Sloan Optima ETF-600 User manual

Code No. 0816318
Rev. 2 (08/10)
IN TALLATION IN TRUCTION FOR
EN OR ACTIVATED ETF-600/610 LAVATORY FAUCET
L M TED WARRANTY
Sloan Valve Company warrants its ETF-600 and ETF-610 Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform
the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three (3) years (one (1) year for special
finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan
Valve Company, at customer's cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This
warranty extends only to persons or organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale.
THERE ARE NO WARRANT ES WH CH EXTEND BEYOND THE DESCR PT ON ON THE FACE HEREOF. N NO EVENT S SLOAN VALVE COMPANY RESPONS BLE FOR ANY CONSEQUENT AL DAMAGES OF ANY
MEASURE WHATSOEVER.
Prior to installing the Sloan ETF-600 or ETF-610 Faucet, install the items
listed below. Refer to Rough-in illustrations on Page 2.
•When Using Plug- n Transformer — nstall electrical receptacle for plug-
in transformer (120 VAC, 2 amp service for each ETF-233 (24 VAC,
35 VA) plug-in transformer used).
•When Using Box Mount Transformer — nstall electrical wiring to
transformer location (120 VAC, 2 amp service for each EL-248-40
(24 VAC, 40 VA) transformer used).
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or tempered water supply line
Multiple Faucets
Multiple faucets can be powered by a single transformer, provided that the
transformer has been properly sized. Allow a minimum of 15 VA of current
rating for each solenoid valve used. Refer to “Step 4 — nstall Transformer”
for further information.
Mixing Valve
When installing the faucet with a Sloan mixing valve, these nstallation
nstructions AND the nstallation nstructions packaged with the mixing valve
MUST be followed.
mportant:
•
NSTALL ALL ELECTR CAL W R NG N ACCORDANCE W TH
NAT ONAL/LOCAL CODES AND REGULAT ONS.
•NSTALL ALL PLUMB NG N ACCORDANCE W TH APPL CABLE CODES
AND REGULAT ONS.
•A 24 VAC STEP-DOWN TRANSFORMER MUST BE USED.
•USE APPROPR ATE PRECAUT ONS WH LE CONNECT NG TRANSFORMER
TO 120 VAC POWER SOURCE.
•DO NOT PLUG TRANSFORMER NTO POWER SOURCE (RECEPTACLE)
UNT L ALL W R NG S COMPLETED. ALLOW NG 24 VAC TRANSFORMER
W RES TO TOUCH OR SHORT WH LE POWER S BE NG SUPPL ED W LL
CAUSE PERMANENT DAMAGE TO THE TRANSFORMER AND C RCU T
CONTROL MODULE.
•KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT
COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON
COMPRESS ON F TT NGS. FOR THREADED P PE F TT NGS, DO NOT
APPLY SEALANT TO THE F RST TWO “STARTER” THREADS.
•FLUSH ALL WATER L NES UNT L WATER S CLEAR BEFORE CONNECT NG
SOLENO D TO SUPPLY STOPS.
DO NOT NSTALL THE SPRAY HEAD UNT L AFTER THE SUPPLY L NES HAVE
BEEN FLUSHED.
Model ETF-600
24 VAC, Sensor Activated, 4” Centerset
Lavatory Faucet
Model ETF-610
24 VAC, Sensor Activated
Pedestal Lavatory Faucet
PRIOR TO IN TALLATION
BAK-CHEK®TEE U AGE
When connecting the Sloan ETF-600 or ETF-610 Faucet to both hot and cold water supplies, a Bak-Chek®Tee is provided and required as illustrated in the
Rough-in drawings on Page 2. Water temperature can be controlled by adjusting the supply stops.
When connecting the faucet to a single line water supply or a pre-tempered water supply, a Bak-Chek®Tee is not required.
A Bak-Chek®Tee is not required or provided when a Temperature Mixing Valve is included with the faucet.
TOOL REQUIRED FOR IN TALLATION
• Open end wrenches for hex sizes: 1”, 5/8”,
9/16”, 1/2”
• Slotted screwdriver, 3/16”
• Basin wrench
• Slotted screwdriver (supplied)
• Phillips head screwdriver, #2
• Pliers
• Wire stripper/crimping tool

2
FAUCET ROUGH-IN
1A - IN TALL ETF-600 FAUCET
ETF-600 Faucet with Bak-Chek®Tee
for Hot and Cold Water Supply †
ETF-610 Faucet with Bak-Chek®Tee for Hot and
Cold Water Supply (shown with 4” trim plate) ‡
ETF-610 Faucet with BDM and BDT Variation Mixing
Valves for Hot and Cold Water Supply
(shown with 4” trim plate) ‡
ETF-610 Faucet with ADM Variation Mixing Valve for
Hot & Cold Water Supply (shown with 8” trim plate) ‡
FAUCET
MOUNT NG
STUDS
1/8” NPT P PE
N PPLE
SLOTTED
MOUNT NG
WASHERS (2)
W NG NUTS (2)
SENSOR
CABLE
BASE GASKET
Note: Refer to the nstallation nstructions included with the
ETF-578-A Trim Plate for additional information about using an
8" Trim Plate with an ETF-600 faucet.
Apply thread sealant or Teflon tape to threads at end of Faucet
Pipe Nipple. nstall 1/8" Pipe x 3/8” Tube Compression Fitting on
end of Faucet Pipe Nipple.
D
ASlide Base Gasket onto
Faucet.
nsert Faucet Sensor
Cable, Pipe Nipple, and
Mounting Studs through
the 4” (102 mm) spread
deck holes.
B
Secure Faucet to deck using Slotted Mounting Washers and Wing
Nuts supplied.
C
ETF-600 Faucet
ETF-610 Faucet
1/8” NPT P PE TO 3/8” TUBE
COMPRESS ON F TT NG
ETF-600 Faucet with BDM and BDT Variation
Mixing Valves for Hot and Cold Water Supply †

