SIRUI P-424FS User manual

P-424FS & P-424FL Video/Photo Monopod
V1.0 2022.09.26

1/16 2/16
1. Parts Name 2. Retractable Legs
3. 360° Panning System
360° Panning
Section
The wrist strap can be easily taken off.
a.Unlock
b.Extend or retract
c.Lock
Twist the Upper Twist Collar to lock/unlock the
main tube section.
Clockwise Turn: Secure
Counter-clockwise Turn: Unlock
3/8" and 1/4" Mounting Screw
Mounting Platform
Top Quick Release Sleeve
Flip Locks
Upper Twist Collar
Wrist Strap
Bottom Quick Release Sleeve
Tripod Base
Release Button
Rubber
Foot
Ball Locking Knob

3/16 4/16
4. Friction Adjustments and All-Round 36° Tilting
4.1 Use the Ball Locking Knob to lock the ball or adjust the friction.
4.2 Loosen the Ball Locking Knob to tilt the monopod 36° in any
direction.
Clockwise Turn: Secure
Counter-clockwise Turn: Unlock
Pull out the knob to change
its position.
5. Tripod Base Setup
5.1 Open the base.
5.2 Fold up the base
Open up the base
in the direction
of the arrow
Press the Release
Button Fold up the base in the
direction of the arrow
Attach a head or other
photography equipment
to the Mounting Platform.
36° 36°

5/16 6/16
6. Inverting the 3/8" and 1/4" Mounting Screw
7. Monopod
8. Low Profile Tripod
Suggestion 1: Pair the monopod with the VH-90 platform
or VA-5/VH-10 fluid head from SIRUI.
a.Press the button
b.Take out the screw c.Invert the screw and insert
it into the platform.
Press and hold the button
Fig. A
d.Release the button when
the screw hits the end.
Inverting the screw:
1. Press the button on the side of the platform to take out the screw.
2. Invert the screw and insert it into the platform. Don't release the button until
the screw hits the end.
Pull down the Bottom
Quick Release Sleeve
Take out the leg tube
section
Attach the Rubber
Foot to the bottom
Pull down the Bottom
Quick Release Sleeve
Insert the Mounting
Platform
Take out the Mounting Platform
Pull down the Top Quick Release Sleeve
The base can be
adjusted in height
to adapt to various
settings.
Vertical notch is designed
for portrait shooting
VH-90 Platform VA-5/VH-10 Fluid Head

7/16 8/16
Suggestion 2: Instructions on using the low profile tripod
Caution!
To protect your photo/video equipment, please
hold the equipment with your hands or step on
the tripod base while shooting.
Notice:
1. Please make sure the buckles are locked securely and hold the monopod with your
hands when adjusting the Upper Twist Collar and the Ball Locking Knob.
2. Place the monopod on a flat surface to detach it.
3. Please use the tripod base (rubber feet attached) on a flat surface.
4. Hold the camera with your hands before pulling down the Top/Bottom Quick Release Sleeve.
Do not move the extended monopod with
a camera mounted around. Extend the leg
tubes from large to small and retract the
leg tubes from small to large.
CAUTION!
P-424FS/FL Video/Photo Monopod Specs
P-424FS 4 36/1.42 25/0.98 1600/63.00 650/25.60 1490/58.66 540/21.26
P-424FL 4 36/1.42 25/0.98 1900/74.80 730/28.74 1790/70.74 610/24.01
1.2/2.65
1.25/2.75
12/26.45
12/26.45
(without base)
(without base)
Attach a head or other photography
equipmentto the tripod
Adjust the friction
When tilting is required
When tilting is not required
Tighten the Ball
Locking Knob