SleepSafe Beds SleepSafe II Medium Bed User manual

!
PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of
safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.
TOOLS NEEDED:
At least 2 People
3/8” Wrench
!
Flat-Head Screwdriver
4mm Allen Wrench
(Provided)
7/16” Wrench
(x2)

!
!
!
!!!
! ! 2!
! !
(Explanation of the Bed Articulation)
(Detailed Instructions for Assembling your Bed)
(Provided Items Necessary for Bed Assembly)
(Detailed Instructions for Adjusting Safety Rails)

!
!
!
!!!
! ! 3!
!
! !
90mm Allen Bolt
Barrel Nut
(Preinstalled on padded beds)
¼” Allen Wrench
T15 Torx Wrench
T10 Torx Wrench
¾“ Hex Bolt
Cardboard Spacer
Black Plugs
4mm Allen Wrench
Locking Pin

!
!
!
!!!
! ! 4!
! !
Casters
Frame
Headboard
Side Rails
Safety Rails
Footboard
Mattress
Crank Handle

!
!
!
!!!
! ! 5!
Determine where your SleepSafe Bed® will be positioned:
Depending on the placement of your bed, it may be necessary to move the Crank Assembly to
the opposite side of the bed. If so, set the frame flat on the ground, remove the Assembly using
your two 7/16” wrenches, and reattach using the color-coded guide below.
* Alternate Crank Assembly position should be a mirror image of its original position.
Set Frame on Cardboard Spacers:
!
One person should lift each side at a time while the
other places the blocks underneath the foundation.
* Be sure to leave room to attach the side rails in the next step.

!
!
!
!!!
! ! 6!
! !
!
Prepare Side-Rails (insert Barrel Nuts):
!
!
Align Barrel Nut Slot Perpendicular to the edge of the Side Rail.
Attach Side Rails to Frame Assembly:
There are two height settings available:
Setting #1 offers 24” of Safety Rail Protection.
Setting #2 offers 18” of Safety Rail Protection.
* Model Shown at Setting #1

!
!
!
!!!
! ! 7!
!
! !
Install Casters and
Remove Spacers:
Attach Headboard and
Footboard to Side Rails:
!
!
* Once the caster is inserted, turn the tightening nut as shown above to compress the
rubber sleeve on the stem inside the wood leg, thus preventing the caster from falling out.

!
!
!
!!!
! ! 8!
! !
Install Mattress:
Install Crank Handles
& Black Plugs:
Locking
Pins
Push Crank Handles onto the Crank Shaft
then insert Locking Pins to hold Handles in place.

!
!
!
!!!
! ! 9!
! !
Install Safety Rails:
!
Operate Your Bed:
Crank the handles
clockwise to articulate
up and counter-
clockwise to articulate
down. The handle by
the headboard is for
Head Articulation and
the handle closest to
the footboard is for
Foot Articulation.
Bed Operation:
HEAD
FOOT
* Always install and remove Safety Rails while they are in the
lowered position.
Installation:
Install the Safety
Rails in the lowered
position by
inserting the black
hex bolt pivot pins
into the plastic
strikes. Once in
place, you may then
tilt the Safety Rails
up into their upright
and locked position.

!
!
!
!!!
! ! 10!
!
!
! !
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
TOOLS NEEDED:
Rubber Mallet
(or Hammer)
T10 Torx Wrench
(Provided)
T15 Torx Wrench
(Provided)
Determine if your Safety Rails need adjustment:
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust the screw up or down depending on
which way you noted in Step 1.
(Clockwise = Up / Counterclockwise = Down)
Remove Plastic Strikes:
Using your T15 Torx Wrench, uscrew the
gold screws holding the strike in place.
Then, use a Rubber Mallet to remove it
from the leg.
Adjust Accordingly:
Reinsert Plastic Strike:
Place the Plastic Strike back into position and
align by gently tapping it with your Rubber
Mallet.
Fig.!2!
Look at each brass locking-pin when the
Safety Rail is in the locked position as
indicated by “A” in Fig. 1. The pin should
be centered in the hole of the plastic
strike. If it is not, note which way the rail
needs to move (up or down).
A!
Centered!
Fig.!1!

!
!
!
!!!
! ! 11!
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
and footboard legs.
The spacing
should be
even!
!
!
Remove Safety Rail and Adjust Accordingly:
If spacing is not even, or there is
too much side-to-side play in the rail,
remove safety rail and turn the black hex
bolt using the ¼”Allen Wrench provided.
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
A"
B"

!
!
!
!!!
! ! 12!
! !
Full One–Year Warranty:
Limited Five-Year Warranty:
The SleepSafe™ Bed is warranted against defects in workmanship or
materials for a period of one year from the date of purchase. SleepSafe
Beds will repair any defective part at no cost to the purchaser.
During the second through fifth years from the date of purchase,
SleepSafe Beds will replace any part found to be defective. Purchaser
shall pay any service and shipping costs related to the replacement of
the defective part.
*Safety Rails are intended to hinder or discourage the possibility of a roll-out. This product does not take the
place of proper client supervision and monitoring. Any modification to the product or its components will
void the warranty and render the product incapable of fulfilling its intended purpose.
Terms and Conditions:
This warranty applies to normal use and does not cover any damage
caused by normal wear, abuse, misuse, mishandling or modification of
the product.

!
!
!
!!!
! ! 13!
! !

!
!
!
!!!
! ! 14!
!