3
AConnect 3/8” O.D. Supply Tube between Compression Fitting on
outlet side of Solenoid Valve and Compression Fitting on Spout’s
Pipe Nipple or Water Supply Tube.
Note: Flow direction of Solenoid Valve is indicated by arrow on Valve Body.
3 - CONNECT UPPLY LINE( )
Note: Sloan Valve Company recommends that this faucet be installed with
our trim plate. Our trim plate includes an anti-rotation feature to prevent
rotary motion of this single-hole pedestal-style faucet.
SENSOR
CABLE
Apply thread sealant or Teflon tape to threads at end of Faucet
Water Supply Tube. nstall 1/4" Pipe x 3/8” Tube Compression
Fitting on end of Faucet Water Supply Tube.
D
ASlide Base Gasket over Faucet Water Supply Tube and Sensor
Cable. nstall optional Trim Plate, then Trim Plate Gasket.
Holding Faucet Base Gasket and optional Trim Plate assembly in
place, insert Sensor Cable and Faucet Water Supply Tube through
the 1" (25 mm) center hole in deck or lavatory. Use plumber’s putty
to secure optional Trim Plate.
B
Thread Sensor Cable
through side of
Mounting Spacer.
Secure Faucet to
deck or lavatory using
Flat Washer,
Lockwasher and
Mounting Nut.
CFAUCET
BASE
GASKET
MOUNT NG
SPACER
FLAT
WASHER
LOCKWASHER
MOUNT NG
NUT
1/4” NPT P PE TO
3/8” TUBE
COMPRESS ON
F TT NG
1/4” NPT
WATER
SUPPLY TUBE
1/8” P PE N PPLE
SOLENO D VALVE
1/8” P PE TO 3/8” TUBE
COMPRESS ON F TT NG
3/8” SUPPLY TUBE
(NOT SUPPL ED)
1/4” WATER
SUPPLY TUBE
3/8” BAK-CHEK®
COMPRESS ON TEE
(FOR APPL CAT ONS US NG
DUAL WATER SUPPLY)
SOLENO D VALVE
1/4” P PE TO 3/8” TUBE
COMPRESS ON F TT NG
3/8” SUPPLY TUBE
(NOT SUPPL ED)
3/8” BAK-CHEK®
COMPRESS ON TEE
(FOR APPL CAT ONS US NG
DUAL WATER SUPPLY)
ETF-600
ETF-610
3/8” (10 mm)
SUPPLY TUBE
3/8” (10 mm)
COMPRESS ON
F TT NG
SOLENO D
VALVE
SUPPLY
STOP
BFor Single Line Water Supply Applications
nstall a 3/8 inch (10 mm) copper supply
tube between the supply stop and inlet side
of Solenoid Valve. (Supply stop and copper
supply tube furnished by installer.) Tighten
Compression Fittings securely.
mportant: Keep thread sealant out of your waterway and prevent
component part damage! Do not use sealant on compression fittings.
When thread sealant is used, do not apply it to the first two “starter”
threads.
mportant: Flush dirt, debris, and sediment
from the supply line(s).
1B - IN TALL ETF-610 FAUCET
3/8” (10 mm)
COMPRESS ON
F TT NG
3/8” (10 mm)
SUPPLY TUBE
SOLENO D
VALVE
SUPPLY
STOP
For Dual Line Hot and Cold Water Supply
Applications
nstall a 3/8 inch (10 mm) copper supply
tube between Bak-Chek®Compression
Tee and hot and cold supply stops.
(Supply stops and copper supply tube
furnished by installer.) nstall a 3/8 inch
(10 mm) copper supply tube between
Bak-Chek®Compression Tee and inlet
side of Solenoid Valve. Tighten
Compression Fittings securely.
Note: Failure to install the Bak-Chek®Tee
can result in a cross flow connection
when the faucet is off and the supply
stops are open. f pressure of the
hot and cold water supply differ, hot
water can migrate into the cold water
supply or vice-versa. Most plumbing
codes require that the Bak-Chek®be used
to prevent this.
A
2 - IN TALL OLENOID VALVE
3/8” (10 mm)
BAK-CHEK®TEE
USED ON DUAL
WATER SUPPLY
APPL CAT ONS
ONLY

4
Multiple Faucets
Multiple faucets can be powered by a single transformer that has been properly
sized. Allow a minimum of 15 VA of current rating for each solenoid valve used.
Refer to the following example to determine the required current rating for 3
OPT MA faucets.
Example:
Total number of OPT MA faucets: 3
Total number of solenoid valves: 3
Multiply by current rating: 15 VA
——
Minimum current rating of required transformer: 45 VA
Transformers Available with the ETF-600 and ETF-610 Faucets
Standard Plug- n † ETF-233 120 VAC 35 VA
Standard Box Mount EL-248-40 120 VAC 40 VA
† n Canada, use ETF-416 (120 VAC, 35 VA).
Optional Transformers Available from Sloan
Box Mount EL-154 120 VAC 50 VA
Foot Mount EL-208 120 VAC 100 VA
Box Mount EL-342 240 VAC 50 VA
All Sloan transformers are 50/60 Hz.
Other transformers (not supplied by Sloan) may be used, provided they meet UL
requirements for Class 2 transformers.
mportant: DO NOT supply power to primary side of Transformer until all
wiring has been completed.
Mount Transformer on a metal electrical junction box (supplied by others).
(“J” box should be mounted inside chase wall or above ceiling.) nstall
Transformer within 50 feet (15.24 meters) of Faucet.
18 gauge wire is recommended.
ARun wires from secondary side of Transformer to 3/8 inch (10 mm)
hole at back of Control Module Enclosure. f necessary, wires can be
run through wall and then inserted through hole in back of Control
Module Enclosure.
mportant: DO NOT plug Transformer into receptacle until all wiring has been
completed.
The Transformer is supplied with a 10 foot Cable; however, this Cable can and
should be shortened to meet installation requirements.
AStrip ends of Transformer Power Cable approximately 3/16 to 1/4
inch (5 to 6 mm).
Bnstall Strain Relief 3 inches (76 mm) from one end of Power Cable.
mportant: Twist stranded ends of Power Cable before inserting into Terminal
Block. Fraying of Stranded Power Cable Wire can cause a short and damage
the Control Module and Transformer when powered.
Enstall Crimp Connectors and connect Power Cable ends to
Transformer Terminals.
120 VAC
PR MARY
24 VAC
SECONDARY
BOX MOUNT
TRANSFORMER
(EL-248-40
SHOWN)
PLUG- N TRANSFORMER
TRANSFORMER
TERM NALS
CR MP CONNECTORS
POWER CABLE
PLUG- N
TRANSFORMER
(ETF-233 SHOWN)
CONTROL
MODULE
BASE
STRA N REL EF
DConnect Power Cable to Terminal Block on Connector Board. See
Step 6.
Cnsert Power Cable and Strain Relief into hole at back of Control
Module. nstall right angle Strain Relief so that Power Cable enters
the Control Module from the bottom.
4 - IN TALL TRAN FORMER
4A - IN TALL BOX MOUNT TRAN FORMER
4B - IN TALL PLUG-IN TRANFORMER

5
Anstall the Control Module in an appropriate location as shown in
Rough-in. Control Module must be installed so that all cables enter
from the bottom of the unit. When installed, Cables from the Spout
and Solenoid Valve to the Control Module should have some slack.
ARoute Cables from Solenoid Valve and Spout to the Control Module.
Cnsert Locking Connector from Faucet Spout into mating
Receptacle on Connector Board. Allow 3 to 4 inches (76 to 102
mm) of Cable to extend into the Control Module.
BMount Control Module to wall using Mounting Screws and Plastic
Anchors.
EXTENS ON CABLES
Extension Cables are available as an option from Sloan to allow for
installing the Control Module remote from the Faucet Spout and Solenoid
Valve. Refer to the Parts List for available lengths.
4” (102 mm)
CONTROL
MODULE
ENCLOSURE
FROM SOLENO D
VALVE
FROM TRANSFORMER
STRA N REL EF SLOTS
FROM FAUCET SPOUT
TERM NAL BLOCK -
1. REMOVE TERM NAL
BLOCK
2. NSERT POWER
CABLES
3. SECURE W TH
SCREWS
4. RE NSTALL
TERM NAL BLOCK
CONNECTOR
BOARD
POWER
CABLE
MODULAR
RECEPTACLE
Bnsert Solenoid Valve Connector into the Modular Receptacle on
Connector Board.
Dnsert each Conduit Cable into a strain relief slot in the Control
Module.
APlug Transformer into 120 VAC Receptacle.
Note: The Control Module is equipped with two LED lights. When power is
supplied by the Transformer, one LED will illuminate green. When Sensor is
activated, this LED will change to red. A second red LED illuminates when
Solenoid Valve is activated.
BOpen Supply Stop(s). With Aerator removed, activate Faucet for 30
seconds by placing hands in front of Sensor. The Solenoid Valve
should “click” and water should flow from the Spout. f this does
not occur, refer to the Troubleshooting section of this instruction
instructions.
CClose Supply Stop(s) and install Spray Head in Spout using the Key
provided. Reopen Supply Stop(s), activate Faucet and check for
leaks.
TRANSFORMER
5 - MOUNT CONTROL MODULE TO WALL
6 - CONNECT CONTROL MODULE CONNECTION
7 - PLUG IN TRAN FORMER AND TART-UP
RANGE ADJ.
SCREW –
SEE STEP 8

