Sloan CX Series User manual

INSTALLATION INSTRUCTIONS FOR
SLOAN CX MANUAL CLOSET AND URINAL FLUSHOMETERS
Code No: 0816856
Rev. 2 (8/19)
LIMITED WARRANTY
Sloan Valve Company warrants its Flushometer to be made of rst class materials, free from defects of material or workmanship under
normal use and to perform the service for which they are intended in a thoroughly reliable and efcient manner when properly installed and serviced, for a period of
three (3) years (one year for special nishes) from the date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts
that prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will
be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations that purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of batteries.
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSE-
QUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
1
Manual Closet Flushometers
Model CX 158-1.6
Model CX 158-1.28
Model CX 154-1.6
Model CX 154-1.28
ITEMS INCLUDED (VALVE BOX)
1. Valve Assembly
2. Mud Guard
3. (2) #10-32 x 2 1/2” screws to
secure mud guard
4. (2) 1/4” x 20 x 2” screws to
remove activation assembly
5. Adjustment tool
6 Installation instructions
7. Holder Tool
8. Adjustable tube
9. Outlet connection
10. Elbow
11. Inlet adapter
12. Vacuum Breaker
13. Couplings & gaskets
1. Valve Assembly 2. Mud Guard 3. #10-32
Mud Guard Screws
4. 1/4-20 Activation
Assembly Screws
5. Adjustment
Tool & Holder
8. Adjustable
Tube
9. Outlet
Connection
10. Elbow 11. Inlet
Adapter
12. Vacuum Breaker
Assembly V-651A Kit
13. Couplings & Gaskets
6. Installation
Instructions
PRIOR TO INSTALLATION
TOOLS AND ITEMS REQUIRED FOR INSTALLATION (PROVIDED)
• 9/64” hex wrench • Wall plate depth guide • Adjustment tool
TOOLS AND ITEMS REQUIRED FOR INSTALLATION (NOT PROVIDED)
• Smooth-jawed wrench (at least 2”) • Philips screwdriver • threaded sweat solder adapter
• approximately 15”-18” pipe
Manual Urinal Flushometer
Model CX 198-0.5
Model CX 198-0.25
This valve is designed for new construction or where there is easily accessed plumb-
ing for the xture and valve. This valve is designed for a minimum 6-1/2 inch (165
mm) wall space depth. Distance from the center of the valve (inlet or outlet pipe) to
the nished surface of the wall can vary from 3-1/4” – 4-1/4” (83 – 108 mm).
Wall plate opening must be a minimum of 7-3/8” wide x 8-3/8” tall (187 mm wide
x 213 mm tall) to maximum 7-5/8” wide x 8-5/8” tall (194 mm wide x 219 mm
tall). Mud plate is provided and must accompany valve for proper installation. Mud
plate is removed after wall is nished.
7. Holder Tool

