Skope HB85 User manual

Page 1 of 3 PRN80403 Rev. 1.0 Sep. 2023
HB85
User Guide
Thank you for purchasing a SKOPE refrigeration product.
Safety
Always observe safety precautions when using any electrical appliance. Read these instructions carefully and retain
them for future reference.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
•Do not use this appliance for other than its intended use.
•Do not insert fingers/foreign objects into any holes.
•Only use this appliance with the voltage specified on the cabinet rating label.
•Ensure the appliance has adequate ventilation as this is essential to economical, high performance.
•Be careful not to touch moving parts and hot surfaces.
•For your own safety and that of others, ensure that all electrical work is done by authorised personnel.
•If the power supply flexible cord becomes damaged, it must be replaced by an authorised service agent or
similarly qualified person in order to avoid a hazard.
•If installing or removing the refrigeration unit, refer to the Installation Guidelines below, and observe all necessary
safety precautions.
•The appliance is not designed to be stable while in motion. Use extreme caution when moving or transporting it.
•Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
•If the cabinet is to be scrapped, ensure the cabinet is unplugged from the power supply and cut off the mains flex
close to the back of the cabinet. Be mindful of the risk of animals or children becoming trapped in the appliance –
either remove or secure doors if necessary.
•Refrigerant must be removed by a qualified service person and the cabinet recycled/disposed of in accordance
with local regulations.
Service and Support
We know you will get years of satisfaction from your new SKOPE product when you follow a few simple
preventative maintenance guidelines.
Helpful information is available on the SKOPE website: www.skope.com/serviceandsupport
WARNING
•Ensure the appliance is disconnected from the power supply before performing any cleaning or maintenance.
•Do not cover the grilles or block the entry or exhaust of airflow by placing objects up against the refrigeration
unit.
•Should manual defrosting be necessary, turn off the refrigeration system and allow the ice to melt by air
circulation. Collect ice and water during defrost to prevent a slip hazard. Do not use mechanical methods to
remove ice, as this may damage the refrigeration circuit.
•Do not use any electrical devices or appliances inside the food storage compartment.
This cabinet is designed to operate within a specific climatic class
environment. The cabinet rating label inside the cabinet lists the
climate class number.
The cabinet includes relevant hazard symbols that may be
associated with the chiller. Refer to the information below for
symbol description.
Climate class Ambient temperature Relative humidity WARNING
The refrigeration system contains flammable R600a
refrigerant. Do not tamper with it.
The refrigeration system must only be serviced by
qualified personnel.
3 25°C 60%
4 30°C 55%
5 40°C 40%
7 (tropical) 35°C 75%

Page 2 of 3
HB85
PRN80403 Rev. 1.0 Sep. 2023
Installation Guidelines
When installing this cabinet, make sure you consider and meet the installation guidelines below.
Operation
Let the cabinet stand for:
•at least 30 minutes before connecting to the power supply for the first time.
•10 minutes if it has been disconnected from the power supply for any reason.
Ventilation Requirements
You must ensure the cabinet has the following
ventilation clearances at all times:
Shelves
The cabinet is supplied with 2 shelves.
Remove the packaging, then position the shelves at the
required height. The shelves have hooks on the back
which lock them in position.
Ventilation
Ensure all ventilation
requirements below
are met.
Sunlight
Do not install the
cabinet in direct
sunlight.
Uneven Surface
Do not install the
cabinet on an uneven
surface.
Surface
Make sure the
installation surface is
capable of supporting
the loaded cabinet.
Power Supply
Do not overload the
power supply.
Blocking Ventilation
Do not store boxes or
items in front or on
top of the cabinet.
Door Opening
Allow adequate space
for the door to open
and close properly.
Climate Class
Only install the fridge in an
environment within its climate class.
The climate class is stated on the
cabinet rating label.
Stabiliser Feet
To provide adequate stability,
you must screw down the
stabiliser feet (located under
the door) anti-clockwise until
they are firmly in contact
with the floor.
Minimum 100 mm above
Minimum
100 mm
behind
Minimum
100 mm
right side
Minimum
100 mm
left side
Shelf
hook

Page 3 of 3 PRN80403 Rev. 1.0 Sep. 2023
HB85
Loading Product
Let the cabinet run for 30 minutes before loading it with product for the first time. When loading the shelves with
product:
Refrigeration System
The evaporator fan (located inside the cabinet) should operate continuously from the time the cabinet is plugged in.
You can verify this by checking that the air is moving inside the cabinet.
While the fridge is operating it is normal to hear gurgling sounds caused by the flow of refrigerant when each cooling
cycle ends.
The thermostat will click when the refrigeration system switches on and off.
Temperature
The temperature of the fridge is regulated by a thermostat located on the inside back wall of the
cabinet. The temperature is set at the factory and should not require adjusting. The normal
temperature controller setting is 2.
If required, turn the knob:
•clockwise to lower the temperature. Be careful not to set it too low, or product could freeze.
•anti-clockwise to raise the temperature.
•to 0 to switch the refrigeration system off. The fan and lights will stay on.
Lights
You can turn the light on and off using the switch on the right hand side of the LED strip on the ceiling of the cabinet.
Cleaning
Always unplug the cabinet from the mains power supply before cleaning.
Cabinet
•Wipe the inside and outside of the cabinet with a damp cloth and a small amount of detergent, taking care to keep
moisture away from electrical parts.
•Do not use abrasive or corrosive cleaners or boiling water.
•Do not flush the cabinet with water.
•Check that the condensation drain hole at the base of the lower inside rear wall panel on
the left hand side is not blocked.
•Clean the door gasket every three months.
Shelf Loading
Do not overload the
shelves.
Shelf Flexing
Remove product if the
shelf is flexing.
Shelf Overhang
Do not let product
overhang the shelves.
Front
Top
Back
MAX
30kg
per shelf
Internal Airflow
Leave 25 mm space between product
and the back of cabinet interior, and
do not block the drain hole.
6
5
4
3
2
10
7
Light switch
Mechanical
thermostat