6
The OPT MA ETF-600 and ETF-610 Faucets are factory set to operate
when hands are placed 4 to 5 inches (102 to 127 mm) from Sensor. This
range should be satisfactory for most installations.
f range adjustment is required, refer to the following range adjustment
procedures.
TO MAKE A RANGE ADJUSTMENT
The Range Potentiometer and Dip Switches are located in Control Module.
mportant: Range Potentiometer adjustment screw rotates only 3/4 of a
turn; DO NOT over-rotate.
Make certain that Dip Switch number 4 is in the UP position. Using the
small screwdriver provided, adjust Range Potentiometer clockwise until
green (power ON) indicator LED turns red (Faucet is now picking up sink).
Adjust Range Potentiometer back counterclockwise until red LED returns
to green. Range is now at maximum.
Cycle Faucet several times to assure that range as adjusted will not
inadvertently pick up R reflection in lavatory. f R reflection occurs (green
LED will flicker red), adjust Range Potentiometer counterclockwise very
slightly and again cycle Faucet.
Repeat range adjustment counterclockwise until length of range is at bowl
rim of lavatory (plus or minus 1” (25 mm)).
Time Out Adjustment
The Faucet Time Out Setting determines the maximum time the Faucet
will run upon continuous activation. This timing can be changed to meet
individual application requirements.
Refer to Table 1 or label on cover of Control Module along with the
following instructions to set the desired Time Out. The Dip Switches used
to set the Time Out are located in the Control Module.
Set the Time Out by configuring the number 1, 2 and 3 Dip Switches as
shown in Table 1.
Table 1 — Time Out Settings
Unless otherwise specified, all ETF-600/ETF-610 Faucets leave the
factory set with a 30 second Time Out.
Note: The position of Dip Switch # 4 (range enhancer setting) does not
affect Faucet Time Outs.
Push Cables into slots at the bottom of the Control Module.
nstall Control Module Cover using Screws provided. Refer to illustration in
Step 6.
Time Out Dip Switch Setting
Switch #1 Switch #2 Switch #3
3 SECONDS UPUPDOWN
6 SECONDS DOWN DOWN UP
12 SECONDS UP DOWN UP
30 SECONDS UP DOWN DOWN
45 SECONDS UPUPUP
1 M NUTE DOWN UPUP
3 M NUTES DOWN DOWN DOWN
20 M NUTES DOWN UP DOWN
1. A continuous
invisible beam of
infrared light is
emitted from the
OPT MA sensor
located at the base
of the lavatory
faucet.
2. As the user’s
hands enter the
beam’s effective
range (beneath
the spray head),
the beam is
reflected back
into the sensor
receiver and activates the solenoid valve.
Tempered water flows from the faucet into
the sink until the hands are removed from
the beam or until the faucet reaches an
automatic time out limit setting.
3. When hands
are moved
away from the
sensor, the loss
of reflected
light initiates an
electrical signal
that deactivates
the solenoid valve, shutting off the water
flow. The circuit then automatically resets
and is ready for the next user.
DO NOT use abrasive or chemical cleaners (including chlorine bleach)
to clean faucets that may dull the luster and attack the chrome or
special decorative finishes. Use ONLY soap and water, then wipe dry
with clean cloth or towel.
When cleaning the bathroom tile, protect the faucet from any
splattering of cleaner. Acids and cleaning fluids will discolor or remove
chrome plating.
8 - RANGE ADJU TMENT
TE T FAUCET OPERATION
CARE AND CLEANING OF CHROME AND PECIAL FINI HE

7
Note: Remove Cover from Control Module to check diagnostic lights.
1. PROBLEM: No water is delivered when Faucet is activated.
ND CATOR: f no LED lights illuminate:
CAUSE: No electricity is being supplied to Faucet.
SOLUT ON: Ensure that the main power is turned “ON.” Check all
Transformer, Sensor, Solenoid and Cable Connections. Make
sure that Transformer is supplying 24 VAC (Volts AC). f no
voltage is detected, replace Transformer.
CAUSE: There is an electrical system malfunction.
SOLUT ON: Reset electrical system. Unplug Sensor Connection.
Disconnect power to circuit for ten (10) seconds. Reconnect.
ND CATOR: f the GREEN LED does NOT illuminate when power is
reconnected:
CAUSE: There is an electrical system malfunction.
SOLUT ON: Reset electrical system. Unplug Sensor Connection.
Disconnect power to circuit for ten (10) seconds. Reconnect.
CAUSE: The Control Module circuit is “dead.”
SOLUT ON: Replace ETF-450-A Control Module.
ND CATOR: f GREEN LED illuminates AND changes to RED when hands
are in the Sensor’s detection zone AND the RED Solenoid LED illuminates:
CAUSE: Water supply stop(s) may be partially closed.
SOLUT ON: Open supply stop(s) completely.
CAUSE: Debris is clogging Solenoid Filter.
SOLUT ON: Shut off water supply. Remove, clean and reinstall Solenoid
Filter.
ND CATOR: f GREEN LED illuminates AND changes to RED when hands
are placed in the Sensor’s detection zone AND the RED Solenoid LED
flickers with a vibrating/clicking noise heard inside the module:
CAUSE: There is a direct short in the Solenoid or Solenoid Cable.
SOLUT ON: Replace with ETF-370-A Solenoid.
ND CATOR: f GREEN/RED LED illuminates AND changes to RED when
hands are NOT located in the Sensor’s detection zone BUT the RED
Solenoid LED (in upper left corner of circuit) does NOT illuminate:
CAUSE: Sensor range is set too long and is detecting the sink.
SOLUT ON: Reduce Sensor detection range.
CAUSE: Sensor is faulty.
SOLUT ON: Replace Sensor.
ND CATOR: f GREEN LED illuminates BUT does NOT change to RED
when hands are placed in the Sensor’s detection zone:
CAUSE: Sensor range is set too short.
SOLUT ON: ncrease Sensor detection range.
CAUSE: Sensor is faulty.
SOLUT ON: Replace Sensor.
2. PROBLEM: Sensing Range is too short.
CAUSE: Extended Range Sensitivity is required.
SOLUT ON: Dip Switch number 4 should be in the “DOWN” (Extended
Range Sensitivity) position. ncrease range by adjusting Range
Potentiometer clockwise (yellow phillips screw in blue base).
3. PROBLEM: Faucet activates by itself (false triggers).
CAUSE: Sensor range is set too long.
SOLUT ON: Decrease range by adjusting Range Potentiometer
counterclockwise. f necessary, flip Dip Switch number 4 to
the “UP” (Reduced Range Sensitivity) position. Check
surroundings for factors that contribute to Sensor range
detection problems (bright lights, highly reflective surfaces,
sunlight, etc.).
4. PROBLEM: Faucet delivers very low flow or just a dribble.
CAUSE: Water supply stop(s) may be partially closed.
SOLUT ON: Open supply stop(s) completely.
CAUSE: Debris is clogging Solenoid Filter.
SOLUT ON: Shut off water. Remove, clean, and reinstall Solenoid Filter or
install Solenoid Valve repair kit ETF-1009-A.
CAUSE: Solenoid is worn or faulty.
SOLUT ON: Rebuild with ETF-1009-A Solenoid Repair Kit or replace ETF-
370-A Solenoid.
CAUSE: Debris is clogging Faucet Aerator or Spray Head.
SOLUT ON:Shut off water. Remove Aerator or Spray Head (use Key if
required). Clean and reinstall Aerator or Spray Head.
5. PROBLEM: Faucet does not stop delivering water or continues to drip
after user is no longer detected (even after power to the Module has been
disconnected).
CAUSE: Solenoid Valve is installed backward.
SOLUT ON: Disconnect Solenoid. Reconnect Solenoid with water flow
toward the Faucet (see arrow on Solenoid).
CAUSE: Debris is clogging Solenoid.
SOLUT ON: Remove and clean Solenoid Operator. f necessary, rebuild
with ETF-1009-A Repair Kit.
CAUSE: Seat in Solenoid Valve body is damaged or pitted.
SOLUT ON: Replace with ETF-370-A Solenoid.
When assistance is required, please contact Sloan Valve Company
nstallation Engineering Department at:
1-888-SLOAN-14 (1-888-756-2614)
TROUBLE HOOTING GUIDE

