SMART-AVI XT-TX400 User manual

UXGA, STEREO AUDIO, IR AND
RS-232 POINT-TO-MULTIPOINT
CAT5 4-PORT TRANSMITTER
USE A SINGLE CAT5 CABLE TO
BROADCAST HIGH-RESOLUTION
SXGA, STEREO AUDIO, RS232
AND IR TO 4 STATIONS
UP TO 1,000 FT AWAY
Quick Start Guide
VIDEO
Format RGBHV, RGsB, YUV, Y/C, CVBS
Resolution Up to 1900 x 1200 VGA, SVGA, XGA,
SXGA
Connector Type HD 15 socket
AUDIO
Signal Type Stereo unbalanced
Connector 3.5 mm jack socket
RS-232
Format DB9M
Speed Up to 9600 bps
IR
Interface (1) 3.5 mm (Female)
IR Frequency Range 30KHz to 80KHz
Emitter Distance Up to 10’
Connector 3.5mm Stereo jack for emitter and
IR eye
OTHER
Power Supply 5VDC @.5A
Dimensions 8.6” W x 4.6” D x 1” H
(1.2” with pegs)
Weight .8 lbs
Operating Temp. 0 to 40°C (32° to 104° F)
Storage Temp. -20° to 60°C (-4° to 140° F)
Humidity Up to 95% (non-condensing)
NOTICE
The information contained in this document is
subject to change without notice. SmartAVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
SmartAVI will not be liable for errors contained
herein or for incidental or consequential damages in
connection with the furnishing, performance or use of
this material.
No part of this document may be photocopied,
reproduced, or translated into another language
without prior written consent from SmartAVI
Technologies, Inc.
800.AVI.2131, 702.800.0005
2455 W Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
SmartAVI.com
TECHNICAL SPECIFICATION
XT-TX400
WHAT’S IN THE BOX
PART NO. Q-TY DESCRIPTION
XT-TX400S 1
UXGA, Stereo Audio, IR and
RS-232 Point-to-Multipoint
CAT5 4-Port Transmitter
CCVGAMM06 1 6 Feet VGA Cable
PS5VD2A 1 PS5VD2A power supply
Quick Start Guide 1

ABOUT UX-PLUS
The XT-TX400 range of products allows the extension of
a wide range of video and audio formats and RS232 up to
4 locations using Category 5 Unshielded Twisted Pair (UTP)
cables. With RS232 communication support the XT-TX400
allows users to send commands to single or multiple
devices. This allows the user to change the volume,
channel or turn on/off the display panel remotely.
FEATURES
• Supports Local Screen.
• Uses easy to install, inexpensive CAT-5/5e/6/7/8.
• Each output reaches up to 1,000 feet (300 m).
• Supports high resoluon video up to 1920x1200
• HDTV Compable (720p, 1080i,1080p) 300 MHz
Bandwidth
• Sends high-resoluon VGA, Stereo Audio signals,
RS232 or IR from one source to 4 locaons
• Compable with VGA, XGA, Sun, MAC and SGI Sync
Format / Polarity Preservaon
• Compable with Line Level Stereo Audio Signals
• High ground loop immunity
• Built-in power surge and transient protecon
• Designated trimmer in the remote unit to compen-
sate for cable length
• Compact Metal Case Enclosure
• External power supply.
• RS-232c Communicaon support to single or mul-
ple Displays
• IR command to single or mulple Displays EDID
Emulator
1. Connect the output of the computer video card to the video input of the transmitter using the included male to male video
cable.
2. Optionally connect the output of the computer audio card to the audio input of the transmitter using 3.5mm audio male to
male audio cable.
3. Connect local monitor to the VGA out of the transmitter.
4. Optionally connect external speakers to the transmitter’s audio out (Standard 3.5mm stereo miniplug).
5. Connect CAT5 cables to outputs 1-4.
NOTE: You can not use RS232 and IR at the same time.
6. Connect CAT5 cable (coming from the transmitter) to the back of the receiver.
7. Connect 1-4 display monitors to the VGA out connectors on the receiver.
8. Optionally connect 1-4 sets of external speakers to the audio connectors on the receiver. (Standard 3.5mm stereo
Miniplug)
HARDWARE INSTALLATION
FROND AND BACK
DVI IN
DVI OUT
AUDIO IN
AUDIO OUT
IR IN
IR OUT
RS232
CAT5e/6
SmartAVI Web
Controller
XT-TX400
SmartAVI Web
Controller
SmartAVI Web
Controller
SmartAVI Web
Controller
1000 ft
1000 ft
1000 ft
1000 ft
SmartAVI Web
Controller
XTP-RX
XTP-RX
XTP-RX
XTP-RX