2
ITEMS INCLUDED (WALL PLATE BOX)
1. Wall Plate
2. Button & Bracket assembly
3. (2) #10-32 x 3 1/2” screws to
secure bracket to valve
4 (2) #8-32 x 7/8” screws to
secure plate to Bracket
5. Depth setting tool
6. (4) Plunger, screws &
locking nut
7. Allen Key 9/64"
8. Installation instructions
1. Wall Plate 2. Button & Bracket
assembly
3. Bracket to
valve #10-32
screws
6. Plunger
# 10-32 screws
8. Instructions
5. Depth setting
tool
7. Allen Key
4. Plate to
Bracket #8-32 screws
IMPORTANT:
• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES AND REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
Sloan’s ushometers are designed to operate with 20 to 80 psi (138 to 552 kPa) of water pressure. THE MINIMUM PRESSURE REQUIRED
TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE SELECTED.
Consult xture manufacturer for minimum pressure requirements. Most high efciency water closets require a minimum owing pressure of 25 psi
(172 kPa). Many building codes and the ASME A112.19.2 xture standard list maximum static pressure as 80 PSI (552kPa).
ROUGH-IN URINALS
FIN.WALL
Rear o
f
valve to
f
in. wall
5
.1
5
” -
6
.1
5
”
(
130 mm - 156 mm
)
Inlet
p
i
p
e CL to fin. wall
3
¼
” -
4
¼”
(83 mm - 108 mm)
V
alve
C
L to fixture inlet
12
¼
” - 12
½
”
(311 mm-318 mm)
Valve CL to fixture inlet
o
f
i
x
1
2
¼
” - 12
½
”
”
(311 mm-318 mm)
18
6
¼
” -
6
½
”
(159 mm-165 mm)
1
6
5
2”
(
51 mm
)
openin
g
in wall
MODEL 198
URINAL REAR INLET ACCURACY IS IMPORTANT FOR
WALL OPENING DIMENSIONS.
VALVE MUST BE CENTERED
HORIZONATLLY IN OPENING
WITHIN 1/8". FOR ASSITANCE,
PLEASE CONSULT ROUGH-IN
TEMPLATE.
!!! IMPORTANT !!!
9. Metal C-bracket and
#8-32 screws
THIS PRODUCT CONTAINS
MECHANICAL COMPONENTS
THAT ARE SUBJECT TO NORMAL
WEAR. THESE COMPONENTS
SHOULD BE CHECKED ON A
REGULAR BASIS AND REPLACED
AS NEEDED TO MAINTAIN THE
VALVE’S PERFORMANCE.
!!! IMPORTANT !!!

3
ROUGH-IN CLOSETS
Rough-in for Sloan CX is determined relative to the spud connection for the fixture being used.
I
nlet
p
i
p
e CL to fin. wall
3
¼” -
4
¼”
(
83 mm - 108 mm
)
1½” min.
(38 mm)
1½” (38 mm)
1½” (38 mm)
36”
(914 mm)
1½” (38 mm)
Rear of valve to fin. wall
5.15” - 6.15”
(
130 mm - 156 mm
)
FIN.WALL
ADA GRAB BAR
A
A
DA GRAB BAR
A
DA
G
RAB BAR
7-1/2” (191 mm)
15” (381 mm)
16”-18” (406-457 mm)
36”
(914 mm)
V
alve
C
L to fixture inlet
:
12
¼” -
12
½
”
(311 mm-318 mm)
11“-11
¼
” (279-286 mm)
N
O
TE: I
f
f
ixture inlet i
s
b
e
l
ow r
i
m
l
eve
l
, consu
l
t
floor mount rear inlet
r
ough-in dimensions
Valve CL to fixture inlet:
L
to
f
12
¼” -
1
12
½
”
(
311 mm - 318 mm)
11“-1
1
1(279-286 mm)
¼
”
Fixture inlet to wall opening:
n
let t
o
6
¼
” -
6
½
½
”
1
59 mm - 165 mm)
(1
5“-5
¼” (127-133 mm)
¼
”
(
1
1½” (38 mm)
FIN.WALL
ADA GRAB BAR
A
NO
TE: I
f
f
ixture inlet i
s
a
bove rim level, consult
wall hung rear inlet
rough-in dimensions
I
nlet pipe
C
L to
f
in. wall
3
¼
” -
4
¼
”
(
83 mm - 108 mm)
R
ea
r
o
f v
a
lv
e
t
o
fin. w
a
ll
5
.1
5
” -
6
.1
5
”
(
130 mm - 156 mm)
V
alve
C
L to
f
ixture inlet:
16
½
”
- 16
¾
”
(
419 mm-425 mm
)
1
4
¾
“
-15”
(
375-381 mm
)
Fixture inlet to wall opening:
let t
o
10
½
”
-
10
0
¾
”
(
267 mm-273 mm)
8
¾
“
-
9
2
22-229 mm)” (
2
Valve CL to fixture inlet:
to fi
x
1
6
½
”
- 1
6
6
¾
”
(
419 mm-425 mm)
14
¾
“-
-
1
5
”
(
375-381 mm
)
”
2” (51 mm)
opening in wall
1½” min.
(38 mm)
33” MAX.
(836 mm)
top of plate
33” MAX.
(836 mm)
top of plate
2” (51 mm)
opening in wall
MODEL 158 CLOSET WALL
HUNG REAR INLET
MODEL 154 CLOSE FLOOR
MOUNT REAR INLET
SIDE VIEW
SIDE VIEW FRONT VIEW
FRONT VIEW
THIS PRODUCT CONTAINS
MECHANICAL COMPONENTS
THAT ARE SUBJECT TO NORMAL
WEAR. THESE COMPONENTS
SHOULD BE CHECKED ON A
REGULAR BASIS AND REPLACED
AS NEEDED TO MAINTAIN THE
VALVE’S PERFORMANCE.
!!! IMPORTANT !!!
ACCURACY IS IMPORTANT
FOR WALL OPENING
DIMENSIONS. VALVE
MUST BE CENTERED
HORIZONATLLY IN
OPENING WITHIN 1/8".
FOR ASSITANCE, PLEASE
CONSULT ROUGH-IN
TEMPLATE.
!!! IMPORTANT !!!
ACCURACY IS IMPORTANT
FOR WALL OPENING
DIMENSIONS. VALVE
MUST BE CENTERED
HORIZONATLLY IN
OPENING WITHIN 1/8".
FOR ASSITANCE, PLEASE
CONSULT ROUGH-IN
TEMPLATE.
!!! IMPORTANT !!!