SLOAN VALVE COMPANY • 10500 Seymour Avenue • Franklin Park, L 60131
Phone: [phone] or 1-847-671-4300 • Fax: [phone] or 1-847-671-4380
www.sloanvalve.com
Copyright © 2010 SLOAN VALVE COMPANY Rev. 2 (08/10)
ETF-600
1A
4A
ETF-610
4B
2
1B
2
5A
5B
7
12
11
10
9
6
13B
13A
15
14 16
tem Part Description
No. No.
1A ETF-543-A Faucet Spout and Sensor Assembly (ETF-600)
1B ETF-570-A Pedestal Faucet Spout and Sensor Assembly (ETF-610)
2 ETF-1023-A 0.5 gpm (1.9 Lpm) Spray Head with Key (male thread)
ETF-1024-A 2.2 gpm (8.3 Lpm) Aerator Spray Head with Key (male thread)
ETF-1029-A 2.2 gpm (8.3 Lpm) Laminar Flow Spray Head (male thread)
3 ETF-435 Replacement Key Only for ETF-1023-A Spray Head and
ETF-1024-A Aerator Spray Head
4A ETF-546-A Faucet Mounting Kit for ETF-600 includes: Base Gasket, two (2)
Slotted Mounting Washers, two (2) Wing Nuts, and ETF-547
Compression Fitting Connector
4B EBF-123-A Faucet Mounting Kit for ETF-610 includes: Spacer, Base Gasket,
1/4” NPSM Hex Nut, Washer, 9/16” Lockwasher, Compression
Fitting Connector
5A ETF-547 1/8” NPT Pipe to 3/8” Tube Compression Fitting Connector
(ETF-600)
5B EBF-129 1/4” NPT Pipe to 3/8” Tube Compression Fitting Connector
(ETF-610)
6 ETF-617-A 3/8” Bak-Chek®Tee Compression Fitting
7 ETF-370-A 24 VAC Solenoid Valve Assembly, includes Wire Harness
8 ETF-437-A Assembly Kit, includes: Compression Fittings (2), Compression Nut
(1), Compression Sleeve (1)
9 ETF-450-A Control Module Assembly
10 ETF-233 Plug- n Transformer
11 EL-248-40 Box Mount Transformer
12 ETF-458-A Power Cable with Strain Relief and Crimp Connectors (Transformer
to Control Module)
OPT ONAL TR M PLATES
13A ETF-607-A 4” (102 mm) Centerset Single-hole Trim Plate Kit for ETF-610
Faucet
13B ETF-608-A 8” (203 mm) Centerset Single-hole Trim Plate Kit for ETF-610
Faucet
— M X-102-A 4” (102 mm) Centerset Double-hole Trim Plate Kit for ETF-610
Faucet with Optional Mixing Valve
— M X-106-A 8” (203 mm) Centerset Double-hole Trim Plate Kit for ETF-610
Faucet with Optional Mixing Valve
— ETF-578-A 8” (203 mm) Centerset Single-hole Trim Plate Kit for ETF-600
Faucet
— ETF-577-A 8” (203 mm) Centerset Double-hole Trim Plate Kit for ETF-600
Faucet with Optional Mixing Valve
33
tem Part Description
No. No.
OPT ONAL M X NG VALVES
14 M X-60-A Below Deck Mechanical Water Mixing Valve (BDM Variation)
15 M X-135-A Below Deck Thermostatic Water Mixing Valve (BDT Variation)
16 M X-110-AA Optimix®Deck Mounted Water Mixing Valve (ADM Variation)
(only available for ETF-610 faucet)
FAUCET CABLE EXTENS ON CORDS
Faucet to Control Module Solenoid to Control Module
ETF-1005-26 26” (0.7 meter) Length ETF-1003-36 36” (0.9 meter) Length
ETF-1005-36 36” (0.9 meter) Length ETF-1003-48 48” (1.2 meter) Length
ETF-1005-72 72” (1.8 meter) Length ETF-1003-72 72” (1.8 meter) Length
ETF-1005-108 108” (2.7 meter) Length ETF-1003-108108” (2.7 meter) Length
SOLENO D VALVE REPA R K T
— ETF-1009-A ncludes replacement Filter
For additional information about Sloan Mixing Valves or Trim Plates, consult our
nstallation nstructions and Maintenance Guides.
f further assistance is required, please contact the Sloan Valve Company nstallation
Engineering Department at:
1-888-SLOAN-14 (1-888-756-2614)
The information contained in this document is subject to change without notice.
8
8
PART LI T

Code No. 0816321
Rev. 3 (08/10)
INS ALLA ION INS RUC IONS FOR BA ERY POWERED
SENSOR AC IVA ED LAVA ORY FAUCE S
L M TED WARRANTY
Sloan Valve Company warrants its EBF-615 and EBF-650 Faucets to be made of first class materials, free from defects of material or workmanship under normal
use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three
years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove
to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed
for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from
Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANT ES WH CH EXTEND BEYOND THE DESCR PT ON ON THE FACE HEREOF. N NO EVENT S SLOAN VALVE COMPANY RESPONS BLE FOR
ANY CONSEQUENT AL DAMAGES OF ANY MEASURE WHATSOEVER.
PRIOR O INS ALLA ION
EBF-615
Pedestal,
Battery Powered,
Sensor Activated
Lavatory Faucet
EBF-650
4” Centerset,
Battery Powered,
Sensor Activated
Lavatory Faucet
Prior to installing the Sloan EBF-615 or EBF-650 faucet, install the items listed below. Also, refer to rough-in illustrations on Page 2.
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or tempered water supply line
Mixing Valve
When installing the faucet with a Sloan Mixing Valve, these nstallation nstructions AND the nstallation nstructions packaged with the Mixing Valve
MUST be followed.
mportant:
•
ALL PLUMB NG S TO BE NSTALLED N ACCORDANCE W TH APPL CABLE CODES AND REGULAT ONS.
•KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON COMPRESS ON
F TT NGS. FOR THREADED P PE F TT NGS, DO NOT APPLY SEALANT TO THE F RST TWO “STARTER” THREADS.
•FLUSH ALL WATER L NES UNT L WATER S CLEAR BEFORE CONNECT NG SOLENO D TO SUPPLY STOPS.
DO NOT NSTALL THE BATTER ES UNT L THE FAUCET S COMPLETELY NSTALLED. f batteries are installed before sensor cable is connected to control module, the
faucet will not properly set the sensing range for the sink on which it is installed.
OOLS REQUIRED FOR INS ALLA ION
• Open end wrenches for the following hex sizes: 1/2”, 9/16”, 5/8”,
11/16”, 1”
• Basin wrench
• Phillips head screwdriver, #2
• Hammer (if installing plastic or hollow wall anchors to mount the
control module)
• Pliers
• 1/4" drill bit (if installing plastic wall anchors to mount the
control module)
• 5/16" drill bit (if installing hollow wall anchors to mount the
control module)
• 3/8" drill bit (if installing toggle nut anchors to mount control module)
Bak-Chek®Tee Usage
When connecting the EBF-615 or EBF-650 faucet to both hot and cold water supplies, a Bak-Chek®Tee is provided and required as illustrated in
Step 3. Water temperature can be controlled by adjusting the supply stops. When connecting the faucet to a single line water supply or a pre-
tempered water supply, a Bak-Chek®Tee is not required. A Bak-Chek®Tee is not required or provided when a Temperature Mixing Valve is included
with the faucet.

