SleepSafe Beds SleepSafer Hi-Lo Safety Bed User manual

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe® Safety Bed. With proper care, your bed will provide years
of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.
TOOLS NEEDED:
At least 2 People
3/8” Wrench
Flat-Head Screwdriver
4mm Allen Wrench
(Provided)
Be sure to run your bed down all the way once a month or multiple resets will be needed.

(Remote Operation)
(Extension/Topper Assembly Guide)
(List of all the Items necessary for your Bed Assembly)
(Detailed Instructions for Assemblying your Bed)
(Detailed Instructions for adjusting Safety Rails)
2

90mm Allen Bolt
Barrel Nut
(Preinstalled on padded beds)
¼” Allen Wrench
4mm Allen Wrench
T15 Torx Wrench
T10 Torx Wrench
¾“ Hex Bolt
Cardboard Spacer
Alignment Pin
3

Casters
Headboard
Back Panels
Safety Rails
Footboard
Mattress
Hi-Lo Electric Frame
Front Panel
4

Set Frame on Cardboard Spacers:
Prepare Side-Rails (insert Barrel Nuts):
Align Barrel Nut Slot Perpendicular to the edge of the Side Rail.
Side-Rails include the Front Panel and one of the Back Panels (the Panel with Bronze Inserts to attach to the frame).
Set Spacers at least 6” away from attachment points to leave room to attach side rails.
5

Attach Side Rails to Frame:
Attach Headboard and
Footboard to Side Rails:
6

Attach Back Panel using Alignment Pins
Note: Place the alignment pins in the
holes at the top of the side panel (Fig.
A) then lower the back panel onto the
pins (Fig. B). After the back panel is in
position, secure with 90mm Allen Bolts
using the 4mm Allen Wrench as you did
in the previous step.
Install Casters &
Remove Spacers:
* Once the caster is inserted, turn the tightening nut as shown above to compress the
rubber sleeve on the stem inside the wood leg, thus preventing the caster from falling out.
7

Install Safety Rails:
* Be sure to run your
Hi-Lo Bed all the way
down once a month
or multiple resets will
be needed!
Install Mattress:
8

4mm Allen Wrench
90mm Allen Bolt
Curved End Piece
Extension Side Rail
Topper
(Optional)
Allen Screws
(w/ Topper Only)
9

Set Extension Side Rails on Top of Legs:
(You will be assembling the Extension upside-down)
Attach Extension Ends to Side Rails:
Attach Ends with Curve Up (smiling) using the 90mm Allem Bolts and 4mm Allen Wrench provided:
*Be sure screens face in as shown
10

Flip Extension Assembly over:
Curve-down (frowning)
If you don’t have a Topper, skip Step #4:
Attach Topper:
Using the Allen Screws included
11

Attach Extension
Set Extension on top of your SleepSafer® Bed. Insert one 90mm Allen Bolt
into each of the holes at the top of the legs and tighten using the 4mm
Allen Wrench provided (Shown by “B” above). Once all Bolts are tight,
your Extension Assembly is complete!
Loosen (but do not remove) Top Bolts on Bed Legs:
Shown as “A” below:
12

*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
TOOLS NEEDED:
Rubber Mallet
(or Hammer)
T10 Torx Wrench
(Provided)
T15 Torx Wrench
(Provided)
Determine if your Safety Rails need adjustment:
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust the screw up or down depending on
which way you noted in Step 1.
(Clockwise = Up / Counterclockwise = Down)
Remove Plastic Strikes:
Using your Hammer or Rubber Mallet,
gently tap the plastic strike out of place
and remove it from the leg.
Adjust Accordingly:
Reinsert Plastic Strike:
Place the Plastic Strike back into position and
align by gently tapping it with your Rubber
Mallet.
Fig. 2
Look at each brass locking-pin when the
Safety Rail is in the locked position as
indicated by “A” in Fig. 1. The pin should
be centered in the hole of the plastic
strike. If it is not, note which way the rail
needs to move (up or down).
A
Centered
Fig. 1
13

*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
and footboard legs.
The spacing
should be
even!
Remove Safety Rail and Adjust Accordingly:
If spacing is not even, or there is
too much side-to-side play in the rail,
remove safety rail and turn the black hex
bolt using the ¼” Allen Wrench provided.
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
A
B
14

REMOTE LOCK OUT PROCEDURE:
PRESS and HOLD BOTH DOWN BUTTONS
on HEAD and FOOT articulation functions
for about 5 seconds. The light on the
remote will flash when it is locked.
To UNLOCK repeat this procedure.
RESET PROCEDURE:
1.
Press and hold the DOWN
button on the HiLo function,
after the bed is down
completely, continue to hold
for 5-10 seconds. You will hear
the control box click.
2. Your bed is now reset and all
functions operate normally.
HiLo Bed Surface
(Up/Down)
Knee & Foot
(Up/Down)
Head
(Up/Down)
15

Full One–Year Warranty:
Limited Five-Year Warranty:
The SleepSafe™ Bed is warranted against defects in workmanship or
materials for a period of one year from the date of purchase. SleepSafe
Beds will repair any defective part at no cost to the
purchaser.
During the second through fifth years from the date of purchase,
SleepSafe Beds will replace any part found to be defective. Purchaser
shall pay any service and shipping costs related to the replacement of
the defective part.
*Safety Rails are intended to hinder or discourage the possibility of a roll-out. This product does not take the
place of proper client supervision and monitoring. Any modification to the product or its components will
void the warranty and render the product incapable of fulfilling its intended purpose.
Terms and Conditions:
This warranty applies to normal use and does not cover any damage
caused by normal wear, abuse, misuse, mishandling or modification of
the product.
16