SITGroup 584 PROFLAME G Technical manual

9.957.001 00
PROFLAME G FIRE SYSTEM
USE AND INSTALLATION INSTRUCTIONS
Read the instructions before use. This control must be installed in accordance with the rules in force.

English -
8
2
2
ENGLISH
The 584 Proflame G Fire is a modular remote control system that directs the many
functions of today’s hearth appliances. It is configured to control the on/off
operation of the main burner. The Proflame G Fire is specifically developed to be
used with multifunctional gas controls.

3
Remote Control
Supply voltage 4.5 V (three 1.5 V AAA batteries)
Ambient temperature ratings 0 - 60 °C (32 - 140 °F)
Radio frequency 315 MHz
Receiver
Supply voltage 6.0 V (four 1.5 V AA batteries)
Ambient temperature ratings 0 - 60 °C (32 - 140 °F)
Radio frequency 315 MHz
TECHNICAL DATA
ENGLISH
WARNING
THE TRANSMITTER AND THE RECEIVER ARE RADIO FREQUENCY APPLIANCES. IF
THE RECEIVER IS MOUNTED INSIDE METALLIC CASES, SEVERE LOSS OF
PERFORMANCES ( REDUCTION OF THE RANGE OF WORKING) MAY RESULT.
ATTENTION!
- TURN “OFF” MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION OR
MAINTENANCE OF THE RECEIVER.
- PLACE THE RECEIVER’S 3 POSITION SLIDER SWITCH IN THE “OFF” POSITION
DURING INSTALLATION OR MAINTENANCE.
- TURN “OFF” MAIN GAS SUPPLY OF THE APPLIANCE PRIOR TO REMOVING OR
REINSERTING THE BATTERIES IN THE RECEIVER.

4
ENGLISH
The 584 PROFLAME G Fire System consists of two elements:
1. 584 PROFLAME G Fire Transmitter.
2. The 584 PROFLAME G Fire Receiver.
The 584 PROFLAME G Fire System complements any millivolt Combination Gas Control.
The Proflame Transmitter uses the latest digital technology, see Fig. 1.
With the 584 PROFLAME G Fire Transmitter it is possible to turn the appliance on and off.
The 584 PROFLAME G Fire Transmitter is the Remote Control that commands the Receiver. All the
commands are given with one button: see Fig. 1.
Moving the side slider in the direction of the transmission light it is also possible to disconnect the
electric supply of the internal batteries (child safety feature).
REMOTE CONTROL
SYSTEM DESCRIPTION
The 584 PROFLAME G Receiver may be installed in a standard single gang wall switch box or in a
low temperature area of the hearth appliance. The receiver accepts commands from the transmitter
to operate the functions included with a particular Proflame system configuration.
The receiver can be set to one of three positions: On (manual override), Command (remote control)
or Off using the three position slider.
When the switch is in the MANUAL position, an electrical circuit is created bypassing the transmitter-
controlled contacts, and the appliance burner is turned ON. When the switch is in the REMOTE
position the appliance is being controlled by the remote control system. When the switch is in the
OFF position the appliance burner is turned OFF.
RECEIVER
ON /OFF Key
Transmission light
Fig. 1: 584 PROFLAME G Fire Transmitter
Side slider

Fig. 3: 584 PROFLAME G Fire Receiver batteries housing
5
ENGLISH
Fig. 2: 584 PROFLAME G Fire Receiver
2 PIN terminal
3 Positions Slider
Installing the wall cover plate
1. Install the receiver in the J box using the existing J box screws.
2. Place the slider into the cover plate with the white dot on the right
side.
3. Put the receiver switch in the “OFF” position.
4. Make sure the receiver and cover plate words “ON” are on the
same side.
5. Align the slider with the switch on the receiver and couple the
switch into the slider.
6. Align the screw holes.
7. Using the two (2) screws provided secure the cover plate to the receiver.