FAUCE ROUGH-IN
Anstall Faucet Spout as shown. Use plumber’s putty to secure optional
Trim Plate, if used.
mportant: After installing Mounting Nut, apply thread sealant or Teflon
tape to threads of Water Supply Tube.
Sloan Valve Company recommends installation of our trim plate with anti-
rotation feature to prevent rotation of this single-hole pedestal-style faucet.
2
EBF-615 Faucet with Bak-Chek®Tee for Hot and
Cold Water Supply (shown with 4” trim plate)
EBF-615 Faucet with ADM Variation Mixing Valve for
Hot and Cold Water Supply (shown with 8” trim Plate)
EBF-615 Faucet with BDM and BDT Variation
Mixing Valves for Hot and Cold Water Supply
(shown with 4” trim Plate)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL) ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL) ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL) ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
EBF-650 Faucet with Bak-Chek®Tee
for Hot and Cold Water Supply
EBF-650 Faucet with BDM and BDT Variation Mixing
Valves for Hot and Cold Water Supply
FAUCET
1/4” NPT
WATER SUPPLY
TUBE BASE GASKET
FAUCET SENSOR CABLE
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL) ADAPTER
(OPTIONAL)
FAUCET S DE V EW
EBF-615
ADAPTER
(OPTIONAL)
ADAPTER
(OPTIONAL)
EBF-650
APPLY THREAD SEALANT
AFTER NSTALL NG
MOUNT NG NUT
SPACER
APPLY PLUMBER’S
PUTTY AROUND EDGE
MOUNT NG SPACER
FLAT WASHER
LOCKWASHER
MOUNT NG NUT
1/4” NPT P PE TO 3/8” TUBE
COMPRESS ON F TT NG
TR M PLATE
(OPT ONAL)
1A - Install Faucet Spout and Optional rim Plate — EBF-615

3
1B - Install Faucet Spout — EBF-650
Anstall Faucet Spout as shown.
mportant: Apply thread sealant or Teflon tape to threads of Water
Supply Pipe Nipple.
Refer to the nstallation nstructions included with the ETF-578-A Trim Plate
for additional information about using an 8" Trim Plate with an EBF-650
faucet.
FAUCET
1/8” NPT P PE N PPLE
BASE GASKET
FAUCET SENSOR CABLE
APPLY THREAD SEALANT
SLOTTED MOUNT NG
WASHERS (2)
W NG NUTS (2)
1/8” NPT P PE TO 3/8” TUBE
COMPRESS ON F TT NG
2 - Install Solenoid Valve
Anstall 3/8 inch (10 mm) supply tube (furnished by installer) between
the Compression Fittings on Spout and the top outlet of Solenoid Valve.
Flow direction of Solenoid Valve is indicated by an arrow on Valve Body.
3/8” (10 mm) SOLENO D
VALVE COMPRESS ON
F TT NG (TOP OUTLET)
3/8” (10 mm) SUPPLY TUBE
(NOT SUPPL ED)
3/8” (10 mm)
COMPRESS ON F TT NG
Model
EBF-615
Shown
3 - Connect Supply Line(s) from Supply Stop(s) to Solenoid Valve Inlet
Dual Line Hot and Cold Water
Supply Applications
nstall a 3/8 inch (10 mm) copper supply tube
between Bak-Chek®Compression Tee and hot
and cold supply stops. (Supply tubes and stops
furnished by installer.) nstall a 3/8 inch (10 mm)
copper supply tube between Bak-Chek
Compression Tee and inlet side of Solenoid
Valve. Tighten Compression Fittings securely.
Note: Failure to install the Bak-Chek®Tee can
result in a cross flow connection when the
faucet is off and the supply stops are
open. f pressure of the hot and cold water
supply differ, hot water can migrate into
the cold water supply or vice-versa.
Most plumbing codes require that the
Bak-Chek®be used to prevent this.
3/8” (10 mm)
BAK-CHEK TEE USED
ON DUAL WATER
SUPPLY
APPL CAT ONS
ONLY
3/8” (10 mm)
COMPRESS ON
F TT NG
3/8” (10 mm)
SUPPLY TUBE
SOLENO D
VALVE
SUPPLY
STOP
A
3/8” (10 mm)
COMPRESS ON
F TT NG
3/8” (10 mm)
SUPPLY TUBE
SOLENO D
VALVE
SUPPLY
STOP
BSingle Line Water Supply Applications
nstall a 3/8 inch (10 mm) copper supply tube
between the supply stop and inlet side of
Solenoid Valve. (Supply tube and supply stop
furnished by installer.) Tighten Compression
Fittings securely.
mportant: Keep thread sealant out of your waterway and prevent component
part damage! Do not use sealant on compression fittings. When thread
sealant is used, do not apply it to the first two “starter” threads.
mportant: Flush dirt, debris, and sediment from the supply line(s).

6 - Install Batteries
4
BATTERY
COMPARTMENT
CONTROL MODULE
Ansert four (4) AA-size Alkaline Batteries provided as indicated by the
(+) and (—) symbols inside the Battery Compartment.
4 - Mount Control Module to Wall
5 - Control Module Connection
Bnsert Locking Connector from Solenoid Valve into mating Receptacle.
Cnsert Connector from Faucet Spout into Modular Receptacle.
Ensert each Cable into a Strain Relief Slot.
BMount Control Module to wall using Mounting Screws and Plastic
Anchors.
Anstall the Control Module in an appropriate location. Control Module
must be installed so that all cables enter from the bottom of the unit.
When installed, Cables from the Spout and Solenoid Valve to the
Control Module should have some slack.
ARoute Cables from Solenoid Valve and Spout to the Control Module. CONTROL
MODULE
ENCLOSURE
FROM SOLENO D VALVE
FROM ADAPTER
STRA N
REL EF
SLOTS
FROM FAUCET SPOUT
POWER CABLE
JACK
4” (102 mm)
MODULAR
RECEPTACLE
LOCK NG
CONNECTOR
FOUR (4) AA-S ZE ALKAL NE BATTER ES
Dnsert Power Cable Jack from Adapter (optional) into Receptacle.
7 - Plug in Adapter (Optional)
APlug Adapter into Receptacle. ADAPTER
(OPT ONAL)

