Skope ProSpec Series User manual

ProSpec Series
User Guide
Thank you for purchasing a SKOPE refrigeration product.
Safety
Always observe safety precautions when using any electrical appliance. Read these instructions carefully and retain them
for future reference.
• Do not use this appliance for other than its intended use.
• Do not probe any opening.
• Only use this appliance with the voltage specified on the cabinet rating label.
• Ensure the appliance has adequate ventilation as this is essential to economical, high performance.
• Be careful not to touch moving parts and hot surfaces.
• For your own safety and that of others, ensure that all electrical work is done by authorised personnel.
• If the power supply flexible cord becomes damaged, it must be replaced by an authorised service agent or similarly qualified
person in order to avoid a hazard.
• Ensure all necessary safety precautions are observed during installation or removal of the refrigeration unit.
• The appliance is not designed to be stable while in motion. Use extreme caution when moving or transporting it.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Do not exceed a maximum load of 20kg per shelf.
• Please contact SKOPE for advice regarding disposal of this appliance.
WARNING
• Ensure the appliance is disconnected from the power supply before performing any cleaning or maintenance.
• Do not cover the grilles or block the entry or exhaust of airflow by placing objects up against the refrigeration unit.
• Should manual defrosting be necessary, turn off the refrigeration system and allow the ice to melt by air
circulation. Do not use mechanical methods to remove ice, as this may damage the refrigeration circuit.
• Do not use any electrical devices or appliances inside the food storage compartment.
This cabinet is designed to operate within a specific climatic class environment.
See the cabinet rating label inside the cabinet for climate class number.
The cabinet includes relevant hazard symbols that may be associated with the
cooler. Refer to the information below for symbol description.
Climate class Ambient temperature Relative humidity WARNING
The refrigeration system contains flammable R290 refrigerant.
Do not tamper with it.
The refrigeration system must only be serviced by qualified
personnel.
325°C 60%
430°C 55%
540°C 40%
7 (tropical) 35°C 75%

ProSpec Series
Installation Guidelines
Ensure the installation guidelines below are considered and met .
Ventilation Requirements
This cabinet must have the following ventilation clearances at all times:
* When installed for continuous duty in climate class 7 environment (35°C ambient / 75% relative humidity), it is recommended to
provide 50mm clearance around the sides and back of the cabinet.
Ventilation
Ensure all ventilation
requirements below are
met.
Door Opening
Allow adequate space for
the door/s to open and
close properly.
Sunlight
Do not install the cabinet
in direct sunlight.
Uneven Surface
Do not install the cabinet
on an uneven surface.
Surface
The installation surface
must be capable of
supporting the loaded
cabinet.
Power Supply
Do not overload the power
supply.
Blocking Ventilation
Do not store boxes or items in
front or on top of the cabinet.
Climate Class
The cabinet must be
installed in an environment
within its climate class.
The climate class is stated
on the cabinet rating label
inside the fridge, and
explained on the front page
of this user guide.
No below clearance required
Min. 300mm above
No side
clearance
required
No behind
clearance
required
No side
clearance
required
No behind
clearance
required
No below clearance required
No above clearance required
Upright Cabinets Underbench Cabinets
Keep area in front
of grille and doors clear
Keep area in front
of doors clear
**
**

ProSpec Series
Cleaning Before First Use
The cabinet interior and food contact surfaces such as the worktop must be thoroughly cleaned and sanitised before first
use. Ensure the cabinet is unplugged from the power supply before cleaning, and use only standard stainless steel cleaners
suitable for food preparation areas. If required, the cabinet exterior can be cleaned as instructed on the back page of this
user guide.
Shelves
Each shelf is held in place with shelf rails, which clip into the shelf support strips. The shelf rails may be positioned at
different heights to suit various product.
The shelf rails are suitable for use with gastronorm pans.
Loading product
Let the cabinet cool down to the desired storage temperature before loading it with product. When loading the shelves:
Door Lock/s
The cabinet is fitted with key locks, which can be operated with the supplied key.
Electronic Controller
The electronic controller regulates the cabinet internal temperature, signals alarms and captures
operational information. The internal temperature is factory set for storage of perishable product.
To customise the settings to your requirements and view historical data, download the
SKOPE-connect app from the Google Play Store or Apple App Store, and connect via
Bluetooth
®
wireless
technology.
Lights
The interior lights switch on and off automatically depending on usage.
Max. Loading
Do not overload the
shelves
Shelf Flexing
Remove product if the
shelf is flexing
Shelf Overhang
Do not let product
overhang the shelves
Front
Top
Back
MAX
20kg
per shelf
Internal Airflow
Leave 25mm space
between product and
the back and top of
cabinet interior
Cabinet Floor
Do not load product
on the cabinet floor.
Use the shelves.

ProSpec Series
Routine Cleaning
Ensure the cabinet is unplugged from the power supply before cleaning.
IMPORTANT: Do NOT use abrasive, corrosive or solvent based cleaners, as this could damage the protective coating on
the door exterior.
Wipe the outside of the cabinet with a damp cloth, and the inside of the cabinet with standard stainless steel cleaners
suitable for food preparation areas. Take care to keep moisture away from electrical parts.
The condenser coil must be kept clean. SKOPE strongly recommends monthly cleaning of the condenser coil and air filter.
Do
NOT use hard or sharp tools to clean the coil as these may cause damage.
Service & Support
We know you will get years of satisfaction from your new SKOPE product when you follow a few simple
preventative maintenance guidelines.
Helpful information is available on the SKOPE website
www.skope.com/serviceandsupport
Clean the condenser coil
1. Unplug the cabinet from the power
supply.
2. Remove the front panel from the top
of the cabinet.
3. Brush the condenser coil with a soft
brush to remove any dust and fluff.
4. Refit the front panel and reconnect
the cabinet to the power supply.
IMPORTANT
When refitting, ensure the tabs on
the back of the sign are located in the
notches on top of the cabinet, and
that the sign is pushed fully in and
secure.
Coil
Tab and notch
PRN80218 Rev. 1.1 Sep. 2019