SMAI Ski Machine User manual

SKI MACHINE FLOOR STAND ASSEMBLY

2
Table of Contents
GENERAL PARTS INDENTIFICATION PAGE 3
ASSEMBLY INSTRUCTION PAGE 4-9
EXPLODED DRAWING PAGE 10
PART LIST PAGE 11
(2019/ 06) (SF-01)

3
FLOOR STAND ASSEMBLY
GENERAL PARTS IDENTIFICATION
1
MOUNTING BRACKET(A07) X 1PC (WILL BE INCLUDED AT THE
HARDWARE PACK OF THE MAIN SKIER)
2
HANDRAIL(A11) X1PC
3
HANDRAIL BRACKET (A12) X1PC
4
1/4-20 X 1-1/4” BUTTON HEAD SOCKET SCREW(STAINLESS) (B18)
X 8PCS
5
1/4-20 X 1/2” BUTTON HEAD SOCKET SCREW(STAINLESS) (B19)
X6PCS
6
1/4 T-NUT NO PRONGS(STAINLESS) (C06) X 4PCS
7
ANTI SKID WOODEN BASE(G31) X 1 PC
8
TOOL (4MM HEX HEAD SCREWDRIVER) X 1PC
(WILL BE INCLUDED AT THE HARDWARE PACK OF THE MAIN
SKIER)
WILL BE INCLUDED AT THE
HARDWARE PACK OF THE MAIN SKIER

4
ASSEMBLY INSTRUCTION
Step 1
With the Wooden Base(G31) upside down, position the Mounting bracket(A07) to the Wooden
Base(G31) as shown.
From the underside of the wooden base, Insert the T-nuts(C06) into the holes of Mounting
bracket (A07). Use a hammer to fully seat the T-nuts (C06) into the holes on Wooden Base(G31)
firmly as shown.
Finally lay the assembled wooden base with Mounting Bracket assy on its bottomin preparation
for mounting the AIR SKIER
FIGURE 1

5
ASSEMBLY INSTRUCTION
Step 1
Remove the two pre-installed Screws(B19) from lower portion of the AIR SKIER as shown.
You will reinstall these in the next step.
FIGURE2

6
ASSEMBLY INSTRUCTION
Step 1
Carefully place the AIR SKIER on the wooden base (G31) so that it lines up with the four inner
holes on the wooden base (G31). Fasten four Washers(D06) and Screws(B18) to insert
through each of the four holes in the Air Skier Bottom Bracket (A01) and into the Wooden
Base (G31) .Next tighten all Washers (D06) and Screws (B18) with Wooden Base (G31) and
Air Skier Bottom Bracket(A01) firmly as diagram .
Step 2
Assemble the additional two Screws(B18) and Washers (D06) and insert through the top of the
wooden base and into the Mounting Bracket (A07) in two of the outside holes as shown.

7
ASSEMBLY INSTRUCTION
Step 1
Fasten four screws(B19) and insert through each of the four holes in the AIR SKIER mounting
bracket (A07), then tighten firmly as show.
FIGURE 4

8
ASSEMBLY INSTRUCTION
STEP 1
Secure the Handrail (A11) to the Wooden Base(G31) on each side by using the screws(B18)
and Washers(D06) as shown.
STEP 2
Loosely attach the Handrail Bracket(A12) to the Handrail (A11) using four Screws (B19) as
diagram. Once all four Screws (B19) are in place, tighten the Handrail Bracket (A12) fully to the
Air Skier as shown.
FIGURE 5

9
ASSEMBLY INSTRUCTION
FIGURE 6
Congratulations!
You have completed the assembly of your Air Skier with
Floor Stand
Before using the machine , please do some warm-up exercise to prevent any muscle
cramp .

10
Exploded View
WILL BE INCLUDED AT THE
HARDWARE PACK OF THE MAIN SKIER

11
Part List (FLOOR STAND )
NO.
PART NAME
QTY
A11
HANDRAIL
1
A12
HANDRAIL BRACKET
1
B18
1/4-20*1-1/4”BUTTON HEAD SOCKET SCREW(STAINLESS)
8
B19
1/4-20*1/2”BUTTON HEAD SOCKET SCREW(STAINLESS)
6
B20
ψ5.5mm*1 PHILLIPS FLAT HEAD TAPPING
SCREW(STAINLESS)
4
B21
4*16mm SCREW(BLACK)
2
C06
1/4 T-NUT NO PRONGS(STAINLESS)
8
D06
ψ19*ψ6.5*1.5t FLAT WASHER(BLACK)
8
G29
RIGHT CASTER
1
G30
LEFT CASTER
1
G31
ANTI SKID WOODEN BASE
1
G32
FOOT ROUND PAD
4