Activate ( "dry fire") Faucet by placing hands in front of the Sensor. The
Solenoid Valve should “click.” Once hands are removed the Solenoid
Valve should click again. f this does not occur, refer to the
Troubleshooting section of this instruction manual.
Once "dry firing" segment is complete, remove spray head. Open
supply stop(s) then activate
Faucet by placing hands in
front of the Sensor. The
Solenoid Valve should
"click" and water should
flow from the Spout.
8 - Start-Up
BActivate Faucet for 30 seconds by placing hands in front of the Sensor.
The Solenoid Valve should “click” and water should flow from the
Spout. f this does not occur, refer to the Troubleshooting section of this
instruction manual.
A
5
CClose supply stop(s) and reinstall Spray Head in Spout using the Key
provided. Reopen supply stop(s), activate Faucet and check for leaks.
9 - Range Adjustment
AThe Range Potentiometer is located in the Control Module.
mportant: Range Potentiometer adjustment screw rotates only 3/4 of a turn;
DO NOT over-rotate. Over-rotating will damage range adjustment screw.
CONTROL MODULE
RANGE
POTENT OMETER
A SCREWDR VER S PROV DED ON
THE NS DE COVER OF THE
CONTROL MODULE FOR MAK NG
RANGE ADJUSTMENTS
The OPT MA Plus EBF-615 and EBF-650 Faucets are factory set to
operate when hands are placed 4 to 5 inches (102 to 127 mm) from
Sensor. This range should be satisfactory for most installations. f
range adjustment is required, refer to the following range adjustment
procedure.
BCycle Faucet several times to assure that the Sensor will not
inadvertently pick up reflection off the edge of the sink. f reflection
occurs, adjust Range Potentiometer counterclockwise very slightly and
again cycle Faucet.
Repeat adjustment procedure until desired range is achieved.
10 - Noise Reduction (NR) and ime Out (Mode) Jumper Settings
T ME OUT (MODE) JUMPER
NO SE REDUCT ON (NR) JUMPER
For jumper settings, refer to Table below or label on cover of Control
Module along with the instructions in this Step.
Noise Reduction (NR) Setting
• When operating the faucet on batteries alone, set the NR jumper to
bridge pins 1 and 2.
• When operating the faucet using the plug-in adapter with battery
backup, bridge pins 2 and 3.
Time Out (Mode) Setting
The Faucet Time Out Setting determines the maximum time the
Faucet will run upon continuous activation. This timing can be
changed to meet individual application requirements.
Unless otherwise specified, Faucets leave the factory set with a 30
second Time Out.
DESCR PT ON P NS
1 2 3
NO SE REDUCT ON (NR) SETT NG
Normal Operation
(Adapter w/Battery Backup Operation)
NR Enabled
(Battery Operation Only)
T ME OUT (MODE) SETT NG
13.75 Second On Demand
30 Second On Demand

1. A continuous
invisible beam of
infrared light is
emitted from the
sensor located on
the throat of the
lavatory faucet.
2. As the user’s
hands enter the
beam’s effective
range (beneath
the spray head),
the beam is
reflected back
into the sensor receiver and activates the
solenoid valve. Tempered water flows from
the faucet into the sink until the hands are
removed from the beam or until the faucet
reaches an automatic time out limit setting.
3 When hands are
moved away
from the sensor,
the loss of
reflected light
initiates an
electrical signal
that deactivates the solenoid valve, shutting
off the water flow. The circuit then
automatically resets and is ready for the
next user.
6
Battery Replacement Procedure (Water does not need to be turned off)
Care and Cleaning
DO NOT USE abrasive or chemical cleaners (including chlorine bleach)
to clean faucets as they may dull the luster and attack the chrome or
special decorative finishes. Use ONLY soap and water, then wipe dry
with clean cloth or towel.
While cleaning the bathroom tile, the faucet should be protected from
any splattering of cleaner. Acids and cleaning fluids will discolor or
remove chrome plating.
The Sloan Optima
Plus EBF-615 and EBF-650 faucets are furnished
with four (4) AA-size alkaline batteries that provide up to two (2) years
of operation (8000 cycles per month). A flashing LED signal indicates
that battery power will be depleted within one (1) month.
CReinstall Cover. Refer to
Step 11.
BRemove old batteries and
insert four (4) new AA-size
Alkaline Batteries as
indicated by the (+) and
(—) symbols inside the
Battery Compartment.
ARemove Cover as follows:
1. Remove the two (2)
Cover Screws.
2. Press in the middle of
both sides.
3. Pull Cover straight out
from Control Module
Base.
1
2
2
3
Operation
11 - Install Cover onto Control Module
Anstall Cover over the Control Module making sure that all four (4)
locking tabs snap into place. Secure using the two (2) screws provided.
Cover can be installed in only one orientation.
CONTROL MODULE
CONTROL MODULE
COVER
COVER SCREW (2)
LOCK NG TAB (4)

roubleshooting Guide
7
Solenoid Screen Filter Cleaning Procedure
ATurn off water supply at supply stop(s). Activate Faucet to relieve
system pressure.
BRemove Water Supply Line from nlet Side of Solenoid Valve. Remove
Cap, Water Line Fitting, Gasket, Filter Housing and Filter from Solenoid
Valve Housing.
CSlide Filter off Filter Housing. Clean Filter using fresh tap water only. f
necessary, use a small brush to clean. Use caution while cleaning to
prevent damage to Filter.
f any Filter components are damaged, replace as necessary. Examine
the Gasket for wear or damage; replace if necessary.
DReinstall Filter on Filter Housing.
nstall Filter Housing, Gasket, Water Line Fitting and Cap onto Solenoid
Valve Housing.
Tighten Cap securely.
F LTER
EReinstall Water supply Line to nlet Side of Solenoid Valve.
NLET S DE OF SOLENO D VALVE HOUS NG
F LTER HOUS NG
WATER L NE F TT NG
GASKET
CAP
When assistance is required, please contact your local Sloan
Representative or Sloan Valve Company nstallation Engineering
Department at:
1-888-SLOAN-14 (1-888-756-2614)
1. PROBLEM: Sensor LED does not function (indicator light on sensor window
in faucet spout does not flash during initial 10 minute set-up
mode).
CAUSE: There is no visible indicator light. Normal operation.
SOLUT ON: This is a normal operating feature of the faucet.
2. PROBLEM: Faucet does not deliver any water when Sensor is activated.
ND CATOR: Solenoid valve produces audible “CL CK.”
CAUSE: Water supply stop(s) closed.
SOLUT ON: Open supply stop(s) completely.
ND CATOR: Solenoid valve DOES NOT produce an audible “CL CK.”
CAUSE: Solenoid Lead is not properly connected to the Control Module.
SOLUT ON: Disconnect and reconnect Solenoid Lead to the Control Module.
CAUSE: No battery or Transformer (optional) power is being supplied to
Sensor.
SOLUT ON: Ensure that the batteries are installed properly. Check that the
orientation of each battery matches the positive (+) and negative
(—) symbols shown on the bottom of the battery compartment.
Reinsert the Batteries into the Control Module. Transformer
(optional) is unplugged or wall receptacle has no power.
CAUSE: Sensor Cable is not properly connected to the Control Module.
SOLUT ON: Disconnect and reconnect Sensor Cable to the Control Module.
CAUSE: Sensor range is set at minimum distance.
SOLUT ON: ncrease Sensor range. Refer to Step 9, Range Adjustment.
CAUSE: Control Module assembly is defective.
SOLUT ON: Replace Control Module assembly.
3. PROBLEM: Faucet delivers only a slow flow or dribble when Sensor is
activated.
CAUSE: Water supply stop(s) partially closed.
SOLUT ON: Open supply stop(s) completely.
CAUSE: Solenoid Filter is clogged.
SOLUT ON: Remove, clean and reinstall Filter. Refer to Solenoid Screen Filter
Cleaning Procedure on Page 6. Replace with new Solenoid Filter
Kit if necessary.
CAUSE: Aerator is clogged.
SOLUT ON: Remove, clean and reinstall Aerator.
4. PROBLEM: Faucet does not stop delivering water or continues to drip after
user is no longer detected (automatic shut-off fails even when
batteries are removed).
CAUSE: Solenoid Valve has been connected backwards.
SOLUT ON: Disconnect Solenoid Valve compression fittings at both the inlet
and outlet positions. The water should flow from inlet through the
Solenoid Valve to the outlet according to the direction of the
arrow shown on the side of the Solenoid Valve. Reconnect the
compression fittings in the correct orientation.
CAUSE: Solenoid Valve is dirty.
SOLUT ON: Backflush by reversing water flow (opposite to the direction
shown by the arrow on the side of the Solenoid Valve) through
the Solenoid Valve. Reconnect the compression fittings in the
correct orientation. Activate faucet.
CAUSE: Solenoid Valve Module is defective.
SOLUT ON: Replace Solenoid Valve Module.
5. PROBLEM: The water temperature is too hot or too cold on a faucet
connected to hot and cold supply lines with Bak-Chek Tee.
CAUSE: Supply stops are not adjusted properly.
SOLUT ON: Adjust supply stops.
NOTE: For some systems, a Thermostatic Mixing Valve may be required.
6. PROBLEM: The Red LED turns on in the control module (below deck).
CAUSE: One (or more) of the batteries is “dead.”
SOLUT ON: To ensure proper operation, insert four (4) new AA-size Alkaline
batteries. Check that the orientation of each battery matches the
positive (+) and negative (—) symbols shown on the bottom of
the battery compartment. Reinsert Batteries into the Control
Module.
CONTROL
MODULE
ENCLOSURE
FROM SOLENO D VALVE
FROM OPT ONAL
ADAPTER
STRA N
REL EF
SLOTS
FROM FAUCET SPOUT
POWER CABLE
JACK
MODULAR
RECEPTACLE
LOCK NG
CONNECTOR