4
PARTS OVERVIEW
Valve Body
Shut-off Sleeve
(integrated control stop)
Piston
Assembly
Conical
Spring
Activation
Assembly
Collar
Activation Assembly
Removal Screws
Adjustment Tool
Flush Volume
Color I.D. Plug
Plunger
Mounting Bracket
Wall Plate
9/64” Hex
Wrench
Anti-vandal screw
Wall Plate to
Mounting Bracket
Button
Mounting
bracket to valve
body screws
Mud Guard
Metal
C-bracket
Plunger Screw
Depth Guide
Plunger
Screws
F-1 Outlet Connection
S-21 Gasket
Poly Washer
F-305 Elbow
Poly
Washer
F-2 Coupling
Adjustable Tube
V500A RB
Vacuum Breaker
Assembly
Vacuum Breaker
Kit V-651A
NOTE: Wall hung closet shown. Consult
pages 7-8 for other configurations.

5
INSTALL OPTIONAL SWEAT SOLDER ADAPTER (ONLY IF YOUR SUPPLY PIPE DOES
NOT HAVE A MALE THREAD)
THREADED
SWEAT ADAPTER
PIPE
AOn a 15”-18” length of pipe (not provided), slide threaded sweat
adapter (not provided) onto water supply pipe until end of pipe rests
against shoulder of adapter. Sweat solder the adapter to pipe
(1" copper x 1" NPT tting).
BRemove mud Guard from valve and save for later use-
DO NOT DISCARD
CInsert sweat adapter into 1 1/2” to 1” threaded adapter (provided).
DConnect 1 1/2” to 1 “ adapter into top of ushometer (“IN”)
Tighten ttings securely into valve body with a xed jaw wrench.
15”-18”
C
D
FUsing a sweat union (not supplied), connect valve assembly to water
supply pipe.
Water Supply
Sweat Union
(not supplied) Sweat Connections
E
NOTE: PROPERLY BRACE SUPPLY PIPE AFTER
SWEATING CONNECTIONS TO PREVENT VALVE
MOVEMENT DURING INSTALLATION AND USE
SLOAN RECOMMENDS BRACING VALVE WITHIN 6"
OF INLET CONNECTION.

