SKC 231 series User manual

Dual Stainless Steel Fitted Bags
231 and 237 Series Sample Bags
Operating Instructions
863 Valley View Road, Eighty Four, PA 15330 USA
Tel: [phone] Fax: [phone] e-mail: [email protected]
The 231 and 237 Series sample bags feature dual stainless steel fiings – an inlet
valve for flushing and filling and a PTFE-lined septum fiing for removing samples.
Guidelines for Bag Sampling
1. Ensure that the bag material and fiings are appropriate for the compounds
to be sampled.
2. Use only PTFE tubing to connect the sample bag to the pump to prevent sample
loss by adsorption on tubing walls.
3. Before using, flush the bag thoroughly with purified air or nitrogen.
4. Analyze the sample within 24 to 48 hours. Long-term storage of air-contaminant
mixtures in bags is not recommended.
5. Do not ship sample bags by air unless the cargo cabin is pressurized.
Cautions
Maximum Operating Temperature
Do not exceed these specifications.
• 231 Series Bags: 225 F (107 C) due to fiing O-ring temperature rating
• 237 Series Bags: 140 F (60 C) due to the SamplePro®FlexFilm bag material
temperature rating
Do not use sample bags to sample compounds with boiling points > 249.8 F (121 C).
SKC sample bags are designed for sampling air at atmospheric pressure only.
Aempting to pressurize the bag can result in bag rupture and sample loss. Do not
ship bag samples by air freight in a non-pressurized cargo cabin. Bags can burst
under such conditions.
All federal and state packaging and transporting regulations apply.
Failure to follow warnings and cautions voids any warranty.
Sample bags are designed for single use only.

®
000277
Operation
1. Flush the bag at least 3 times with purified air or nitrogen before use.
2. To fill the bag, connect PTFE tubing from the exhaust port of an air sample
pump to the hose connection on the bag (stem protruding from the top of
the inlet fiing).
3. Ensure that the valve is locked open by tightening the
knurled thumbscrew clockwise until snug. Turn on the
sample pump to fill the bag (see Proper Bag Inflation).
Do not sample compounds that exceed the 225 F (107.2 C)
temperature rating of the fiing O-rings.
When using 237 Series SamplePro FlexFilm bags, do not
sample compounds that exceed 140 F (60 C) temperature.
Do not use sample bags to sample compounds with
boiling points > 249.8 F (121 C).
4. When sampling is complete, turn offthe pump and
loosen the knurled thumbscrew a maximum of
2 revolutions.
5. Close the shut-offvalve by pulling up on the valve stem.
(Note: Ensure the PTFE tubing is not pulled offwhile
pulling up on the valve stem.) Tighten the knurled screw
until snug to lock the valve closed.
6. To withdraw samples using a needle and syringe,
carefully insert the needle into the port in the septum
fiing and pierce the septum.
Do not allow the syringe needle to puncture the bag
material when piercing the septum.
2

Proper Bag Inflation
Avoid filling any bag more than 80% of its maximum volume. At the end of the
sampling period, turn the pump offand close the valve on the bag. Tighten the
knurled screw to lock the valve closed.
Incorrect
Inflation
Correct
Inflation
3
SKC sample bags are available in Tedlar
®
, FluoroFilm FEP, SamplePro FlexFilm, FlexFoil
®
PLUS, and Standard FlexFoil with fittings made of stainless steel, polypropylene, or PTFE
in sizes ranging from 10 milliliters to 100 liters. SKC also manufactures custom sample
bags. Contact SKC at 724-941-9701 or [email protected].

Form 3714 Rev 1402
Accessories
Replacement Septa, pk/10.......................................................................Cat. No. 231-9-04
PTFE Tubing, fits over bag fitting and Grab Air Sample Pump
fittings, 3/16-inch ID, 1/4-inch OD..............................................10 feet.....Cat. No. 231-9-23
PTFE Tubing, fits inside bag fitting,
1/16-inch ID, 1/8-inch OD..........................................................10 feet.....Cat. No. 231-9-21
PTFE Tubing, fits Vac-U-Chamber inlet and 222 Pump fittings,
1/4-inch ID, 5/16-inch OD..........................................................10 feet.....Cat. No. 231-937
50 feet.....Cat. No. 231-924
Twin Port Pocket Pump Tubing Adapter Kit includes two
lengths of silicone tubing: 1/8-inch ID, 1/4-inch OD for bag
fitting and 3/16-inch ID, 3/8-inch OD for pump fitting; use with
Cat. No. 231-9-23 PTFE tubing (above)....................................................Cat. No. 231-926
For more product information or assistance with applications,
contact the SKC Technical Service Department at [email protected].
www.skcinc.com
SKC Limited Warranty and Return Policy
SKC products are subject to the SKC Limited Warranty and Return Policy, which
provides SKC’s sole liability and the buyer’s exclusive remedy. To view the com-
plete SKC Limited Warranty and Return Policy, go to hp://www.skcinc.com/
warranty.asp.