAM
3-WAY WIRING DIAGRAM
Warnings
CAUTION!
This dimmer requires a neutral wire. If your electrical box
does not have a neutral wire, you can either add one or
install the dimmer at a different location.
The installation of this dimmer must be performed by a
certified electrician and comply with the national and local
electrical codes and regulations.
To reduce the risk of overheating and possible damage to
another device, do not install to control an outlet, a motor
or a transformer.
DM2550ZB
Installation Guide
Smart Adaptive
Phase Dimmer
zigbee 3.0
YOUR SMART DIMMER DM2550ZB
INSTALL YOUR DIMMER
Press once to turn ON
the light. Hold down
the button to increase
the intensity. Press twice
to turn on the light
at maximum intensity.
Press once to turn
OFF the light. Hold down
the button to decrease
the intensity.
Indicator light
Light turned ON = Blue
Light turned OFF = Amber
The indicator intensity can be changed from Neviweb
and some compatible Zigbee gateways.
Make sure that the breaker for your switch
is OFF at the main electrical panel then
remove the old switch.
Use the provided screws to secure the
dimmer to the electrical box.
Then, place the wall plate.
12Use the provided connectors to
connect the wires as follows:
*Note: For a single pole installation, do
not remove the label on the blue wire.
For a 3-way installation, see the 3-way
wiring diagram section above.
3Power up
the dimmer.
4
Red
Black
White
Blue
Load
Line
Neutral
None*
Make sure to firmly tighten the
wire connectors for a secure
connection. A loose
connection can be a fire
hazard. Special CO/ALR
solderless connectors must be
used when connecting with
aluminum conductors.
Black (line)
Blue (3-way)
White (neutral)
Red (load)
Electrical
Panel
Load
DM2550ZB
Load
Line
Single Pole
switch
Electrical
Panel
DM2550ZB
Red (load)
Black (line)
Blue (3-way)
White (neutral)
Load
red
black
white
blue
load
line
Neutral
white( )
Neutral
(white)
line
load

DISCONNECT YOUR DIMMER FROM
THE GT130 GATEWAY OR A
COMPATIBLE ZIGBEE SYSTEM
CONNECT YOUR DIMMER TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
660-2132-0001-B
TECHNICAL SPECIFICATIONS:
MAXIMUM LOAD PER DIMMER FOR A SINGLE
OR A MULTI-GANG INSTALLATION:
Single installation
Multi-gang (2 units)
Multi-gang (3 units)
Protocol: Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
To disconnect your dimmer from the GT130
gateway or a compatible Zigbee system, press
the 2 buttons of the dimmer simultaneously for
10 seconds.
1
Connect all your dimmers the
same way, by going to the next
closest dimmer.
3When all your devices are
connected, close the
connectivity session of
your GT130 gateway or
your compatible Zigbee
gateway.
4
Connect your dimmer to the gateway by pressing
simultaneously the two dimmer buttons for 1 second.
The indicator flashes blue = Connecting
The indicator turns green = Connected
If the connectivity fails, the indicator will
turn red. Refer to our Website to
troubleshoot the unit.
After a few seconds, the indicator
changes color depending on the dimmer status.
(Turned ON = blue, Turned OFF = amber)
2
Hub
2nd
1st
3rd
Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play
and the Google Play logo are trademarks of Google Inc.
Incandescent
Lamp
600 W
500 W
400 W
600 W
500 W
400 W
150 W
150 W
150 W
Halogen
Lamp
Dimmable
LED / CFL
ADD YOUR DIMMER TO THE GT130 GATEWAY
AND NEVIWEB
Tap the then select "Add Device"
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to open an account and add
your device.
Follow the steps of the Installation Wizard
3
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
For more information, visit our Website:
Transmitter Module IC: 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Operating voltage: 120 Vac, 60 Hz
Operation temp.: 0 °C to 40 °C (32 °F to 104 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Standard UL: Conforms to ANSI/UL Std. 1472
Standard CSA: Certified to CAN/CSA Std. C22.2#184.1
PROVIDED CONNECTORS SPECIFICATIONS:
Stripping length: 16 mm
Wires: 22-10 AWG, Cu
Combinations: Max. 2 #12 & 2 #14, Min. 3 #20 Sol.
16 mm
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide
for the latter.
TROUBLESHOOTING
LED bulbs flicker at low intensity
The minimum dimming light intensity can be adjusted in the
Neviweb app to prevent the LED bulbs from flickering.
See the following link for more information:
https://support.sinopetech.com/en/1.2.3.2.1/
Bulbs flicker at low and high intensity
The DM2550ZB dimmer is configured in reverse phase by
default to ensure more compatibility with most LED,
incandescent, CFL, and halogen bulbs. If a flickering problem
persists, it is possible to change the control mode in the
dimmer settings on the Neviweb app.