AIf needed, trim bottom of adjustable tube using grinding style cut-off
tool.
• NOTE: would only be needed for certain ADA
water closet installations.
• Consult rough-in guide (page 2-3)
As needed based on rough-in, pre-bend the adjustable tube to
account for side-to-side misalignment of water supply pipe relative
to xture spud.
B
Cut as needed
A.
B.
Adjustable Tube
Taper towards
elbow
Coupling
nut
Poly
washer
Elbow
A
B
Cut F-1 ush connection to length as needed for particular rough-in.
• Consult rough-in (pages 2-3)
Connect F-1 ush connection and adjustable tube to the elbow
using coupling and poly washer. Apply Loctite to tube ends, insert
tube ends into elbow, and tight coupling securely. Allow Loctite to
cure for 24 hours before ushing water through valve. Failure to
allow Loctite to cure could result in separation or leaks.
CInsert V-651A vacuum breaker kit into vacuum breaker casing.
Attach to valve hand tight.
Attach ush connection to vacuum breaker hand tight.
D
EFinish wall. Use supplied mud guard to protect valve during nishing
process.
• Use two (2) mounting bracket to valve body screws, if needed,
to hold mud guard to valve body
Vacuum Breaker
Kit V651A
Vacuum Breaker
casing
Flush Connection
Mud Guard
Loosen vacuum breaker assembly to valve and loosen
adjustable tube from V500A RB. Do not disconnect
coupling connections.
Partially mount xture onto carrier nuts.
Pull ush connection forward through wall.
Make spud connection wrench tight.
• NOTE: Space permitting or chase present, spud
connection can be made behind wall.
Push xture back to wall. Tighten carrier bolts and
complete xture installation.
Re-connect vacuum breaker to valve.
MAKING SPUD CONNECTION
F, K
G
J
I
H
FOR WALL HUNG REAR SPUD FIXTURES
(WATER CLOSETS)
6
CONFIGURE ADJUSTABLE TUBE
V500A RB
Loctite must cure
for 24 hours before
turning on water
otherwise the
Loctite will wash
out and joint will
leak
F
G
H
I
J
K
NOTE: Do not trim tube
before pre-bending
Wall plate opening must be a minimum 7-3/8” wide x
8-3/8” tall (187 mm wide x 213 mm tall) to maximum
7-5/8” wide x 8-5/8” tall (194 mm wide x 219 mm tall).
Valve must be centered horizontally within opening.
!!! IMPORTANT !!!

7
Wall opening
FOR FLOOR MOUNT REAR SPUD FIXTURES (WATER CLOSET)
FOR REAR SPUD URINALS
If needed, trim urinal ush tube
Slide 3/4" coupling over urinal ush tube
Thread F-28 brass ange onto urinal ush tube.
Amount of thread engagement will depend on rough-in.
Use provided Loctite to secure F-28 ange in place.
Apply Loctite to tube ends, insert tube ends into
elbow, and tight coupling securely. Allow Loctite
to cure for 24 hours before ushing water through
valve. Failure to allow Loctite to cure could result in
separation or leaks.
Secure urinal ush tube to elbow using 1-1/2” gasket and friction ring.
Hang urinal on mounting bracket
Loosen vacuum breaker to valve
Make spud connection behind the wall.
Re-connect vacuum breaker to valve.
G, I
H
C
F-28 Flange
D
Adjustable Tube
Taper towards
elbow
Coupling nut
Coupling
nut
Poly washer
Elbow
If needed, trim bottom of adjustable tube using grinding style cut-off
tool.
• NOTE: would only be needed for certain ADA
water closet installations.
• Consult rough-in guide (page 2-3)
As needed based on rough-in, pre-bend the adjustable tube to
account for side-to-side misalignment of
water supply pipe relative to xture spud.
Cut as needed
A.
B.
Adjustable Tube
Taper towards
elbow
Coupling
nut
Poly
washer
Elbow
Cut F-1 ush connection to length as needed for particular rough-in.
• Consult rough-in (pages 2-3)
Connect F-1 ush connection and adjustable tube to the elbow using
coupling and poly washer. Apply Loctite to tube ends, insert tube ends
into elbow, and tight coupling securely. Allow Loctite to cure for 24 hours
before ushing water through valve. Failure to allow Loctite to cure could
result in separation or leaks.
Install mud guard. Finish wall.
Mount xture.
Loosen vacuum breaker to valve. Pull ush
connection forward through opening in wall.
Pre-install escutcheon and ttings in the
following order:
1.Wall trim plate
2.Coupling
3.Friction Ring
4.Gasket
5.Escutcheon
Connect coupling (2) to spud, wrench tight.
Slide wall trim plate against wall.
Re-connect vacuum breaker to valve.
H
5 4 32 1
G, J
Loctite must cure
for 24 hours before
turning on water
otherwise the
Loctite will wash
out and joint will
leak
Loctite must cure
for 24 hours before
turning on water
otherwise the
Loctite will wash
out and joint will
leak
A
B
C
D
G
H
E
F
I
J
A
B
D
CI
H
G
F
E
NOTE: Do not trim tube
before pre-bending

