SMART Embedded Computing RTM-ATCA-736x-10G Series Quick start guide

RTM-ATCA-736x-10G
Installation and Use
P/N: 6806800P29G
December 2020

© 2020 SMART Embedded Computing™, Inc.
All Rights Reserved.
Trademarks
The stylized "S" and "SMART" is a registered trademark of SMART Modular Technologies, Inc. and “SMART Embedded
Computing” and the SMART Embedded Computing logo are trademarks of SMART Modular Technologies, Inc. All other names
and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. These materials are
provided by SMART Embedded Computing as a service to its customers and may be used for informational purposes only.
Disclaimer*
SMART Embedded Computing (SMART EC) assumes no responsibility for errors or omissions in these materials. These
materials are provided "AS IS" without warranty of any kind, either expressed or implied, including but not limited to,
the implied warranties of merchantability, fitness for a particular purpose, or non-infringement. SMART EC further does
not warrant the accuracy or completeness of the information, text, graphics, links or other items contained within these
materials. SMART EC shall not be liable for any special, indirect, incidental, or consequential damages, including without
limitation, lost revenues or lost profits, which may result from the use of these materials. SMART EC may make changes to
these materials, or to the products described therein, at any time without notice. SMART EC makes no commitment to update
the information contained within these materials.
Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a
URL to a SMART EC website. The text itself may not be published commercially in print or electronic form, edited, translated,
or otherwise altered without the permission of SMART EC.
It is possible that this publication may contain reference to or information about SMART EC products, programming, or services
that are not available in your country. Such references or information must not be construed to mean that SMART EC intends
to announce such SMART EC products, programming, or services in your country.
Limited and Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply
unless otherwise agreed to in writing by SMART Embedded Computing.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in
Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and
Documentation clause at DFARS 252.227-7014 (Jun. 1995).
SMART Embedded Computing, Inc.
2900 S. Diablo Way, Suite 190
Tempe, Arizona 85282
USA
*For full legal terms and conditions, visit www.smartembedded.com/ec/legal

Table of Contents
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 3
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.3 Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.4 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.5 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.6 Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2 Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.1 Unpacking and Inspecting the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.2 Environmental and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.2.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.2.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.3 Installing the Hard Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.4 Replacing the Hard Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.5 Installing and Removing the RTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.5.1 Installing the RTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.5.2 Removing the RTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.6 Installing and Removing SFP/SFP+ Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.6.1 Installing an SFP/SFP+ Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.6.2 Removing an SFP/SFP+ Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3 Controls, LEDs, and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1 Mechanical Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.2 Face Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.2.1 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.2.2 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.2.3 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
Table of Contents
3.2.3.1 Ethernet Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.2.3.2 SAS Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.3 ATCA Backplane Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4 Sensor Data Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
A Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
A.1 SMART Embedded Computing Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
A.2 Manufacturers’ Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
A.3 Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

List of Figures
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 5
Figure 1-1 RTM Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 1-2 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-1 Location of Critical Temperature Spots (Top Side) . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2-2 Inserting the Hard Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 3-1 Mechanical Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-2 Face Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 3-3 Location of LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-4 Location of Face Plate Reset Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 3-5 Location of Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 3-6 Location of SAS Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 3-7 SAS Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 3-8 Location of AdvancedTCA Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

List of Figures
6 RTM-ATCA-736x-10G Installation and Use (6806800P29G)

List of Tables
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 7
Table 1-1 Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 1-2 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 2-1 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 2-2 Critical Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-3 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 2-4 SFP/SFP+ Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 3-1 Face Plate LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3-2 Ethernet Controller Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 4-1 Sensor Data Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table A-1 SMART EC Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table A-2 Manufacturer’s Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table A-3 Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

List of Tables
8 RTM-ATCA-736x-10G Installation and Use (6806800P29G)

RTM-ATCA-736x-10G Installation and Use (6806800P29G) 9
About this Manual
Overview of Contents
This Reference Guide is intended for users qualified in electronics or electrical engineering.
Users must have a working understanding of Peripheral Component Interconnect (PCI),
AdvancedTCA®, and telecommunications.
The manual contains the following chapters and appendices:
Safety Notes on page 15 lists safety notes applicable to the blade.
Sicherheitshinweise on page 19 provides the German translation of the safety notes
section.
Chapter 1, Introduction on page 23 describes the main features of the blade.
Chapter 2, Hardware Preparation and Installation on page 27 outlines the installation
requirements, hardware accessories, switch settings, installation and removal procedures.
Chapter3,Controls,LEDs, and Connectors on page 43 describes external interfaces of the
blade. This includes connectors and LEDs.
Chapter 4, Sensor Data Records on page 53 provides information on the blade’s FRU info
and sensor data.
Appendix A, Related Documentation on page 55 provides links to further blade-related
documentation.
Abbreviations
This document uses the following abbreviations:
Abbreviation Definition
ANSI American National Standards Institute
ATCA Advanced Telecommunications Computing Architecture
ATN Attention
BMC Baseboard Management Controller
CISPR Comité Internationale Spécial des Perturbations
Radioelectrotechnique
CMD Command
EMC Electromagnetic Compatibility
EMV Elektromagnetische Vertraeglichkeit

