SISO Dave User manual

1
Electronic Combinaon Cam Lock ”Dave”
SISO A/S
Mileparken 11
DK-2740 Skovlunde
Denmark
Phone [phone]
Fax [phone]
www.siso.dk
[email protected]
VAT: DK 24786013
1. Baery Installaon
1.1 Insert baery
2. Operang Instrucon
2.1 Unlocking
2.1.1 For private version
2.1.2 For public version
2.2 Locking
2.2.1 For private version
2.2.2 For public version
2.3 Change code (only for private version)
2.4 If password forgoen
3. Other Instrucon
3.1 Acousc & opc nocaons
3.2 Technical Parameters
4. Installaon guide

2
Electronic Combinaon Cam Lock ”Dave”
SISO A/S
Mileparken 11
DK-2740 Skovlunde
Denmark
Phone [phone]
Fax [phone]
www.siso.dk
[email protected]
VAT: DK 24786013
1. Baery Installaon
1.1 Insert baery
Baery type CR1220 (not included), remove the baery cover by
inserng the needle (included with the accesoires) in the lock hole
(A) and pulling out the baery cover carefully (B).
Place the baery (C) in the holder and push back the cover in place.
2. Operang Instrucon
2.1 Unlocking
2.1.1 For private version (the Factory default code is “3”)
Enter “User code + OK” and hear a long sound “Ti~”, then rotate the knob to unlock within 3 seconds.
2.1.2 For public version (the Factory default code is “123”)
Enter “User code + OK” and hear a long sound “Ti~”, then rotate the knob to unlock within 3 seconds.
(Remark: the code will automacally be deleted aer use, so the next user can use their own new code.)
2.2 Locking
2.2.1 For private version
Rotate the knob anclockwise to the exact posion to lock.
2.2.2 For public version
Enter“user code + OK” rst. (the user code can be set by any combinaon of 1,2,3, and ranging
from 3 to 6 digits). The rotate the knob anclockwise to lock.
2.3 Change code (only for private version)
Input “Old code + OK + OK + new code + OK”, then you can hear a long sound “Ti~”, which
means the new code is set successfully. For example: change the default code from 3 to 123 >> input “3 +
OK + OK + 123 + OK”, then you can hear a long sound “Ti:~”, that means the new code comes into eect.
2.4 Forgoen password
Needle
A
B
C
For Private version:
Enter Resetcode* "xxxx” then press OK buon, the lock is reset to factory status.
Use now the factory default user code 3 + OK buon and then turn the knob - You can now set your personal code.
For Public version:
Enter Resetcode* "xxxx” then press OK buon, the lock is reset to factory status.
Use now the factory default user code 123 + OK buon and then turn the knob - You can now set your personal code.
*For Resetcode: please note your Mastercode (on right side of the lock) and contact your furniture supplier.

3
Electronic Combinaon Cam Lock ”Dave”
SISO A/S
Mileparken 11
DK-2740 Skovlunde
Denmark
Phone [phone]
Fax [phone]
www.siso.dk
[email protected]
VAT: DK 24786013
3. Other instrucons
3.1 Acousc & opc nocaons
Note 1: Replacing baery when it is in low power - during the low power condion, user can sll unlock for 500
mes.
Note 2: Three mes input the code incorrectly will cause alarm sounds for 60 seconds. Once the correct code has
been put in, the alarm will stop.
3.2 Technical parameters
Working voltage DC 2.3-3.3V
Baery SPEC CR 1220
Standby current ≤ 2uA
Max. current ≤ 5mA and me of duraon ≤ 35ms
Baery life 1-2 years unlock 30-50 mes one day
Operaon temp -5 degrees to +50 degrees Celsius
Relave humidity 20% to 80%
Material Zinc Alloy/ABS
Diameter of mounng Apply to diameter 16mm
Panel Thickness Steel: 0,5-12mm Wood: 0,5-22mm
Cercaon CE/FCC/PSE/ROHS/SGS/SST
No Name Sound nocaon Explanaon
1Buon Ti-- short sound The "keypress" is eecve
2Unlocking change Ti----long sound Operaon correct. Unlocking/change code successfully
3Error Ti Ti two sounds Operaon, error, input failure
4Low power Ti Ti Ti three sounds Low power, replace a new baery
5Alarm Ti… alarm sounds 3 mes wrong input will cause alarm sound for 60 seconds

4
Electronic Combinaon Cam Lock ”Dave”
SISO A/S
Mileparken 11
DK-2740 Skovlunde
Denmark
Phone [phone]
Fax [phone]
www.siso.dk
[email protected]
VAT: DK 24786013
4. Installaon guide
1 : 1 Hole drawing Assembling drawing Accessories
List of accessories