6
ENGLISH
The 584 PROFLAME G Fire System is designed to command any millivolt Combination Gas Control.
The wiring diagram of all the electrical connections is shown in Fig. 4.
Particularly shown are three main elements of the system.
The Receiver and 820 Nova mV Gas Valve can all be connected by single wire harness (not
supplied).
FUNCTIONALITY OF THE RECEIVER
The Receiver is supplied by four (4) AA batteries, see Fig. 3. The receiver accepts commands via
radio signal sent from the transmitter. The receiver sends commands by the wire harness to the
multifunctional gas control. When the system is turned on, an acoustic signal (“beep”) is generated to
indicate that the Receiver is ready to receive commands from the Remote Control.
FUNCTIONALITY OF THE REMOTE CONTROL
When the batteries are installed into the Remote control and the side slider is in the position shown in
Fig. 5, the LED on the transmitter illuminates each time the ON/OFF button is depressed.
INSTALLATION
OPERATING PROCEDURE
TP
TH
TPTH
Green
Whi
te
Red
Black
(+) (-)
Fig. 4: Wiring diagram.

7
ENGLISH
COMMUNICATION BETWEEN THE REMOTE CONTROL AND THE RECEIVER
To program the transmitter to the receiver, move the three positions slider of the receiver in the
REMOTE position ( see Fig. 2 in page 5) and depress the ON/OFF key of the transmitter. The
System has got an automatic learning mode that allows the receiver to mate with a new transmitter
in the event that the transmitter must be replaced. As soon as the receiver receives the first correct
command from any remote control it captures the new address and then "beeps" 3 times to confirm
the synchronization and command execution.
TURN ON THE APPLIANCE
When the ON/OFF key is pressed, the LED on the transmitter illuminates and the Remote Control is
switched on. At the same time the Receiver connects the thermopile to the gas valve millivolt coil
and the appliance main burner turns on in the high position. An single acoustic signal from the
Receiver confirms the reception of the command.
TURN OFF THE APPLIANCE
If the appliance and the Remote Control are switched on, when the ON/OFF key is pressed,the
Remote control is turned off. At the same time the Receiver removes power from the gas valve
millivolt coil and the appliance main burner turns off. An double acoustic signal from the Receiver
confirms the reception of the command.
ON /OFF Key
Transmission light
Fig. 5: 584 PROFLAME G Fire Transmitter
Side slider
The duration of the Remote Control batteries depends on many factors: the quality of the batteries
used, the number of ignitions of the appliance, etc.
When the transmitter batteries are low, depressing the ON/OFF key the light intensity of the LED
(see Fig. 5) is weak to alert of a low battery condition before losing battery power at all. As soon as
the depleted batteries are replaced, the Transmitter will restart its normal operation.
LOW BATTERY DETECTION (Transmitter)
The duration of the Receiver batteries depends on many factors: the quality of the batteries used,
the number of ignitions of the appliance, etc.
LOW BATTERY DETECTION (RECEIVER)

8
ENGLISH
If the batteries of the Receiver are low, the appliance can be switched on manually by moving
the 3 position slider switch on the Receiver to the ON position, see Fig. 3 in Page 5.
BACKUP FUNCTION
With this function it is possible to deactivate the remote control key, see Fig. 6.
CHILD SAFETY LOCK-OUT
If the receiver batteries are low, a triple acoustic signal will be emitted by the receiver when it
receives a command from the transmitter depressing the ON/OFF key. This is an alert of a low
battery condition before losing battery power at all. As soon as the depleted batteries are
replaced, the acoustic signal from the receiver confirms the reception of the ON/OFF command
from the transmitter.
Fig. 6: 584 PROFLAME G Fire Transmitter child safety function
Child safety function OFF Child safety function ON
CAUTION
Property Damage Hazard.
Excessive heat can cause property damage
The fireplace can stay ignited for many hours. Take care to turn off the fireplace if it is
unattended by adult people.
Do not leave the Remote Control where children can reach it.
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes the ignition of the fireplace. The fireplace can turn on suddenly. Keep
away from the burner, especially when operating on the BACKUP switch.
WARNINGS AND CAUTIONS