8
FLUSHING WATER LINES
Note: Valve is shipped with flow adjustment turned off.
AShut off water: use adjustment tool to turn activation assembly fully
clockwise.
BRelieve pressure by pressing plunger. Push in activation assembly.
CSqueeze tabs on Collar and pull out.
DAttached provided 1/4-20 screws to activation assembly. Pull to
remove assembly
ERemove conical spring. Do not discard!
Remove piston assembly by pulling straight out. If unable to grip
piston, remove screw from activation assembly and insert into
center hole of piston.
F
Reinstall activation assembly and press until fully seated. Remove
screws.
CLOSE
B1
B1
C1
C2
D
F
E
G
Reinstall Collar. Collar will spin freely in valve body when properly
installed.
G1
G2
H
Using adjustment tool, turn activation assembly counter clockwise to
open ow of water through the valve.
Once lines are ushed clear, turn activation assembly clockwise to
shut off water.
Push in activation assembly.
Squeeze tabs on Collar and pull out.
Attach provided screws to activation assembly. Pull to remove.
I
J
K
M
L
CLOSE
K
L1
L2
Reinstall piston. Insert smaller sized end rst until fully seated.
Reinstall conical spring, small end rst, into piston.
Reinstall activation assembly and press until fully seated.
Reinstall orange collar securely. Collar will spin freely in valve body
when properly installed.
Adjust ow rate of valve as described on page 9.
N
O
P
Q
R
N
O
P
Q
OPEN

9
ADJUSTING FLOW
AUsing adjustment tool, turn activation assembly slowly to adjust ow.
BPush plunger to activate ush. Adjust water ow as needed to clean the xture.
B
A
CLOSE
OPEN
THE FLUSHOMETER IS ENGINEERED FOR
QUIET OPERATION. EXCESSIVE WATER
FLOW CREATES NOISE, WHILE TOO
LITTLE WATER FLOW MAY NOT SATISFY
THE NEEDS OF THE FIXTURE. PROPER
ADJUSTMENT IS MADE WHEN PLUMBING
FIXTURE IS CLEANSED AFTER EACH FLUSH
WITHOUT SPLASHING WATER OUT FORM
THE LIP AND A QUIET FLUSHING CYCLE IS
ACHIEVED.
IMPORTANT
INSTALL WALL PLATE ASSEMBLY
Loosen set screw with provided 9/64” Allen hex key until button is
free to rotate upward. Lock into position.
Remove face plate and set aside
A
B
C
D
Mount wall bracket to wall, tilting to insert metal C-bracket
through wall opening.
Insert #10-32 mounting screws through wall bracket.
Attach to top mounting holes on valve body.
BA2 A1
Wall Bracket
Metal C-bracket
D D
D
i.There is approximately 1/8-turn (45°) of free spinning as the activation
assembly engages the shut-off sleeve between opening and closing
the valve.
ii. 1-1/2" socket or wrench can be attached to the adjustment tool or
a screwdriver can be passed through the side side holes to provide
additional torque.
NOTE: If desired, orange flow
adjustment tool can be attached
to valve assembly using supplied
mounting hanger

10
INSTALL WALL PLATE ASSEMBLY (CONT.)
Tighten #8-32 screws at bottom of wall bracket. Metal C-bracket
will clamp against wall.
E
E
E
E2
Slide wall plate over button. Button will pass through top of
opening.
Insert #8-32 wall plate to mounting bracket screws into wall plate.
Tighten to secure to wall bracket.
F
G
G1
G1
G2
G2
H
I
J
K
Choose one of three Plunger screws and nut provided and thread
into plunger. If Plunger starts rotating, STOP. This means the
screw has reached the bottom of the hole and overtightening the
screw will cause damage to the plunger. Try the next shorter screw
included with the product to nish adjustment.
Using depth guide provided, adjust depth of Plunger screw until
screw touches depth guide and secure with nut.
Fold down button
Secure set screw using provide Allen key. Button should not be tight
against screw attached to Plunger. NOTE: take care when tightening
screw - Allen key can scratch nish of the wall plate.
Test ush by pushing button. Make sure button is not pushing
screw when in resting position.
L
J
R
H
I
IMPORTANT: If button is tight to the screw when
at rest, intermittent valve flushing may occur.

