FBII XL-20 User manual

XL-20
Security System
Owner’s Manual
N9824 11/97

QUICK REFERENCE.................................................................................................................1
Turn System On ...................................................................................................................1
Turn System Off ...................................................................................................................1
Turn System On and Stay Inside..........................................................................................1
Turn System On: Perimeter Sensors
Instant Mode and Stay Inside ...............................................................................................1
Smoke Detector Reset .........................................................................................................1
INTRODUCTION.........................................................................................................................2
SYSTEM REFERENCE ..............................................................................................................3
XK-108 KEYPAD.........................................................................................................................5
TURNING THE SYSTEM ON .....................................................................................................8
Turn the System On and Leave............................................................................................8
Not Ready.............................................................................................................................8
To Turn the System On - Not Ready ....................................................................................9
Turn System On and Stay Inside..........................................................................................9
Turn System On: Perimeter Sensors
Instant Mode and Stay Inside ...............................................................................................9
Turn the System On with All
Sensors in Instant Response Mode......................................................................................9
Bypass..................................................................................................................................10
Turn the System Off .............................................................................................................10
USER CODES ............................................................................................................................12
Add or Chan
g
e a User Code ................................................................................................12
Delete a User Code ..............................................................................................................12
KEYPAD FUNCTIONS................................................................................................................13
Turn System On Only...........................................................................................................13
Keypad Send Help Conditions..............................................................................................13
Quick On...............................................................................................................................13
Quick Forced On ..................................................................................................................13
Quick Exit .............................................................................................................................14
Quick Bypass........................................................................................................................14
Set Time and Date................................................................................................................14
Turn Chime On/Off ...............................................................................................................14
SYSTEM TEST ...........................................................................................................................15
INSTALLATION LAYOUT ...........................................................................................................16
SYSTEM LIMITATIONS..............................................................................................................18
GLOSSARY ................................................................................................................................20
FCC STATEMENT......................................................................................................................22
TELEPHONE OPERATIONAL PROBLEMS...............................................................................22
LIMITED WARRANTY ................................................................................................................25
TABLE OF CONTENTS
XL-20 Owner’s Manual

XL-20 Owner’s Manual - Pa
g
e 1
Quick Reference
TURN SYSTEM ON
Check to make sure the system is READY - Green ready light is lit
Enter your four digit user code (or press the Arm button on your keyfob).
The On/Off (Arm) light will light.
Exit through a door designated by your installer as an exit/entry door.
TURN SYSTEM OFF
Enter through a door designated by your installer as an exit/entry door.
Enter your four digit user code (or press the Disarm button on your keyfob).
The System On (Arm) light will go out.
TURN SYSTEM ON AND STAY INSIDE
Check to make sure the system is READY - Green ready light is lit.
Followed by your user code
The On/Off (arm) light and the Stay light will both light.
REMEMBER: You must turn the system off if you want to open the door or
leave the premises after the exit time has passed.
TURN THE SYSTEM ON: PERIMETER SENSORS INSTANT
MODE AND STAY INSIDE
Check to make sure the system is READY - Green ready light is lit
followed by
followed by your user code
The On/Off light, the Instant light and the Stay light will all be on.
SMOKE DETECTOR RESET
Enter your four digit user code.
STAY
INSTANT
STAY

XL-20 Owner’s Manual - Pa
g
e 2
Introduction
Congratulations on your decision to protect your home or business with the XL-
20 security system. You have chosen a reliable, state of the art security system
that is remarkably easy to operate. Your system has been professionally installed
by your local Security Company who can explain the specifics of your system.
The keypad is the input and display device for your security system. Your
system uses a XK-108 keypad. The XK-108 is a surface mount keypad
containing indicator lights for each of the 8 zones (areas of protection). The door
covering the buttons is optional and can be removed.
The XL-20 is listed by Underwriters Laboratories for Household Fire and
Burglary applications.
Throughout this manual the following conventions are used to display the
keystrokes required to perform the functions.
Button labeled BYPASS
Button labeled INSTANT
Button labeled STAY
Button labeled CODE
Four digit user code
Please keep your manual in a convenient location so you can refer to it if needed.
BYPASS
INSTANT
STAY
CODE

XL-20 Owner’s Manual - Pa
g
e 3
SYSTEM REFERENCE
The following SEND HELP ALERTS are programmed into my system. Both
Buttons must be pressed at the same time to activate the alert. The buttons you
press depend on which type of keypad you have. Your installer will show you
how to activate these emergency keys.
ZONE
1
2
3
4
5
6
7
8
DESCRIPTION
Entry Time
Entry Time
Door
Door
Exit Time
Entry Time is the same for all desi
g
nated Entry/Exit Doors.
ZONE DESCRIPTION BUTTONS
Left
Center
Right
# & *
7 & 9
1 & 3

XL-20 Owner’s Manual - Pa
g
e 4
USER ID
1
2
3
4
5
ASSIGNED TO
Account #
Telephone #
*Master User can add, chan
g
e, or erase other user codes.
(MASTER USER 1)
6
Monitorin
g
Station Information