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKL N PARK, L 60131
Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: [phone] or 1-847-671-4380
www.sloanvalve.com
Copyright © 2010 SLOAN VALVE COMPANY Rev. 3 (08/10)
The information contained in this document is subject to change without notice.
LL
OO
DD
C
C
H
H
OO
TT
tem Part Description
No. No.
1A ETF-755-A CP Faucet Assembly 4” Centerset (ETF-650)
1B EBF-120-A Pedestal Faucet Spout and Sensor Assembly ( EBF-615 )
—
ETF-749-A Sensor Only
2
ETF-1023-A 0.5 gpm (1.9 Lpm) Spray Head with Key (male thread)
ETF-1024-A 2.2 gpm (8.3 Lpm) Aerator Spray Head with Key
(male thread)
F-174 CP Spray Head 0.5 gpm Laminar Flow Spray Head
(male thread)
3
ETF-435 Replacement Key Only for ETF-1023-A 0.5 gpm (1.9 Lpm)
Spray Head and
ETF-1024-A 2.2 gpm (8.3 Lpm) Aerator
Spray Head (NOT required for
F-175- L 2.2 gpm/8.3 Lpm
Laminar Flow Spray Head)
4A
ETF-546-A Faucet Mounting Kit for EBF-650 includes Base Gasket,
two (2) Slotted Mounting Washers, two (2) Wing Nuts and
ETF-547 Compression Fitting Connector
4B
EBF-123-A Faucet Mounting Kit for EBF-615 includes Base Gasket,
Spacer, Washer, 9/16” Lockwasher, 1/4” NPSM Hex Nut
and
ETF-547 Compression Fitting Connector
5
ETF-547 1/8” NPT Pipe to 3/8” Tube Compression Fitting Connector
(female)
6
ETF-617-A 3/8” Bak-Chek®Tee Compression Fitting
7
ETF-740-A 6 VDC Solenoid Assembly
8
ETF-735-A Control Module
—
ETF-736 Control Module Replacement Gasket (two required)
L
O
D
C
H
O
T
EBF-615
1A
4A
EBF-650
2
3
5
1B
2
6
11A 11B
12
13
14
3
4B
7
PAR S LIS
8
9
10
tem Part Description
No. No.
9 SFP-6 110 VAC/6 VDC Plug-in Adapter (optional)
10
ETF-443-A Hardwired Mounting Kit (optional)
—
EBF-113 Compression Fitting Kit (optional) includes:
ETF-209 2 compression nuts
ETF-208 2 ferrules
ETF-91 1 plastic screwdriver
OPT ONAL TR M PLATES
11A ETF-607-A 4" (102 mm) Centerset Single-hole Trim Plate Kit for
EBF-615 Faucet (Faucet only)
11B
ETF-608-A 8" (204 mm) Centerset Single-hole Trim Plate Kit for
EBF-615 Faucet (Faucet only)
OPT ONAL M X NG VALVES
12 M X-60-A Below Deck Mechanical Water Mixing Valve
(BDM Variation)
13
M X-135-A Below Deck Thermostatic Water Mixing Valve
(BDT Variation)
14
M X-110-AA Optimix®Deck Mounted Water Mixing Valve (only available
for
EBF-615 faucets)
For additional information about Sloan Mixing Valves or Trim Plates, consult our
nstallation nstructions and Maintenance Guides.

INSTALLATION INST UCTIONS
FO EBF-625/EBF-655
SENSO ACTIVATED FAUCETS
Code No: 9108237
Rev. 3 (12/10)
OPTIMA FAUCETS
MODELS
EBF-625
EBF-655
Battery Powered,
Sensor Activated
Lavatory Faucets
EBF-625
EBF-655
Installation of the Sloan Optima Plus EBF-625 or EBF-655 Battery
Powered, Sensor Activated Faucet makes wash-up totally “hands free”
providing the ultimate in sanitary protection and automatic operation.
The Optima Plus faucet uses infrared technology to sense the user’s
presence and turn on a water supply that has been pre-mixed to the
desired water temperature. When the user’s hands are removed from
the invisible beam of light, the water supply automatically turns off.
In addition, the faucet is powered by four (4) “C” batteries which
eliminates the need to run any electrical lines to the system.
The Sloan EBF-625 or EBF-655 battery powered, sensor activated
faucet comes complete with an integral faucet and sensor assembly,
control module, alkaline batteries, and all mounting hardware.
Bak-cheks and a grid strainer are also available as optional equipment.
The installer should supply 3/8” copper supply tube or exible hose
connections.
The following instructions serve as a guide when installing the Sloan
EBF-625 or EBF-655 faucet. As always, good safety practices and care
when installing your new faucet.
If further assistance is required, contact your nearest
Sloan Representative ofce or the Sloan Installation
Engineering Department at 1-888-SLOAN-14.
LIMITED WARRANTY
Sloan Valve Company warrants its EBF-625 and EBF-655 faucets to be made of rst class materials, free from defects of material or workmanship under normal
use and to perform the service for which they are intended in a thoroughly reliable and efcient manner when properly installed and serviced, for a period of
three (3) years (one (1) year for special nishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or
parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty.
No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve
Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY
CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