Open wall plate
i. Loosen set screw using 9/64 allen key
ii. Lift button until it snaps into the "up" position
Remove wall plate. Loosen two screws, pull forward.
Note: water can be shut-off without removing wall plate. Removing wall plate provides
more hand room for servicing valve.
Shut off water: use adjustment tool to turn activation assembly fully clockwise.
Relieve pressure by pressing plunger. Push in activation assembly.
Squeeze tabs on Collar and pull out.
Attach provided 1/4-20 screws to activation assembly. Pull to remove assembly.
Remove conical spring. Do not discard!
Remove piston assembly by pulling straight out. If unable to grip piston, remove 1/4-20 screw
from activation assembly and insert into center hole of piston.
Reinstall or replace piston. Insert smaller sized end rst until fully seated.
Reinstall or replace conical spring, small end rst, into piston.
Reinstall or replace activation assembly and press until fully seated.
Reinstall orange safety ring securely. Safety ring will spin freely in valve body when
properly installed
Turn on water: use adjustment tool to turn activation assembly counter clockwise. See "Adjusting Flow" section for further details.
BASIC SERVICING
CLOSE
A
E
F
G
H
I
J
K
L
B
C
D
11
M
NOTE: Using screws attached to
activation assembly, pull
activation assembly forward to
ensure proper alignment.

TROUBLESHOOTING GUIDE
1. Flushometer does not function (no water/flush).
A. Ensure water supply to valve is turned on.
B. Shut off sleeve is in closed position. Turn counterclockwise to open water ow. NOTE: There is approximately 1/8-turn (45°) of free spinning as
the activation assembly engages the shut-off sleeve between opening and closing the valve.
C. Plunger screw is not adjusted properly. Adjust screw using depth guide. NOTE: Activation button should be held one (1) second for optimal
performance.
2. Volume of water is not sufficient to evacuate the bowl.
A. Shut off sleeve is not open wide enough. Adjust shut off sleeve for desired delivery of water volume.
B. Urinal piston parts installed in a Closet ushometer. Replace piston with proper Closet piston (1.6 gpf/6.0 Lpf or 1.28 gpf/4.8 Lpf)
C. Water supply volume or pressure is inadequate (low). If the xture does not siphon or evacuate the bowl, steps must be taken to increase the
water supply pressure and/or volume. Contact the xture manufacturer for minimum water supply requirements of the xture.
D. Plunger screw is not adjusted properly. Adjust screw using depth guide.NOTE: Activation button should be held one (1) second for optimal perfor-
mance.
3. Flushometer closes off immediately.
A. Urinal piston parts installed in a Closet ushometer. Replace piston with proper Closet piston (1.6 gpf/6.0 Lpf or 1.28/4.8 Lpf).
B. Piston lip seal may be damaged or worn. Replace with new correct gpf/Lpf piston.
C. Plunger screw not set properly. Adjust screw using depth guide.
4. Length of flush is too short (Short Flush).
A. Incorrect piston is installed in Flushometer; for instance, Urinal assembly inside a Closet Flushometer,
or High Efciency assembly inside a higher consumption xture. Determine the ush volume required by the xture and replace with proper gpf/
Lpf piston. Use valve label and markings on xture for reference.
B. Piston lip seal may be damaged or worn. Replace with new correct gpf/Lpf piston.
C. Plunger screw is not adjusted properly. Adjust screw using depth guide.
5. Length of flush is too long (Long Flush) or continuous.
A. Metering bypass hole in piston is clogged. Remove the piston from the valve, slide o ring off lter, and wash under clean running water.
Reposition o-ring before reinstalling piston. Replace piston if cleaning does not correct the problem.
B. Supply line water pressure has dropped and is not sufcient to close the valve. Close shut off sleeve until pressure is restored. NOTE: under
some conditions, opening the shut-off sleeve can correct the force imbalance and cause the valve to close.
D. Piston is damaged. Replace with new proper gpf/Lpf piston
E. Incorrect Piston is installed in Flushometer; for instance, Closet assembly inside a Urinal ushometer. Determine the ush volume required by the
xture and replace piston. Use valve label and markings on xture for reference.
6. Chattering noise is heard during flush.
A. Reduce ow pressure by turning shut off sleeve clockwise.
B. Air trapped inside the valve and/or supply pipe. Air takes time-both count of ushes and actual duration - to be fully removed.
CARE AND CLEANING
DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Flushometers that may dull the luster and attack the chrome or special
decorative nishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Flushometer
from any splattering of cleaner. Acids and cleaning uids will discolor or remove chrome plating.
12