XL-20 Owner’s Manual - Pa
g
e 5
XK-108 KEYPAD
1) ZONE STATUS LEDS
These LEDS display the current zone status including alarms, bypasses, troubles
and faults. Each condition will cause these LEDS to operate differently as
follows:
ALARMS Fast Blink (approx. 150 ms. ON - 150 ms. OFF).
TROUBLES Slow Pulse (approx. 600 ms. ON - 600 ms. OFF).
BYPASSES Wink (100 ms. ON - 900 ms. OFF). Zone bypasses are displayed as
a very slow wink of the zone LED light.
FAULTED ZONES Solid ON. Faulted zones are the lowest priority indication.
Faulted burglary zones are displayed with the LED solidly ON while the system
is disarmed.
NORMAL OFF
2) ARM/DISARM LED
This LED indicates whether the system is currently armed (ON) or disarmed
(OFF). This LED will also blink fast to show that alarms have occurred or blink
slowly upon failure to communicate with the Central Station.
ARM
AC/LB
READY
1
2
3
4
5
6
7
8
XK-108 KEYPAD
STAY
INST
COVER
OPEN
Stay Instant
Bypass Code
*0#
789
456
123
PAF
2
5
6
1
3
4
7
9
10
8
11
TX LB
RF. SPVR
12
13

XL-20 Owner’s Manual - Pa
g
e 6
3) STAY LED
This LED displays whether the system has been armed in the STAY mode or the
STAY/INSTANT mode. If the INSTANT LED is ON and the STAY LED is ON,
then the system is in the STAY/INSTANT mode. If the INSTANT LED is OFF
and the STAY LED is ON, then the system is in the STAY mode only. STAY/
INSTANT is enabled in programming question 05, location 2. In either mode the
STAY LED indicates the following:
ON Interior zones are bypassed
OFF Interior zones are active armed
4) INSTANT LED
This LED displays whether the system has been armed in the STAY/INSTANT
mode, meaning that the system is currently armed, all delay zones are instant and
all interior zones are bypassed. NOTE: See programming question 05, location 2.
ON Delay zones are currently instant
OFF Delay zones are normal
5) AC/LOW BATTERY LED
This indicator light displays the current power status of the panel as follows;
ON AC is present
OFF No AC, running on battery backup
Slow Blink Low battery condition detected
6) READY LED
This LED displays whether the system is ready for arming. The READY light is
common to all BURGLARY ZONES with the following indications:
ON System ready to be armed
OFF System not ready to be armed
Slow Blink Indicates Installer programming mode
Fast Blink Alarm Memory Mode
7) STAY BUTTON
The STAY button enables arming the system, excluding zones programmed as
interior zones. This will provide exterior protection of the location while

XL-20 Owner’s Manual - Pa
g
e 7
allowing full access throughout the interior.
8) BYPASS BUTTON
The BYPASS button is used to temporarily exclude protection of a specific zone.
9) INSTANT BUTTON
The INSTANT button enables arming the system eliminating entry/exit delays. If
enabled with the STAY button, it enables arming the system in the STAY/
INSTANT mode. NOTE: The INSTANT modes are enabled in question #05,
location 2.
10) CODE BUTTON
The CODE button is used to enter the installer programming mode and entry of
user codes.
11) KEYPAD AUXILIARY KEYS
Pressing the two keys (top & bottom) labeled "P" at the same time initiates a CS
transmission, if programmed, of PANIC, AUXILIARY or FIRE, annunciates the
keypad sounder and turns on the bell output. If not programmed to transmit, these
keys can only result in a local warning as follows (see question 05, location 1):
Keypad Sounder - Steady for PANIC, Pulsing for FIRE and AUXILIARY
Bell Output - Steady for PANIC, Pulsing for FIRE
12) TX LB LED
This LED will pulse whenever any RF transmitter has a low battery. Also, the
corresponding zone LED for that transmitter will pulse.
13) RF SPVR LED
This LED will indicate three different RF supervisory conditions and one bell
output supervisory condition as follows:
No supervision conditions exist (normal)
ON RF transmitter has not checked in for more than 12 hours
BLINKING (fast) RF transmitter reports a tamper condition
BLINKING (slow) Bell Output is in supervision

XL-20 Owner’s Manual - Pa
g
e 8
TURNING THE SYSTEM ON
You can turn the Burglar portion of your security system on and off. Before you
turn the system on it must be ready. If you have a protected door open, or
someone is moving by a motion detector the system will not show ready.
The system is ready if the ready light is on.
TURN THE SYSTEM ON AND LEAVE
Enter your four digit user code.
The System On (Arm) light will go on.
Exit through a door designated by your installer as an exit/entry door. You must
leave within the period of time known as the exit time. Check the reference sheet
for the time that has been set for your system.
NOT READY
If the system is not ready to be armed, the READY light will be off and the Zone
lights will show which zone or zones are not ready. The zone lights on the
keypad indicate the following conditions:
Fast Blink Alarm
Slow Blink/Low Intensity Bypass
Slow Pulse Trouble
Solid On Not Ready
Example: If the Ready light is not lit and the zone one light is solid on. An alarm
sensor on zone one is not normal. This might mean that a window is open or
someone is walking through a motion sensor. Check all sensors on zone one and
resolve the problem. When all sensors are normal the Ready light will come on
and the zone light will go out.
TO TURN THE SYSTEM ON - NOT READY
Determine which zone or zones is not ready, resolve the problem and turn the
system on normally. If the problem cannot be resolved you may bypass the zone
that is not ready. Bypassing should only be done if the problem on the zone
cannot be resolved OR if you intentionally wish to leave the zone off. Example:
you wish to keep the window open for ventilation. Zones that are bypassed are
not protected when the system is on. See Bypass for the correct procedure.