10 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
About this Manua
l
About this Manual
EN European Norm
ETH Ethernet
ETSI European Telecommunications Standards Institute
ESD Electrostatic Sensitive Device
FAE Field Application Engineers
FCC Federal Communications Commission
FRU Field Replaceable Unit
GB Gigabyte
GbE Gigabit Ethernet
GmbH Gesellschaft mit beschraenkter Haftung
HDD Hard Disk Drive
H/S Hot Swap
HPM Hardware Platform Management
IANA Internet Assigned Numbers Authority
ID Identifier
IEC International Electric Code
IEEE Institute of Electrical and Electronics Engineers
IPMB Intelligent Platform Management Bus
IPMC Intelligent Platform Management Controller
IPMI Intelligent Platform Management Interface
ISO International Organization for Standardization
JBOD Just a Bunch Of Disks
KCS Keyboard Controller Style
LSB Least Significant Bit/Byte
LUN Logical Unit Number
MMC Mezzanine Management Controller
NEBS Network Equipment Building System
Abbreviation Definition

About this Manual
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 11
Conventions
The following table describes the conventions used throughout this manual.
NetFn Network Function
OEM Original Equipment Manufacturer
OOS Out-Of-Service
PCB Printed Circuit Board
PCI Peripheral Component Interconnect
PICMG PCI Industrial Computer Manufacturers Group
RAID Redundant Array of Inexpensive Disks
RoHS Restriction of Hazardous Substances
RPM Rounds per Minute
RTM Rear Transition Module
SAS Serial Attached SCSI
SATA Serial ATA
SDR Sensor Data Record
SELV Safety Extra Low Voltages
SFP Small Form-Factor Pluggable
UL Underwriters Laboratory Inc.
USB Universal Serial Bus
VCCI Voluntary Control Council for Interference
Abbreviation Definition
Notation Description
0x00000000 Typical notation for hexadecimal numbers (digits are 0 through F), for
example used for addresses and offsets
0b0000 Same for binary numbers (digits are 0 and 1)
bold Used to emphasize a word

12 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
About this Manua
l
About this Manual
Screen Used for on-screen output and code related elements or commands.
Sample of Programming used in a table (9pt)
Courier + Bold Used to characterize user input and to separate it from system output
Reference Used for references and for table and figure descriptions
File > Exit Notation for selecting a submenu
<text> Notation for variables and keys
[text] Notation for software buttons to click on the screen and parameter
description
... Repeated item for example node 1, node 2, ..., node 12
.
.
.
Omission of information from example/command that is not necessary at
the time
.. Ranges, for example: 0..4 means one of the integers 0,1,2,3, and 4 (used
in registers)
| Logical OR
Indicates a hazardous situation which, if not avoided, could result in death
or serious injury
Indicates a hazardous situation which, if not avoided, may result in minor
or moderate injury
Indicates a property damage message
Indicates a hot surface that could result in moderate or serious injury
Notation Description

About this Manual
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 13
Summary of Changes
This manual has been revised and replaces all prior editions.
Indicates an electrical situation that could result in moderate injury or death
Indicates that when working in an ESD environment care should be taken
to use proper ESD practices
No danger encountered, pay attention to important information
Notation Description
Part Number Publication
Date Description
6806800P29G December 2020 Updated Table 1-1 for 62368-1 compliance.
6806800P29F October 2019 Rebrand to SMART Embedded Computing. Updated
RoHS directive.
6806800P29E July 2016 Removed declaration of conformity. Updated
copyrights information page.
6806800P29D September 2015
Updated Chapter 1.3 Standard Compliance on page
27. Updated Safety Notes Summary and
Sicherheitshinweise.
6806800P29C June 2014 Re-branded to Artesyn.
6806800P29B December 2012 Updated Chapter 1, Standard Compliances, on page
26 and Power Dissipation table on page 33.
6806800P29A June 2012 First edition

14 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
About this Manua
l
About this Manual

