SleepSafe Beds SleepSafer Fixed User manual

!
!
PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years
of safe use.
Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.
TOOLS NEEDED:
At least 2 People
3/8” Wrench
!
Flat-Head Screwdriver
4mm Allen Wrench
(Provided)
3/8”
Wrench

"
(Extension/Topper Assembly Guide)
(List of all the Items necessary for your Bed Assembly)
(Detailed Instructions for Assemblying your Bed)
(Detailed Instructions for adjusting Safety Rails)

#
! !
#
90mm Allen Bolt
15mm Allen Bolt
Barrel Nut
(Preinstalled on padded beds)
¼” Allen Wrench
4mm Allen Wrench
T15 Torx Wrench
T10 Torx Wrench
Alignment Pin

$
! !
Casters
Aluminum Strikes
Headboard
Back Panels
Safety Rails
Footboard
Mattress
Box Spring \Bunkie Board
Front Panel

%
!
Prepare Side Rails:
!
Attach Side Rails to
Headboard & Footboard
Be sure the Barrel Nut slot perpendicular to the
edge of the Side Rail. You may need a Flathead
Screwdriver to help with the alignment.

&
Install Casters &
Remove Spacers:
Attach Back Panel using Alignment Pins:
Note: Place the alignment pins in
the holes at the top of the side
panel (Fig. A) then lower the back
panel onto the pins (Fig. B). After
the back panel is in position, secure
with 90mm Allen Bolts using the
4mm Allen Wrench as you did in the
previous step.
Attach Back Panel using Alignment Pins:
Attach Back Panel using Alignment Pins:
!
!
* Once the caster is inserted, turn the tightening nut as shown above to compress the
rubber sleeve on the stem inside the wood leg, thus preventing the caster from falling out.

'
Install Bunkie Board/Box Spring and Mattress:
Install Safety Rails:
'
Install Safety Rails:
!
* Always install and remove Safety Rails while in their Lowered position.

(
4mm Allen Wrench
90mm Allen Bolt
Curved End Piece
Extension Side Rail
Topper
(Optional)
Allen Screws
(w/ Topper Only)

)
)
Set Extension Side Rails on Top of Legs:
You will be assembling the Extension upside-down
Attach Extension Ends to Side Rails:
Attach Ends with Curve Up (smiling) using the 90mm Allem Bolts and 4mm Allen Wrench provided:
*Be sure Screens are facing in (as shown)

*+
Flip Extension Assembly over:
Fli
p Extension Assembly over:
Curve-down (frowning)
If you don’t have a Topper, skip Step #4:
Attach Topper:
Using the Allen Screws included
*+
!

**
Loosen Allen Bolts at Top of SleepSafer® Legs:
Loosening the
Allen Bolts before
adding the
Extension allows
for easier
assembly and
tighter fitting. If
you have flip-up
rails, be sure the
proper legs
match up before
tightening all
Allen Bolts.
Assemble SleepSafer®/Extension Combo
Set Extension on top of your SleepSafer® Bed. Insert one 90mm Allen Bolt
into each of the four vacant holes at the top of the legs and tighten using
the 4mm Allen Wrench provided (Shown by “B” above). Tighten all bolts
and your SleepSafer®/Extension Assembly is complete!
Loosen Allen Bolts at Top of SleepSafer® Legs:
Shown at “A” below:

*"
!
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
TOOLS NEEDED:
Rubber Mallet
(or Hammer)
T10 Torx Wrench
(Provided)
T15 Torx Wrench
(Provided)
adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust the screw up or down depending on
which way you noted in Step 1.
(Clockwise = Up / Counterclockwise = Down)
Remove Plastic Strikes:
Using your Hammer or Rubber Mallet,
gently tap the plastic strike out of place
and remove it from the leg.
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust Accordingly:
Reinsert Plastic Strike:
Place the Plastic Strike back into position and
align by gently tapping it with your Rubber
Mallet.
,-./!"!
Remove Plastic Strikes:
Using your Hammer or Rubber Mallet,
Using your Hammer or Rubber Mallet,
gently tap the plastic strike out of place
Look at each brass locking-pin when the
Safety Rail is in the locked position as
indicated by “A” in Fig. 1. The pin should
be centered in the hole of the plastic
strike. If it is not, note which way the rail
needs to move (up or down).
0!
12342526!
,-./!*!

*#
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
and footboard legs.
The spacing
should be
even!
safety rail and the headboard
!
safety rail and the headboard
safety rail and the headboard
safety rail and the headboard
safety rail and the headboard
!
*#
Remove Safety Rail and Adjust Accordingly:
If spacing is not even, or there is
too much side-to-side play in the rail,
remove safety rail and turn the black hex
bolt using the ¼” Allen Wrench provided.
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
!"
#
remove safety rail and turn the black hex
bolt using the
B = Clockwise = Increase Play
B = Clockwise = Increase Play
A =
Counterclockwise = Decrease Play
Counterclockwise = Decrease Play
adjusted at our factory, but it may become necessary to adjust the Safety
Rail height over time.
Safety Rails need adjustment:
With the safety rail in the locked position, check
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
safety rail and the headboard
safety rail and the headboard

*$
Full One–Year Warranty:
Limited Five-Year Warranty:
The SleepSafe™ Bed is warranted against defects in workmanship or
materials for a period of one year from the date of purchase. SleepSafe
Beds will repair any defective part at no cost to the purchaser.
During the second through fifth years from the date of purchase,
SleepSafe Beds will replace any part found to be defective. Purchaser
shall pay any service and shipping costs related to the replacement of
the defective part.
*Safety Rails are intended to hinder or discourage the possibility of a roll-out. This product does not take the
place of proper client supervision and monitoring. Any modification to the product or its components will
void the warranty and render the product incapable of fulfilling its intended purpose.
Terms and Conditions:
This warranty applies to normal use and does not cover any damage
caused by normal wear, abuse, misuse, mishandling or modification of
the product.