OUGH-INS
SPOUT
WING NUT AND
SLOTTEDWASHER
BASE GASKET
†
‡
† ‡
1/8" NPT PIPE TO 3/8" TUBE
COMPRESSION FITTING
1/8" PIPE NIPPLE
3/8" COMPRESSION
FITTING
3/8" COMPRESSION FITTING
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
3/8" COPPER
SUPPLY TUBES
(NOT SUPPLIED)
SOLENOID VALVE
EBF-655 FAUCETWITHDUAL LINE WATER SUPPLY
1" (25 mm)minimumdiameter hole required to mount faucet shank on deck.
3/8" (10 mm)minimumdiameter clearance for mounting studs.
3/8" COMPRESSION STOPS (NOT SUPPLIED)
BAK CHEK
3/8" COMPRESSION TEE
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
CONTROL MODULE
3/8" COMPRESSION STOP OR
MIXING VALVE (NOT SUPPLIED)
SPOUT
WING NUT AND
SLOTTED WASHER
CONTROL MODULE
BASE GASKET
1/8" NPT PIPETO3/8" TUBE
COMPRESSION FITTING
1/8" PIPE NIPPLE
3/8" COMPRESSION
FITTING
3/8" COMPRESSION FITTING
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
3/8" COPPER
SUPPLY TUBE
(NOT SUPPLIED)
SOLENOIDVALVE
EBF-655FAUCETWITHSINGLE LINE WATER SUPPLY
† ‡
EBF-625 FAUCET WITH SINGLE LINE WATER SUPPLY
3/8" COMPRESSION STOP OR
MIXING VALVE (NOT SUPPLIED)
SPOUT
WING NUT AND
SLOTTED WASHER
1/4" NPT PIPETO3/8" TUBE
COMPRESSION FITTING
SPACER, FLAT WASHER,
LOCK WASHER AND NUT
3/8" COMPRESSION
FITTING
3/8" COMPRESSION FITTING
CONTROL MODULE
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
3/8" COPPER
SUPPLY TUBE
(NOT SUPPLIED)
SOLENOIDVALVE
BASE GASKET
EBF-625 FAUCET WITH DUAL LINE WATER SUPPLY
1/4" NPT PIPE TO 3/8" TUBE
COMPRESSION FITTING
SPACER, FLAT WASHER,
LOCK WASHER AND NUT
3/8" COMPRESSION
FITTING
3/8" COMPRESSION FITTING
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
3/8" COPPER
SUPPLY TUBES
(NOT SUPPLIED)
SOLENOID VALVE
3/8" COPPER SUPPLY
TUBE (NOT SUPPLIED)
CONTROL MODULE
BASE GASKET
SPOUT
3/8" COMPRESSION STOPS (NOT SUPPLIED)
BAK CHEK
3/8" COMPRESSION TEE

OUGH-INS (CONTINUED)
EBF-625 FAUCETWITHBOTH DUAL AND SINGLE LINE WATER SUPPLIES
TOTAL LENGTH OF
SENSOR CABLE IS
24" (610 mm)
3-1/2"
(89 mm)
2-1/2"
(64 mm)
2-3/4" (70 mm)
5-1/4"
(133 mm)
3/4" (19 mm)
2" (51mm)
1-1/4" (32 mm)
12o
4-1/2"
(114 mm)
3-1/2" (89 mm)
EBF-655 FAUCETWITHBOTH DUAL AND SINGLE LINE WATER SUPPLIES
TOTAL LENGTH OF
SENSOR CABLE IS
23" (584 mm)
3-1/2"
(89 mm)
2-1/2"
(64 mm)
2-3/4" (70 mm)
5-1/4"
(133 mm)
3/4" (19 mm)
2" (51 mm)
1-1/4" (32 mm)
12o
4-1/2"
(114 mm)
3-1/2" (89 mm)
P IO TO INSTALLATION
Prior to installing the Sloan EBF-625 or EBF-655 faucet, install the items listed
below.
• Lavatory/Sink
• Drain Line
• Hot Water and Cold Water OR Tempered Water Supply Lines
IMPORTANT:
•
ALL PLUMBING IS TO BE INSSTALLED IN ACCORDANCE WITH
APPLICABLE CODES AND REGULATIONS
•
FLUSH ALL WATER LINES PRIOR TO MA ING CONNECTIONS
MIXING VALVE
When installation includes one of Sloan’s Mixing Valve, these instructions AND
those included with the mixing valve MUST be followed.
The Sloan EBF-625 and EBF-655 battery powered sensor activated faucets can
be supplied with two Bak-Cheks. When connecting the faucet to a hot and cold
water supply, two Bak-Cheks are required. Water temperature can be con-
trolled by adjusting the supply stops. When connecting the faucet to a single
line water supply or a pre-tempered water supply, a Bak-Chek is not required.
1 - INSTALL BAK-CHEK TEE (OPTIONAL)
The Sloan Bak-Chek is designed for installation on a 3/8” supply stop.
If an existing stop is used, the stop may require replacement or additional
ttings not supplied by Sloan for connection of the Bak-Chek to the hot
and cold water supply lines. Supply stops should be furnished by the
installer.
After ushing the water supply lines through the stops, use a
compression nut and compression sleeve to connect inlet end of
Bak-Chek to the Supply Stop.
NOTE: Failure to install the Bak-Chek can result in a cross ow
connection when the faucet is in the off position and the supply stops
are open. If the pressures of the hot water supply and the cold water
supply are different, hot water can migrate into the cold water supply
or cold water can migrate into the hot water supply. Most plumbing
codes require that the Bak-Chek be used to prevent this occurance.
A
B
3/8” (10 mm)
BAK-CHEK TEE
3/8” (10 mm)
SUPPLY TUBE
3/8” (10 mm)
COMPRESSION FITTING

2A - INSTALL EBF-625 FAUCET
NOTE: Sloan Valve Company reccomends that this faucet is installed
with our trim plate. Our trim plate includes an anti-rotation feature to
prevent rotary motion of this single-hole pedestal-style faucet.
Slide faucet base gasket over faucet shank and sensor cable.
Install optional trim plate next followed by the trim plate gasket. Holding
the faucet base gasket and optional trim plate assembly in place, insert
sensor cable and faucet shank through the 1” (25 mm) center hole in
deck lavatory. Use plumber’s putty to secure optional trim plate.
Thread sensor cable through side of mounting spacer, and then secure
faucet to deck or lavatory using the mounting washer, lock washer and
nut. Apply thread sealant or Teon tape to threads at end of faucet
shank.
2B - INSTALL EBF-655 FAUCET
NOTE: Refer to the Installation Instructions included
with the ETF-578-A trim plate for addtional information
about using an 8” trim plate with an EBF-655 faucet.
Slide faucet base gasket onto faucet.
Insert faucet sensor cable, pipe nipple, and mounting studs through the
4” (102 mm) spread deck holes. Secure faucet to deck using slotted
mounting washers and wing nuts supplied.
3 - MOUNT CONT OL MODULE TO WALL
IMPORTANT: DO NOT install control module upside down. The
control module may be oriented so that it faces sideways (vertically);
however, optimum performance is obtained when the control module is
horizontal with the Sloan logo on the cover facing up.
Install the control module in an appropriate location. All four (4) cover
screws must be accessible from the chosen mounting position. After
installation, the cable from spout to control module should have
some slack.
Remove control module cover from control module base. Use the control
module base as a template to mark locations on wall for mounting
fasteners. Determine the appropriate mounting fastener for the particular
wall type (three different fastener types are included; see parts list). Drill
four (4) appropriately sized holes.
For plastic wall anchor – 1/4” (6 mm) holes
For hollow wall anchor – 5/16” (8 mm) holes
For toggle nut anchor – 3/8” (10 mm) holes
Install 3/8” compression tting on end of faucet shank.
FAUCET
BASE GASKET
FAUCETSENSOR
CABLE
1/4" NPT PIPE
NIPPLE
1/4" NPT PIPETO3/8"
TUBE COMPRESSION
FITTING
MOUNTING
SPACER
FLAT WASHER
LOCKWASHER
MOUNTING NUT
FAUCET
SLOTTED MOUNTING
WASHERS(2)
WINGNUTS (2)
MOUNTING STUDS
FAUCET SENSOR
CABLE
1/8" NPTPIPE
NIPPLE
BASE GASKET
A
B
C
D
A
B
A
B
CAttach Control Module base to wall using appropriate fastener.
DRILL FOUR HOLESINTOWALL
USING MOUNTINGFASTENERS
APPROPRIATE FOR THE
PARTICULAR WALL TYPE:
•PLASTIC WALL ANCHOR—
1/4" (6 mm)HOLE
•HOLLOWWALL ANCHOR—
5/16" (8 mm)HOLE
• TOGGLE NUT ANCHOR—
3/8" (10 mm)HOLE
CONTROL
MODULE
WALL
PLASTIC ANCHOR
WITH SCREW AND
WASHER SHOWN
3-1/2"
(89mm)
4-3/8"
(111 mm)