RTM-ATCA-736x-10G Installation and Use (6806800P29G) 15
Safety Notes
This section provides warnings that precede potentially dangerous procedures throughout
this manual. Instructions contained in the warnings must be followed during all phases of
operation, service, and repair of this equipment. You should also employ all other safety
precautions necessary for the operation of the equipment in your operating environment.
Failure to comply with these precautions or with specific warnings elsewhere in this manual
could result in personal injury or damage to the equipment.
SMART Embedded Computing (SMART EC) intends to provide all necessary information
to install and handle the product in this manual. Because of the complexity of this product
and its various uses, we do not guarantee that the given information is complete. If you
need additional information, ask your SMART EC representative.
The product has been designed to meet the standard industrial safety requirements. It must
not be used except in its specific area of office telecommunication industry and industrial
control.
Only personnel trained by SMART EC or persons qualified in electronics or electrical
engineering are authorized to install, remove or maintain the product.
The information given in this manual is meant to complete the knowledge of a specialist and
must not be used as replacement for qualified personnel.
Keep away from live circuits inside the equipment. Operating personnel must not remove
equipment covers. Only factory authorized service personnel or other qualified service
personnel may remove equipment covers for internal subassembly or component
replacement or any internal adjustment.
Do not install substitute parts or perform any unauthorized modification of the equipment or
the warranty may be voided. Contact your local SMART EC representative for service and
repair to make sure that all safety features are maintained.
EMC
The blade has been tested in a standard SMART EC system and found to comply with the
limits for a Class A digital device in this system, pursuant to part 15 of the FCC Rules, EN
55022 Class A respectively. These limits are designed to provide reasonable protection
against harmful interference when the system is operated in a commercial environment.
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Interference (VCCI). If this equipment is used in a
domestic environment, radio disturbance may arise. When such trouble occurs, the user
may be required to take corrective actions.

16 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
Safety Notes
Safety Notes
The blade generates and uses radio frequency energy and, if not installed properly and
used in accordance with this guide, may cause harmful interference to radio
communications. Operating the system in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own
expense.
Installation
Damage of Circuits
Electrostatic discharge and incorrect blade installation and removal can damage circuits or
shorten their life.
Before touching the blade or electronic components, make sure that you are working in an
ESD-safe environment.
Data Loss
Removing the blade with the blue LED still blinking causes data loss.
Wait until the blue LED is permanently illuminated, before removing the blade.
Damage of Blade and Additional Devices and Modules
Incorrect installation of additional devices or modules may damage the blade or the
additional devices or modules.
Before installing or removing an additional device or module, read the respective
documentation.
System Damage
Warning: The intra-building port (s) of the equipment or subassembly is suitable for
connection to intra-building or unexposed wiring or cabling only. The intra-building port (s)
of the equipment or subassembly MUST NOT be metallically connected to interfaces that
connect to the outside plant (OSP) or its wiring. These interfaces are designed for use as
intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089) and require
isolation from the exposed OSP cabling. The addition of primary protectors is not sufficient
protection in order to connect these interfaces metallically to OSP wiring.
The intra-building port(s) of the equipment or subassembly must use shielded intra-building
cabling/wiring that is grounded at both ends.

Safety Notes
RTM-ATCA-736x-10G Installation and Use (6806800P29G) 17
Operation
Blade Damage - Blade Surface
High humidity and condensation on the blade surface causes short circuits.
Do not operate the blade outside the specified environmental limits. Make sure the blade
is completely dry and there is no moisture on any surface before applying power.
Blade Overheating and Blade Damage
Operating the blade without forced air cooling may lead to blade overheating and thus
blade damage.
When operating the blade, make sure that forced air cooling is available in the shelf.
When operating the blade in areas of electromagnetic radiation ensure that the blade is
bolted on the system and the system is shielded by enclosure.
Environment
Always dispose of used blades, system components and RTMs according to your country’s
legislation and manufacturer’s instructions.
SFP Modules
Personal Injury and Damage of the RTM and SFP Modules
Installing and using SFP modules which are not fully certified and which do not meet all
relevant safety standards may damage the RTM and the SFP modules and may lead to
personal injury.
Only use and install SFP modules which are fully certified and which meet all relevant
safety standards.
Personal Injury
Optical SFP modules may be classified as laser products. When installing and using any
of these SFP modules, the regulations which correspond to the respective laser class apply
to the whole RTM. Not complying to these regulations may lead to personal injury.
When installing and using optical SFP modules which are classified as laser products,
make sure to comply to the respective regulations.
Eye Damage
Optical SFP modules may emit laser radiation when no cable is connected. This laser
radiation is harmful to your eyes. Do not look into the optical lens at any time.

18 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
Safety Notes
Safety Notes
SFP Module Damage
The optical port plug protects the optical fibres against dirt and damage. Dirt and damage
can render the SFP module inoperable.
Only remove the optical plug when you are ready to connect a cable to the SFP module.
When no cable is connected, cover the port with an optical port plug.