1
2
3
410
5
4
8
7Install with
Flange against spud
For Model 8158, Wall Hung For Model 8154, Floor Mount
9
4
For Model 8198
11
6
VALVE ASSEMBLY GUIDE
1
2
SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131
Phone: [phone] or 1.847.671.4300 • Fax: [phone] or 1.847.671.4380 • sloan.com
COPYRIGHT © 2019 SLOAN VALVE COMPANY Code No: 0816856 – Rev. 2 (8/19)
Item No. Part No. Description
1 Consult Factory Piston Assembly
2 See Table Activation Assembly
Code No. Description Plug Color*
3340048 1.6 gpf/6.0 Lpf closet activation assembly Green
3340049 1.28 gpf/4.8 Lpf closet activation assembly Purple
3340051 0.5 gpf/1.9 Lpf urinal activation assembly Red
3340052 0.25 gpf/1.0 Lpf urinal activation assembly Burgundy
ACTIVATION ASSEMBLY SELECTION GUIDE
* Colors may differ. Consult factory to conrm you have the correct activation assembly.
Item Code No. Description
1 3323182 V-651A Vacuum Breaker Repair Kit
2 0323279 V-500A RB Vacuum Breaker Assembly
30306391
0306367
Adjustable Tube for Wall Hung Closets and Urinals
Adjustable Tube for Floor Mount Closets
4 0306395 CX Poly Washer Coupling (set of 2)
5 0306392PK F-305 CX Elbow for CX Poly Washer
6 0306091 F-2-A 1-1/2" Coupling with S-21 Gasket
7 0306031PO F-1 1 1/2" (38 mm) Flanged outlet tube RB, 6"
8 0396669PK F-102 1-1/2" (38 mm) Outlet Tube CP 8"*
9 0306238PK F-7 Flange CP*
10 0306146PK F-5-A 1-1/2" Spud Coupling Assembly CP*
11 0306396 CX Urinal Connection
FLUSH CONNECTION PARTS
Plug
The information contained in this document is subject to change without notice.
Manufactured in the U.S.A by Sloan Valve Company under one or
more of the following patents: U.S. Patents. 5,295,655; 5,542,718;
5,558,120; 5,564,460; 5,730,415; 5,865,420; 5,887,848;
5,967,182. Other Patents Pending.
Bak-Chek®, Para-o®, PERMEX®, Turbo-Flo®
13
* Consult factory for alternate nish options
IN ORDER FOR THE WATER CLOSET AND THE URINAL TO PERFORM PROPERLY FOR ITS INTENDED USE, YOU MUST FOLLOW THESE INSTRUCTIONS:
A. IDENTIFY YOUR FLUSHOMETER MODEL NO.
B. CHECK FOR THE WATER CONSUMPTION LABEL ATTACHED TO THE FLUSHOMETER AND FIXTURE, ENSURING THEY MATCH
C. REFER TO SPECIFIC FLUSHOMETER SECTION IN GUIDE FOR APPROPRIATE REPLACEMENT PART NO.
Tech Support: 1.888.756.2614 or 1.888.SLOAN14