RTM-ATCA-736x-10G Installation and Use (6806800P29G) 19
Sicherheitshinweise
Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses
Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs, der
Wartung und der Reparatur des Systems die Anweisungen, die diesen Hinweisen
enthalten sind. Sie sollten außerdem alle anderen Vorsichtsmaßnahmen treffen, die für den
Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind. Wenn Sie diese
Vorsichtsmaßnahmen oder Sicherheitshinweise, die an anderer Stelle diese Handbuchs
enthalten sind, nicht beachten, kann das Verletzungen oder Schäden am Produkt zur Folge
haben.
SMART Embedded Computing (SMART EC) ist darauf bedacht, alle notwendigen
Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit
zu stellen. Da es sich jedoch um ein komplexes Produkt mit vielfältigen
Einsatzmöglichkeiten handelt, können wir die Vollständigkeit der im Handbuch enthaltenen
Informationen nicht garantieren. Falls Sie weitere Informationen benötigen sollten, wenden
Sie sich bitte an die für Sie zuständige Geschäftsstelle von SMART EC.
Das System erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf
ausschließlich für Anwendungen in der Telekommunikationsindustrie und im
Zusammenhang mit Industriesteuerungen verwendet werden.
Einbau, Wartung und Betrieb dürfen nur von durch SMART EC ausgebildetem oder im
Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die in
diesem Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von
Fachpersonal zu ergänzen, können dieses jedoch nicht ersetzen.
Halten Sie sich von stromführenden Leitungen innerhalb des Produktes fern. Entfernen Sie
auf keinen Fall Abdeckungen am Produkt. Nur werksseitig zugelassenes
Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen
entfernen, um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen.
Installieren Sie keine Ersatzteile oder führen Sie keine unerlaubten Veränderungen am
Produkt durch, sonst verfällt die Garantie. Wenden Sie sich für Wartung oder Reparatur
bitte an die für Sie zuständige Geschäftsstelle von SMART EC. So stellen Sie sicher, dass
alle sicherheitsrelevanten Aspekte beachtet werden.
EMV
Das Blade wurde in einem SMART EC Standardsystem getestet. Es erfüllt die für digitale
Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCC-
Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen einen
angemessenen Schutz vor Störstrahlung beim Betrieb des Blades in Gewerbe- sowie
Industriegebieten gewährleisten.

20 RTM-ATCA-736x-10G Installation and Use (6806800P29G)
Sicherheitshinweise
Sicherheitshinweise
Das Blade arbeitet im Hochfrequenzbereich und erzeugt Störstrahlung. Bei
unsachgemäßem Einbau und anderem als in diesem Handbuch beschriebenen Betrieb
können Störungen im Hochfrequenzbereich auftreten.
Warnung! Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt werden,
angemessene Maßnahmen durchzuführen.
Installation
Beschädigung von Schaltkreisen
Elektrostatische Entladung und unsachgemäßer Ein- und Ausbau von Blades kann
Schaltkreise beschädigen oder ihre Lebensdauer verkürzen.
Bevor Sie Blades oder elektronische Komponenten berühren, vergewissern Sie sich, daß
Sie in einem ESD-geschützten Bereich arbeiten.
Datenverlust
Wenn Sie das Blade aus dem Shelf herausziehen, und die blaue LED blinkt noch, gehen
Daten verloren.
Warten Sie bis die blaue LED durchgehend leuchtet, bevor Sie das Blade herausziehen.
Beschädigung des Blades und von Zusatzmodulen
Fehlerhafte Installation von Zusatzmodulen, kann zur Beschädigung des Blades und der
Zusatzmodule führen.
Lesen Sie daher vor der Installation von Zusatzmodulen die zugehörige Dokumentation.
Beschädigung des Systems
Warnung: Die intra-Gebäude Port (s) des Geräts oder Baugruppe ist für den Anschluss an
den inner Gebäude oder unbelichteten Verdrahtung oder Verkabelung nur. Die intra-
Gebäude Port (s) des Geräts oder Baugruppe muss nicht metallisch mit Schnittstellen, die
an der Außenanlage (OSP) oder dessen Verkabelung anschließen angeschlossen
werden. Diese Schnittstellen sind für die Verwendung als intra Gebäude Schnittstellen nur
entworfen, (Typ 2 oder Typ 4 Ports wie in GR-1089 beschrieben) und erfordern Isolierung
von der freiliegenden OSP-Verkabelung. Die Zugabe von primären Schutz nicht
ausreichenden Schutz, um diese Schnittstellen metallisch mit OSP Verdrahtung verbinden.
Die intra-Gebäude Port (s) des Gerätes oder einer Unterbaugruppe müssen abgeschirmte
innerGebäudeVerkabelung / Verdrahtung, die an beiden Enden geerdet ist zu verwenden.